Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite materials testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

3D X-ray Microprobe Investigation of Local Dislocation Densities and Elastic Strain Gradients in a NiAl-Mo Composite and Exposed Mo Micropillars as a Function of Pre-strain

3D spatially-resolved polychromatic microdiffraction was used to nondestructively probe the depth-dependent dislocation density and elastic strain gradients in separate phases of a NiAl Mo composite. Dislocation density and strain gradients are investigated before and after compressive strain. After plastic deformation important changes in the local stress state are found compared to the as grown composite. In as grown composites, due to the thermal expansion mismatch, the Mo phase is under compression and the NiAl phase is in tension. After compressive strain, the Mo phase is in tension and NiAl matrix is under compression. This result can be understood from the mismatch in yield strain of the composite material and from the elastic constraints during unloading. The dislocation density in both phases is found to grow with increased straining. These measurements provide quantitative dislocation information to guide recent directional solidified Mo micro-pillar testing. They also guide models of interface dynamics in composite materials.

36 MATERIALS SCIENCE↗

Synthesis and testing of a composite membrane based on sulfonated polyphenylene oxide and silica compounds as proton exchange membrane for PEM fuel cells

Highlights: • A material based on composite poly (phenylene oxide)/ silica was synthesized and tested as PEM for Hydrogen Fuel Cells. • Sol-gel method has been used to generate silica particles inside the polymer matrix • The presence of silica inside the membrane was highlighted by Energy Dispersive X-ray Fluorescence (EDXRF) spectroscopy. • This membrane has improvements related to: water retention, extension by hydration and tensile strength in hydrated state silica particles inside the polymer matrix • The presence of silica inside the membrane was highlighted by Energy Dispersive X-ray Fluorescence (EDXRF) spectroscopy. • This membrane has improvements related to: water retention, extension by hydration and tensile strength in hydrated state. - Abstract: The present work is an attempt to improve the usseful properties of sulfonated polyphenylene oxide in order to obtain a proton exchange membrane (PEM) for proton exchange membrane fuel cells(PEMFC). Formation of siloxane compounds inside the polymer matrix through an in situ sol-gel process improves properties of the composite membrane: water retention, tensile strength and dimensional stability of the membrane. The presence of the silicone atoms inside the polymer matrix is highlited in the X-ray fluorescence spectra. Parameters related to water absorbtion and proton transport inside the membrane such as: water uptake, hydration number (λ), dimensional expansion by hydration, ion exchange capacity and sulfonation degree show an optimization of the composite membrane compared to the polymeric one. Furthermore, the tensile strength of the composite membranes is better than the polymeric one when both samples are fully hydrated.

36 MATERIALS SCIENCE↗

A bilinear failure criterion for mixed-mode delamination

Many different failure criteria have been suggested for mixed-mode delamination toughness, but few sets of mixed-mode data exist that are consistent over the full range of Mode 1 opening load to Mode 2 shear load range. The mixed-mode bending (MMB) test was used to measure the delamination toughness of a brittle epoxy composite, a state-of-the-art toughened epoxy composite, and a tough thermoplastic composite over the full mixed-mode range. To gain insight into the different failure responses of the different materials, the delamination fracture surfaces were also examined. An evaluation of several failure criteria that have been reported in the literature was performed, and the range of responses modeled by each criterion was analyzed. A bilinear failure criterion was introduced based on a change in the failure mechanism observed from the delamination surfaces. The different criteria were compared to the failure response of the three materials tested. The responses of the two epoxies were best modeled with the new bilinear failure criterion. The failure response of the tough thermoplastic composite could be modeled well with the bilinear criterion but could also be modeled with the more simple linear failure criterion. Since the materials differed in their mixed-mode failure response, mixed-mode delamination testing will be needed to characterize a composite material. This paper presents consistent sets of mixed-mode data, provides a critical evaluation of the mixed-mode failure criteria, and should provide general guidance for selecting an appropriate criterion for other materials.

Reeder, James R.↗

Application of IR Thermography with Thermal Diffusivity Analysis for Detection of Plies Displacement in CFRP Composites

This paper presents an efficient nondestructive testing (NDT) method for detection of plies displacement in carbon fiber reinforced plastic (CFRP) composites using the active thermography technique. To assess the capability of the proposed technique for detection of plies displacement, the CFRP composite specimens with simulated fault were designed and manufactured. The IR thermography measurements were conducted using two-sided experimental arrangement. From recorded sequences of thermal images, the temperature variations versus time plots were extracted to obtain the maximum thermal contrasts. For quantitative interpretation of the results, the thermal diffusivity values for each composite material were determined and related to the fiber volume fraction. The experimental results showed that the thermal diffusivity increases with an increase of fiber volume fraction; further, the values of thermal diffusivity are specimen thickness dependent. The obtained values of thermal diffusivity varied from 1.5 × 10{sup −7} m{sup 2}/s (for 3.2 mm composite with 8.5 vol.% carbon fiber) to 2.6 × 10{sup −7} m{sup 2}/s (for 7.7 mm composite with 34.1 vol.% carbon fiber). On the basis of these results, it was concluded that the active thermography combined with thermal diffusivity analysis can be considered as a reliable NDT technique for detection of plies displacement in CFRP composites.

36 MATERIALS SCIENCE↗

Space Aging of Solid Rocket Materials (P0005)

The objective of this experiment is to determine the effects of long-term orbital exposure on the materials used in solid-rocket space motors. Specifically, structural materials and propellants from the STAR/PAM-D series motors and the PAM DII/IPSM-II motors will be tested, as well as advanced composite case and nozzle materials planned for future use. The experiment approach is to expose samples of solid-rocket propellant, liner, insulation, case, and nozzle specimens to the space environment and to compare preflight and postflight measurements of various mechanical, chemical, and ballistic properties.

Leon L Jones↗

Advanced composite aileron for L-1011 transport aircraft: Design and analysis

Detail design of the composite aileron has been completed. The aileron design is a multi-rib configuration with single piece upper and lower covers mechanically fastened to the substructure. Covers, front, spar and ribs are fabricated with graphite/epoxy tape or fabric composite material. The design has a weight savings of 23 percent compared to the aluminum aileron. The composite aileron has 50 percent fewer fasteners and parts than the metal aileron and is predicted to be cost competitive. Structural integrity of the composite aileron was verified by structural analysis and an extensive test program. Static, failsafe, and vibration analyses have been conducted on the composite aileron using finite element models and specialized computer programs for composite material laminates. The fundamental behavior of the composite materials used in the aileron was determined by coupon tests for a variety of environmental conditions. Critical details of the design were interrogated by static and fatigue tests on full-scale subcomponents and subassemblies of the aileron.

Griffin, C. F.↗

Composite Technology for Exploration (CTE)

The CTE project is developing and demonstrating weight-saving, performance-enhancing composite bonded joint technology by incorporating materials characterization studies into the design, manufacturing, and testing of lightweight composite bonded joint concepts for SLS-scale applications. The project is advancing current high-fidelity analysis tools and standards for improvements in the prediction of failure and residual strength of bonded joints.

Composite Technology↗

Experimental Investigation on the Performance Loss of Cross-Linked Polymers During Photo-Oxidative Aging

Abstract Polymeric substances have seen an unprecedented integration in countless applications and fields of life, subjecting them to a broad range of environmental conditions, which can cause a form of damage to the structural and mechanical properties of these components known as aging. In this study we investigate the effects of the degradation of polymeric materials due to the extended exposure to sunlight, which can be simulated through controlled photo-oxidative aging using ultraviolet (UV) radiation as the main catalyst of this phenomenon. The effects on mechanical behavior and chemical properties of four polymeric materials with different mechanical characteristics was accordingly monitored throughout the study. The materials range in hardness with the polyurethane adhesive being the hardest and acting plastically, followed by an acrylic which exhibits greater hardening with time, a polyurethane sealant, which behaves in an elastomeric manner, and a silicon sealant, which is the softest of the set. Samples were prepared and subjected to UV radiation at three different temperatures namely 45, 60 and 80°C, for different aging periods ranging from 1 day for higher temperatures to 150 days for lower ones. The samples were then subjected to the Fourier transform Infrared spectroscopy (FTIR) test to monitor the change in the chemical composition of the materials along the aging durations and conditions. The materials were then subjected to mechanical testing along two modes of mechanical loading, which are a simple tension until failure and a double-cyclic test with progressively increasing strain limits after every two successful cycles until the sample reaches failure. The samples are loaded at constant strain rates throughout both tests. These tests revealed the change of behavior of our materials along the aging periods and conditions. The changes in mechanical behavior vary across each individual material depending on the aging temperature and period, with the changes ranging from hardening to softening, embrittlement or an increase in the maximum strain the material can endure before failure. A general trend would be that most materials become harder after photo-oxidation, however due to the range of temperatures in the aging conditions, thermo-oxidation, which causes softening in some of the polymers, has an increasingly notable effect at higher temperatures. A visible correlation can be noted between the change in mechanical behavior and a change in absorbance of Infrared Radiation (IR) in the FTIR spectrum, as the greater the crosslinking throughout the polymer matrix, the lower the absorbance of IR radiation due to the increased stiffness of the overall macro-molecular structure.

Korayem, Abd-Elrahman↗

Simulation of Dynamic Crushing Behavior of Simulated Carbon/Epoxy Stanchions Using MAT58 and MAT213 in LS-DYNA

Carbon fiber-reinforced polymer (CFRP) composites have shown promise as a material for structures designed to absorb energy in crush-style impact loading. In complementing the lightweight and tailorable characteristics of CFRP structures, the benefits of impact energy absorption are particularly interesting in aerospace vehicles that require excellent crashworthiness performance. However, simulating the behavior of CFRP structures in dynamic, crushing-style impact loading is challenging because of the many damage and failure modes that are essential to capture in the model. For the present investigation, CFRP stanchions were tested using a crash sled experimental test rig. The stanchions were designed by the Composite Materials Handbook-17 (CMH-17) Crashworthiness Working Group for the purpose of comparing experimental crash sled tests to corresponding simulations of the tests. The stanchions are C-channel shaped and represent a geometry common in the interior of aerospace vehicle structures. Explicit simulations in LSDYNA were performed using a well-established composite material model (MAT58) and a next-generation material model (MAT213). Fully integrated shell elements were utilized instead of 3D solid elements to limit computation time. In all models, each of the sixteen plies were represented with individual layers of shell elements with tiebreak contact between each adjacent ply pair to simulate interlaminar fracture. Simulating the crushing of the stanchions occurred in two phases. First, the material models were calibrated using flat specimens that were manufactured with the same layup as the stanchions. While the original goal was calibration of material-related properties, meshdependent behavior was observed in simulations with either material model, and an unstructured mesh was selected to remediate undesirable mesh-dependent failure modes. Additionally, for both the MAT58 and MAT213 models, it was found that either the crush force or the failure mode could be modeled accurately, but no set of parameters could be identified to attain both results in the same model. Once satisfactory calibration was achieved, the same material parameters were applied to the stanchion crush simulations. The stanchion simulations showed that MAT213 more accurately predicted the experimentally determined crush force, and both material models predicted key aspects of the experimentally observed failure modes.

Composite Materials↗

Letter Report: LAW Simulant Development for Cast Stone Screening Test

More than 56 million gallons of radioactive and hazardous waste are stored in 177 underground storage tanks at the U.S. Department of Energy’s (DOE’s) Hanford Site in southeastern Washington State. The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is being constructed to treat the wastes and immobilize them in a glass waste form. The WTP includes a pretreatment facility to separate the wastes into a small volume of high-level waste (HLW) containing most of the radioactivity and a larger volume of low-activity waste (LAW) containing most of the nonradioactive chemicals. The HLW will be converted to glass in the HLW vitrification facility for ultimate disposal at an offsite federal repository. At least a portion (~35%) of the LAW will be converted to glass in the LAW vitrification facility and will be disposed of onsite at the Integrated Disposal Facility (IDF). The pretreatment and HLW vitrification facilities will have the capacity to treat and immobilize the wastes destined for each facility. However, a second facility will be needed for the expected volume of additional LAW requiring immobilization. A cementitious waste form known as Cast Stone is being considered to provide the required additional LAW immobilization capacity. The Cast Stone waste form must be acceptable for disposal in the IDF. The Cast Stone waste form and immobilization process must be tested to demonstrate that the final Cast Stone waste form can comply with waste acceptance criteria for the IDF disposal facility and that the immobilization processes can be controlled to consistently provide an acceptable waste form product. Further, the waste form must be tested to provide the technical basis for understanding the long term performance of the waste form in the IDF disposal environment. These waste form performance data are needed to support risk assessment and performance assessment (PA) analyses of the long-term environmental impact of the waste disposal in the IDF. A testing program was developed in fiscal year (FY) 2012 describing in some detail the work needed to develop and qualify Cast Stone as a waste form for the solidification of Hanford LAW (Westsik et al. 2012). Included within Westsik et al. (2012) is a section on the near-term needs to address Tri-Party Agreement Milestone M-062-40ZZ. The objectives of the testing program to be conducted in FY 2013 and FY 2014 are to: • Determine an acceptable formulation for the LAW Cast Stone waste form. • Evaluate sources of dry materials for preparing the LAW Cast Stone. • Demonstrate the robustness of the Cast Stone waste form for a range of LAW compositions. • Demonstrate the robustness of the formulation for variability in the Cast Stone process. • Provide Cast Stone contaminant release data for PA and risk assessment evaluations. The first step in determining an acceptable formulation for the LAW Cast Stone waste form is to conduct screening tests to examine expected ranges in pretreated LAW composition, waste stream concentrations, dry-materials sources, and mix ratios of waste feed to dry blend. A statistically designed test matrix will be used to evaluate the effects of these key parameters on the properties of the Cast Stone as it is initially prepared and after curing. The second phase of testing will focus on selection of a baseline Cast Stone formulation for LAW and demonstrating that Cast Stone can meet expected waste form requirements for disposal in the IDF. It is expected that this testing will use the results of the screening tests to define a smaller suite of tests to refine the composition of the baseline Cast Stone formulation (e.g. waste concentration, water to dry mix ratio, waste loading).

Russell, Renee L.↗

Carbon fiber composite characterization in adverse thermal environments.

The behavior of carbon fiber aircraft composites was studied in adverse thermal environments. The effects of resin composition and fiber orientation were measured in two test configurations: 102 by 127 millimeter (mm) test coupons were irradiated at approximately 22.5 kW/m{sup 2} to measure thermal response, and 102 by 254 mm test coupons were irradiated at approximately 30.7 kW/m{sup 2} to characterize piloted flame spread in the vertically upward direction. Carbon-fiber composite materials with epoxy and bismaleimide resins, and uni-directional and woven fiber orientations, were tested. Bismaleimide samples produced less smoke, and were more resistant to flame spread, as expected for high temperature thermoset resins with characteristically lower heat release rates. All materials lost approximately 20-25% of their mass regardless of resin type, fiber orientation, or test configuration. Woven fiber composites displayed localized smoke jetting whereas uni-directional composites developed cracks parallel to the fibers from which smoke and flames emanated. Swelling and delamination were observed with volumetric expansion on the order of 100% to 200%. The purpose of this work was to provide validation data for SNL's foundational thermal and combustion modeling capabilities.

36 MATERIALS SCIENCE↗

Environmental Durability Assessment and Development of Subcomponent Test Methods for Advanced Materials in Marine Energy Applications

Marine energy developers are beginning to rely more heavily on advanced composite materials for their load-bearing structures. Understanding how these materials respond and degrade in harsh marine environments is a complex problem. Much research has been performed at smaller laboratory scales to understand the fundamental physical and chemical degradation mechanisms, but little structural testing research has been performed at larger scales to understand how these physical and chemical interactions scale and how they should be accounted for in the design process. The Advanced Materials project is a multilaboratory research collaboration that addresses these issues with the intention of reducing risks and barriers to marine energy developers wanting to adopt advanced composite materials. The National Laboratory of the Rockies has been playing a leading role in developing larger-scale testing infrastructure and test methods to validate complex numerical degradation models and standardize testing procedures to do so. This paper reviews past structural testing activities, how they have grown into current research activities, and how they will continue to evolve to directly address industry needs. This paper covers key research areas - large-scale water absorption and subsequent structural validation testing, qualification of bolted and adhesive connections, and combined submerged fatigue testing at increasing scales. It provides insights into the complex requirements for testing infrastructure and test method development to effectively qualify materials and certify marine energy structures for harsh marine environments. This research program paves the way for better guidance and standardization within the industry when adopting advanced composite materials.

16 TIDAL AND WAVE POWER↗

Methodology for Fast Iterations of Blade Designs Using Thermoplastic Composite Materials: Preprint

Tidal energy is still in the early research and development phases, therefore the ability to quickly manufacture and evaluate prototype blades with new blade designs and materials is critical. This paper investigates using a Stratasys three-dimensional printer to rapidly prototype scale-model turbine blades by printing the blade tooling and using vacuum-assisted resin transfer molding (VARTM) to manufacture blades. This work outlines a methodology for cost effectively designing and manufacturing model-scale tidal turbine blades to be used in testing campaigns, and for evaluating new thermoplastic composite materials for tidal energy applications. Demonstration blades were designed in ANSYS and manufactured using an infusible thermoplastic resin system called Elium(R). The development of scale-model thermoplastic blades enables research into their fatigue performance in realistic conditions at a cost-effective scale, and manufacturing using 3-D printed tooling enables fast and low-cost blade design iterations.

17 WIND ENERGY↗

Environmental Durability Assessment and Development of Subcomponent Test Methods for Advanced Materials in Marine Energy Applications: Preprint

Marine energy developers are beginning to rely more heavily on advanced composite materials for their load bearing structures. Understanding how these materials respond and degrade in harsh marine environments is a complex problem. Much research has been performed at smaller laboratory scales to understand the fundamental physical and chemical degradation mechanisms, but little structural testing research has been performed at larger scales to understand how these physical and chemical interactions scale and how they should be accounted for in the design process. The Advanced Materials project is a multilaboratory research collaboration that has been addressing these issues with the intention of reducing risks and barriers to marine energy developers wanting to adopt advanced composite materials. The National Laboratory of the Rockies has been playing a leading role in developing larger scale testing infrastructure and test methods to validate complex numerical degradation models and standardize testing procedures to do so. This paper provides a review of past structural testing activities and how they have grown into current research activities and will continue to evolve into the future to directly address industry needs. This paper covers key research areas large-scale water absorption and subsequent structural validation testing, qualification of bolted and adhesive connections, and conducting combined submerged fatigue testing at increasing scales. This paper provides insights into the complex requirements for testing infrastructure and test method development to effectively qualify materials and certify marine energy structures for harsh marine environments. This research program paves the way for better guidance and standardization within the industry when adopting advanced composite materials.

16 TIDAL AND WAVE POWER↗

TESTING OF THE SPINTEK ROTARY MICROFILTER USING ACTUAL HANFORD WASTE SAMPLES

The SpinTek rotary microfilter was tested on actual Hanford tank waste. The samples were a composite of archived Tank 241-AN-105 material and a sample representing single-shell tanks (SST). Simulants of the two samples have been used in non-rad test runs at the 222-S laboratory and at Savannah River National Laboratory (SRNL). The results of these studies are compared in this report. Two different nominal pore sizes for the sintered steel rotating disk filter were chosen: 0.5 and 0.1 {micro}m. The results suggest that the 0.5-{micro}m disk is preferable for Hanford tank waste for the following reasons: (1) The filtrate clarity is within the same range (<<4 ntu for both disks); (2) The filtrate flux is in general higher for the 0.5-{micro}m disk; and (3) The 0.1-{micro}m disk showed a higher likelihood of fouling. The filtrate flux of the actual tank samples is generally in the range of 20-30% compared to the equivalent non-rad tests. The AN-105 slurries performed at about twice the filtrate flux of the SST slurries. The reason for this difference has not been identified. Particle size distributions in both cases are very similar; comparison of the chemical composition is not conclusive. The sole hint towards what material was stuck in the filter pore holes came from the analysis of the dried flakes from the surface of the fouled 0.1-{micro}m disk. A cleaning approach developed by SRNL personnel to deal with fouled disks has been found adaptable when using actual Hanford samples. The use of 1 M nitric acid improved the filtrate flux by approximately two times; using the same simulants as in the non-rad test runs showed that the filtrate flux was restored to 1/2 of its original amount.

36 MATERIALS SCIENCE↗

Fatigue-Testing Apparatus for Metal Matrix Composites

Thermal and mechanical load cycling simulated in realistic fatigue tests. Efficient joining of metal matrix composite components to supporting structures is major concern facing users of these materials. Lewis Research Center designed and developed two thermal/mechancical fatigue test facilities, one to test metal matrix composite specimens and another to test compostite/metal attachment bond joints. Thermal/mechanical fatigue facility designed for testing metal matrix composites permits specimen-temperature excursions with controlled heating and loading rates. Second facility designed to test composite/metal attachment bond joints and to permit heating to maximum temperature of 1,400oC (760oC) within 10 min and cooling to 300oF (150oC) within 3 min. Facility has unique capabilities not found in other laboratories.

Westfall, Leonard J.↗

Fuel containment and damage tolerance for large composite primary aircraft structures. Phase 1: Testing

Technical problems associated with fuel containment and damage tolerance of composite material wings for transport aircraft were identified. The major tasks are the following: (1) the preliminary design of damage tolerant wing surface using composite materials; (2) the evaluation of fuel sealing and lightning protection methods for a composite material wing; and (3) an experimental investigation of the damage tolerant characteristics of toughened resin graphite/epoxy materials. The test results, the test techniques, and the test data are presented.

Sandifer, J. P.↗