Search NASA⌕ Search

SEARCH · Search NASA

Results for “data rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

The analysis of ocean optical data

A new oceanographic instrument to measure underwater optical, biological and physical properties simultaneously has been built and used extensively at sea. The Bio-Optical Profiling System (BOPS) was designed for the rapid acquisition of data to accommodate shipboard 'synoptic' sampling strategies, often in conjunction with concurrent aircraft and satellite sensors. The data rates and associated quantity of data from the BOPS are some orders of magnitude larger than those traditionally encountered in optical oceanography. The rapid acquisition of optical data in a wide range of environmental conditions requires new methodologies in ocean optical data analysis.

Smith, R. C.↗
NASA NTRS1987

Data storage systems technology for the Space Station era

The paper presents the results of an internal NASA study to determine if economically feasible data storage solutions are likely to be available to support the ground data transport segment of the Space Station mission. An internal NASA effort to prototype a portion of the required ground data processing system is outlined. It is concluded that the requirements for all ground data storage functions can be met with commercial disk and tape drives assuming conservative technology improvements and that, to meet Space Station data rates with commercial technology, the data will have to be distributed over multiple devices operating in parallel and in a sustained maximum throughput mode.

Dalton, John↗
NASA NTRS1995

Propagation issues in the Globalstar system

The purpose of the Globalstar system is to provide reliable, timely space based telecommunications services for fixed, handheld and mobile user telephones throughout the world. The system supports communication services for voice and data as well as low rate data services such as paging. The Globalstar system can also support user position determination. The purpose of this paper is to provide a brief introduction of the Globalstar system followed by a discussion of the propagation issues in the Globalstar system design.

Prescott, Toby↗
NASA NTRS2003

Measurement of the Earth-Observer-1 Satellite X-Band Phased Array

The recent launch and successful orbiting of the EO-1 Satellite has provided an opportunity to validate the performance of a newly developed X-Band transmit-only phased array aboard the satellite. This paper will compare results of planar near-field testing before and after spacecraft installation as well as on-orbit pattern characterization. The transmit-only array is used as a high data rate antenna for relaying scientific data from the satellite to earth stations. The antenna contains distributed solid-state amplifiers behind each antenna element that cannot be monitored except for radiation pattern measurements. A unique portable planar near-field scanner allows both radiation pattern measurements and also diagnostics of array aperture distribution before and after environmental testing over the ground-integration and prelaunch testing of the satellite. The antenna beam scanning software was confirmed from actual pattern measurements of the scanned beam positions during the spacecraft assembly testing. The scanned radiation patterns on-orbit were compared to the near-field patterns made before launch to confirm the antenna performance. The near-field measurement scanner has provided a versatile testing method for satellite high gain data-link antennas.

Perko, Kenneth↗
NASA NTRS2011

Orion Handling Qualities During ISS Rendezvous and Docking

The Orion spacecraft was designed to rendezvous with multiple vehicles in low earth orbit (LEO) and beyond. To perform the required rendezvous and docking task, Orion must provide enough control authority to perform coarse translational maneuvers while maintaining precision to perform the delicate docking corrections. While Orion has autonomous docking capabilities, it is expected that final approach and docking operations with the International Space Station (ISS) will initially be performed in a manual mode. A series of evaluations was conducted by NASA and Lockheed Martin at the Johnson Space Center to determine the handling qualities (HQ) of the Orion spacecraft during different docking and rendezvous conditions using the Cooper-Harper scale. This paper will address the specifics of the handling qualities methodology, vehicle configuration, scenarios flown, data collection tools, and subject ratings and comments. The initial Orion HQ assessment examined Orion docking to the ISS. This scenario demonstrates the Translational Hand Controller (THC) handling qualities of Orion. During this initial assessment, two different scenarios were evaluated. The first was a nominal docking approach to a stable ISS, with Orion initializing with relative position dispersions and a closing rate of approximately 0.1 ft/sec. The second docking scenario was identical to the first, except the attitude motion of the ISS was modeled to simulate a stress case ( 1 degree deadband per axis and 0.01 deg/sec rate deadband per axis). For both scenarios, subjects started each run on final approach at a docking port-to-port range of 20 ft. Subjects used the THC in pulse mode with cues from the docking camera image, window views, and range and range rate data displayed on the Orion display units. As in the actual design, the attitude of the Orion vehicle was held by the automated flight control system at 0.5 degree deadband per axis. Several error sources were modeled including Reaction Control System (RCS) jet angular and position misalignment, RCS thrust magnitude uncertainty, RCS jet force direction uncertainty due to self plume impingement, and Orion center of mass uncertainty.

Hart, Jeremy J.↗
NASA NTRSDate not supplied

Data Science and the Knowledge Discovery Adventure

This talk will cover the important steps involved in the data science and knowledge discovery process: • Initial fact gathering (interview domain experts, review reports, articles, state-of-the-art) • Identify the problem (prediction, classification, statistical analysis, etc.) • Survey supporting data sources • Understand the data (numerical, categorical, text, sampling rate, data quality issues, etc.) • Selecting relevant features and sources • Acquire the data (set up agreements with the data stewards, APIs to download, etc.) • Merge data sources (temporal, spatial, common key, other ontologies...) • Feature Engineering (non linear domain knowledge or physics-based relationships) • Build data processing pipeline (may need to tap into data stream, develop parallel processing algorithm, federated learning etc.) • Build model and test (tune hyper-parameters, cross validation.) • Analyze/Validate results (do the results make sense. Does it answer the original question). • Deploy/Publish (Monitor and assess benefits)

Data science↗
NASA NTRSDate not supplied

A System to Provide Deterministic Flight Software Operation and Maximize Multicore Processing Performance: The Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) Datapath

A method and design are described for a system that processes multiple data streams, utilizing a multicore asymmetric processing architecture, that eliminates data interrupts to the application processors. The design supports a deterministic environment for flight software in NASA’s Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) project. The SPLICE project develops sensor, algorithm, and compute technologies for Precision Landing and Hazard Avoidance (PL&HA) capabilities. The compute technology for SPLICE is the Descent and Landing Computer (DLC). The DLC hosts several SPLICE algorithms with high computational resource requirements that must be executed in a real-time and deterministic manner. The software runs on a custom Single Board Computer (SBC), with a Xilinx Ultrascale+ Multiprocessor System-on-a-Chip (MPSoC). Input data for the flight software is from a variety of sensors, unique with respect to data rate and packet size. A data path between the SPLICE sensors and algorithms is designed to efficiently deliver this data to the flight software using the MPSoC asymmetric processing cores and Field Programmable Gate Array (FPGA) fabric. This is implemented in a manner that isolates the application processors running the flight software from interrupts associated with the input data. By leveraging real-time processors on the MPSoC, and a structure with the appropriate interfaces in the shared memory on the SBC, the flight software can use the full set of application processors. The available utilization for each processor in this set is also maximized for the SPLICE applications, providing a sufficiently deterministic execution environment without the cost and overhead of a real-time operating system.

heterogeneous processing system↗
NASA NTRS2023

A System to Provide Deterministic Flight Software Operation and Maximize Multicore Processing Performance: The Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) Datapath

A method and design are described for a system that processes multiple data streams, utilizing a multicore asymmetric processing architecture, that eliminates data interrupts to the application processors. The design supports a deterministic environment for flight software in NASA’s Safe and Precise Landing – Integrated Capabilities Evolution (SPLICE) project. The SPLICE project develops sensor, algorithm, and compute technologies for Precision Landing and Hazard Avoidance (PL&HA) capabilities. The compute technology for SPLICE is the Descent and Landing Computer (DLC). The DLC hosts several SPLICE algorithms with high computational resource requirements that must be executed in a real-time and deterministic manner. The software runs on a custom Single Board Computer (SBC), with a Xilinx Ultrascale+ Multiprocessor System-on-a-Chip (MPSoC). Input data for the flight software is from a variety of sensors, unique with respect to data rate and packet size. A data path between the SPLICE sensors and algorithms is designed to efficiently deliver this data to the flight software using the MPSoC asymmetric processing cores and Field Programmable Gate Array (FPGA) fabric. This is implemented in a manner that isolates the application processors running the flight software from interrupts associated with the input data. By leveraging real-time processors on the MPSoC, and a structure with the appropriate interfaces in the shared memory on the SBC, the flight software can use the full set of application processors. The available utilization for each processor in this set is also maximized for the SPLICE applications, providing a sufficiently deterministic execution environment without the cost and overhead of a real-time operating system.

David K. Rutishauser↗
NASA NTRS1982

Benchmark aerodynamic heat-transfer data from the first flight of the Space Shuttle Orbiter

Benchmark entry aerodynamic heat-transfer data were determined from the first flight of the Space Shuttle Orbiter. The convective heating-rate data result from a rigorous mathematical analysis of one-dimensional, transient heat conduction within the orbiter thermal protection system (TPS) and reradiation from its surface during entry. Temperatures measured at the TPS surface during orbiter entry provide a constraint to the analysis. On the vehicle leeside, where heating rate levels are low, corrections are made to the computed convective heating rates to account for solar radiation and cross-radiation between fuselage and wing surfaces. The source of the entry thermal data, the mathematical analysis technique, and the TPS thermal models are discussed. Typical convective heating rate data from the STS-1 mission are presented.

Throckmorton, D. A.↗
NASA NTRS1989

Knowledge-based imaging-sensor fusion system

An imaging system which applies knowledge-based technology to supervise and control both sensor hardware and computation in the imaging system is described. It includes the development of an imaging system breadboard which brings together into one system work that we and others have pursued for LaRC for several years. The goal is to combine Digital Signal Processing (DSP) with Knowledge-Based Processing and also include Neural Net processing. The system is considered a smart camera. Imagine that there is a microgravity experiment on-board Space Station Freedom with a high frame rate, high resolution camera. All the data cannot possibly be acquired from a laboratory on Earth. In fact, only a small fraction of the data will be received. Again, imagine being responsible for some experiments on Mars with the Mars Rover: the data rate is a few kilobits per second for data from several sensors and instruments. Would it not be preferable to have a smart system which would have some human knowledge and yet follow some instructions and attempt to make the best use of the limited bandwidth for transmission. The system concept, current status of the breadboard system and some recent experiments at the Mars-like Amboy Lava Fields in California are discussed.

Westrom, George↗
NASA NTRS2003

On the Use of the Log-Normal Particle Size Distribution to Characterize Global Rain

Although most parameterizations of the drop size distributions (DSD) use the gamma function, there are several advantages to the log-normal form, particularly if we want to characterize the large scale space-time variability of the DSD and rain rate. The advantages of the distribution are twofold: the logarithm of any moment can be expressed as a linear combination of the individual parameters of the distribution; the parameters of the distribution are approximately normally distributed. Since all radar and rainfall-related parameters can be written approximately as a moment of the DSD, the first property allows us to express the logarithm of any radar/rainfall variable as a linear combination of the individual DSD parameters. Another consequence is that any power law relationship between rain rate, reflectivity factor, specific attenuation or water content can be expressed in terms of the covariance matrix of the DSD parameters. The joint-normal property of the DSD parameters has applications to the description of the space-time variation of rainfall in the sense that any radar-rainfall quantity can be specified by the covariance matrix associated with the DSD parameters at two arbitrary space-time points. As such, the parameterization provides a means by which we can use the spaceborne radar-derived DSD parameters to specify in part the covariance matrices globally. However, since satellite observations have coarse temporal sampling, the specification of the temporal covariance must be derived from ancillary measurements and models. Work is presently underway to determine whether the use of instantaneous rain rate data from the TRMM Precipitation Radar can provide good estimates of the spatial correlation in rain rate from data collected in 5(sup 0)x 5(sup 0) x 1 month space-time boxes. To characterize the temporal characteristics of the DSD parameters, disdrometer data are being used from the Wallops Flight Facility site where as many as 4 disdrometers have been used to acquire data over a 2 km path. These data should help quantify the temporal form of the covariance matrix at this site.

Meneghini, Robert↗
NASA NTRS2020

Integration, Test, and On-Orbit Operation of a Ka-band Parabolic Deployable Antenna (KaPDA) for CubeSats

In the past decade, CubeSats have undergone a revolution, moving from universityresearch projects to enabling industry opportunities and government missions. Six yearsago, the Jet Propulsion Laboratory, California Institute of Technology (JPL/Caltech)initiated a research and technology development effort to advance CubeSat communicationcapabilities, with one of the key thrusts being the Ka-band parabolic deployable antenna(KaPDA). This antenna started with the ambitious goal of fitting a 42 dB, 0.5 meter, 35 GHzantenna in a 1.5U canister. At that time, there had been very limited development in the areaof high gain CubeSat antennas which are critical for both high data rate communicationsand remote sensing science. A Ka-band high gain antenna would provide a 10,000 timesincrease in data communication rates over an X-band patch antenna and a 100 timesincrease over state-of-the-art S-band parabolic antennas. This paper discusses the process ofbuilding, integrating, and operating the flight antenna, its final performance and lessonslearned. KaPDA was an enabling technology for RainCube mission, the first Earth ScienceCubeSat to have an active instrument. RainCube was launched in May of 2018, makingKaPDA the second deployable parabolic antenna to fly on a CubeSat and the first of its kindto operate at Ka-band enabling a number of opportunities for high rate, deep space antennacommunications and remote sensing science.

Thomson, Mark W.↗
NASA NTRS1975

An electronic system for measuring thermophysical properties of wind tunnel models

An electronic system is described which measures the surface temperature of a small portion of the surface of the model or sample at high speeds using an infrared radiometer. This data is processed along with heating rate data from the reference heat gauge in a small computer and prints out the desired thermophysical properties, time, surface temperature, and reference heat rate. This system allows fast and accurate property measurements over thirty temperature increments. The technique, the details of the apparatus, the procedure for making these measurements, and the results of some preliminary tests are presented.

Corwin, R. R.↗
NASA NTRS1971

Generation of long time creep data on refractory alloys at elevated temperatures

Ultrahigh vacuum creep tests were performed on tungsten, molybdenum, and tantalum alloys to develop design creep data and to evaluate the influence of liquid lithium exposure on the creep resistance of a tantalum alloy. Test conditions were generally selected to provide 1% creep in 1000 to 10,000 hours, with the test temperatures ranging between 1600 and 2900 F (1144 K and 1866 K). One percent creep life data from a tantalum-base T-111 alloy (Ta-8%W-2%Hf) were analyzed using a station function method to provide an improved parametric representation of the T-111 data. In addition, the minimum creep rate data from an ASTAR 811C alloy (Ta-8%W-1%Re-0.7%Hf0.025%C) were analyzed to determine the stress and temperature dependence of creep rate. Results of this analysis indicated that the activation energy for creep decreased from about 150 Kcal/mole (5130 J/mole) above 2400 F (1589 K) to about 110 Kcal/mole (3760 J/mole) below 2000 F (1361 K). This temperature range corresponds to the range where the creep mechanism changes from grain boundary sliding to intragranular creep.

Sheffler, K. D.↗
NASA NTRSDate not supplied

Large-Scale Space Network Simulator for Performance-Optimized DTNs

High-rate Delay Tolerant Networking (HDTN) is a performance-optimized Delay Tolerant Networking (DTN) implementation that can provide multigigabit per second data rates in disruptive and high-latency space networks. Routing, especially in large-scale space networks, remains challenging due to network topologies that evolve over time. This paper presents a simulation tool that enables HDTN implementation testing at accelerated speeds, which is key for routing in large-scale space networks.

High data-rate Delay Tolerant Networking↗
NASA NTRS2017

From Prototype to Flight: Qualifying a Ka-Band Parabolic Deployable Antenna (KaPDA) for CubeSats

CubeSats have experienced a number of exciting technological advancements in the past several years. However, until recently, there has been very limited development in the area of high gain CubeSat antennas, which are critical for both high data rate communications and radar science. A Ka-band high gain antenna would provide a 10,000 times increase in data communication rates over an X-band patch antenna and a 100 times increase over state-of-the-art S-band parabolic antennas. Because of this, three years ago the Jet Propulsion Laboratory (JPL) initiated a research and technology development effort to advance CubeSat communication capabilities, with one of the key thrusts being the Ka-band parabolic deployable antenna (KaPDA). This antenna started with the ambitious goal of fitting a 42 dB, 0.5 meter, 35 Ghz antenna in a 1.5U (10 cm x 10 cm x 17 cm) canister. This paper discusses the process of taking the antenna from a first prototype to the flight design, which is flying on the RainCube mission, and earth science CubeSat. The prototype antenna was constructed in early 2015, and then upgraded to an engineering model at the end of 2016 to compensate for lessons learned. The flight version is currently under construction, and scheduled to be finished in 2016. KaPDA is the second deployable parabolic antenna to fly on a CubeSat, and the first of its kind to operate at Ka-band enabling a number of opportunities for high rate deep space antenna communications and radar science.

Sauder, Jonathan↗
NASA NTRS2017

From Prototype to Flight: Qualifying a Ka-Band Parabolic Deployable Antenna (KaPDA) for CubeSats

CubeSats have experienced a number of exciting technological advancements in the past several years. However, until recently, there has been very limited development in the area of high gain CubeSat antennas, which are critical for both high data rate communications and radar science. A Ka-band high gain antenna would provide a 10,000 times increase in data communication rates over an X-band patch antenna and a 100 times increase over state-of-the-art S-band parabolic antennas. Because of this, three years ago the Jet Propulsion Laboratory (JPL) initiated a research and technology development effort to advance CubeSat communication capabilities, with one of the key thrusts being the Ka-band parabolic deployable antenna (KaPDA). This antenna started with the ambitious goal of fitting a 42 dB, 0.5 meter, 35 Ghz antenna in a 1.5U canister. This paper discusses the process of taking the antenna from a first prototype to the flight design, how the design successfully met its goals, and lessons learned. A prototype antenna was constructed in early 2015, and then upgraded to an engineering model at the end of 2016. KaPDA will be flying on the RainCube mission, and earth science CubeSat. KaPDA is the second deployable parabolic antenna to fly on a CubeSat, and the first of its kind to operate at Ka-band enabling a number of opportunities for high rate deep space antenna communications and radar science.

Sauder, Jonathan↗