Search NASA⌕ Search

SEARCH · Search NASA

Results for “design pattern”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Acoustic design considerations: Review of rotor acoustic sources

It is not sufficient to optimize a rotor design in terms of a single noise level calculated for a single flight condition and a single measurement location. The various noise sources, their frequency content, amplitude, and directivity as a function of operating condition must be considered. A summary of the frequency ranges, directivity patterns and the most important operational and design parameters for major rotor noise sources is presented. It is difficult to generalize design requirements for rotor noise because the acoustic output varies so widely depending on the noise source, flight condition, measurement location, and frequency range. However, assuming the rotor must lift a fixed nominal payload and operate over a wide range of flight conditions, three general design guidelines can be stated: (1) minimize tip Mach number; (2) minimize blade thickness in the tip region; and (3) minimize gradients in the spanwise lift distribution in the tip region. Constraints on blade thickness, maximum values for hover tip Mach number, advancing tip Mach number and spanwise lift coefficient gradient will be specified during the aerodynamic, dynamic and structural optimization process. The rotor noise sources to be considered include the low frequency loading and thickness noise, and the higher frequency noise due to blade-vortex interactions (BVI). The analyses to be employed will include the comprehensive rotor analysis and design program CAMRAD and the rotor noise prediction program WOPWOP.

Martin, Ruth M.↗
NASA NTRS2009

High Temperature Antenna Measurement System with GSG or GS Contact Probing Capability

Applications that require data transmission at high temperatures are becoming more common due to growing commercial and military needs. Antennas are an indispensable part of these systems and the ability to characterize them at elevated temperatures is quite complicated with little or no information being reported on the subject [1]. This paper describes a measurement system that can characterize planar antennas up 600 C with ground-signal-ground (GSG) or ground-signal (GS) probe contacts. The return loss and radiation patterns of a folded slot antenna (FSA), designed to operate at 5 GHz (no ground plane on back side) and fabricated on an alumina substrate, are presented at room temperature (RT) and 250 C [2]. All measurements were made with Agilent's Precision Network Analyzer (PNA) E8361. The return loss and radiation patterns were also measured on a Styrofoam chuck to illustrate the effect the high temperature measurement system has on the patterns.

Jordan, Jennifer L.↗
NASA NTRS1999

Electrostatic Discharge Effects on Thin Film Resistors

Recently, open circuit failures of individual elements in thin film resistor networks have been attributed to electrostatic discharge (ESD) effects. This paper will discuss the investigation that came to this conclusion and subsequent experimentation intended to characterize design factors that affect the sensitivity of resistor elements to ESD. The ESD testing was performed using the standard human body model simulation. Some of the design elements to be evaluated were: trace width, trace length (and thus width to length ratio), specific resistivity of the trace (ohms per square) and resistance value. However, once the experiments were in progress, it was realized that the ESD sensitivity of most of the complex patterns under evaluation was determined by other design and process factors such as trace shape and termination pad spacing. This paper includes pictorial examples of representative ESD failure sites, and provides some options for designing thin film resistors that are ESD resistant. The risks of ESD damage are assessed and handling precautions suggested.

Sampson, Michael J.↗
NASA NTRS1990

Introducing the VRT gas turbine combustor

An innovative annular combustor configuration is being developed for aircraft and other gas turbine engines. This design has the potential of permitting higher turbine inlet temperatures by reducing the pattern factor and providing a major reduction in NO(x) emission. The design concept is based on a Variable Residence Time (VRT) technique which allows large fuel particles adequate time to completely burn in the circumferentially mixed primary zone. High durability of the combustor is achieved by dual function use of the incoming air. The feasibility of the concept was demonstrated by water analogue tests and 3-D computer modeling. The computer model predicted a 50 percent reduction in pattern factor when compared to a state of the art conventional combustor. The VRT combustor uses only half the number of fuel nozzles of the conventional configuration. The results of the chemical kinetics model require further investigation, as the NO(x) predictions did not correlate with the available experimental and analytical data base.

Melconian, Jerry O.↗
NASA NTRS1990

Introducing the VRT gas turbine combustor

An innovative annular combustor configuration is being developed for aircraft and other gas turbine engines. This design has the potential of permitting higher turbine inlet temperatures by reducing the pattern factor and providing a major reduction in NO(x) emission. The design concept is based on a Variable Residence Time (VRT) technique which allows large fuel particles adequate time to completely burn in the circumferentially mixed primary zone. High durability of the combustor is achieved by dual function use of the incoming air. The feasibility of the concept was demonstrated by water analogue tests and 3-D computer modeling. The computer model predicted a 50 percent reduction in pattern factor when compared to a state of the art conventional combustor. The VRT combustor uses only half the number of fuel nozzles of the conventional configuration. The results of the chemical kinetics model require further investigation, as the NO(x) predictions did not correlate with the available experimental and analytical data base.

Melconian, Jerry O.↗
DOE OSTI2020

Wet Brush Homopolymers as “Smart Solvents” for Rapid, Large Period Block Copolymer Thin Film Self-Assembly

The spontaneous formation of periodic nanopatterns through the self-assembly of block copolymer (BCP) thin films offers an enticing path to engineer functional material properties over large areas, but the prohibitively slow ordering of ultrahigh molecular weight BCPs that generate large pattern periods (>100 nm) severely restricts the design space in which BCPs may be used. Here, we demonstrate that blending lamellae-forming polystyrene-block-poly(methyl methacrylate) diblock copolymers with very low molecular weight polystyrene and poly(methyl methacrylate) homopolymers can reduce by an order-of-magnitude the times required to form ordered large period patterns through solvent vapor annealing. Using in situ grazing-incidence small-angle X-ray scattering and ex situ electron microscopy, we show that the added homopolymer plasticizers act as a “smart solvent”: They increase the mobility of the long BCP chains by amplifying the dilution effect during solvent vapor annealing but segregate to like domains during subsequent thermal annealing to produce high-quality patterns with periods that may exceed 200 nm, which are readily transferred to other materials. The dramatic impact of homopolymer plasticizers may help extend the use of BCPs into new areas, particularly for visible light photonic applications that demand larger period nanopatterns.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Curved grating fabrication techniques for concentric-circle grating, surface-emitting semiconductor lasers

We describe the fabrication and operational characteristics of a novel, surface-emitting semiconductor laser that makes use of a concentric-circle grating to both define its resonant cavity and to provide surface emission. A properly fabricated circular grating causes the laser to operate in radially inward- and outward-going circular waves in the waveguide, thus, introducing the circular symmetry needed for the laser to emit a beam with a circular cross-section. The basic circular-grating-resonator concept can be implemented in any materials system; an AlGaAs/GaAs graded-index, separate confinement heterostructure (GRINSCH), single-quantum-well (SQW) semiconductor laser, grown by molecular beam epitaxy (MBE), was used for the experiments discussed here. Each concentric-circle grating was fabricated on the surface of the AlGaAs/GaAs semiconductor laser. The circular pattern was first defined by electron-beam (e-beam) lithography in a layer of polymethylmethacrylate (PMMA) and subsequently etched into the semiconductor surface using chemically-assisted (chlorine) ion-beam etching (CAIBE). We consider issues that affect the fabrication and quality of the gratings. These issues include grating design requirements, data representation of the grating pattern, and e-beam scan method. We provide examples of how these techniques can be implemented and their impact on the resulting laser performance. A comparison is made of the results obtained using two fundamentally different electron-beam writing systems. Circular gratings with period lambda = 0.25 microns and overall diameters ranging from 80 microns to 500 microns were fabricated. We also report our successful demonstration of an optically pumped, concentric-circle grating, semiconductor laser that emits a beam with a far-field divergence angle that is less than one degree. The emission spectrum is quite narrow (less than 0.1 nm) and is centered at wavelength lambda = 0.8175 microns.

Jordan, Rebecca H.↗
NASA NTRS1996

Optimal Design of Grid-Stiffened Composite Panels Using Global and Local Buckling Analysis

A design strategy for optimal design of composite grid-stiffened panels subjected to global and local buckling constraints is developed using a discrete optimizer. An improved smeared stiffener theory is used for the global buckling analysis. Local buckling of skin segments is assessed using a Rayleigh-Ritz method that accounts for material anisotropy and transverse shear flexibility. The local buckling of stiffener segments is also assessed. Design variables are the axial and transverse stiffener spacing, stiffener height and thickness, skin laminate, and stiffening configuration. The design optimization process is adapted to identify the lightest-weight stiffening configuration and pattern for grid stiffened composite panels given the overall panel dimensions, design in-plane loads, material properties, and boundary conditions of the grid-stiffened panel.

Ambur, Damodar R.↗
NASA NTRS2004

Fluidic Chevrons for Jet Noise Reduction

Chevron mixing devices are used to reduce noise from commercial separate-flow turbofan engines. Mechanical chevron serrations at the nozzle trailing edge generate axial vorticity that enhances jet plume mixing and consequently reduces far-field noise. Fluidic chevrons generated with air injected near the nozzle trailing edge create a vorticity field similar to that of the mechanical chevrons and allow more flexibility in controlling acoustic and thrust performance than a passive mechanical design. In addition, the design of such a system has the future potential for actively controlling jet noise by pulsing or otherwise optimally distributing the injected air. Scale model jet noise experiments have been performed in the NASA Langley Low Speed Aeroacoustic Wind Tunnel to investigate the fluidic chevron concept. Acoustic data from different fluidic chevron designs are shown. Varying degrees of noise reduction are achieved depending on the injection pattern and injection flow conditions. CFD results were used to select design concepts that displayed axial vorticity growth similar to that associated with mechanical chevrons and qualitatively describe the air injection flow and the impact on acoustic performance.

Kinzie, Kevin↗
NASA NTRS1991

Amplitude and phase-shaping effects in beamwaveguides

Results are presented of an investigation on improvements in a geometrical optics (GO) design of a beam-waveguide antenna for operation at multiple frequency bands. Improvements might be possible by changing the design of the lower-frequency input pattern to the beam waveguide. The effects of amplitude and phase shaping the input pattern have been studied with an aperture diffraction model. Accurate vector near-field computations were made rapidly with a spherical wave expansion of the input and scattered fields. Numerical results indicate that for aperture sizes of less than 30 wavelengths, there is insufficient control on defocusing due to amplitude and phase shaping. Design tradeoffs on spillover loss and defocusing are possible by changing the amplitude and phase distribution of the input wavefront for larger size apertures.

Rengarajan, Sembiam R.↗
DOE OSTI2018

IL-Net: Using Expert Knowledge to Guide the Design of Furcated Neural Networks

Deep neural networks (DNN) excel at extracting patterns. Through representation learning and automated feature engineering on large datasets, such models have been highly successful in computer vision and natural language applications. Designing optimal network architectures from a principled or rational approach however has been less than successful, with the best successful approaches utilizing an additional machine learning algorithm to tune the network hyperparameters. However, in many technical fields, there exist established domain knowledge and understanding about the subject matter. In this work, we develop a novel furcated neural network architecture that utilizes domain knowledge as high-level design principles of the network. We demonstrate proof-of-concept by developing IL-Net, a furcated network for predicting the properties of ionic liquids, which is a class of complex multi-chemicals entities. Compared to existing state-of-the-art approaches, we show that furcated networks can improve model accuracy by approximately 20-35%, without using additional labeled data. Lastly, we distill two key design principles for furcated networks that can be adapted to other domains.

Sakloth, Khushmeen↗
NASA NTRS2018

En Route Detect and Avoid Well Clear in Terminal Area Landing Pattern

A fast time simulation was conducted to test the detect and avoid Well Clear definition designed for en route use when an unmanned aircraft (UA) is approaching the landing pattern of the terminal area. Measures focused on were loss of well clear and alerts intended to help the pilot avoid loss of well clear. Data indicated warning-level alerts will occur outside the typical Class D airspace which may prevent the UA from normal operations in the terminal airspace. Other aircraft on 45o entry could result in “nuisance” alerts which may also prevent the UA from normal operations in the terminal airspace. However, eliminating horizontal proximity (τmod) has the potential to increase “nuisance” alerts on the 45o entry and downwind legs. Overall, this suggests that a more stringent definition of Well Clear may be advisable in the landing pattern of the terminal area.

Trujillo, Anna C.↗
NASA NTRS1989

Development of a class of antennas for space-based Navstar GPS applications

This paper describes the performance of several unique antenna/ground plane configurations currently being developed for the TOPEX satellite and which may also be used for improved ground station operation. These antennas are designed with the objective of achieving nearly hemispherical coverage with sharp pattern cutoff above the horizon together with uniform phase response over the entire coverage area. The most promising of these designs is a uniform choke ring approximately 2 lambda in diameter. The ground planes, when used with the Dorne-Margolin C246 antenna element, produce smooth pattern cutoff of the order of 0.25 dB per deg over 135 deg, excellent LCP rejection, and rms phase deviation of 5-5.7 deg. Other ground plane designs, including larger choke ring structures, slotted ground planes, and the use of absorber material, proved much less effective.

Tranquilla, J. M.↗
DOE OSTI2019

CFD-Guided Combustion System Optimization of a Gasoline Range Fuel in a Heavy-Duty Compression Ignition Engine Using Automatic Piston Geometry Generation and a Supercomputer

A computational fluid dynamics (CFD) guided combustion system optimization was conducted for a heavy-duty diesel engine running with a gasoline fuel that has a research octane number (RON) of 80. The goal was to optimize the gasoline compression ignition (GCI) combustion recipe (piston bowl geometry, injector spray pattern, in-cylinder swirl motion, and thermal boundary conditions) for improved fuel efficiency while maintaining engine-out NO x within a 1-1.5 g/kW-hr window. The numerical model was developed using the multi-dimensional CFD software CONVERGE. A two-stage design of experiments (DoE) approach was employed with the first stage focusing on the piston bowl shape optimization and the second addressing refinement of the combustion recipe. For optimizing the piston bowl geometry, a software tool, CAESES, was utilized to automatically perturb key bowl design parameters. This led to the generation of 256 combustion chamber designs evaluated at several engine operating conditions. The second DoE campaign was conducted to optimize injector spray patterns, fuel injection strategies and in-cylinder swirl motion for the best performing piston bowl designs from the first DoE campaign. This comprehensive optimization study was performed on a supercomputer, Mira, to accelerate the development of an optimized fuel-efficiency focused design. Compared to the production combustion system in the baseline engine, the new combustion recipe from this study showed significantly improved closed-cycle fuel efficiency across key engine operating points while meeting the engine-out NO x targets. Optimized piston bowl designs and injector spray patterns were predicted to provide enhanced in-cylinder air utilization and more rapid mixing-controlled combustion, thereby leading to a fuel efficiency improvement. In addition, shifting the engine thermal boundary conditions toward leaner operation was also key to the improved fuel efficiency.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1991

A semi-automated process for the production of custom-made shoes

A more efficient, cost-effective and timely way of designing and manufacturing custom footware is needed. A potential solution to this problem lies in the use of computer-aided design and manufacturing (CAD/CAM) techniques in the production of custom shoes. A prototype computer-based system was developed, and the system is primarily a software entity which directs and controls a 3-D scanner, a lathe or milling machine, and a pattern-cutting machine to produce the shoe last and the components to be assembled into a shoe. The steps in this process are: (1) scan the surface of the foot to obtain a 3-D image; (2) thin the foot surface data and create a tiled wire model of the foot; (3) interactively modify the wire model of the foot to produce a model of the shoe last; (4) machine the last; (5) scan the surface of the last and verify that it correctly represents the last model; (6) design cutting patterns for shoe uppers; (7) cut uppers; (8) machine an inverse mold for the shoe innersole/sole combination; (9) mold the innersole/sole; and (10) assemble the shoe. For all its capabilities, this system still requires the direction and assistance of skilled operators, and shoemakers to assemble the shoes. Currently, the system is running on a SUN3/260 workstation with TAAC application accelerator. The software elements of the system are written in either Fortran or C and run under a UNIX operator system.

Farmer, Franklin H.↗
NASA NTRS2015

Modeling of an Adjustable Beam Solid State Light Project

This proposal is for the development of a computational model of a prototype variable beam light source using optical modeling software, Zemax Optics Studio. The variable beam light source would be designed to generate flood, spot, and directional beam patterns, while maintaining the same average power usage. The optical model would demonstrate the possibility of such a light source and its ability to address several issues: commonality of design, human task variability, and light source design process improvements. An adaptive lighting solution that utilizes the same electronics footprint and power constraints while addressing variability of lighting needed for the range of exploration tasks can save costs and allow for the development of common avionics for lighting controls.

Clark, Toni↗
NASA NTRS1988

Time-Zone-Pattern Satellite Broadcasting Antenna

Direct-broadcast satellite antenna designs provide contoured beams to match four time zones in 48 contiguous states and spot beams for Alaska, Hawaii, and Puerto Rico presented in 29-page report. Includes descriptions of procedures used to arrive at optimized designs. Arrangements, amplitudes, and phases of antenna feeds presented in tables. Gain contours shown graphically. Additional tables of performance data given for cities in service area of Eastern satellite.

Galindo, Victor↗
NASA NTRS2005

Reconfigurable Antennas for High Data Rate Multi-beam Communication Systems

High-speed (2-100 Mb/sec) wireless data communication - whether land- or satellite-based - faces a major challenge: high error rates caused by interference and unpredictable environments. A planar antenna system that can be reconfigured to respond to changing conditions has the potential to dramatically improve data throughput and system reliability. Moreover, new planar antenna designs that reduce array size, weight, and cost can have a significant impact on terrestrial and satellite communication system performance. This research developed new individually-reconfigurable planar antenna array elements that can be adjusted to provide multiple beams while providing increased scan angles and higher aperture efficiency than traditional diffraction-limited arrays. These new elements are microstrip spiral antennas with specialized tuning mechanisms that provide adjustable radiation patterns. We anticipate that these new elements can be used in both large and small arrays for inter-satellite communication as well as tracking of multiple mobile surface-based units. Our work has developed both theoretical descriptions as well as experimental prototypes of the antennas in both single element and array embodiments. The technical summary of the results of this work is divided into six sections: A. Cavity model for analysis and design of pattern reconfigurable antennas; B. Performance of antenna in array configurations for broadside and endfire operation; C. Performance of antenna in array configurations for beam scanning operation; D. Simulation of antennas in infinite phased arrays; E. Demonstration of antenna with commercially-available RF MEMS switches; F. Design of antenna MEMS switch combinations for direct simultaneous fabrication.

Bernhard, Jennifer T.↗