SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The objective of this analysis is to process Lincoln Laboratory Doppler radar data obtained during FLOWS testing at Huntsville, Alabama, in the summer of 1986, to characterize windshear events. The processing includes plotting velocity and F-factor profiles, histogram analysis to summarize statistics, and correlation analysis to demonstrate any correlation between different data fields.
Technique for visualization of three-dimensional flow uses tiny tracer bubbles of hydrogen and oxygen made by electrolysis of water. Strobe-light photography used to capture flow patterns, yielding permanent record that is measured to obtain velocities of particles. Used to measure simulated mixing turbulence in proposed gas-turbine combustor and also used in other water-table flow tests.
The program for integration and testing the ACTS is outlined. Special attention is given to the test objectives, the ACTS automated ground equipment, the ACTS spacecraft test flow, and a near field antenna measurements system. The program is scheduled to take approximately 21 months and be completed during the 4th quarter of 1991. The launch of the ACTS spacecraft is scheduled for May 1992 from Cape Kennedy, as part of a Space Shuttle mission.
The time-dependent, three-dimensional incompressible Navier-Stokes equations are presently solved in generalized coordinate systems by means of a fractional-step method whose primitive variable formulation uses as dependent variables, in place of the Cartesian components of the velocity: (1) pressure (defined at the center of the computational cell), and (2) volume fluxes across the faces of the cells. The momentum equations are solved by means of an approximate factorization method. A novel 'ZEBRA' scheme incorporating four-color ordering efficiently solves the Poisson equation. Illustrative two- and three-dimensional laminar flow test cases are computed and evaluated relative to extant numerical and experimental results, and good agreement is obtained.
Shuttle-C provides NASA with a heavy-lift cargo capability that is a low-cost derivative of the current Space Shuttle. This system can deliver 80,000 to 140,000 pounds of payload to low earth orbit within 4 years of authority to proceed. Shuttle-C will share th existing Shuttle launch facilities at Kennedy Space Center (KSC). The Shuttle-C vehicle incorporates an auxiliary propulsion system (APS) which provides separation from the external tank (ET), orbit circularization, on-orbit attitude hold, and deorbit capability. The APS is derived from the Shuttle orbiter aft reaction control system (ARCS) and orbital maneuvering system (OMS) with the objective of achieving minimum life cycle cost for this expendable vehicle. The resulting APS system will be described, its plan for a minimum-cost flight certification utilizing a cold-flow test program explained, and low-cost evolution by component design modification and part substitution presented.
A concept that offers an alternate method for thrust vector control of liquid or solid propellant rockets is the use of a solid body or probe that is inserted on demand through the wall of the rocket nozzle. This Probe Thrust Vector Control (PTVC) concept is an alternative to that of a gimbaled nozzle or a Liquid Injection Thrust Vector control system. The viability of the PTVC concept can be assessed either experimentally and/or with the use of CFD. A purely experimental assessment is time consuming and expensive, whereas a CFD assessment is time- and cost-effective. Two key requirements of the concept are PTVC vectoring performance and active cooling requirements for the probe to maintain its thermal and structural integrity. The objective of the work reported here is presentation of experimental subscale cold flow tests and comparison of these tests with CFD predictions and the response time of the PTVC system.
A model to analyze the unstready multidimensional turbulent flow in the head-end, star slot section of a solid rocket motor during the ignition transient is developed. The present paper examines the fluid dynamic aspects of the starting transient. A finite-difference solution of the unsteady, compressible, full Navier-Stokes equations, together with a two-equation k-epsilon turbulence model, is obtained utilizing the MacCormack explicit, predictor-corrector technique. Computed results for the flow in the slot are compared with experimental data obtained in cold flow tests of a scaled model of the Space Shuttle SRM head-end, star grain section. The agreement between the calculated flowfield and existing experimental data is very good.
It is established that Computational Fluid Dynamics (CFD) code validation is an integral part of all flow testing. Specific attention is given to the development of new methods/instruments to obtain time varying 3-D data. Additionally, a discussion concerning wind tunnels and small test facilities is presented. All results and data are presented in viewgraph form.
The present steady and unsteady quasi-1D internal supersonic flowfield calculations employs a novel viscous-inviscid interaction technique directly coupling and simultaneously solving the inviscid and viscous equations. The coupled system is numerically solved using a two-stage Runge-Kutta scheme with first-order one-sided spatial differencing. Simple supersonic internal flow test cases are computed to demonstrate the capabilities of the computational procedure.
An investigation is being conducted to determine the feasibility of studying aileron buzz by means of the wing-flow method. Two semispan models which had an aspect ratio of 6 and a taper ratio of 2 with quarter-chord half-span mass-balanced ailerons have been used. One had an NACA 23012 airfoil section and the second, an NACA 65-212 airfoil section. The ailerons on both models were subject to buzz over a small range of Mach number near 0.9. Data obtained by wing-flow testing agreed reasonably well with full-scale flight results.
An investigation was conducted to determine the effect of a coolant solution of 25 percent ethyl alcohol, 25 percent methyl alcohol, and 50 percent water by volume and maximum-economy spark advance on knock-limited performance and fuel economy of a large air-cooled cylinder. The knock-limited performance of the cylinder at engine speeds of 2100 and 2500 rpm was determined for coolant-fuel ratios of 0.0, 0.2, and 0.4. The effect of water-alcohol injection on fuel economy was determined in constant charge-air flow tests. The tests were conducted at a spark advance of 20 deg B.T.C. and maximum-economy spark advance.
A low-speed investigation was made in the 6- by 6-foot curved-flow test section of the Langley stability tunnel to determine the effects of change in profile and aspect ratio on the pitching derivatives of triangular wings. The effects of aspect ratio on the pitching derivatives of a series of modified triangular wings, obtained by cutting various portions from the tips of a basic triangle, also were determined. Values of the damping-in-pitch parameter (Cmq) obtained for the triangular and modified triangular wings were one-fifth to one-tenth as large as the value expected for a typical airplane.
The basic ideas of a new method for treating the problem of the airfoil are presented, and a review is given of the problems thus far computed for incompressible and supersonic flows. Test results are reported for the airfoil of circular plan form and the results are shown to agree well with the theory. As a supplement, a theory based on the older methods is presented for the rectangular of small aspect ratio.
A project has been initiated at the Marshall Space Flight Center to determine if preburner inter- or intra-element mixture ratio maldistributions are the cause of temperature variations in the Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP) turbine inlet region. Temperature nonuniformity may contribute to the many problems experienced in this region. The project will involve high pressure cold-flow testing and Computational Fluid Dynamics (CFD) modeling.
During the high-Mach-number, high-altitude portion of the first entry of the Shuttle Orbiter, the vehicle exhibited a nose-up pitching moment relative to preflight prediction of approximately Delta Cm = 0.03. This trim anomaly has been postulated to be due to compressibility, viscous, and/or real-gas (lowered specific heat ratio gamma) effects on basic body pitching moment, body-flap effectiveness, or both. In order to assess the relative contribution of each of these effects, an experimental study was undertaken to examine the effects of Mach number, Reynolds number, and ratio of specific heats. Complementary computational solutions were obtained for wind-tunnel and flight conditions. The primary cause of the anomaly was determined to be lower pressures on the aft windward surface of the Orbiter than deduced from hypersonic wind-tunnel tests with ideal- or near-ideal-gas test flow. The lower pressure levels are a result of the lowering of the flowfield gamma due to high-temperature effects. This phenomenon was accurately simulated in a hypersonic wind tunnel using a heavy gas, which provided a lower, gamma, and was correctly predicted by Navier-Stokes computations using nonequilibrium chemistry.
Work focussed on a large number of preliminary studies of supersonic combustion in a simple combustion duct - thrust nozzle combination, investigating effects of Mach number, equivalence ratio, combustor divergence, fuel injecting angle and other parameters with an influence on the combustion process. This phase lasted for some three or four years, during which strongest emphasis was placed on responding to the request for preliminary experimental information on high enthalpy effects, to support the technology maturation activities of the NASP program. As the need for preliminary data became less urgent, it was possible to conduct more systematic studies of high enthalpy combustion phenomena, and to initiate other projects aimed at improving the facilities and instrumentation used for studying scramjet phenomena at high enthalpies. The combustion studies were particularly directed towards hypersonic combustion, and to the effects of injecting fuel along the combustion chamber wall. A substantial effort was directed towards a study of the effect of scale on the supersonic combustion process. The influence of wave phenomena (both compression waves and expansion waves) on the realization of thrust from a supersonic combustion process was also investigated. The effect of chemical kinetics was looked into, particularly as it affected the composition of the test flow provided by a ground facility. The effect of injection of the fuel through wall orifices was compared with injection from a strut spanning the stream, and the effect of heating the fuel prior to injection was investigated. Studies of fuel-air mixing by shock impingement were also done, as well as mass spectrometer surveys of a combustion wake. The use of hypersonic nozzles with an expansion tube was investigated. A new method was developed for measuring the forces acting of a model in less than one millisecond. Also included in this report are listings of published journal papers and conference presentations.
Measurement of drag have been made in a shock tunnel on a simple integrated vehicle engine combination for hypersonic cruise with hydrogen scramjet propulsion. The test flow Mach number was 6.4, and the velocity was 2.45 kms(exp -1). Zero Drag, which is the necessary condition for cruise, was achieved as the equivalence ratio approached one. It was found that an analysis using established aerodynamic concept was adequate for predicting drag in the case of no combustion. When combustion occurred results of direct connect experiments provided was qualitative guide to the measured levels of drag, and indicated that thrust nozzle combustion was taking place. An heuristic analysis is used to point to the important effect this may have on propulsive lift.
An applied research program was conducted to determine the properties of flat sheets of propellants formed by directing jets of liquid tangentially against concave, cylindrical deflector surfaces. The dimensions and spatial orientation of the resultant sheets were found to depend only on the orifice diameter and deflector geometry for three propellant simulants of widely-varying physical properties, over the range of injection velocities encountered in liquid rocket engines. Correlating equations, suitable for use in injector design, are presented for free-sheet width and spreading angle. Distribution of mass and velocity across the free-flowing sheets is also reported. Conditions were discovered under which true sheets do not form, or at best malformed or pulsating sheets result. An envelope of geometrical constraints for deflector design is tentatively defined in order to avoid these undesirable operating regions. The results of the present cold-flow tests are compared with firing test data for impinging-sheet injectors and combustion performance is related to single sheet behavior.