Search NASA⌕ Search

SEARCH · Search NASA

Results for “geometry optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

High regularity of Z-DNA revealed by ultra high-resolution crystal structure at 0.55;#8201;Å

The crystal structure of a Z-DNA hexamer duplex d(CGCGCG){sub 2} determined at ultra high resolution of 0.55 {angstrom} and refined without restraints, displays a high degree of regularity and rigidity in its stereochemistry, in contrast to the more flexible B-DNA duplexes. The estimations of standard uncertainties of all individually refined parameters, obtained by full-matrix least-squares optimization, are comparable with values that are typical for small-molecule crystallography. The Z-DNA model generated with ultra high-resolution diffraction data can be used to revise the stereochemical restraints applied in lower resolution refinements. Detailed comparisons of the stereochemical library values with the present accurate Z-DNA parameters, shows in general a good agreement, but also reveals significant discrepancies in the description of guanine-sugar valence angles and in the geometry of the phosphate groups.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A review of breast tomosynthesis. Part I. The image acquisition process

Mammography is a very well-established imaging modality for the early detection and diagnosis of breast cancer. However, since the introduction of digital imaging to the realm of radiology, more advanced, and especially tomographic imaging methods have been made possible. One of these methods, breast tomosynthesis, has finally been introduced to the clinic for routine everyday use, with potential to in the future replace mammography for screening for breast cancer. In this two part paper, the extensive research performed during the development of breast tomosynthesis is reviewed, with a focus on the research addressing the medical physics aspects of this imaging modality. This first paper will review the research performed on the issues relevant to the image acquisition process, including system design, optimization of geometry and technique, x-ray scatter, and radiation dose. The companion to this paper will review all other aspects of breast tomosynthesis imaging, including the reconstruction process.

60 APPLIED LIFE SCIENCES↗

Calibrating mix models for NIF tuning

Mixing may playa role in early 'tuning' implosions at the National Ignition Facility (NIF), intended for optimizing target geometry and laser operating parameters prior to the first ignition shots. Turbulent transport models allow mixing to be represented in integrated capsule-plus-hohlraum simulations, so that its effects can be predicted. Such models typically have many adjustable coefficients, so it is important to calibrate the coefficients systematically, whether by comparison to experiments, theory, or detailed higher fidelity simulations. We have begun by comparing to results from high-resolution 2D multimode simulations of a NIF Rev3 CH(Ge) ignition capsule, using the time-varying angle-averaged radial profiles of ion species composition as the calibration reference. 1D implosion simulations are performed with either of two turbulence models, and the models are calibrated so that the 1D composition profiles roughly match the 2D reference profIles at a sequence of five times near the end of the implosion. Details of the reference profiles, however, such as non-monotonicity resulting from structures in the flow, cannot be represented by these models. Parameter searches, besides identifying optimal sets of model coefficients, also show model sensitivity to parameter variations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

MO-F-CAMPUS-I-04: Characterization of Fan Beam Coded Aperture Coherent Scatter Spectral Imaging Methods for Differentiation of Normal and Neoplastic Breast Structures

Purpose: This study intends to characterize the spectral and spatial resolution limits of various fan beam geometries for differentiation of normal and neoplastic breast structures via coded aperture coherent scatter spectral imaging techniques. In previous studies, pencil beam raster scanning methods using coherent scatter computed tomography and selected volume tomography have yielded excellent results for tumor discrimination. However, these methods don’t readily conform to clinical constraints; primarily prolonged scan times and excessive dose to the patient. Here, we refine a fan beam coded aperture coherent scatter imaging system to characterize the tradeoffs between dose, scan time and image quality for breast tumor discrimination. Methods: An X-ray tube (125kVp, 400mAs) illuminated the sample with collimated fan beams of varying widths (3mm to 25mm). Scatter data was collected via two linear-array energy-sensitive detectors oriented parallel and perpendicular to the beam plane. An iterative reconstruction algorithm yields images of the sample’s spatial distribution and respective spectral data for each location. To model in-vivo tumor analysis, surgically resected breast tumor samples were used in conjunction with lard, which has a form factor comparable to adipose (fat). Results: Quantitative analysis with current setup geometry indicated optimal performance for beams up to 10mm wide, with wider beams producing poorer spatial resolution. Scan time for a fixed volume was reduced by a factor of 6 when scanned with a 10mm fan beam compared to a 1.5mm pencil beam. Conclusion: The study demonstrates the utility of fan beam coherent scatter spectral imaging for differentiation of normal and neoplastic breast tissues has successfully reduced dose and scan times whilst sufficiently preserving spectral and spatial resolution. Future work to alter the coded aperture and detector geometries could potentially allow the use of even wider fans, thereby making coded aperture coherent scatter imaging a clinically viable method for breast cancer detection. United States Department of Homeland Security; Duke University Medical Center - Department of Radiology; Carl E Ravin Advanced Imaging Laboratories; Duke University Medical Physics Graduate Program.

60 APPLIED LIFE SCIENCES↗

Modeling of light intensification by conical pits within multilayer coatings

Removal of laser-induced damage sites provides a possible mitigation pathway to improve damage resistance of coated multilayer dielectric mirrors. In an effort to determine the optimal mitigation geometry which will not generate secondary damage precursors, the electric field distribution within the coating layers for a variety of mitigation shapes under different irradiation angles has been estimated using the finite difference time domain (FDTD) method. The coating consists of twenty-four alternating layers of hafnia and silica with a quarter-wave reflector design. A conical geometrical shape with different cone angles is investigated in the present study. Beam incident angles range from 0{sup o} to 60{sup o} at 5{sup o} increments. We find that light intensification (square of electric field, |E|{sup 2}) within the multilayers depends strongly on the beam incident direction and the cone angle. By comparing the field intensification for each cone angle under all angles of incidence, we find that a 30{sup o} conical pit generates the least field intensification within the multilayer film. Our results suggest that conical pits with shallow cone angles ({le} 30{sup o}) can be used as potential optimal mitigation structures.

42 ENGINEERING↗

Impact of Linker Strain and Flexibility in the Design of a Fragment-Based Inhibitor

The linking together of molecular fragments that bind to adjacent sites on an enzyme can lead to high-affinity inhibitors. Ideally, this strategy would use linkers that do not perturb the optimal binding geometries of the fragments and do not have excessive conformational flexibility that would increase the entropic penalty of binding. In reality, these aims are seldom realized owing to limitations in linker chemistry. Here we systematically explore the energetic and structural effects of rigid and flexible linkers on the binding of a fragment-based inhibitor of human uracil DNA glycosylase. Analysis of the free energies of binding in combination with cocrystal structures shows that the flexibility and strain of a given linker can have a substantial impact on binding affinity even when the binding fragments are optimally positioned. Such effects are not apparent from inspection of structures and underscore the importance of linker optimization in fragment-based drug discovery efforts.

59 BASIC BIOLOGICAL SCIENCES↗

Inter-ion coulomb interactions in a magneto-optical trap ion source

We have investigated the role played by inter-ion Coulomb interactions in a magneto-optical trap ion source (MOTIS). Using a Monte Carlo simulation accounting for all pair-wise ion-ion Coulomb interactions in the source, we have calculated the broadening of the transverse spatial and velocity distributions as well as the increase in emittance over a range of beam currents and extraction electric fields. Using a {sup 7}Li MOTIS, we have experimentally studied the broadening of the spatial distribution as a function of total beam current and extraction electric field by measuring the fraction of the beam current that passes through a 20 {mu}m diameter aperture. The Monte Carlo simulations agree well with the experimental results, indicating that such simulations capture the essential physics of the source. Our results show that while Coulomb interactions can cause a significant increase in emittance in some situations, it is possible to keep the effects to an acceptable level by suitable choice of extraction field and beam current. These considerations are essential to the process of optimizing MOTIS geometry and operating conditions for use in high-resolution focused ion beam applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

In situ ligand restraints from quantum-mechanical methods

In macromolecular crystallographic structure refinement, ligands present challenges for the generation of geometric restraints due to their large chemical variability, their possible novel nature and their specific interaction with the binding pocket of the protein. Quantum-mechanical approaches are useful for providing accurate ligand geometries, but can be plagued by the number of minima in flexible molecules. In an effort to avoid these issues, the Quantum Mechanical Restraints (QMR) procedure optimizes the ligand geometry in situ , thus accounting for the influence of the macromolecule on the local energy minima of the ligand. The optimized ligand geometry is used to generate target values for geometric restraints during the crystallographic refinement. As demonstrated using a sample of >2330 ligand instances in >1700 protein–ligand models, QMR restraints generally result in lower deviations from the target stereochemistry compared with conventionally generated restraints. In particular, the QMR approach provides accurate torsion restraints for ligands and other entities.

59 BASIC BIOLOGICAL SCIENCES↗

Liquid-Cooled Aluminum Silicon Carbide Heat Sinks for Reliable Power Electronics Packages

With recent advances in the state-of-the-art of power electronic devices, packaging has become one of the critical factors limiting the performance and durability of power electronics. To this end, this study investigates the feasibility of a novel integrated package assembly, which consists of copper circuit layer on an aluminum nitride (AlN) dielectric layer that is bonded to an aluminum silicon carbide (AlSiC) substrate. The entire assembly possesses a low coefficient of thermal expansion (CTE) mismatch which aids in the thermal cycling reliability of the structure. The new assembly can serve as a replacement for the conventionally used direct bonded copper (DBC) - Cu base plate - Al heat sink assembly. While improvements in thermal cycling stability of more than a factor of 18 has been demonstrated, the use of AlSiC can result in increased thermal resistance when compared to thick copper heat spreaders. To address this issue, we demonstrate that the integration of single phase liquid cooling in the AlSiC layer can result in improved thermal performance, matching that of copper heat spreading layers. This is aided by the use of heat transfer enhancement features built into the AlSiC layer. It is found that, for a given pumping power and through analytical optimization of geometries, either microchannels, pin fins and jets can be designed to yield a heat transfer coefficients of up to 65000 W m -2 K -1 , which can result in competitive device temperatures as Cu-baseplate designs, but with added reliability.

30 DIRECT ENERGY CONVERSION↗

Warm gas TVC design study

A warm gas thrust vector control system was studied to optimize the injection geometry for a specific engine configuration, and an injection valve was designed capable of meeting the base line requirements. To optimize injection geometry, studies were made to determine the performance effects of varying injection location, angle, port size, and port configuration. Having minimized the injection flow rate required, a warm gas valve was designed to handle the required flow. A direct drive hydraulic servovalve capable of operating with highly contaminated hydraulic fluid was designed. The valve is sized to flow 15 gpm at 3000 psia and the direct drive feature is capable of applying a spool force of 200 pounds. The baseline requirements are the development of 6 deg of thrust vector control utilizing 2000 F (total temperature) gas for 180 seconds on a 1.37 million pound thrust engine burning LOX and RP-1 at a chamber pressure of 250 psia with a 155 inch long conical nozzle having a 68 inch diameter throat and a 153 inch diameter exit.

Moorhead, S. B., Jr.↗

Coupled Reactor Multiphysics and Mass Scalability Assessment for Crewed Megawatt-Class NEP System Architectures

Nuclear Electric Propulsion (NEP) is an in-space propulsion technology capable of enabling opposition and conjunction class crewed Mars missions. NEP subsystems include the reactor for heat generation, a power conversion system (PCS), power management and distribution, electric propulsion system, and heat rejection system. Specific mass, or α (kg/kWe), is a key performance parameter (KPP) of the propulsion system which is directly scalable with the performance and mass predictions for each individual component. To inform technology maturation planning activities, full system and component level parametric modeling is ongoing to explore the design trade space and illustrate the effect of subsystem design choices on the system KPPs. In this study, scaling of high-assay, low-enriched uranium reactor designs is assessed through coupled reactor physics and thermal hydraulics analyses. Scaling analyses evaluate the impact of system performance parameters (power level, interface temperatures) on mass for direct gas cooled, pumped liquid metal, and passively-cooled heat pipe reactor concepts. Each concept requires specific geometries, fluids, and power conversion interface conditions (temperature, pressure, flow rate) to meet desired performance and mass. The reactor assembly includes the active core (fuel, moderator, cladding, working fluid), axial and radial neutron reflectors, control drums, structural support / pressure vessel, and external radiation shielding. Each of these components are parametrically sized based on performance parameters for a megawatt-class power cycle. Results of this scaling analysis increase NEP propulsion system modeling fidelity and ultimately aim to support concept down-selection along with related technology development planning. The reactor and shield α are a function of several PCS and heat rejection system design choices, and reactor scaling with these parameters must be considered to enable an informed decision on an optimal reactor geometry and working fluid combination.

Nuclear Electric Propulsion↗

Evaluation of Thermal Neutron Scattering Cross Section of Uranium Silicide with Ab Initio Lattice Dynamics

Uranium silicide (U 3 Si 2 ) is a candidate material for the high-density nuclear fuel in commercial light water reactors [1], [2]. Its higher uranium density, 11.3 g-U/cm3, compared to that of uranium dioxide (UO 2 ), 9.7 g-U/cm3, can improve the performance of a nuclear reactor while using low enriched uranium (LEU) and diversify the choice of cladding materials [1]–[3]. It also has a higher thermal conductivity than UO 2 , which can reduce the thermal stress on the material caused by a temperature gradient across the fuel pellet and provide a larger margin for some postulated accidents [1], [2], [4]. Furthermore, compared to U3Si, another high-density fuel candidate, it has better resistance to in-pile swelling due to less irradiation-induced rapid amorphization [1], [3]. Corresponding to its importance in nuclear engineering, many previous studies have reported the properties of U3Si2. Experiments showed that U 3 Si 2 is a paramagnetic (PM) metal, where a slight linear increase in magnetic susceptibility was measured with increasing temperature [5], [6]. In addition, thermodynamic quantities such as thermal expansion coefficient, heat capacity, and thermal conductivity were experimentally determined over a wide temperature range [1], [7], [8]. In several computational studies, ab initio atomistic simulations based on density functional theory (DFT) were performed to calculate various properties including elastic constants, electronic density of states (DOS), and phonon dispersion curves [9]–[12]. Nevertheless, thermal neutron scattering cross sections, which are critical to the prediction of the parameters in reactor physics that are ultimately related to reactor criticality, have not yet been evaluated for U3Si2. The scattering cross section can be calculated from the phonon DOS, or the energy spectrum of lattice vibrations, of the crystalline system [13], [14]. However, there is also no experimental data available for the phonon DOS of U 3 Si 2 . While some computational studies reported the phonon DOS and/or dispersion curves from ab initio simulations [9]–[12], the accuracy cannot be guaranteed because it is unclear whether the spin-polarization behavior of PM U 3 Si 2 was properly described. In the present study, the thermal neutron scattering cross section for U 3 Si 2 is evaluated for the first time by calculating the phonon DOS for U3Si2 from ab initio lattice dynamics (AILD) simulations based on DFT. First, U 3 Si 2 is modeled based on the experimental structure, and AILD simulations are performed on the modeled U3Si2 to optimize the structure. Next, AILD simulations are performed for supercells with atomic displacement to calculate Hellmann-Feynman forces. Based on the calculated forces, partial phonon DOSs for U and Si are obtained, and the thermal neutron scattering law (TSL) for U 3 Si 2 is finally evaluated. To verify the accuracy of the calculations in the present study, the calculation results are compared with experimental data on the structure and heat capacity of U3Si2 [1], [7], [8], [15].

Geometry Optimization↗

Design and Calibration of Autonomous Coherent Doppler Lidar for Space Missions

Developed a new algorithm for the simulation of three dimensional homogeneous turbulent velocity fields. For typical atmospheric conditions it is impossible to produce a simulated velocity field that simultaneously satisfy a given spatial correlation and the corresponding spatial spectrum because of spectral aliasing. The new algorithms produce a turbulent velocity field which has accurate spatial correlations which is required for performance predictions from space-based systems. Developed a new algorithm for extracting the spatial statistics of the atmospheric velocity field using coherent Doppler lidar. The performance of the algorithm was compared with past methods and the new algorithm produces useful results for space-based data, which was not possible before. Developed new methods for verification of the errors in ground-based and space-based Doppler lidar wind measurements. These new methods do not require independent in situ data. This is an important issue for the verification of space-based Doppler lidar measurements of the global wind field. The performance of the new algorithm was compared with past results for both space-based and ground-based operation. The new algorithm has the best performance and is the only algorithm that performed satisfactory for spacebased operation. The performance of coherent Doppler lidar for a space missions with various scanning geometries was determined using computer simulation which contained the effects of random instrumental velocity errors, wind shear, wind variability along the range-gate and from shot-to-shot, and random variations in atmospheric aerosol backscatter over the measurement volume. The bias in the velocity estimates was small and the accuracy in the is typically less than 0.5 m/s for high signal conditions. For a large number of shot per velocity estimate, the threshold signal level for acceptable estimates is proportional to the number of shots to the minus one half power. This agrees with previous results determined for ground-based measurements. The use of multi-element optical detectors for autonomous operation of coherent Doppler lidar was shown to be a very promising technique. Optimal detector geometries were determined by computer simulation of performance: for ground-based testing with a fixed calibration target and for space-based operation using the random surface returns. The effects of refractive turbulence on ground-based calibration of coherent Doppler lidar was determined by computer simulations and compared with theoretical predictions. New techniques were required to correctly predict performance for the focused beam geometry commonly used for verification of space-based operation. An improved velocity estimator was evaluated for space-based applications were signal shot measurements are used to produce vector wind measurements. This permits more accurate measurements when the signal level is not known a priori or not available from multiple shot measurements. The average Doppler lidar signal spectrum including the effects of velocity turbulence was derived and calculated. This permits new estimation algorithms for turbulence based on spectral estimates. In situ atmospheric measurements were conducted and analyzed using an instrumented kite-platform. This work helps provide the required in situ data for verification of Doppler lidar velocity statistics.

Frehlich, Rod G.↗

Investigation of an Ultrafast Harmonic Resonant RF Kicker

An Energy Recovery Linac (ERL) based multi-turn electron Circulator Cooler Ring (CCR) is envisaged in the proposed Jefferson Lab Electron Ion Collider (JLEIC) to cool the ion bunches with high energy (55 MeV), high current (1.5 A), high repetition frequency (476.3 MHz), high quality magnetized electron bunches. A critical component in this scheme is a pair of ultrafast kickers for the exchange of electron bunches between the ERL and the CCR. The ultrafast kicker should operate with the rise and fall time in less than 2.1 ns, at the repetition rate of ~10s MHz, and should be able to run continuously during the whole period of cooling. These -and-fall time being combined together, are well beyond the state-of-art of traditional pulsed power supplies and magnet kickers. To solve this technical challenge, an alternative method is to generate this high repetition rate, fast rise-and-fall time short pulse continuous waveform by summing several finite number of (co)sine waves at harmonic frequencies of the kicking repetition frequency, and these harmonic modes can be generated by the Quarter Wave Resonater (QWR) based multifrequency cavities. Assuming the recirculator factor is 10, 10 harmonic modes (from 47.63 MHz to 476.3 MHz) with proper amplitudes and phases, plus a DC offset are combined together, a continuous short pulse waveform with the rise-and-fall time in less than 2.1 ns, repetition rate of 47.63 MHz waveform can be generated. With the compact and matured technology of QWR cavities, the total cost of both hardware development and operation can be reduced to a modest level. Focuse on the technical scheme, three main topics will be discussed in this thesis: the synthetization of the kicking pulse, the design and optimization of the deflecting QWR multi-integer harmonic frequency resonator and the fabrication and bench measurements of a half scale copper prototype. In the kicking pulse synthetization part, we begin with the Fourier Series expansion of an ideal square pulse, and get a Flat-Top waveform which will give a uniform kick over the bunch length of the kicked electron bunches, thus the transverse emittance of these kicked electron bunches can be maintained. By using two identical kickers with the betatron phase advance of 180 degree or its odd multiples, the residual kick voltage wave slopes at the unkicked bunch position will be totally cancelled out. Flat-Top waveform combined with two kicker scheme, the transverse emittance of the cooling electron bunches will be conserved during the whole injection, recirculation, and ejection processes. In the cavity design part, firstly, the cavity geometry is optimized to get high transverse shunt impedance thus less than 100 W of RF losses on the cavity wall can be achieved for all these 10 harmonic modes. To support all these 10 harmonic modes, group of four QWRs are adopted with the mode distribution of 5:3:1:1. In the multi-frequency cavities such as the five-mode-cavity and the three-mode-cavity, tunings are required to achieve the design frequencies for each mode. Slight segments of taper design on the inner conductor help to get the frequencies to be exactly on the odd harmonic modes. Stub tuners equal to the number of resonant modes are inserted to the outer conductor wall to compensate the frequency shifts due manufacturing errors and other perturbations during the operation such as the change of the cavity temperature. Single loop couple is designed for all harmonic modes in each cavity. By adjusting its loop size, position and rotation, it is possible to get the fundamental mode critical coupled and other higher harmonic modes slightly over coupled. A broadband circulator will be considered for absorbing the reflected power. Finally in this part, multipole field components due to the asymmetric cylindrical structure around the beam axis of the cavity as well as the beam-induced higher order mode (HOM) issues will be analyzed and discussed in this thesis. A half-scale copper prototype cavity (resonant frequencies from 95.26 MHz to 857.34 MHz) was fabricated to validate the electromagnetic characteristics. With this half scale prototype, the tuning processes of multiple harmonic frequencies, unloaded quality factor measurements of each mode, and bead-pull measurements are performed. The bench measurement results matched well with the simulation results, which have validated our cavity design and construction methods. Finally, a simple mode combining experiment with five separate signal generators was performed on this prototype cavity and the desired fast rise/fall time (1.2 ns), high repetition rate (95.26 MHz) waveform was captured, which finally proved our design of this ultrafast harmonic kicker.

43 PARTICLE ACCELERATORS↗

Conceptual design of ELM control coils for the TCABR tokamak

An upgrade of the Tokamak à Chauffage Alfvén Brésilien (TCABR) is being designed to make it capable of creating a well controlled environment where the impact of resonant magnetic perturbation (RMP) fields on edge localised modes can be addressed over a wide range of (i) plasma shapes, (ii) divertor configurations, (iii) RMP coil geometries and (iv) perturbed magnetic field spectra. To this end, a unique set of in-vessel RMP coils is being designed and, in this work, their conceptual design is presented. This unique set of coils is composed of three toroidal arrays of coils on the low field side and three toroidal arrays of coils on the high field side. Each of these six toroidal arrays is composed of 18 coils thus allowing for the creation of RMP fields with toroidal mode numbers n ≤ 9 and with increased control of the poloidal mode number spectrum. To study dynamical effects of RMP fields of different toroidal mode numbers, all rotating simultaneously with different velocities, each of the 108 RMP coils will be powered independently by power supplies that can provide voltages of up to 4 kV and electric currents of up to 2 kA, with frequencies varying continuously from 0Hz up to 10kHz. A set of physical criteria were used to determine the optimal coil geometry and their respective number of turns to reduce the coil currents and voltages during operation with alternate current. Further, the conceptual design was carried out using both the vacuum approach (no plasma response) and the single-fluid response approach, which accounts for the response of a linear, single-fluid, visco-resistive plasma calculated using the M3D-C 1 code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Photonic crystal enhanced light-trapping in thin film solar cells

We utilize photonic crystals to simulate enhanced light-trapping in a-Si:H thin film solar cells. A one dimensional photonic crystal or distributed Bragg reflector with alternating dielectric layers acts as low loss backreflector. A two dimensional photonic crystal between the absorber layer and the Bragg reflector diffracts light at oblique angles within the absorber. The photonic crystal geometry is optimized to obtain maximum absorption. The photonic crystal provides lossless diffraction of photons, increasing the photon path length within the absorber layer. The simulation predicts significantly enhanced photon harvesting between 600 and 775?nm below the band edge, and an absorption increase by more than a factor of 10 near the band edge. The optical path length ratio can exceed the classical limit predicted for randomly roughened scattering surfaces at most wavelengths near the band edge. The optical modeling is performed with a rigorous scattering matrix approach where Maxwell's equations are solved in Fourier space.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Matching Crystal Structures Atom-to-Atom

Finding an optimal match between two different crystal structures underpins many important materials science problems, including describing solid-solid phase transitions and developing models for interface and grain boundary structures. Here, we formulate the matching of crystals as an optimization problem where the goal is to find the alignment and the atom-to-atom map that minimize a given cost function such as the Euclidean distance between the atoms. We construct an algorithm that directly solves this problem for large finite portions of the crystals and retrieves the periodicity of the match subsequently. We demonstrate its capacity to describe transformation pathways between known polymorphs and to reproduce experimentally realized structures of semi-coherent interfaces. Additionally, from our findings, we define a rigorous metric for measuring distances between crystal structures that can be used to properly quantify their geometric (Euclidean) closeness.

36 MATERIALS SCIENCE↗

Mechanism of Thermal Reversal of the (Fulvalene)tetracarbonyldiruthenium Photoisomerization: Toward Molecular Solar-Thermal Energy Storage

In the currently intensifying quest to harness solar energy for the powering of our planet, most efforts are centered around photoinduced generic charge separation, such as in photovoltaics, water splitting, other small molecule activation, and biologically inspired photosynthetic systems. In contrast, direct collection of heat from sunlight has received much less diversified attention, its bulk devoted to the development of concentrating solar thermal power plants, in which mirrors are used to focus the sun beam on an appropriate heat transfer material. An attractive alternative strategy would be to trap solar energy in the form of chemical bonds, ideally through the photoconversion of a suitable molecule to a higher energy isomer, which, in turn, would release the stored energy by thermal reversal. Such a system would encompass the essential elements of a rechargeable heat battery, with its inherent advantages of storage, transportability, and use on demand. The underlying concept has been explored extensively with organic molecules (such as the norbornadiene-quadricyclane cycle), often in the context of developing photoswitches. On the other hand, organometallic complexes have remained relatively obscure in this capacity, despite a number of advantages, including expanded structural tunability and generally favorable electronic absorption regimes. A highly promising organometallic system is the previously reported, robust photo-thermal fulvalene (Fv) diruthenium couple 1 {l_reversible} 2 (Scheme 1). However, although reversible and moderately efficient, lack of a full, detailed atom-scale understanding of its key conversion and storage mechanisms have limited our ability to improve on its performance or identify optimal variants, such as substituents on the Fv, ligands other than CO, and alternative metals. Here we present a theoretical investigation, in conjunction with corroborating experiments, of the mechanism for the heat releasing step of 2 {yields} 1 and its Fe (4) and Os (6) relatives. The results of the combined study has enabled a rigorous interpretation of earlier and new experimental measurements and paint a surprising picture. First-principles calculations were employed based on spin unrestricted density functional theory (DFT) with a non-empirical gradient corrected exchange-correlation functional. Ultrasoft pseudopotentials were used to describe the valence-core interactions of electrons, including scalar relativistic effects of the core. Wavefunctions and charge densities were expanded in plane waves with kinetic energies up to 25 and 200 Rydberg, respectively. Reaction pathways were delineated with the string method, as implemented within the Car-Parrinello approach. This method allows for the efficient determination of the minimum energy path (MEP) of atomistic transitions and thus also saddle points (transition states, TSs), which are the energy maxima along the MEP. All geometries were optimized until all forces on the atoms were less than 0.02 eV/{angstrom}. The calculated structures of 1 and 2 were in good agreement with their experimental counterparts.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗