Search NASA⌕ Search

SEARCH · Search NASA

Results for “geometry optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

High-Efficiency Low-Cost Solar Receiver for Use Ina a Supercritical CO 2 Recompression Cycle

This project has performed solar receiver designs for two supercritical carbon dioxide (sCO 2 ) power cycles. The first half of the program focused on a nominally 2 MWe power cycle, with a receiver designed for test at the Sandia Solar Thermal Test Facility. This led to an economical cavity-type receiver. The second half of the program focused on a 10 MWe power cycle, incorporating a surround open receiver. Rigorous component life and performance testing was performed in support of both receiver designs. The receiver performance objectives are set to conform to the US DOE goals of 6¢/kWh by 2020 . Key findings for both cavity-type and direct open receiver are highlighted below: A tube-based absorber design is impractical at specified temperatures, pressures and heat fluxes for the application; a plate-fin architecture however has been shown to meet performance and life targets; the $148/kW th cost of the design is significantly less than the SunShot cost target with a margin of 30%; the proposed receiver design is scalable, and may be applied to both modular cavity-type installations as well as large utility-scale open receiver installations; the design may be integrated with thermal storage systems, allowing for continuous high-efficiency electrical production during off-sun hours; costs associated with a direct sCO 2 receiver for a sCO 2 Brayton power cycle are comparable to those of a typical molten salt receiver; lifetimes in excess of the 90,000 hour goal are achievable with an optimal cell geometry; the thermal performance of the Brayton receiver is significantly higher than the industry standard, and enables at least a 30% efficiency improvement over the performance of the baseline steam-Rankine boiler/cycle system; brayton’s patent-pending quartz tube window provides a greater than five-percent efficiency benefit to the receiver by reducing both convection and radiation losses.

14 SOLAR ENERGY↗

Comparison of Failure Mechanisms Due to Shock Propagation in Forged, Layered, and Additive Manufactured Titanium

This chapter for the Stewardship Science Academic Programs Annual Report describes a project focused on characterizing the shock propagation and failure mechanisms in forged, layered, and additive manufactured (AM) materials. The AM process fabricates a part layer by layer, which provides opportunities to tailor geometry and optimize structural performance in addition to minimizing the amount of material waste for odd shaped parts.

36 MATERIALS SCIENCE↗

Dissolution of Additively Manufactured Mo Disks and Structures for Accelerator Based Production of Mo-99

The press-and-sinter approach for production of Mo targets has been successfully tested and demonstrated. The main advantage of this process is that it uses readily available technology and tools that have been tuned for production of various metal and metal oxide targets. However, certain target design specifications, such as dimensional accuracy of the diameter and thickness of the disks, are required for proper fit into a target holder and therefore place strict tolerances on sintered Mo disks intended for accelerator production. Furthermore, having a target composed of multiple disks poses certain challenges for post-irradiation processing, where there is a potential for spillage of individual disks during the manipulation for dissolution inside a processing hot cell. Additive manufacturing (AM), also referred to as 3D printing, provides capabilities to design and build a single-piece Mo target that provides the opportunity for better geometry for optimized production of Mo-99, improved cooling capability, and safer post-irradiation handling. A drawback of AM Mo structures is roughness of finished surfaces, which could reduce the effectiveness of gas cooling systems. Process development for AM Mo structures using selective laser melting is described in work by Gibson and Lowden. For post-irradiation processing, it is important to look at the dissolution behavior of AM Mo structures in comparison to readily dissolved press-and-sinter Mo targets. The dissolution behavior of press-and-sinter targets has been well documented in our previous reports. In this report, we discuss results of dissolution experiments conducted with AM Mo disks and structures (provided by Oak Ridge National Laboratory [ORNL]) in 50% hydrogen peroxide (H 2 O 2 ).

36 MATERIALS SCIENCE↗

Monitoring for Additive Manufacturing Technologies: Report on Progress, Achievements, and Limitations of Monitoring Techniques

The Transformational Challenge Reactor (TCR) program is leveraging additive manufacturing (AM) technologies to produce multiple nuclear components to be assembled into a fully functional microreactor core. AM was selected as the main manufacturing technology of choice for TCR because it has the potential to disrupt the nuclear industry on two fronts: (1) it enables the manufacturing of very complex geometries with optimized and tailored material properties for the intended use of the component, opening up new options for reactor designs, and (2) it allows for a better understanding of the manufacturing process through real-time in situ monitoring, data analytics, and artificial intelligence that can lead to a streamlined qualification and certification process. Within TCR, the development and deployment of a digital platform aims at addressing the latter opportunity. As part of this effort, the collection of pedigree data sets is vital, should these data be generated before, during, or after the manufacturing process. This report focuses on the collection of manufacturing process data using systems instrumentation and monitoring. It presents an inventory of the various monitoring modalities installed on the manufacturing systems by the machine manufacturer or specifically designed by our team to fill information gaps. It also provides details on other relevant data streams available and leverageable to evaluate the manufacturing process on all classes of AM systems investigated during the first year of this program. Through examples, the report gives an overview of the data collected and presents a path forward for the digital platform.

42 ENGINEERING↗

Viability of Data Analytics to Ascertain Component Performance for Additive Manufacturing

The Transformational Challenge Reactor (TCR) program is leveraging additive manufacturing (AM) technologies to produce multiple nuclear components to be assembled into a fully functional microreactor core. AM was selected as the main manufacturing technology for TCR because it has the potential to disrupt the nuclear industry on two fronts: (1) it enables the manufacturing of very complex geometries with optimized and tailored material properties for the intended use of the component, opening up new options for reactor designs, and (2) it allows for a better understanding of the manufacturing process through real-time in situ monitoring, data analytics, and artificial intelligence, which can lead to a streamlined qualification and certification process. Within TCR, the development and deployment of a digital platform aims at addressing the latter opportunity. As part of this effort, the collection of pedigree datasets is vital, should these data be generated before, during or after the manufacturing process. This report focuses on the development of data analytics tools enabling qualitative assessment of the manufacturing processes to automate the identification of flaws in in situ monitoring imagery and to correlate those flaws to the resulting mechanical testing data. Through examples, the report gives an overview of the data collected and presents a path forward for the digital platform.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Numerical Modeling & Optimization of the iProTech Pitching Inertial Pump (PIP) Wave Energy Converter (WEC) (CRADA Final Report)

This project represents a continuation of the collaboration between iProTech and NLR to simulate, optimize and design the iProTech Pitching Inertial Pump (PIP) device. The objectives of this TEAMER project are twofold: 1. Refining the physical characteristics of the existing iProTech PIP WEC-Sim model to enhance the model’s fidelity and include controllable components. Key model enhancements target the inclusion of Coulomb friction, the introduction of a controllable bypass valve, and the replacement of traditional check valves with advanced motorized ones. 2. Exploring traditional and advanced control algorithms. From traditional methods like latching control to cutting-edge reinforcement learning (RL) algorithms, the goal is to ensure the PIP device's adaptability and optimal performance across a range of ocean conditions. NLR is tasked with augmenting the WEC-Sim model and implementing the control algorithms, culminating in performance comparison analyses. iProTech will update their existing 3D models, advise on model improvements, and determine crucial system metrics. WEC-Sim, developed in MATLAB/SIMULINK with Simscape Multibody, is the main piece of software that will be used in this project. Coupled with the MATLAB RL Toolbox, it offers a robust platform for in-depth simulation and optimization of the iProTech PIP device. Building on previous work to explore the PIP design space and optimize its geometry, mass distribution, center of gravity and other key parameters, this project aims to refine iProTech’s existing numerical models and develop effective control algorithms that can seamlessly integrate into their future hardware testing campaigns.

16 TIDAL AND WAVE POWER↗

Optimizing Hammermill Performance Through Screen Selection and Hammer Design

Background: Mechanical preprocessing, which includes particle size reduction and mechanical separation, is one of the primary operations in the feedstock supply system for a lignocellulosic biorefinery. It is the means by which raw biomass from the field or forest is mechanically transformed into an on-spec feedstock with characteristics better suited for the fuel conversion process. Results: This work provides a general overview of the objectives and methodologies of mechanical preprocessing and then presents experimental results illustrating (1) improved size reduction via optimization of hammer mill configuration, (2) improved size reduction via pneumatic-assisted hammer milling, and (3) improved control of particle size and particle size distribution through proper selection of grinder process parameters. Conclusion: Optimal grinder configuration for maximal process throughput and efficiency is strongly dependent on feedstock type and properties, such moisture content. Tests conducted using a HG200 hammer grinder indicate that increasing the tip speed, optimizing hammer geometry, and adding pneumatic assist can increase grinder throughput as much as 400%.

09 BIOMASS FUELS↗

CFD and X-ray Analysis of Gaseous Direct Injection from an Outward Opening Injector

Using natural gas in an internal combustion engine (ICE) is emerging as a promising way to improve thermal efficiency and reduce exhaust emissions. In the development of such engine platforms, computational fluid dynamics (CFD) plays a fundamental role in the optimization of geometries and operating parameters. One of the most relevant issues in the simulation of direct injection (DI) gaseous processes is the accurate prediction of the gas jet evolution. The simulation of the injection process for a gaseous fuel does not require complex modeling, nevertheless properly describing high-pressure gas jets remains a challenging task. At the exit of the nozzle, the injected gas is under-expanded, the flow becomes supersonic and shocks occur due to compressibility effects. These phenomena lead to challenging computational requirements resulting from high grid resolution and low computational time-steps. In this paper, the simulation of gaseous injection from an outward opening injector was carried out with the commercial CFD software CONVERGE. Argon was injected into a quiescent chamber filled with Nitrogen. Two free-jet cases with injection pressure of 15 and 10 bar, and ambient pressure of 1 and 2 bar respectively, were tested. For the 15 bar injection pressure and 1 bar ambient pressure, a jet impinging on a barrier case was performed as well. The numerical results were validated against experimental mass measurements using X-ray radiography. The results, presented in terms of 2D maps and transverse sections of equivalent path length of argon, showed good agreement between modeling and experiments in terms of jet penetration, shape and gas mass distribution. These emphasized the significant impact of mesh size on the results for the simulation of this type of injector. Due to the small geometrical dimensions a fine mesh is required in order to deliver an accurate description of the mixture formation. Numerical results were discussed with a particular emphasis on the application to engine simulations, where a trade-off between accuracy and computational time is a necessity.

Bartolucci, Lorenzo↗

Development of the Generation 3 Particle Pilot Plant Falling Particle Receiver

A falling particle receiver (FPR) has been designed to integrate with the G3P3-USA pilot plant currently being constructed at the National Solar Thermal Test Facility (NSTTF) at Sandia National Laboratories. This receiver integrates several innovative design features including a converging tunnel (SNOUT), an optimized cavity geometry, and a multistage “catch-and-release” trough. Details about the integration of these features and the final G3P3-USA FPR design and construction are described. Ray-tracing models of the FPR utilizing the NSTTF heliostat field are developed leveraging previous modeling efforts using SolTrace. Models demonstrate that at least 1.5 MWth of incident radiative energy can be provided to the FPR on a clear day throughout a typical year in Albuquerque, NM. Spillage fluxes around the periphery of the aperture are within acceptable bounds for the majority of the year. Intercept factors are computed for each utilized heliostat at the Vernal equinox to provide guidance to heliostat operators during operation of the system.

Mills, Brantley↗

Array of virtual Frisch-grid CZT detectors with common cathode readout and pulse-height correction

We present our new results from testing 15-mm-long virtual Frisch-grid CdZnTe detectors with a common-cathode readout for correcting pulse-height distortions. The array employs parallelepiped-shaped CdZnTe (CZT) detectors of a large geometrical aspect ratio, with two planar contacts on the top and bottom surfaces (anode and cathode) and an additional shielding electrode on the crystal's sides to create the virtual Frisch-grid effect. We optimized the geometry of the device and improved its spectral response. We found that reducing to 5 mm the length of the shielding electrode placed next to the anode had no adverse effects on the device's performance. At the same time, this allowed corrections for electron loss by reading the cathode signals to obtain depth information.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Advanced Electric Submersible Pump Design Tool for Geothermal Applications

Electrical Submersible Pumps (ESPs) present higher efficiency, larger production rate, and can be operated in deeper wells than the other geothermal artificial lifting systems. Enhanced Geothermal Systems (EGS) applications recommend lifting 300 C geothermal water at 80kg/s flow rate in a maximum 10-5/8-inch diameter wellbore to improve the cost-effectiveness. In this paper, an advanced ESP design tool comprising a 1D theoretical model and a 3D CFD analysis has been developed to design ESPs for geothermal applications. Design of Experiments was also performed to optimize the geometry and performance. The designed mixed-flow type centrifugal impeller and diffuser exhibit high efficiency and head rise under simulated EGS conditions. The design tool has been validated by comparing the prediction to experimental data of an existing ESP product.

15 GEOTHERMAL ENERGY↗

Additive Manufactured Materials Studies

The production of additively manufactured (AM) materials, is a growing technology that potentially offers more cost effective ways to produce metallic components for various uses. Mechanical properties of some AM metals have been studied, but more work is needed to better understand their dynamic properties as a function of orientation. Due to the melting and reheating of molten metal during fabrication, these materials tend to have internal porosity and slightly different microstructures along the weldments and normal to the weldments that may cause the materials to behave differently than their forged counterparts. The AM process builds up a part layer by layer, which provides opportunities to tailor geometry and optimize structural performance in addition to minimizing the amount of material waste for oddly shaped parts, thereby reducing cost. These advanced materials hold great promise for revolutionizing design, fabrication, and assembly of engineered components and could be used for many NNSA-specific applications including armoring complex elements of nuclear weapons, and customized diagnostic components in subcritical experiments. We have conducted materials studies in collaboration with the University of Nevada, Las Vegas (UNLV) as well as Los Alamos National Laboratory (LANL) under our Site-Directed Research and Development program and the Nevada Science Initiative. We are currently placing emphasis on quantifying how dynamic properties are affected by directionality and porosity of the material. A study of dynamic failure events in forged, layered, and additive manufactured (AM) titanium alloy subject to hypervelocity impact was conducted in collaboration with UNLV. Experiments were conducted using a two stage light-gas gun, 0.22-caliber Lexan projectiles, and different types of titanium target plates. A four-channel Photonic Doppler Velocimetry (PDV) system was used to study the free surface velocities to provide an understanding of the different failure mechanisms in these materials. The experimental measurements were used to validate computational simulations, which describe the behavior of these materials under shock. It was determined that AM, forged titanium, and multi-layered stacks produce similar velocity profiles during the early stage of impact, with the AM targets exhibiting spall at lower velocities and the multi-layered stacks exhibiting vibrations between plates. Simulations of solid and layered forged materials provide a good match to experimental data.

36 MATERIALS SCIENCE↗

High count rate thermal neutron detectors and electronics

Improved, high count rate thermal neutron counters and electronics enabling new, higher measurement capabilities are disclosed. Next generation 3He and 10B tubes may include an electronics package capable of operating at higher count rates and in higher gamma fields and providing more efficient use of 3He gas. Conventional detector systems may also be upgraded, providing a possible solution to measure spent nuclear fuel with high neutron efficiency previously not possible in 235U fission counter systems. Switching the number of tubes per amplifier allows use of the measured nuclear material for a calibration standard for dead time correction, increasing accuracy of neutron measurements systems. An optimized detector geometry and advanced electronics with double pulse filtering and a dual channel readout may be provided. A bipolar shaper may improve dead time, provide efficient detector use, reduce double pulsing, facilitate high count rate measurements, and allow remote threshold setting.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

νBDX: a Coherent Elastic Neutrino Nucleus Scattering (CEνNS) experiment at Jefferson Lab

Particle physics is an ever-changing field seeking to explain phenomena that lie at the limits of our current knowledge. Among discovered and hypothesized interactions, Coherent Elastic Neutrino-Nucleus Scattering (CE?NS) stands out as a fascinating and elusive phenomenon, offering a unique window into the nature of neutrinos and their interactions with matter. CE?NS, a process predicted by the Standard Model, represents one of the subtle ways in which neutrinos can interact with atomic nuclei. Unlike other neutrinonucleus interactions, CE?NS occurs coherently, meaning that the entire nucleus collectively responds to the neutrino-mediated weak force, resulting in small energy transfers to the nucleus as a whole. The extremely rare nature of CE?NS events presents a formidable challenge to experimenters seeking to detect and study these interactions. Recent advances in detector technologies and the implementation of large-scale experiments, such as coherent neutrino scattering experiments at research facilities around the world, have opened up new avenues for exploring this elusive phenomenon. These experiments aim not only to observe CE?NS directly but also to extract valuable information on neutrino properties, nuclear structure, and potential deviations from the Standard Model. This thesis aims to study the feasibility of an experiment to study CE?NS at The Thomas Jefferson National Accelerator Facility, Newport News, VA, USA. This would be an experiment that exploits the production of neutrinos by an electron beam dumped on a thick target (the beam dump). The large quantity of neutrinos produced and their energy profile are well suited to the purpose of studying the CE?NS. In my thesis, I will start from previous studies on CE?NS and from theoretical considerations regarding the process, then quantify the expected events for a hypothetical experiment and possible backgrounds through simulations aimed at optimizing the geometry of the future detector. I will also show some tests on selected detector components that will be part of a first prototype.

Grazzi, Stefano↗