Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Automated Probabilistic Finite Element Model Calibration Tool Based on Uncertainty Quantification and Machine Learning

Qualification and certification of safety critical parts is a hurdle to the adoption of metallic additively manufactured components for aerospace vehicle applications. Challenges include variability in part properties due to inconsistent defect distribution and microstructure. Understanding of the process through finite element modeling (FEM), and process control through in-situ monitoring, may result in significant improvements; however, solutions useful to manufacturers will require large volumes of data and automated data utilization. Toward this end, a generalizable automated FEM calibration paradigm is developed. This paradigm leverages existing and novel tools from machine learning and uncertainty quantification to enable the automatic calibration of FEMs without requiring prior knowledge of the model performance across input parameter space, including meshing and solver settings, which can require time consuming manual model probing or cause noisy and inconsistent predictions. The result is a probabilistic distribution of calibrated and validated FEM input parameters targeting measured data.

Additive manufacturing model calibration finite el↗

Influence of phase composition on microstructure and properties of Mg-5Al-0.4Mn-xRE (x = 0, 3 and 5 wt.%) alloys

The microstructure and mechanical properties investigations of two AME503 and AME505 experimental alloys in as-cast conditions were presented. The investigated materials were fabricated on the basis of the AM50 commercial magnesium alloy with 3 and 5 wt.% cerium rich mischmetal. In the as-cast condition, both experimental alloys were mainly composed of α-Mg, Al{sub 11}RE{sub 3} and Al{sub 10}RE{sub 2}Mn{sub 7} intermetallic phases. Additionally, due to non-equilibrium solidification conditions, a small amount of α + γ divorced eutectic and Al{sub 2}RE intermetallic phase were revealed. The obtained results also show a significant influence of rare earth elements on Brinell hardness, tensile and compression properties at ambient temperature and especially on creep properties at 473 K. Improved alloy properties with a rise in rare earth elements mass fraction results from an increase in Al{sub 11}RE{sub 3} phase volume fraction and suppression of α + γ eutectic volume fraction in the alloy microstructure. Additionally, the influence of rare earth elements on the dendrite arm space value was discussed. The presented results also proved the thermal stability of the intermetallic phases during creep testing. - Highlights: • Two different Mg-5Al-0.4Mn alloys containing 3 and 5 wt.% of rare earth elements were fabricated. • Addition of rare earth elements leads to a reduction of dendrite arm spaces. • Mechanical properties depend on the phase composition of the alloys. • The increase of the rare earth elements content causes rise of the creep resistance.

36 MATERIALS SCIENCE↗

Machine learning approaches for intentional materials engineering

In this article, the development of nanoporous metals and metallic composites through dealloying processes presents significant opportunities in materials engineering. However, designing multicomponent precursor alloys and establishing corresponding processing methods that yield predictable compositions and nanostructures remain a complex challenge. This article explores how machine learning (ML)-augmented computational and experimental methodologies can tackle these challenges by predicting precursor alloy compositions, final nanoporous structures, and mechanical properties, while integrating ML-enabled autonomous experimentation for material design and quantification. We highlight recent advancements in applying ML to nanostructured materials design via dealloying and discuss how techniques from other nanomaterial designs can be adapted for improved control over morphological and compositional outcomes in nanoporous and nanocomposite materials. Furthermore, we explore the role of ML in autonomous synchrotron x-ray experimentation, enabling real-time feedback between modeling and experimental setups. ML-driven approaches to microstructure characterization and mechanical property prediction are also examined, with a focus on modeling and advanced imaging techniques such as three-dimensional nanotomography. Finally, this article outlines future directions for ML-enhanced materials science, emphasizing the exploration of high-dimensional parameter spaces and the incorporation of materials kinetics into processing and property evaluation, ultimately advancing the design of nanoporous structures and materials science.

36 MATERIALS SCIENCE↗

Quantifying High-Performance Material Microstructure Using Nanomechanical Tools with Visual and Frequency Analysis

High-performance materials like ballistic fibers have remarkable mechanical properties owing to specific patterns of organization ranging from the molecular scale, to the micro scale and macro scale. Understanding these strategies for material organization is critical to improving the mechanical properties of these high-performance materials. In this work, atomic force microscopy (AFM) was used to detect changes in material composition at an extremely high resolution with transverse-stiffness scanning. New methods for direct quantification of material morphology were developed, and applied as an example to these AFM scans, although these methods can be applied to any spatially-resolved scans. These techniques were used to delineate between subtle morphological differences in commercial ultra-high-molecular-weight polyethylene (UHMWPE) fibers that have different processing conditions and mechanical properties as well as quantify morphology in commercial Kevlar®, a high-performance material with an entirely different organization strategy. Both frequency analysis and visual processing methods were used to systematically quantify the microstructure of the fiber samples in this study. These techniques are the first step in establishing structure-property relationships that can be used to inform synthesis and processing techniques to achieve desired morphologies, and thus superior mechanical performance.

Sandoz-Rosado, Emil↗

Influence of heat treatments on mechanical behavior of FV520B steel

Experimental tests have been carried out in order to investigate the influence of the heat treatments on the microstructures and mechanical properties of FV520B stainless steel. The fatigue strength of the common and heat-treated FV520B steels was rapidly assessed using the lock-in infrared thermographic methodology. Good agreements were achieved between the predicted values and those obtained by the traditional testing procedures. The temperature increments during the fatigue tests were tightly linked with the internal microstructural changes. The features of the fatigue fracture surface were observed by the scanning electron microscope. It is found that the fatigue microcracks were initiated from the corner of the specimen surface. The metallographic analysis shows that the improvement of the mechanical properties of FV520B steel is attributed to the formation of the fine-tempered martensite along with the secondary phase particles uniformly distributed at the grain boundary.

36 MATERIALS SCIENCE↗

Yttrium enrichment and improved magnetic properties in partially melted Y-Ba-Cu-O materials

The yttrium-rich compositions in the Y-Ba-Cu-O system were mapped out in a systematic manner to quantify their magnetic properties and to correlate them with the microstructure and phase composition as determined by scanning electron microscopy and X-ray diffraction analysis. It is found that the microstructure of Y-Ba-Cu-O compositions is a sensitive function of both their composition and processing conditions. Measurements of magnetic susceptibility and maximum (low-field) and remanent magnetization for the system Y:Ba:Cu = x:2:3 show highest values for x = 2. The corresponding structures involve numerous small crystals of Y2BaCuO5 (211) embedded in highly ordered assemblages of continous YBa2Cu3O(7-y) (123) layers.

Alterescu, Sidney↗

Thermoelectric properties of BiSbTe-type alloys prepared by chill-casting and cryo-milling

The thermoelectric properties of Bi x Sb 1-x Te 3 processed through milling have been extensively studied with varied results that needs to be rationalized. Since cryo-milling is a relatively cleaner milling process compared to other milling processes, in this study we explore this technique to reduce the particle size prior to compaction to get an insight into the thermoelectric properties. We first report the results of cryomilled BiSbTe 3 compacted by spark plasmas sintering (SPS) process and show that milling leads to a change in transport behavior from ‘p’ to ‘n’ type similar to that reported for Bi 2 Te 3 . It is shown that the defects induced by milling is responsible for this change in materials behavior. We further study the effect of change in Bi to Sb ratio and excess tellurium on the thermoelectric properties when processed through cryo-milling as well as casting using a chilled copper block. Excess tellurium leads to a microstructure containing a fraction of layered eutectic that gets further fragmented during cryo-milling. Although the Seebeck coefficient does not change significantly, reflecting the cleanliness of the process, the thermal conductivity changes during hot compaction leading to an improvement of ZT. However, a comparison of all the reported results does not reveal any systematics in thermoelectric properties reflecting the difficulties with these materials.

36 MATERIALS SCIENCE↗

Cast heat-resistant austenitic steel with improved temperature creep properties and balanced alloying element additions and methodology for development of the same

The present invention addresses the need for new austenitic steel compositions with higher creep strength and higher upper temperatures. The new austenitic steel compositions retain desirable phases, such as austenite, M.sub.23C.sub.6, and MC in its microstructure to higher temperatures. The present invention also discloses a methodology for the development of new austenitic steel compositions with higher creep strength and higher upper temperatures.

36 MATERIALS SCIENCE↗

Friction consolidation of gas-atomized Fe−Si powders for soft magnetic applications

Soft magnetic materials are often limited in scalability due to conventional processes that do not retain beneficial microstructures, and their associated physical properties, during densification. In this work, friction consolidation (FC) has been studied to fabricate Fe−Si soft magnetic materials from gas-atomized powder precursors. Fe−Si powder is consolidated using variable pressure and tool rotation speed in an effort to evaluate this unique densification approach for potential improvements in magnetic properties. FC, due to the high shear deformation involved, is shown to result in uniform gradual grain structure refinement across the consolidated workpiece from the center nearest the tool to the edge. Magnetic properties along different orientations indicate little, if any, textural orientation in the refined grain structure. The effect of annealing on the magnetic properties is evaluated and shown to decrease coercivity. FC processing was able to retain the magnetization of the original gas-atomized powders but further process optimization is needed to reach the optimal coercivity for the soft magnetic materials applications. - Highlights: •Friction stir processing was utilized to consolidate Fe−Si soft magnetic powders. •The resultant microstructure and magnetic properties were correlated to the processing conditions. •Friction consolidation refined the grain size of the materials by ~ 40%. •Annealing successfully reduced the coercivity induced by the stress during processing. •The results shine light on the possible scaling up of nanostructured materials.

36 MATERIALS SCIENCE↗

The Influence of the Regimes of Thermomechanical Treatments on the Features of Heterophase and Grain Structure of A V–Cr–Zr–Ta Alloy

A comparative investigation of the influence of thermomechanical treatment modes on the structural-phase state and mechanical properties of a V–Cr–Zr–Ta low-activation vanadium alloy is performed. It is demonstrated that the use of thermomechanical treatment improves the level of short-term strength at room and elevated temperatures. The alloy is characterized by high ductility in a wide range of temperatures irrespective of the regimes of thermomechanical treatment. It is found out that the V–Cr–Zr–Ta alloy possesses higher thermal microstructure stability and mechanical properties compared to those of the V–Ti–Cr alloys.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Organically Modified Nanoclay and Aluminum Hydroxide Incorporated Bionanocomposites towards Enhancement of Physico-mechanical and Thermal Properties of Lignocellulosic Structural Reinforcement

A range of bio-nanocomposites were prepared by incorporation of organo modified montmorillonite nanoclay (OMMT) with or without use of aluminum hydroxide (Al(OH){sub 3}) within polylactic acid (PLA) solution. Furthermore, the solution was employed for modification of ligno-cellulosic (jute) fabric structural reinforcements. The successful incorporation of nanofillers within the host polymer, polylactic acid (PLA) was confirmed by Fourier-transform infrared spectroscopy (FT-IR). Water uptake and swelling behaviour studies revealed that the water uptake and swelling ratio of bio-composites reduced significantly as compared to pristine jute fabric, whereas upon incorporation of OMMT and Al(OH){sub 3}, the water barrier properties reduced even further in the developed bio-nanocomposites. The flexural strength of the bio-nanocomposites also showed improved mechanical and dimensional stability. Synergistic effects of OMMT and Al(OH){sub 3} were observed in enhancing the aforementioned physico-mechanical properties. Scanning electron microscopy (SEM) studies revealed microstructural details of developed samples. Similarly, the thermo-gravimetric analysis and linear burning rate studies of Al(OH){sub 3 }treated bio-nanocomposite materials revealed enhanced thermal resistance and reduced flammability respectively compared to both pristine woven jute fabric and fabrics treated with PLA alone or those without Al(OH){sub 3}. From the above results it can safely be said that the bio-nanocomposite material can be a prospective candidate for development of flame retardant biopackaging.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dynamic Recrystallization and Grain Refinement of Fe-P-C-Si and Fe-P-C-Si-N Steels

Grain refinement is an effective technique to improve the mechanical properties of steels. In the present work, single-pass hot compression experiments have been conducted on two different compositions of high phosphorous steels to study the microstructural evolution and ferrite grain refinement at various strain rates and deformation temperatures, i.e., 0.01-10 s{sup −1} and 750-1050 °C, respectively. Optical metallography has been employed to understand the physical processes that take place during hot deformation process. The results indicate that when these compositions of high phosphorous steels are worked at relatively low temperatures in the intercritical regions, a ferrite grain size of 5-7 µm is obtained. It is observed that the grain size decreases with an increase in strain rate and with the decrease in deformation temperature. Based on the values of stress exponent (n) obtained in the present work, dislocation creep is identified as the deformation mechanism. The activation energies for deformation of these two types of high phosphorous steels have been calculated. The effect of the alloying elements on the stress–strain curve, microstructure, and grain refinement has been discussed.

36 MATERIALS SCIENCE↗

Vacuum-assisted extrusion to reduce internal porosity in large-format additive manufacturing

Large-scale 3D printing of polymer composite structures has gained popularity and seen extensive use over the last decade. Much of the research related to improving the mechanical properties of 3D-printed parts has focused on exploring new materials and optimizing print parameters to improve geometric control and minimize voids between printed beads. However, porosity at the microstructural level (within the printed bead) has been much less studied although it is almost universally observed at levels of 4 %-10 % when using fiber reinforced materials. This study introduces a vacuum-assist approach that minimizes internal porosity by removing ambient air from the interstitial space between pellets in the hopper and acts as a negative pressure vent for gases that evolve during the initial stages of single-screw extrusion. Vacuum-assisted extrusion was able to reduce porosity below 2 % across a wide range of processing parameters, moisture content, fiber reinforcements, and printing platforms. Specifically, when printing on a large-format extruder (Strangpresse Model-30), the vacuum-assisted extrusion reduced internal porosity by 35–75 % compared to conventional non-vacuum extrusion, and only pores with length scale > 2 microns are affected. The success of this approach prompted the design of a patent-pending continuous vacuum hopper relevant for large-scale 3D printing on commercial systems.

36 MATERIALS SCIENCE↗

On the interactions between molten aluminum and high entropy alloy particles during aluminum matrix composite processing

The feasibility of adding AlCrTiV high entropy alloy (HEA) particles to molten aluminum to make metal matrix composites was studied. Equiatomic AlCrTiV HEA particles, produced by a solid state reduction process, were dispersed into pure aluminum and 7075 alloy (Al-5.8Zn-2.3Mg-1.4Cu, all weight %) melt and by a ultrasonic dispenser. It was found that the AlCrTiV particles reacted with molten aluminum, leading to the formation of Al 45 (Cr,V) 7 and Al 3 Ti intermetallic phases in the aluminum matrix composites. Although the AlCrTiV HEA particles did not survive in molten aluminum during composite processing, the final composite materials showed significantly improved mechanical properties, due to grain refinement and dispersion strengthening. Finally, the research suggests that the interactions between matrix aluminum alloys and the particles are key in controlling the final microstructure and properties of the composites.

36 MATERIALS SCIENCE↗

Bridging Scales to Model Reactive Diffusive Transport in Porous Media

Published by ECS. Two novel scale-bridging algorithms to model reaction-diffusion transport in porous media are presented. The algorithms are based on direct numerical simulations and couple the information of a micro-scale model, which accounts for the large field of view provided by micro X-ray computed tomography (X-ray CT), and a nano-scale model, which locally resolves transport in the fine structure extracted from nano X-ray CT. The micro-scale model is discretized in the through-plane direction into a 1D grid, where effective properties and internal boundaries are determined based on the results from the nano-scale model. The validated algorithms are used to examine transport of oxygen in precious group metal-free electrodes considering both zero- and first-order kinetics. Unlike conventional methods, the results show that the effective diffusivity is not a passive property but increases in regions where the reaction-rate coefficient is large. The proposed algorithms account for the multiscale coupling of reaction-diffusion transport and material microstructure, thus improving the predictions compared to conventional methods.

42 ENGINEERING↗

The NBS: Processing/Microstructure/Property Relationships in 2024 Aluminum Alloy Plates

As received plates of 2024 aluminum alloy were examined. Topics covered include: solidification segregation studies; microsegregation and macrosegregation in laboratory and commercially cast ingots; C-curves and nondestructive evaluation; time-temperature precipitation diagrams and the relationships between mechanical properties and NDE measurements; transmission electron microscopy studies; the relationship between microstructure and properties; ultrasonic characterization; eddy-current conductivity characterization; the study of aging process by means of dynamic eddy current measurements; and Heat flow-property predictions, property degradations due to improve quench from the solution heat treatment temperature.

Ives, L. K.↗

Continuous fiber-reinforced titanium aluminide composites

An account is given of the fabrication techniques, microstructural characteristics, and mechanical behavior of a lightweight, high service temperature SiC-reinforced alpha-2 Ti-14Al-21Nb intermetallic-matrix composite. Fabrication techniques under investigation to improve the low-temperature ductility and environmental resistance of this material system, while reducing manufacturing costs to competitive levels, encompass powder-cloth processing, foil-fiber-foil processing, and thermal-spray processing. Attention is given to composite microstructure problems associated with fiber distribution and fiber-matrix interfaces, as well as with mismatches of thermal-expansion coefficient; major improvements are noted to be required in tensile properties, thermal cycling effects, mechanical damage, creep, and environmental effects.

Mackay, R. A.↗

Bulk YBa2Cu3O(x) superconductors through pressurized partial melt growth processing

A novel pressurized partial melt growth process has been developed for producing large pieces of bulk Y-Ba-Cu-O superconductors. During long-time partial melt growth stage, an additional driving force for solidification is obtained by using pressurized oxygen gas. The microstructure and superconducting properties of the resulting samples were investigated. It was found that this new technique can eliminate porosity and inhomogeneity, promote large-scale grain-texturing, and improve interdomain coupling as well.

Hu, S.↗