Search NASA⌕ Search

SEARCH · Search NASA

Results for “information passing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Rate-Dependent Aging Resulting from Fast Charging of Li-Ion Cells

The mass electrification of personal and service vehicles is reliant on the ability of battery packs to undergo extreme fast recharging. A central challenge is that the repeated exposure to high currents can trigger and/or accelerate mechanisms of performance degradation, such as lithium deposition, mechanical damage of active material particles, and impedance rise. Here, we investigate whether constraining high-rate charging to limited state-of-charge (SOC) ranges can mitigate these aging processes. Our experiments map the boundaries of lithium plating conditions, and also indicate that permanent losses of electrode capacity appear to be a function of cycle number, but not charging rate. Interestingly, we show that impedance rise appears to depend on charging rate alone, and not on the amount of charge passed at each cycle. This observation suggests that limiting fast charging to a narrow SOC range would only delay cell aging, but not fully prevent it from happening. We identify oxide-particle cracking as the likely mechanism for this impedance rise, suggesting that particle and electrode design are essential to enable fast charging. The findings of this work can inform the development of fast-charging protocols that are less damaging to cell health.

25 ENERGY STORAGE↗
NASA NTRS1981

Horizontal Conflict Resolution Maneuvers with a Cockpit Display of Traffic Information

Pilot resolution of potential conflicts in the horizontal plane when the only information available on the other aircraft was presented on a Cockpit Display of Traffic Information (CDTI) is investigated. The pilot's task was to assess the situation and if necessary maneuver so as to avoid the other aircraft. No instructions were given on evasive strategy or on what was considered to be an acceptable minimum separation. The results indicate that pilots had a strong bias of turning toward the intruder aircraft in order to pass behind it. In more than 50% of the encounters with a 90 degree crossing angle in which the intruder aircraft was programmed to pass behind the aircraft, the pilots maneuvered so as to pass behind the intruder. This bias was not as strong with the display which showed a prediction of the intruder's relative velocity. The average miss distance for all encounters was about 4500 feet.

Palmer, E.↗
NASA NTRS2001

Time-Dependent Simulations of Incompressible Flow in a Turbopump Using Overset Grid Approach

This viewgraph presentation provides information on mathematical modelling of the SSME (space shuttle main engine). The unsteady SSME-rig1 start-up procedure from the pump at rest has been initiated by using 34.3 million grid points. The computational model for the SSME-rig1 has been completed. Moving boundary capability is obtained by using DCF module in OVERFLOW-D. MPI (Message Passing Interface)/OpenMP hybrid parallel code has been benchmarked.

Kiris, Cetin↗
NASA NTRS2003

HEASARC Software Archive

(1) Chandra Archive: SAO has maintained the interfaces through which HEASARC gains access to the Chandra Data Archive. At HEASARC's request, we have implemented an anonymous ftp copy of a major part of the public archive and we keep that archive up-to- date. SAO has participated in the ADEC interoperability working group, establishing guidelines or interoperability standards and prototyping such interfaces. We have provided an NVO-based prototype interface, intending to serve the HEASARC-led NVO demo project. HEASARC's Astrobrowse interface was maintained and updated. In addition, we have participated in design discussions surrounding HEASARC's Caldb project. We have attended the HEASARC Users Group meeting and presented CDA status and developments. (2) Chandra CALDB: SA0 has maintained and expanded the Chandra CALDB by including four new data file types, defining the corresponding CALDB keyword/identification structures. We have provided CALDB upgrades for the public (CIAO) and for Standard Data Processing. Approximately 40 new files have been added to the CALDB in these version releases. There have been in the past year ten of these CALDB upgrades, each with unique index configurations. In addition, with the inputs from software, archive, and calibration scientists, as well as CIAO/SDP software developers, we have defined a generalized expansion of the existing CALDB interface and indexing structure. The purpose of this is to make the CALDB more generally applicable and useful in new and future missions that will be supported archivally by HEASARC. The generalized interface will identify additional configurational keywords and permit more extensive calibration parameter and boundary condition specifications for unique file selection. HEASARC scientists and developers from SAO and GSFC have become involved in this work, which is expected to produce a new interface for general use within the current year. (3) DS9: One of the decisions that came from last year's HEADCC meeting was to make the ds9 image display program the primary vehicle for displaying line graphics (as well as images). The first step required to make this possible was to enhance the line graphics capabilities of ds9. SAO therefore spent considerable effort upgrading ds9 to use Tcl 8.4 so that the BLT line graphics package could be built and imported into ds9 from source code, rather than from a pre-built (and generally outdated) shared library. This task, which is nearly complete, allows us to extend BLT as needed for the HEAD community. Following HEADCC discussion concerning archiving and the display of archived data, we extended ds9 to support full access to many astronomical Web-based archives sites, including HEASARC, MAST, CHANDRA, SKYVIEW, ADS, NED, SIMBAD, IRAS, NVRO, SAO TDC, and FIRST. Using ds9's new internal Web access capabilities, these archives can be accessed via their Web page. FITS images, plots, spectra, and journal abstracts can be referenced, down-loaded, and displayed directly and easily in ds9. For more information, see: http://hea-www.harvard.edu/saord/ds9. Also after the HEADCC discussion concerning region filtering, we extended the Funtools sample implementation of region filtering as described in: http://hea-www.harvard.edu/saord/funtools/regions.html. In particular, we added several new composite regions for event and image filtering, including elliptical and box annuli. We also extended the panda (Pie AND Annulus) region support to include box pandas and elliptical pandas. These new composite regions are especially useful in programs that need to count photons in each separate region using only a single pass through the data. Support for these new regions was added to ds9. In the same vein, we developed new region support for filtering images using simple FITS image masks, i.e. 8-bit or 16-bit FITS images where the value of a pixel is the region id number for that pixel. Other important enhancements to DS9 this year, include supporor multiple world coordinate systems, three dimensional event file binning, image smoothing, region groups and tags, the ability to save images in a number of image formats (such as JPEG, TIFF, PNG, FITS), improvements in support for integrating external analysis tools, and support for the virtual observatory. In particular, a full-featured web browser has been implemented within D S 9 . This provides support for full access to HEASARC archive sites such as SKYVIEW and W3BROWSE, in addition to other astronomical archives sites such as MAST, CHANDRA, ADS, NED, SIMBAD, IRAS, NVRO, SA0 TDC, and FIRST. From within DS9, the archives can be searched, and FITS images, plots, spectra, and journal abstracts can be referenced, downloaded and displayed The web browser provides the basis for the built-in help facility. All DS9 documentation, including the reference manual, FAQ, Know Features, and contact information is now available to the user without the need for external display applications. New versions of DS9 maybe downloaded and installed using this facility. Two important features used in the analysis of high energy astronomical data have been implemented in the past year. The first is support for binning photon event data in three dimensions. By binning the third dimension in time or energy, users are easily able to detect variable x-ray sources and identify other physical properties of their data. Second, a number of fast smoothing algorithms have been implemented in DS9, which allow users to smooth their data in real time. Algorithms for boxcar, tophat, and gaussian smoothing are supported.

White, Nicholas↗
NASA NTRS2004

Simplifying CEA through Excel, VBA, and Subeq

Many people use compound equilibrium programs for very different reasons, varying from refrigerators to light bulbs to rockets. A commonly used equilibrium program is CEA. CEA can take various inputs such as pressure, temperature, and volume along with numerous reactants and run them through equilibrium equations to obtain valuable output information, including products formed and their relative amounts. A little over a year ago, Bonnie McBride created the program subeq with the goal to simplify the calling of CEA. Subeq was also designed to be called by other programs, including Excel, through the use of Visual Basic for Applications (VBA). The largest advantage of using Excel is that it allows the user to input the information in a colorful and user-friendly environment while allowing VBA to run subeq, which is in the form of a FORTRAN DLL (Dynamic Link Library). Calling subeq in this form makes it much faster than if it were converted to VBA. Since subeq requires such large lists of reactant and product names, all of which can't be passed in as an array, subeq had to be changed to accept very long strings of reactants and products. To pass this string and adjust the transfer of input and output parameters, the subeq DLL had to be changed. One program that does this is Compaq Visual FORTRAN, which allows DLLs to be edited, debugged, and compiled. Compaq Visual FORTRAN uses FORTRAN 90/95, which has additional features to that of FORTRAN 77. My goals this summer include finishing up the excel spreadsheet of subeq, which I started last summer, and putting it on the Internet so that others can use it without having to download my spreadsheet. To finish up the spreadsheet I will need to work on debugging current options and problems. I will also work on making it as robust as possible, so that all errors that may arise will be clearly communicated to the user. New features will be added old ones will be changed as I receive comments from people using the spreadsheet. To implement this onto the Internet, I will need to develop an XML input/output format and learn how to write HTML.

Foster, Ryan↗
NASA NTRS2007

Space Flight Requirements for Fiber Optic Components; Qualification Testing and Lessons Learned

"Qualification" of fiber optic components holds a very different meaning than it did ten years ago. In the past, qualification meant extensive prolonged testing and screening that led to a programmatic method of reliability assurance. For space flight programs today, the combination of using higher performance commercial technology, with shorter development schedules and tighter mission budgets makes long term testing and reliability characterization unfeasible. In many cases space flight missions will be using technology within years of its development and an example of this is fiber laser technology. Although the technology itself is not a new product the components that comprise a fiber laser system change frequently as processes and packaging changes occur. Once a process or the materials for manufacturing a component change, even the data that existed on its predecessor can no longer provide assurance on the newer version. In order to assure reliability during a space flight mission, the component engineer must understand the requirements of the space flight environment as well as the physics of failure of the components themselves. This can be incorporated into an efficient and effective testing plan that "qualifies" a component to specific criteria defined by the program given the mission requirements and the component limitations. This requires interaction at the very initial stages of design between the system design engineer, mechanical engineer, subsystem engineer and the component hardware engineer. Although this is the desired interaction what typically occurs is that the subsystem engineer asks the components or development engineers to meet difficult requirements without knowledge of the current industry situation or the lack of qualification data. This is then passed on to the vendor who can provide little help with such a harsh set of requirements due to high cost of testing for space flight environments. This presentation is designed to guide the engineers of design, development and components, and vendors of commercial components with how to make an efficient and effective qualification test plan with some basic generic information about many space flight requirements. Issues related to the ~ physics of failure, acceptance criteria and lessons learned will also be discussed to assist with understanding how to approach a space flight mission in an ever changing commercial photonics industry.

Ott, Melanie N.↗
NASA NTRS2020

NASA Earth Science Data Systems: Open Data, Services and Software

Open, Public, Electronic and Necessary (OPEN) Government Data Act, which requires all non-sensitive government data to be made available in open and machine-readable formats by default is part of the overall Foundations for Evidence-Based Policymaking (FEBP) Act passed in late 2018. This town hall will bring together data officers and policy makers from NOAA, EPA, NASA and others to discuss the impact of the act on data management strategies going forward. In 1994 NASA's Earth Science Division committed to an open data policy for all civilian Earth satellite data. NASA's Earth Observing System Data and Information System (EOSDIS) became the first large scale data system to facilitate public access to global Earth system data and information. This presentation reviews key elements of EOSDIS data policy and data management activities that support the OPEN Government Data Act.

Moses, John F.↗
NASA NTRSDate not supplied

X-Ray Computed Tomography of Apollo Drive Tube 73001 as Part of the Apollo Next Generation Sample Analysis Program

Introduction: Starting in 2019, the Apollo Next Generation Sample Analysis (ANGSA) Program has enabled consortium studies of specially curated Apollo samples that were previously unstudied (or under studied). This program was intended as a participating scientist program for these Apollo samples, as well as a preparation for upcoming lunar sample return missions (e.g., Artemis). The work began with studies of unsealed core tube 73002 [1,2] that is the upper ~35 cm of an Apollo 17 double drive tube (~70 cm total depth) collected on the landslide deposit near Lara Crater at Station 3 in the Taurus Littrow Valley. More recently the program extended to the study of a variety of frozen Apollo 17 samples [3], as well as the gas extraction [4] and dissection [5] of 73001, the lower half of the station 3 double drive tube. Sample 73001 was sealed under vacuum on the Moon in a Core Sample Vacuum Container (CSVC). In this abstract we will examine the role of X-ray Computed Tomography (XCT) during the preliminary examination process for sealed core 73001, including: (1) engineering scans to aid in understanding the gas extraction process, (2) whole-core scanning prior to opening to inform extrusion and dissection work, and (3) individual particle scanning to characterize rock fragment lithologies for follow on studies. Methodology: Sample 73001 is a 33 cm long, 4 cm diameter regolith sample collected inside a lunar drive tube (~1 mm aluminum walls). That drive tube was sealed inside a 0.5 mm thick stainless steel (SS) CSVC. XCT scans for engineering purposes were done on the Nikon XTH 320 system at Johnson Space Center using the 225 kV multi-metal reflection source at 215 kV, 179 A, and a 38.49 m voxel size. Individual >4 mm particles separated from the core during processing (then triply sealed in Teflon bags) were also scanned at JSC using the 180 kV source at 90 kV, 33 A, and a 2.98 – 10.65 m voxel size. Whole-core scans were done at the University of Texas High-Resolution X-ray Computed Tomography Facility (UTCT) on the 225 kV reflection source on the North Star Imaging cabinet XCT system. These scans included: (1) a series of 9 overlapping super-resolution scans each covering a ~4 cm length of the tube at 190 kV, 180 µA, and a 12.9 µm voxel size and (2) a lower resolution continuous helical scan of the entire core at 190 kV, 180 µA, and a 51.8 µm voxel size. Progress and Results: Before piercing and extracting the gas from sample 73001, an XCT scan of the bottom portion of the CSVC was used to confirm the location of the Teflon cap on the inner drive tube and whether there was an “air” gap between the Teflon cap and the CSVC. This was to ensure the Teflon cap (which immobilized the soil inside the drive tube) was not accidentally pierced during gas extraction. Similarly, after piercing, the bottom and top portions of the CSVC were scanned in order to capture engineering knowledge about the results of the piercing process, as well as the metal knife edge vacuum seal (SS into an In-Ag alloy). Both scans will provide constraints on future work of this type, both for the design of tools used on the lunar surface during Artemis, as well as how we open future samples of this type. An unexpected finding from these engineering scans was that the device in the drive tube that immobilizes the regolith (the keeper) was not seated in the tube properly. This meant that (1) the drive tube could not be removed from the CSVC for the trip to UTCT, and (2) the procedure for opening and extruding the drive tube had to be modified. Had either of these things not been known prior to opening the CSVC, it could have led to an inability to XCT scan the whole core at high resolution and/or potential disruption of the core stratigraphy during extrusion. At UTCT, the entire length of the core was scanned at high resolution (12.9 microns per voxel). This scan serves multiple purposes: (1) A lower resolution (and uncorrected) version of these scans stitched together was used to help inform the processors of potential pitfalls during extrusion and dissection (voids, angular fragments at the edges of the sample, etc.); and (2) the full resolution corrected data will serve as the permanent in situ record of the stratigraphy of the sample and will enable future researchers to perform a variety of analyses. All 121 >4 mm particles separated during dissection pass 1 of sample 73001 have been individually scanned. These scans clearly show the lithology of each particle while keeping the particles in pristine condition (they are individually triply bagged in Teflon within our N2 purged processing cabinets). Because of the dust adhering to particle exteriors, it would otherwise be impossible to determine lithologies in a non-contaminating way. Thus far the types of lithologies seen in sample 73001 (e.g., regolith breccias, impact-melt breccias, agglutinates, and bas-alts) are similar to those previously identified in sample 73002 [2]. By the time of the meeting, all particles from all 3 dissection passes will have been scanned and statistics on the different lithologies in 73001 compiled. References: [1] Shearer et al. (2020) 51st LPSC, abstract 1181. [2] Zeigler et al. (2020) 51st LPSC, abstract 3023. [3] Kent et al. (2022) This Volume. [4] McDonald et al. (2022) European Lunar Symposium. [5] Gross et al (2022) This volume.

Moon↗
DOE OSTI2026

Unsupervised atomic data mining via multi-kernel graph autoencoders for machine learning force fields

Constructing a chemically diverse dataset while avoiding sampling bias is critical to training efficient and generalizable force fields. However, in computational chemistry and materials science, many common dataset generation techniques are prone to oversampling regions of the potential energy surface. Furthermore, these regions can be difficult to identify and isolate from each other or may not align well with human intuition, making it challenging to systematically remove bias in the dataset. While traditional clustering and pruning (down-sampling) approaches can be useful for this, they can often lead to information loss or a failure to properly identify distinct regions of the potential energy surface due to difficulties associated with the high dimensionality of atomic descriptors. In this work, we introduce the Multi-kernel Edge Attention-based Graph Autoencoder (MEAGraph) model, an unsupervised approach for analyzing atomic datasets. MEAGraph combines multiple linear kernel transformations with attention-based message passing to capture geometric sensitivity and enable effective dataset pruning without relying on labels or extensive training. Demonstrated applications on niobium, tantalum, and iron datasets show that MEAGraph efficiently groups similar atomic environments, allowing for the use of basic pruning techniques for removing sampling bias. This approach provides an effective method for representation learning and clustering that can be used for data analysis, outlier detection, and dataset optimization.

Materials science↗
NASA NTRS2003

Use of Multi-Resolution Wavelet Feature Pyramids for Automatic Registration of Multi-Sensor Imagery

The problem of image registration, or alignment of two or more images representing the same scene or object, has to be addressed in various disciplines that employ digital imaging. In the area of remote sensing, just like in medical imaging or computer vision, it is necessary to design robust, fast and widely applicable algorithms that would allow automatic registration of images generated by various imaging platforms at the same or different times, and that would provide sub-pixel accuracy. One of the main issues that needs to be addressed when developing a registration algorithm is what type of information should be extracted from the images being registered, to be used in the search for the geometric transformation that best aligns them. The main objective of this paper is to evaluate several wavelet pyramids that may be used both for invariant feature extraction and for representing images at multiple spatial resolutions to accelerate registration. We find that the band-pass wavelets obtained from the Steerable Pyramid due to Simoncelli perform better than two types of low-pass pyramids when the images being registered have relatively small amount of nonlinear radiometric variations between them. Based on these findings, we propose a modification of a gradient-based registration algorithm that has recently been developed for medical data. We test the modified algorithm on several sets of real and synthetic satellite imagery.

Zavorin, Ilya↗
NASA NTRS2024

Assessment of Base Loads Generated by an Exercise Device in the HALO Module

The purpose of this document is to prescribe a uniform procedure that can be used to postprocess base loads generated by a crew member and an exercise device in the Gateway Habitation and Logistics Outpost (HALO) module. This memo has three primary sections. First, the exercise loads pass through a Vibration Isolation and Stabilization (VIS) system notionally depicted in Figure 1 for the purpose of preliminary analyses. This is described in Section 2. Next, these loads are processed in frequency domain as explained in Section 3. Finally, the resulting outputs are compared with a Gateway Program Loads and Dynamics (L&D) allocation given to the VIS system. This information is provided in Section 4.

Exercise↗
DOE OSTI2024

GCAM–GLORY v1.0: representing global reservoir water storage in a multi-sector human–Earth system model

Abstract. Reservoirs play a significant role in modifying the spatiotemporal availability of surface water to meet multi-sector human demands, despite representing a relatively small fraction of the global water budget. Yet the integrated modeling frameworks that explore the interactions among climate, land, energy, water, and socioeconomic systems at a global scale often contain limited representations of water storage dynamics that incorporate feedbacks from other systems. In this study, we implement a representation of water storage in the Global Change Analysis Model (GCAM) to enable the exploration of the future role (e.g., expansion) of reservoir water storage globally in meeting demands for, and evolving in response to interactions with, the climate, land, and energy systems. GCAM represents 235 global water basins, operates at 5-year time steps, and uses supply curves to capture economic competition among renewable water (now including reservoirs), non-renewable groundwater, and desalination. Our approach consists of developing the GLObal Reservoir Yield (GLORY) model, which uses a linear programming (LP)-based optimization algorithm and dynamically linking GLORY with GCAM. The new coupled GCAM–GLORY approach improves the representation of reservoir water storage in GCAM in several ways. First, the GLORY model identifies the cost of supplying increasing levels of water supply from reservoir storage by considering regional physical and economic factors, such as evolving monthly reservoir inflows and demands, and the leveled cost of constructing additional reservoir storage capacity. Second, by passing those costs to GCAM, GLORY enables the exploration of future regional reservoir expansion pathways and their response to climate and socioeconomic drivers. To guide the model toward reasonable reservoir expansion pathways, GLORY applies a diverse array of feasibility constraints related to protected land, population, water sources, and cropland. Finally, the GLORY–GCAM feedback loop allows evolving water demands from GCAM to inform GLORY, resulting in an updated supply curve at each time step, thus enabling GCAM to establish a more meaningful economic value of water. This study improves our understanding of the sensitivity of reservoir water supply to multiple physical and economic dimensions, such as sub-annual variations in climate conditions and human water demands, especially for basins experiencing socioeconomic droughts.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1973

NASTRAN multipartitioning and one-shot substructuring

For intermediate size problems where all the data is accessible, the present method of substructuring in three separate phases (for static analysis) is unneccessarily cumbersome. The versatility of NASTRAN's DMAP and internal logic lends itself to finding a practical alternative to these procedures whereby self-contained special-purpose ALTER packages can be written to be run in one pass. Two examples are presented here under the titles of multipartitioning and one-shot substructuring. The flow of multipartitioning resembles that of the present three-phase substructuring. The basic effect is to partition the structure into substructures and operate on each substructure separately. This can be used to reduce the bandwidth of a given problem as well as to store information which will allow a change to be made in one of the substructures in a later run. This latter procedure is carried out in a second program titled one-shot substructuring.

Levy, A.↗
NASA NTRS2005

NASA, the Fisherman's Friend

Every angler has his secrets, whether it be an old family recipe for stink bait, a midnight worm-hunting ritual, or the most coveted of all, the no-fail fishing hole. Most of these secrets are lore and legend, passed through generations, and coveted more than the family s best tableware. Each of these kernels of wisdom promises the fisherman a bite at the end of the line, but very few are rooted in fact and science. There is one, though.... NASA partnered with a company on the bayous of Mississippi and Louisiana to use satellite data to create a marine information system, a space-age fish finder. This product provides up-to-date information about the location of a variety of fish, including yellowfin tuna, bluefish, blue marlin, white marlin, sailfish, blackfin tuna, little tunny, and swordfish. The system shows peaked catch rates, and may be the only true fish-finding product on the market.

Source record↗
NASA NTRS2016

MoonDB: Restoration and Synthesis of Lunar Petrological and Geochemical Data

About 2,200 samples were collected from the Moon during the Apollo missions, forming a unique and irreplaceable legacy of the Apollo program. These samples, obtained at tremendous cost and great risk, are the only samples that have ever been returned by astronauts from the surface of another planetary body. These lunar samples have been curated at NASA Johnson Space Center and made available to the global research community. Over more than 45 years, a vast body of petrological, geochemical, and geochronological studies of these samples have been amassed, which helped to expand our understanding of the history and evolution of the Moon, the Earth itself, and the history of our entire solar system. Unfortunately, data from these studies are dispersed in the literature, often only available in analog format in older publications, and/or lacking sample metadata and analytical metadata (e.g., information about analytical procedure and data quality), which greatly limits their usage for new scientific endeavors. Even worse is that much lunar data have never been published, simply because no forum existed at the time (e.g., electronic supplements). Thousands of valuable analyses remain inaccessible, often preserved only in personal records, and are in danger of being lost forever, when investigators retire or pass away. Making these data and metadata publicly accessible in a digital format would dramatically help guide current and future research and eliminate duplicated analyses of precious lunar samples.

Lehnert, Kerstin A.↗
DOE OSTI2022

Support for climate policy researchers

In the past 2 years, the European Union and the United States announced plans to spend $573 and $391 billion, respectively, through 2030 on climate actions and passed landmark legislation such as the US Inflation Reduction Act. Although unprecedented in size and scope, these combined investments of $964 billion pale in comparison to the more than $4 trillion in global clean energy investment needed annually by 2030 to stay on track for net zero greenhouse gas emissions by 2050. Furthermore, to maximize the impact of this public money, efficient policies informed by independent, objective analysis will be needed. Yet scientists who commit to policy-relevant research face unique challenges that must be addressed.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1985

A new look at sound generation by blade/vortex interaction

As a preliminary attempt to understand the dynamics of blade/vortex interaction, the two-dimensional problem of a rectilinear vortex filament interacting with a Joukowski airfoil is analyzed in both the lifting and nonlifting cases. The vortex velocity components could be obtained analytically and integrated to determine the vortex trajectory. With this information, the aeroacoustic low-frequency Green's function approach could then be employed to calculate the sound produced during the encounter. The results indicate that the vortex path deviates considerably from simple convection due to the presence of the airfoil and that a reasonably sharp sound pulse is radiated during the interaction whose fundamental frequency is critically dependent upon whether the vortex passes above or below the airfoil. Determination of this gross parameter of the interaction is shown to be highly nonlinearly dependent upon airfoil circulation, vortex circulation, and initial position.

Hardin, J. C.↗
NASA NTRS1998

Lasers in Earth and Planetary Exploration

For over 3 decades, lasers have been a tool of the space programs of the world for accomplishing a variety of engineering and scientific objectives. The majority of these uses have, however, been largely Earth-based and only a few lasers have actually been flown and operated in Earth orbit and even fewer on missions to the planets. However, in the last few years laser altimeters, lidars, and ranging systems have been part of space missions to the moon, an asteroid, and Mars; and more are planned and contemplated in the future exploration of the Earth and solar system. Early in 1994, the Clementine mission was launched to the moon and carried a laser altimeter that made the first systematic topographic survey of the moon during its 2-month observation period. This mission significantly improved our understanding of the shape and topography of the moon and along with gravity information obtained from the tracking data modified some of our thinking about the moon, the thickness of ice crust and the isostatic state of the highlands and basins. On September 11, 1997, the Mars Global Surveyor (MGS) entered into orbit around Mars and the Mars Orbiter Laser Altimeter (MOLA) started to map the topography of the planet to unprecedented accuracy. On its first pass across the planet, MOLA showed large areas of the northern hemisphere to be flatter than any other known surface on Earth or any other body explored to date. In January 1999, the NEAR spacecraft which carries a laser ranger (NLR), will arrive at the S-type asteroid, Eros, and during the following year the NLR will help determine the shape and rotational dynamics of this asteroid. In the Spring of 2000, the Vegetation Canopy Lidar (VCL) mission will be launched and employing a multi-beam laser altimeter (MBLA) will measure the Earth's tree canopy shapes and heights and begin to globally monitor the biomass. The following year, in 2001, the Geoscience Laser Altimeter System, which carries a 2 wavelength laser altimeter of a few centimeter accuracy, will begin a multi-year observation program of the Earth's icecaps, land mass, oceans and the clouds of the atmosphere. At the same time, laser ranging to satellites and the moon is likely to be poised to reach to the planets and track spacecraft throughout the inner solar system by applying optical transponder technology to increase its distance capability.

Smith, David E.↗