Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

1.5 MeV proton irradiation effects on electrical and structural properties of TiO{sub 2}/n-Si interface

In this paper, we report the effect of 1.5 MeV proton beam irradiation dose on the structural and electrical properties of TiO{sub 2} thin films deposited on n–Si substrates. The formation and transformation of different TiO{sub 2} phases in the irradiated thin films were characterized by X-ray diffraction and X-ray photoelectron spectroscopy (XPS). X-ray diffraction measurements revealed that the as grown film was rich in Ti{sub 5}O{sub 9} phase and then converted to mixed phases of TiO{sub 2} (rutile and anatase) after exposure with radiation doses up to 5 × 10{sup 14} cm{sup −2}. The XPS results revealed the formation of oxygen vacancy (negative) traps in the exposed TiO{sub 2} films, which showed strong dependence on the dose. The C-V measurements showed that proton radiations also damaged the Si substrate and created deep level defects in the substrate, which caused a shift of 0.26 ± 0.01 V in the flat band voltage (V{sub FB}). I–V measurements showed that the ideality factor increased and the rectification ratio dropped with the increase in the radiation dose. The present study showed the stability of TiO{sub 2}/Si interface and TiO{sub 2} film as an oxide layer against proton radiations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Regenerative Solid Interfaces Enhance High-Performance All- Solid-State Lithium Batteries

All-solid-state Lithium batteries (ASSLBs) have gained widespread attention in recent years. However, their performance is still largely limited by the poor transport properties and stability of the solid-solid interfaces (SSIs). In this study, we report a new strategy for creating a reversible interface with good conductivity and self-adaptive mechanical properties for high-performance all-solid-state lithium batteries (ASSLBs). The interface is formed in situ from nanosized lithium iodide (LiI), a component of the solid-state electrolyte (SSE), which flows plastically along the SSE interfaces under high pressure due to its high ductility. Moreover, LiI segregates and enriches along the Li/SSE interfaces, reversibly enhancing Li plating/stripping due to its lithophilicity and high ionic conductivity. This dynamic LiI interface enables stable operation of metallic Li anode (>1000 h) at high current densities and elevated temperatures, and long-term cycling of all-solid-state Li-sulfur batteries (>250 cycles) with high sulfur utilization rate (>1400 mAh g-1) and areal capacity (>2 mAh cm-2). This study reveals a unique role of LiI in building robust SSIs and provides new insights into the design of novel SSEs and interfaces for high-performance ASSLBs.

Yu, Zhaoxin↗

Reduction of the interfacial trap density of indium-oxide thin film transistors by incorporation of hafnium and annealing process

The stable operation of transistors under a positive bias stress (PBS) is achieved using Hf incorporated into InO{sub x}-based thin films processed at relatively low temperatures (150 to 250 °C). The mobilities of the Hf-InO{sub x} thin-film transistors (TFTs) are higher than 8 cm{sup 2}/Vs. The TFTs not only have negligible degradation in the mobility and a small shift in the threshold voltage under PBS for 60 h, but they are also thermally stable at 85 °C in air, without the need for a passivation layer. The Hf-InO{sub x} TFT can be stable even annealed at 150 °C for positive bias temperature stability (PBTS). A higher stability is achieved by annealing the TFTs at 250 °C, originating from a reduction in the trap density at the Hf-InO{sub x}/gate insulator interface. The knowledge obtained here will aid in the realization of stable TFTs processed at low temperatures.

36 MATERIALS SCIENCE↗

Solvating power series of electrolyte solvents for lithium batteries

From dictating the redox potential of electrolyte solvents to shaping the stability of solid-electrolyte interfaces, solvation plays a critical role in the electrochemistry of electrolytes. To efficiently design functional electrolytes for lithium batteries, it is particularly important to understand the relative solvating ability of each individual organic solvent, because most of the electrolyte systems are comprised of two or more electrolyte solvents. Using a newly developed internally referenced diffusion-ordered spectroscopy technique and diffusion coefficient–coordination ratio ($D–α$) analysis, we successfully constructed a solvating power series for common electrolyte solvents. We demonstrated the usefulness of this solvating power series in designing more reliable electrolyte system by selecting an appropriate fluorinated electrolyte solvent for a high-voltage lithium metal battery (LMB) as an example. For a methyl(2,2,2-trifluoroethyl)carbonate-based electrolyte, we identified fluoroethylene carbonate as a more desirable cyclic carbonate co-solvent than difluoroethylene carbonate for LMB due to its significantly higher ability to solvate lithium ions.

25 ENERGY STORAGE↗

Imaging the spin chirality of ferrimagnetic Néel skyrmions stabilized on topological antiferromagnetic Mn 3 Sn

Néel skyrmions are generally realized in asymmetric multilayers made of heavy metals (HMs) and ultrathin ferromagnets possessing strong interfacial Dzyaloshinskii-Moriya interactions (iDMIs). Depending on the relative strengths of iDMIs at the interfaces, various types of Néel skyrmions have been suggested, which are typified with characteristically different topological properties and current-driven dynamics. This suggests the importance of a precise quantification of their spin chiralities. In this paper, we explore the possibility of realizing Néel skyrmions in magnetic multilayers without the direct usage of standard HMs. Specifically, through depositing a thin layer of ferrimagnetic (FIM) CoTb layer on top of an antiferromagnetic (AFM) quantum material of composition Mn 3 Sn, the AFM exchange interaction at the asymmetric interface provides an equivalent iDMI for stabilizing FIM Néel skyrmions. Secondly, through using advanced four-dimensional Lorentz scanning transmission electron microscopy (4D LSTEM), in combination with x-ray magnetic circular dichroism photoemission electron microscopy (XMCD-PEEM), we can directly determine the spin chirality of FIM Néel skyrmions. Finally, the present findings not only broaden the phase space for chiral interfacial magnetism but also provide a possibility for future applications of heavy-metal-free skyrmionic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An extension of the localized artificial diffusivity method for immiscible and high density ratio flows

The localized artificial diffusivity (LAD) method is widely regarded as the preferred multi-material regularization scheme for the compact finite difference method, because it is conservative, easy to implement, and generally robust for a wide range of multi-material problems. However, traditional LAD methods face significant challenges when applied to flows with large density ratios and when maintaining thermodynamic equilibrium across material interfaces. These limitations arise from the formulation of the artificial diffusivity flux and the reliance on enthalpy diffusion for interface regularization. Additionally, traditional LAD methods struggle to ensure stability under large density ratio conditions, fail to maintain a finite interface thickness, and are therefore unsuitable for modeling immiscible interfaces. Here, in this work, we discuss the origins of these issues in traditional LAD methods and propose modifications which enable the simulation of large density ratio and immiscible flows. The proposed method targets the artificial diffusion fluxes at gradients and ringing in the volume fraction, rather than the mass fraction in traditional methods, to consistently regularize large density ratio interfaces. Furthermore, the proposed method introduces an artificial bulk density diffusion term to enforce equilibrium conditions across interfaces. To address the challenge of modeling immiscible flows, a conservative diffuse interface term is incorporated into the formulation to ensure a finite interface thickness. Specific consideration is taken in the design of the method to ensure that these crucial properties are maintained for N -material flows. The effectiveness of the proposed method is demonstrated through a series of canonical test cases, and its accuracy is validated by comparison with experimental data on micro-bubble collapse in water. These results highlight the method’s robustness and its ability to overcome the limitations of traditional LAD approaches.

Artificial diffusivity↗

Structure and Stability of Pristine and Carboxylate-Covered Anatase TiO 2 (001) in Aqueous Environment

The interactions of carboxylic acids and water with TiO 2 surfaces are important in applications ranging from solar cells to biomedical devices. Here we focus on the aqueous interface with the minority (001) surface of anatase TiO 2 (A-001) and the behavior of adsorbed formic and acetic acid monolayers at this interface. We investigated the structure and stability of the pristine reconstructed and formic/acetic acid covered A-001 surfaces in contact with water using density functional theory (DFT) calculations and ab initio molecular dynamics (AIMD) simulations. The (1 × 4) reconstruction of the pristine surface is found to be stable in aqueous environment, within the time scale of our simulation. Here, carboxylic acids adsorb in deprotonated bidentate (BD) form on A-001, with the dissociated proton transferred to a surface oxygen to form a bridging hydroxyl. Of the two possible configurations, BD bridging and BD straddling, of the adsorbed species, the latter is found to rapidly transform to a monodentate structure during our simulations. Further investigation of mixed acetate–formate monolayers on A-001 in water indicates that also BD bridging species can become unstable at the boundaries between formate and acetate-covered regions, transforming to a monodentate form that does not prevent water adsorption on the TiO 2 surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hybrid Lithium-Sulfur Batteries with an Advanced Gel Cathode and Stabilized Lithium-Metal Anode

The insulating nature of sulfur, polysulfide shuttle effect, and lithium metal deterioration cause a decrease in practical energy density and fast capacity fade in lithium-sulfur batteries. Here, we present an integrated strategy for the development of hybrid Li-S batteries based on a gel sulfur cathode, a solid electrolyte, and a protective anolyte composed of highly-concentrated salt electrolyte containing mixed additives. The dense solid electrolyte completely blocks polysulfide diffusion, and also makes it possible to investigate the cathode and anode independently. This gel cathode effectively traps the polysulfide active material while maintaining a low electrolyte to sulfur ratio (E/S) of 5.2 mL/g. The anolyte effectively protects the Li metal and suppresses the consumption of liquid electrolyte, enabling stable long-term cycling for over 700 hours in Li symmetric cells. This advanced design can simultaneously suppress the polysulfide shuttle, protect Li metal, and reduce the liquid electrolyte usage. The assembled hybrid batteries exhibit remarkably stable cycling performance over 300 cycles with high capacity. Finally, surface-sensitive techniques were carried out to directly visualize and to probe the interphase formed on the surface of the LAGP pellet, which may help stabilize the solid-liquid interface.

25 ENERGY STORAGE↗

Creep Resistance of Bulk Copper-Niobium Composites: an Inverse Effect of Multilayer Length Scale

We present that metallic multilayer systems show promising performance in extreme environments, with high stability of bi-metal interfaces down to nanometer length scales. The creep behavior of bulk, accumulative roll bonded (ARB) Copper-Niobium (Cu-Nb) composites has been studied at 400 °C as a function of layer thickness, ranging from 2μm to 65μm. Similar to single phase metallic systems, three regimes are observed during creep: transient, steady-state and tertiary. The mechanism controlling minimum creep rate for all conditions tested has a strong dependence on stress, consistent with dislocation-dominated creep. Additionally, unlike the conventional effect of grain size on creep resistance, this study reveals that decreasing length scale increases creep resistance.

36 MATERIALS SCIENCE↗

Atomic structures of interfacial solute gateways to θ' precipitates in Al-Cu alloys

Many materials employed in critical structural applications depend upon metastable strengthening precipitates that transform or dissolve at elevated temperatures. Herein, aberration-corrected scanning transmission electron microscopy and first-principles calculations are used to accurately determine the atomic structure of the highly mobile, semi-coherent precipitate interfaces that control this process in the classic θ' (Al 2 Cu) precipitate in the Al-Cu system. Semi-coherent {110} interfaces are found to be composed of an array of unexpected misfit dislocations that are arranged in two different structural units. Dislocations accommodate nearly all of the misfit between the Al matrix and strengthening phase. Cu is observed to segregate to the compressed edge of the dislocation cores at specific sites in this interface. First-principles calculations revealed the energetic landscape that facilitates these sites to become entry and exit gateways of Cu atoms in this semi-coherent interface. In conclusion, this investigation reveals critical features within semi-coherent interfaces that determine the thermal stability of precipitation-hardened alloys.

36 MATERIALS SCIENCE↗

Effect of grafting density on the two-dimensional assembly of nanoparticles

Employing grazing-incidence small-angle X-ray scattering (GISAXS) and X-ray reflectivity (XRR), we demonstrate that films composed of polyethylene glycol (PEG)-grafted silver nanoparticles (AgNPs) and gold nanoparticles (AuNPs), as well as their binary mixtures, form highly stable hexagonal structures at the vapor–liquid interface. These nanoparticles exhibit remarkable stability under varying environmental conditions, including changes in pH, mixing concentration, and PEG chain length. Short-chain PEG grafting produces dense, well-ordered films, while longer chains produce more complex, less dense quasi-bilayer structures. AuNPs exhibit higher grafting densities than AgNPs, leading to more ordered in-plane arrangements. In binary mixtures, AuNPs dominate the population at the surface, while AgNPs integrate into the system, expanding the lattice without forming a distinct binary superstructure. In conclusion, these results offer valuable insights into the structural behavior of PEG-grafted nanoparticles and provide a foundation for optimizing binary nanoparticle assemblies for advanced nanotechnology applications.

36 MATERIALS SCIENCE↗

Crystal structure of the kinase and UBA domains of SNRK reveals a distinct UBA binding mode in the AMPK family

Highlights: • The UBA domain of SNRK binds between the N- and C-lobes of the kinase domain. • The UBA binding mode in SNRK is similar to yet different from AMPK. • Structural analyses suggested an inhibitory function of SNRK UBA domain. Sucrose non-fermenting (Snf1)-related kinase (SNRK) is a novel member of the AMP-activated protein kinase (AMPK) family and is involved in many metabolic processes. Here we report the crystal structure of an N-terminal SNRK fragment containing kinase and adjacent ubiquitin-associated (UBA) domains. This structure shows that the UBA domain binds between the N- and C-lobes of the kinase domain. The mode of UBA binding in SNRK largely resembles that in AMPK and brain specific kinase (BRSK), however, unique interactions play vital roles in stabilizing the KD-UBA interface of SNRK. We further propose a potential role of the UBA domain in the regulation of SNRK kinase activity. This study provides new insights into the structural diversities of the AMPK kinase family.

60 APPLIED LIFE SCIENCES↗

A robust and efficient finite volume method for compressible inviscid and viscous two-phase flows [A robust and efficient finite volume method for compressible viscous two-phase flows]

A robust and efficient density-based finite volume method is developed for solving the six-equation single pressure system of two-phase flows at all speeds on hybrid unstructured grids. Unlike conventional approaches where an expensive exact Riemann solver is normally required for computing numerical fluxes at the two-phase interfaces in addition to AUSM-type fluxes for single-phase interfaces in order to maintain stability and robustness in cases involving interactions of strong pressure and void-fraction discontinuities, a volume-fraction coupling term for the AUSM + -up fluxes is introduced in this work to impart the required robustness without the need of the exact Riemann solver. The resulting method is significantly less expensive in regions where otherwise the Riemann solver would be invoked. A transformation from conservative variables to primitive variables is presented and the primitive variables are then solved in the implicit method in order for the current finite volume method to be able to solve, effectively and efficiently, low Mach number flows in traditional multiphase applications, which otherwise is a great challenge for the standard density-based algorithms. Here, a number of benchmark test cases are presented to assess the performance and robustness of the developed finite volume method for both inviscid and viscous two-phase flow problems. The numerical results indicate that the current density-based method provides an attractive and viable alternative to its pressure-based counterpart for compressible two-phase flows at all speeds.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Atomic Collision and Ionization Effects in Oxides

Irradiation with ions and electrons provides accelerated study of radiation damage in nuclear materials, such as those proposed for immobilization of actinides and long-lived fission products. The effects of ion irradiation in SrTiO3, Sm2Ti2O7 and Sr2Nd8(SiO4)6O2, as representative materials, are studied using 1 MeV Au+ ions. The irradiation-induced disorder, due to atomic collisions processes, increases nonlinearly with irradiation dose and is well described by a disorder accumulation model that includes contributions from amorphous domains, point defects and defect clusters. Ionization from 200 keV electrons induces recrystallization at the amorphous/crystalline (a/c) interface that exhibits several distinct stages associated with residual defect annihilation near the interface, epitaxial regrowth at the interface, and a surface-stabilized amorphous state. Understanding ionization effects and the coupled effects of electronic and atomic dynamics on material behavior is a challenging area for scientific research.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Mitigating ion migration in perovskite solar cells

The intrinsic ion migration in the metal halide perovskite absorber layer and its interfaces seriously limits the device stability of perovskite solar cells (PSCs). Despite considerable efforts to mitigate the ion migration issue, it remains a formidable challenge in the commercialization of PSCs. In this paper, we provide a short review of the device failure mechanisms induced by intrinsic ion migration and discuss the detrimental effects of ion migration on different component layers of PSCs. We outline the corresponding strategies to mitigate ion migration in PSCs and provide an insight on materials engineering to attain long-term stabilized perovskite photovoltaics.

14 SOLAR ENERGY↗

Rapid High-Resolution Analysis of Polysaccharide-Lignin Interactions in Secondary Plant Cell Walls Using Proton-Detected Solid-State NMR

The plant secondary cell wall, a complex matrix composed of cellulose, hemicellulose, and lignin, is crucial for the mechanical strength and water-proofing properties of plant tissues, and serves as a primary source of biomass for biorenewable energy and biomaterials. Structural analysis of these polymers and their interactions within the secondary cell wall has been heavily relying on 13 C-based solid-state NMR techniques. In this study, we explore the application of 1 H-detected solid-state NMR techniques for rapid, high-resolution structural characterization of polysaccharides and lignin, demonstrated on the stems of hardwood eucalyptus. We explored the use of synthesized 2D spectra to resolve central 1 H resonances and the combined application of 3D hCCH and hCHH experiments for complete resonance assignment and unambiguous identification of lignin-carbohydrate interactions. Our findings emphasize the central role of acetylated three-fold xylan conformers, rather than two-fold, in stabilizing the carbohydrate-lignin interface, with glucuronic acid sidechains in eucalyptus glucuronoxylan colocalizing with lignin, revised cellulose-lignin interactions involving uncoated microfibril surfaces, and pectin-lignin interactions indicative of early-stage lignification. These results present a novel approach for rapid structural analysis of lignocellulosic biomaterials without the need for solubilization or extraction.

09 BIOMASS FUELS↗

Conformational Dynamics of AcrA Govern Multidrug Efflux Pump Assembly

Multidrug efflux pumps of pathogenic, Gram-negative bacteria comprise an innate resistance mechanism and are key contributors to the emerging global pandemic of antibiotic resistance. Several increasingly detailed cryo-electron microscopy maps have been resolved of an entire efflux pump complex, AcrAB–TolC, resulting in atomistic structural models. Using a recent model, we have carried out nearly 40 μs of molecular dynamics simulations to study one of the key components of the protein complex AcrA, the membrane fusion protein that connects the inner-membrane-bound AcrB to the outer-membrane-bound TolC. Here, we determined a three-dimensional potential of mean force (PMF) for AcrA, which displays two main conformational basins representing assembly competent and incompetent states. Corresponding experiments show that stabilizing mutations at an interdomain interface shift the dynamic equilibrium between these states to the incompetent one, disrupting pump assembly and function and resensitizing bacteria to existing antibiotics. The modulation of AcrA dynamics through pharmacological intervention therefore presents a promising route for the development of new antibiotics.

59 BASIC BIOLOGICAL SCIENCES↗