Effects of compliance and plasticity on interfacial failure in thin film structures.
No abstract prepared.
36 MATERIALS SCIENCE↗
SEARCH · Search NASA
Results for “interfacial structures”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Very High Efficiency, Hybrid Organic-Inorganic Photovoltaic Cells
This SETP project focuses on developing highly efficient, hybrid organic inorganic photovoltaic (OIPV) cells. The goal is to greatly enhance the power conversion efficiency of hybrid OIPV cells using several innovative approaches. The specific objectives are: (i) to develop new inorganic nanocrystals along with conjugated oligomers and polymers to improve their matching with the solar spectrum; (ii) to engineer the interfacial electronic structures at the hybrid interface to minimize energy and carrier losses during charge transfer; (iii) to understand the assembly of hybrid polymer/nanorod composites and demonstrate hybrid nanostructures that facilitate carrier transport and collection; and (iv) to demonstrate high efficiency hybrid OIPV cells by effectively incorporating materials absorbing in different spectral regions. Through this project, the research team at the University of Florida synthesized a series of new functional organic materials and colloidal nanocrystals with optical absorption covering the near-ultraviolet, visible, and near-infrared regions of the solar spectrum. The team also demonstrated improved understandings on how to control the morphological structure of the organic/inorganic hybrid active layer as well as on the orientation of anisotropic nanostructures in the organic matrix. With the demonstration of several innovative device structures, the efficiency of such hybrid photovoltaic cells was drastically increased. The introduction of proper chemical treatment of the nanocrystal/organic interface and the demonstration of a new light trapping technique (which can also be easily scaled up for large area device fabrication) also contributed to the significant increase in device efficiency. The new knowledge on material synthesis, material processing, device physics, and optical design gained from this project will greatly contribute to the further development of this low-cost PV technology.
14 SOLAR ENERGY↗
Soft X-ray Spectroscopy of C60/Copper Phthalocyanine/MoO3 Interfaces: Role of Reduced MoO3 on Energetic Band Alignment and Improved Performance
The interfacial electronic structure of C{sub 60}/copper phthalocyanine (CuPc)/molybdenum trioxide (MoO{sub 3}) thin films grown in situ on indium tin oxide (ITO) substrates has been studied using synchrotron radiation-excited photoelectron spectroscopy in an attempt to understand the influence of oxide interlayers on the performance of small molecule organic photovoltaic devices. The MoO{sub 3} layer on ITO is found to significantly increase the work function of the substrate and induces large interface dipoles and band bending at the CuPc/MoO{sub 3} interface. The large band bending confirms the formation of an internal potential that assists hole extraction from the CuPc layer to the electrode. The electronic structure of the MoO{sub 3} layer on ITO was also examined using various soft X-ray spectroscopies to probe the conductive nature of the MoO{sub 3} thin film.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Applications of electronic structure and atomistic models to interfacial problems in catalysis and corrosion
Abstract Not Provided
36 MATERIALS SCIENCE↗
Revealing the structure and composition of small interfacial volumes composed within reactive multilayer thin films.
Abstract not provided.
Adams, David Price↗
Interfacial bonding oxides for glass-ceramic-to-metal seals
The present invention relates to structure including an interfacial seal between a glass-ceramic component and a metal component, as well as methods for forming such structures. In particular embodiments, the interfacial seal includes a metal oxide. Such interfacial seals can be beneficial for, e.g., hermetic seals between a glass-ceramic component and a metal component.
36 MATERIALS SCIENCE↗
Interfacial bonding oxides for glass-ceramic-to-metal seals
The present invention relates to structure including an interfacial seal between a glass-ceramic component and a metal component, as well as methods for forming such structures. In particular embodiments, the interfacial seal includes a metal oxide. Such interfacial seals can be beneficial for, e.g., hermetic seals between a glass-ceramic component and a metal component.
Dai, Steve Xunhu↗
The roles of oxygen non-stoichiometry on the electrochemical properties of oxide-based cathode materials
Not Available
Zheng, Jianming↗
Mn(II) oxidation catalyzed by nanohematite surfaces and manganite/hausmannite core-shell nanowire formation by self-catalytic reaction
The present study investigated the solid products of heterogeneous catalytic oxidation of aqueous Mn(II) by O2 in the presence of hematite nanoparticles (NPs) using transmission electron microscopy (TEM), scanning TEM (STEM), and electron energy-loss spectroscopy (EELS). The oxidation experiments were conducted at room temperature (22±2?) in solutions containing 10-3 M Mn(II) at pH 7.5 in the dark. During 48 hours of reaction, a single-phase manganite (a Mn oxyhydroxide) nanowire was formed by way of metastable groutite and feitknechtite nanowires, both of which are polymorphs of manganite. Between 48 and 168 hours, the manganite further altered to core-shell structured nanowires with hausmannite (a mixed valent Mn oxide) forming a very thin (2 nm) outer-shell on the manganite wire core. The formation of Mn-oxyhydroxide nanowires was catalyzed by the hematite NPs surface through electrochemical pathways. This is described via the electron transfer across a redox couple from adsorbed Mn(II) to another site with adsorbed O2 via the band structure of the semiconducting hematite. On the other hand, the Ostwald step rule was operative in the sequential crystallization from metastable groutite and feitknechtite to stable manganite, which could have resulted from the differences in the surface free energies, sizes, and morphologies of product polymorphs at the nanoscale. The final product (at least in the time range of our experiments) exhibited manganite/hausmannite core-shell structures. This product is most likely to be formed by the reactions catalyzed by the manganite nanowires themselves. Microscopic investigation of interfacial changes in structure and chemistry at the nanoscale is key, and it can be essential to understand the kinetic and thermodynamic phenomena related to the redox chemistry and phase stability of nanoparticles in complex, heterogeneous systems such as natural environments.
Inoue, Sayako↗
THz emission from Co/Pt bilayers with varied roughness, crystal structure, and interface intermixing
Ultrafast demagnetization of Co/Pt heterostructures induced by a femtosecond 800-nm laser pulse launches a spin current from Co to Pt and subsequent conversion of the spin current to a charge current in the Pt layer due to the inverse spin-Hall effect. At the same time, due to the spin-dependent photogalvanic effect, a circularly polarized femtosecond laser pulse also generates a photocurrent at the Co/Pt interface. Both ultrashort photocurrent pulses are effectively detected in a contactless way by measuring the THz radiation they emit. Here we aim to understand how the properties of the Co/Pt interface affect the photocurrents in the bilayers. By varying the interfacial roughness, crystal structure, and interfacial intermixing, as well as having an explicit focus on the cases when THz emissions from these two photocurrents reveal opposite trends, we identify which interface properties play a crucial role for the photocurrents. In particular, we show that by reducing the roughness, the THz emission due to the spin-dependent photogalvanic effect reduces to zero while the strength of the THz emission from the photocurrent associated with the inverse spin-Hall effect increases by a factor of 2. On the other hand, while intermixing strongly enhances the THz emission from the inverse spin-Hall effect by a factor of 4.2, THz emission related to the spin-dependent photogalvanic effect reveals the opposite trend. Furthermore, these findings indicate that microstructural properties of the Co-Pt interface play a decisive role in the generation of photocurrents.
36 MATERIALS SCIENCE↗
Dual material fused filament fabrication of composite core‐shell structures with improved impact resistance and interfacial adhesion
The mechanical performance of parts produced by fused filament fabrication (FFF) has been limited due to the presence of voids and poor interlayer welding. Recent advancements in FFF have enabled the fabrication of void-free objects with strong interlayer welding through the use of semicrystalline polymer shells such as high-density polyethylene (HDPE) along with a high viscosity core polymer like acrylonitrile-butadiene-styrene (ABS). Furthermore, the zero-shear viscosity (η0) of ABS is three orders of magnitude higher than HDPE making the ABS-HDPE core-shell configuration preferable. ABS holds the shape by preventing bulk flow and part bending while HDPE promotes full surface contact across the layers. Most polymers, however, are immiscible which causes a weak weld line along the core-shell interface. Herein, maleic anhydride (MAH) is grafted to the butadiene segment of the ABS core thereby compatibilizing the interface with HDPE, improving the interfacial adhesion. Attenuated total reflectance-Fourier transform infrared spectroscopy was employed to confirm successful grafting. Using a custom-made die affording the core-shell structure, the ABS-g-MAH is shown to improve the impact resistance by 253% and 16% compared to neat HDPE and ABS specimens, respectively. Additionally, a 10% increase compared to the unmodified ABS-HDPE core-shell configuration is observed.
36 MATERIALS SCIENCE↗
Amorphous oxide alloys as interfacial layers with broadly tunable electronic structures for organic photovoltaic cells
In diverse classes of organic optoelectronic devices, controlling charge injection, extraction, and blocking across organic semiconductor– inorganic electrode interfaces is crucial for enhancing quantum efficiency and output voltage. To this end, the strategy of inserting engineered interfacial layers (IFLs) between electrical contacts and organic semiconductors has significantly advanced organic light-emitting diode and organic thin film transistor performance. For organic photovoltaic (OPV) devices, an electronically flexible IFL design strategy to incrementally tune energy level matching between the inorganic electrode system and the organic photoactive components without varying the surface chemistry would permit OPV cells to adapt to ever-changing generations of photoactive materials. Here we report the implementation of chemically/environmentally robust, low-temperature solution-processed amorphous transparent semiconducting oxide alloys, In-Ga-O and Ga-Zn-Sn-O, as IFLs for inverted OPVs. Lastly, continuous variation of the IFL compositions tunes the conduction band minima over a broad range, affording optimized OPV power conversion efficiencies for multiple classes of organic active layer materials and establishing clear correlations between IFL/photoactive layer energetics and device performance.
25 ENERGY STORAGE↗
Effect of transport mechanism on the coarsening of bicontinuous structures: A comparison between bulk and surface diffusion
Here, coarsening of bicontinuous microstructures is observed in a variety of systems, such as nanoporous metals and mixtures that have undergone spinodal decomposition. To better understand the morphological evolution of these structures during coarsening, we compare the morphologies resulting from two different coarsening mechanisms, surface and bulk diffusion. We perform phase-field simulations of coarsening via each mechanism in a two-phase mixture at nominal volume fractions of 50%-50% and 36%-64%, and the simulated structures are characterized in terms of topology (genus density), the interfacial shape distribution, structure factor, and autocorrelations of phase and mean curvature. We observe self-similar evolution of morphology and topology and agreement with the expected power laws for dynamic scaling, in which the characteristic length scale increases over time proportionally to t 1/4 for surface diffusion and t 1/3 for bulk diffusion. While we observe the expected difference in the coarsening kinetics, we find that differences in self-similar morphology due to coarsening mechanism are relatively small, although typically they are larger at 36% volume fraction than at 50% volume fraction. In particular, we find that bicontinuous structures coarsened via surface diffusion have lower scaled genus densities than structures coarsened via bulk diffusion. We also compare the self-similar morphologies to those in literature and to two model bicontinuous structures, namely, constant-mean-curvature surfaces based on the Schoen G minimal surface and random leveled-wave structures. The average scaled mean curvatures of these model structures agree reasonably with those of the coarsened structures at both 36% and 50%, but we find substantial disagreements in the scaled genus densities and the standard deviations of mean curvature.
36 MATERIALS SCIENCE↗
Density functional theory for carbon dioxide crystal
We present a density functional approach to describe the solid−liquid phase transition, interfacial and crystal structure, and properties of polyatomic CO{sub 2}. Unlike previous phase field crystal model or density functional theory, which are derived from the second order direct correlation function, the present density functional approach is based on the fundamental measure theory for hard-sphere repulsion in solid. More importantly, the contributions of enthalpic interactions due to the dispersive attractions and of entropic interactions arising from the molecular architecture are integrated in the density functional model. Using the theoretical model, the predicted liquid and solid densities of CO{sub 2} at equilibrium triple point are in good agreement with the experimental values. Based on the structure of crystal-liquid interfaces in different planes, the corresponding interfacial tensions are predicted. Their respective accuracies need to be tested.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Preparation, characterization, and infrared emissivity property of optically active polyurethane/TiO{sub 2}/SiO{sub 2} multilayered microspheres
Optically active polyurethane/titania/silica (LPU/TiO{sub 2}/SiO{sub 2}) multilayered core-shell composite microspheres were prepared by the combination of titania deposition on the surface of silica spheres and subsequent polymer grafting. LPU/TiO{sub 2}/SiO{sub 2} was characterized by FT-IR, UV-vis spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), SEM and TEM, and the infrared emissivity value (8-14 {mu}m) was investigated in addition. The results indicated that titania and polyurethane had been successfully coated onto the surfaces of silica microspheres. LPU/TiO{sub 2}/SiO{sub 2} exhibited clearly multilayered core-shell construction. The infrared emissivity values reduced along with the increase of covering layers thus proved that the interfacial interactions had direct influence on the infrared emissivity. Besides, LPU/TiO{sub 2}/SiO{sub 2} multilayered microspheres based on the optically active polyurethane took advantages of the orderly secondary structure and strengthened interfacial synergistic actions. Consequently, it possessed the lowest infrared emissivity value. - Graphical Abstract: Optically active polyurethane/titania/silica (LPU/TiO{sub 2}/SiO{sub 2}) multilayered core-shell composite microspheres were prepared by the combination of titania deposition on the surface of silica spheres and subsequent polymer grafting. Highlights: > Optically active polyurethane based on tyrosine was used for the modification of nanoparticles. > LPU/TiO{sub 2}/SiO{sub 2} multilayered core-shell microspheres were prepared and characterized. > Interfacial interactions and secondary structure affected the infrared emissivity of composite.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Effect of interfacial interactions on the thermal conductivity and interfacial thermal conductance in tungsten–graphene layered structure
Graphene film was deposited by microwave plasma assisted deposition on polished oxygen free high conductivity copper foils. Tungsten–graphene layered film was formed by deposition of tungsten film by magnetron sputtering on the graphene covered copper foils. Tungsten film was also deposited directly on copper foil without graphene as the intermediate film. The tungsten–graphene–copper samples were heated at different temperatures up to 900 °C in argon atmosphere to form an interfacial tungsten carbide film. Tungsten film deposited on thicker graphene platelets dispersed on silicon wafer was also heated at 900 °C to identify the formation of tungsten carbide film by reaction of tungsten with graphene platelets. The films were characterized by scanning electron microscopy, Raman spectroscopy, and x-ray diffraction. It was found that tungsten carbide film formed at the interface upon heating only above 650 °C. Transient thermoreflectance signal from the tungsten film surface on the samples was collected and modeled using one-dimensional heat equation. The experimental and modeled results showed that the presence of graphene at the interface reduced the cross-plane effective thermal conductivity and the interfacial thermal conductance of the layer structure. Heating at 650 and 900 °C in argon further reduced the cross-plane thermal conductivity and interface thermal conductance as a result of formation nanocrystalline tungsten carbide at the interface leading to separation and formation of voids. The present results emphasize that interfacial interactions between graphene and carbide forming bcc and hcp elements will reduce the cross-plane effective thermal conductivity in composites.
36 MATERIALS SCIENCE↗
Steering Molecular Dynamics Simulations of Membrane-Associated Proteins with Neutron Reflection Results
Herein, we present a novel method to incorporate structural results from surface-sensitive scattering, such as X-ray or neutron reflectometry, into molecular dynamics simulations. While reflectometry techniques generally provide a means to determine the molecular-scale structures of organized interfacial films, they were recently shown to offer the capability to characterize the structures of protein-membrane complexes supported by a solid substrate. One-dimensional information inherent in the experimental results is used in the form of component volume occupancy (CVO) profiles, which describe the distribution of molecular components within an interfacial architecture, to construct real-space constraints in the form of a biasing potential for the simulation that vanishes when the simulated and experimental profiles agree. This approach improves the correspondence between simulation and experiment, as shown in the re-evaluation of an neutron-reflection-derived structure which was approximated by an independent molecular dynamics simulation in earlier work, and it also leads to faster equilibration of ensemble structures. We further show that time averaging the CVO profile that develops in the simulation while biasing with this approach permits fluctuations about the average that are necessary for conformational exploration of the system. This method is particularly valuable for studies of proteins at interfaces that contain disordered regions since the conformation of such regions is difficult to judge from the analysis of one-dimensional experimental profiles and may take prohibitively long to equilibrate in simulations.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Electronic structure modulation of MoS2 by substitutional Se incorporation and interfacial MoO3 hybridization: Implications of Fermi engineering for electrocatalytic hydrogen evolution and oxygen evolution
The design of earth-abundant electrocatalysts that can facilitate water splitting at low overpotentials, provide high current densities, and enable prolonged operational lifetimes is central to the production of sustainable fuels. The distinctive atomistic and electronic structure characteristics of the edges of MoS2 imbue high reactivity toward the hydrogen evolution reaction. MoS2 is nevertheless characterized by significantly high overpotentials as compared to platinum. Here, we demonstrate that modulation of the electronic structure of MoS2 through interfacial hybridization with MoO3 and alloying of selenium on the anion sublattice allows for systematic lowering of the conduction band edge and raising of the valence band edge, respectively. The former promotes enhanced electrocatalytic activity toward hydrogen evolution, whereas the latter promotes enhanced activity toward the oxygen evolution reaction. Such alloyed heterostructures prepared by sol-gel reactions and hydrothermal selenization expose a high density of edge sites. The alloyed heterostructures exhibit low overpotential, high current density, high turnover frequency, and prolonged operational lifetime. The mechanistic origins of catalytic activity have been established based on electronic structure calculations and x-ray absorption and emission spectroscopy probes of electronic structure, which suggest that interfacial hybridization at the MoO3 interface yields low-lying conduction band states that facilitate hydrogen adsorption. In contrast, shallow Se 4p-derived states give rise to a raised effective valence band maximum, which facilitates adsorption of oxygen intermediates and engenders a low overpotential for the oxygen evolution reaction. The findings illustrate the use of electronic structure modulation through interfacial hybridization and alloying to systematically improve electrocatalytic activity.
Parija, Abhishek↗