Search NASA⌕ Search

SEARCH · Search NASA

Results for “structured model reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Experiments on near-wall structure of three-dimensional boundary layers

Investigations of three-dimensional turbulent boundary layers have shown basic differences between two- and three-dimensional flows. These differences can significantly impact the modeling of three-dimensional flows since many flow models are based on results from two-dimensional boundary layers. In many cases the shear stress vector direction has been shown to lag relative to the direction of the mean velocity gradient as the cross flow grows downstream. Coincidence of these vectors is necessary for a scalar eddy viscosity modeling assumption. A second effect is a reduction in magnitude of the shear stress and/or the shear stress to turbulence energy ratio, a(sub 1). This reduction has been observed in several experiments. Recent numerical simulations also indicate wall-layer structural differences between two- and three-dimensional boundary layers. The differences in structure between two- and three-dimensional boundary layers was also addressed in the experiment of Littell & Eaton. The experiment used two-point correlations to investigate the vortical structures in a three dimensional boundary layer on a spinning disk. It was found that each sign of longitudinal vortex is equally likely to exist, but one sign of vorticity is associated with a structure which is better at producing ejections. The goal of the current investigation is to study the structure of the inner layers. Among other questions, the differences between the effects deduced from the three-dimensional flow simulations and the effects seen in experiments can be examined. The research concentrates on the structure of the wall-layer through flow visualization and direct turbulence measurements down to y(+) = 5.

Flack, Karen A.↗
NASA NTRS1989

Structural modeling for control design (articulated multibody component representation)

High gain, high frequency flexible responses in gimbaled multibody systems are discussed. Their origin and physical significance are described in terms of detailed mass and stiffness modeling at actuator/sensor interfaces. Guyan Reduction, Generalized Dynamic Reduction, inadequate mass modeling detail, as well as system mode truncation, are shown to suppress the high gain high frequency response and thereby lose system flexibility important for stability and performance predictions. Model validation by modal survey testing is shown to risk similar loss of accuracy. Difficulties caused by high frequency responses in component mode simulations, such as DISCOS, and also linearized system mode simulations, are described, and approaches for handling these difficulties are discussed.

Haugse, E. D.↗
DOE OSTI2025

Denoising Autoencoder for Reconstructing Sensor Observation Data and Predicting Evapotranspiration: Noisy and Missing Values Repair and Uncertainty Quantification

Abstract Machine learning (ML) methods applied in scientific research often deal with interrelated features in high‐dimensional data. Reducing data noise and redundancy is needed to increase prediction accuracy and efficiency especially when dealing with data from field sensors. We explored an unsupervised learning method, the denoising autoencoder (DAE), to extract the underlying data structure from noisy raw data in the context of predicting hydrologic quantities from multiple field sensors. These sensors have intrinsic instrumental noise and occasional malfunctions that cause missing values. Our DAE neural network reconstructed meteorological sensor data containing noise and missing values to predict evapotranspiration in a mountainous watershed. The DAE reconstructed the sensor variables with a mean coefficient of determination value of 0.77 across 15 dimensions representing individual sensors. It reduced variance and bias uncertainties compared to a classical autoencoder model. The reconstruction quality varied across dimensions depending on their cross‐correlation and alignment with the underlying data structure. Uncertainties arising from the model structure were overall higher than those resulting from data corruption. We attached the DAE structure to a downstream ET‐prediction neural network in three formats and achieved reasonably accurate ET predictions . The use of the DAE notably reduced variance uncertainty in ET prediction. However, excessive variance reduction may be accompanied by an increase in bias due to the intrinsic bias‐variance tradeoff. Our method of evaluating and reducing uncertainties in aggregated data from different sources can be used to improve predictive models, process understanding, and uncertainty quantification for better water resource management. Plain Language Summary We present a machine learning method, namely the denoising autoencoder, which reduces the effects of data noise and missing values typically present in scientific data sets collected through sensor measurements. This method selects the most relevant information from noisy raw data collected by the instruments and fills in missing values. To demonstrate the effectiveness of our method, we applied it to predict evapotranspiration, a hydrologic variable that represents the water moved from the land surface to the atmosphere through a combination of evaporation and plant water use (transpiration). We also used a random sampling technique (the Monte Carlo method) to compare the uncertainty in the predictions when using the raw and noisy data versus the reconstructed data. The denoising process produced more accurate predictions of evapotranspiration with less uncertainty. Improved predictions of evapotranspiration can lead to a better understanding and accounting of water budgets. This ML approach is broadly suitable for a wide variety of applications that involve noisy sensor data with missing values. Key Points We used a denoising autoencoder (DAE) neural network to reduce noise in meteorological and soil sensor observations by on average We used Monte Carlo sampling to estimate the bias and variance of all model outputs, including uncertainty sources from data and the model We attached the DAE component to a downstream neural network to predict ET with the variance reduced by , compared to that without the DAE

denoising autoencoder↗
DOE OSTI2021

Coupling of regional geophysics and local soil-structure models in the EQSIM fault-to-structure earthquake simulation framework

Accurate understanding and quantification of the risk to critical infrastructure posed by future large earthquakes continues to be a very challenging problem. Earthquake phenomena are quite complex and traditional approaches to predicting ground motions for future earthquake events have historically been empirically based whereby measured ground motion data from historical earthquakes are homogenized into a common data set and the ground motions for future postulated earthquakes are probabilistically derived based on the historical observations. This procedure has recognized significant limitations, principally due to the fact that earthquake ground motions tend to be dictated by the particular earthquake fault rupture and geologic conditions at a given site and are thus very site-specific. Historical earthquakes recorded at different locations are often only marginally representative. There has been strong and increasing interest in utilizing large-scale, physics-based regional simulations to advance the ability to accurately predict ground motions and associated infrastructure response. However, the computational requirements for simulations at frequencies of engineering interest have proven a major barrier to employing regional scale simulations. In a U.S. Department of Energy Exascale Computing Initiative project, the EQSIM application development is underway to create a framework for fault-to-structure simulations. This framework is being prepared to exploit emerging exascale platforms in order to overcome computational limitations. This article presents the essential methodology and computational workflow employed in EQSIM to couple regional-scale geophysics models with local soil-structure models to achieve a fully integrated, complete fault-to-structure simulation framework. Here, the computational workflow, accuracy and performance of the coupling methodology are illustrated through example fault-to-structure simulations.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Elucidating CO Oxidation Pathways on Rh Atoms and Clusters on the “29” Cu 2 O/Cu(111) Surface

We report single-atom catalysts have attracted a great deal of attention due to their distinct reactivity and potential for cost savings. However, despite the wealth of literature in recent years, identifying the exact nature of the active sites and associated reaction mechanisms remains challenging in many cases. Herein, we take a surface science approach to understand how Rh single atoms and small clusters behave on the thin film “29” Cu 2 O grown on Cu(111). We find that in contrast to Pt, which is present solely as single atoms on the “29” Cu 2 O surface, Rh atoms and clusters coexist and each enable low-temperature CO oxidation, but via different pathways. Specifically, the single Rh atoms produce CO 2 at 444 K via a Mars van Krevelen mechanism whereas the Rh clusters can also dissociate CO, as demonstrated via isotope labeling, and liberate CO 2 at 313 K. Density functional theory (DFT) calculations quantify the energetics of these different pathways and demonstrate that only extended Rh is capable of CO dissociation. Low-temperature scanning tunneling microscopy (STM) reveals that unlike Pt atoms on the same surface, which stay atomically dispersed, the distribution of Rh structures is dependent on pretreatment conditions. DFT calculations reveal the greater tendency of Rh atoms to cluster than Pt, and STM image simulations confirm the active sites. Ambient pressure X-ray photoelectron spectroscopy studies on the same single crystal model systems demonstrate that 1% of a monolayer of Rh on the “29” Cu 2 O thin film significantly accelerates its reduction by CO at 400 K, thus confirming the ultrahigh vacuum surface science findings. Together, these results illustrate how well-defined single crystal experiments are useful in building structure–function relationships that elucidate the reactivity of different ensemble sizes with a level of detail beyond what is possible with high surface area catalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Effect of aerosols and NO 2 concentration on ultraviolet actinic flux near Mexico City during MILAGRO: measurements and model calculations

Ultraviolet (UV) actinic fluxes (AF) measured with three Scanning Actinic Flux Spectroradiometers (SAFS) are compared with the Tropospheric Ultraviolet-Visible (TUV) model v.5 in order to assess the effects of aerosols and NO 2 concentrations on the radiation. Measurements were made during the MILAGRO campaign near Mexico City in March 2006, at a ground-based station near Mexico City (the T1 supersite) and from the NSF/NCAR C-130 aircraft. At the surface, measurements are typically smaller by up to 25 % in the morning, 10% at noon, and 40% in the afternoon, than actinic flux modeled for clean, cloud-free conditions. When measurements of PBL height, NO 2 concentration and aerosols optical properties are included in the model, the agreement improves to within ±10% in the morning and afternoon, and ±3% at noon. Based on daily averages, aerosols account for 68%, NO 2 for 25%, and residual uncertainties for 7% of these AF reductions observed at the surface. Several overpasses from the C-130 aircraft provided the opportunity to examine the actinic flux perturbations aloft, and also show better agreement with the model when aerosol and NO 2 effects are included above and below the flight altitude. TUV model simulations show that the vertical structure of the actinic flux is sensitive to the choice of the aerosol single scattering albedo (SSA) at UV wavelengths. Typically, aerosols caused enhanced AF above the PBL and reduced AF near the surface. However, for highly scattering aerosols (SSA > 0.95), enhancements can penetrate well into the PBL, while for strongly absorbing aerosols (SSA<0.7) reductions in AF are computed in the free troposphere as well as in the PBL. Finally, additional measurements of the SSA at these wavelengths are needed to better constrain the effect of aerosols on the vertical structure of the actinic flux.

Palancar, G. G.↗
NASA NTRS1983

cD galaxy dynamics and an aged ridge (jet) in 3C 338

The results of VLA observations and possible models for the peculiar structure of 3C 338, a two-arcmin radio source associated with the cD galaxy NGC 6166 in Abell 2199, are presented. The optical parameters for Abell 2199 and NGc 6166 are reviewed, and the VLA observations and reductions are described. The radio structure of 3C 338 including spectral index and polarization distributions are also discussed. Two possible origins for the ridge structure located to the south of the core which has some characteristics of a jet are proposed. The first involves a cooling accretion flow of ICM material onto the cD. The ram pressure of a highly asymmetric flow seems to be sufficient to confine the radio ridge using an accretion rate of 100 solar masses/yr. The second model presumes that the ridge is actually an aged radio jet. The radio engine would have to be intermittent with a period of about ten million years.

White, R. A.↗
NASA NTRS1988

Control of the induced microgravity environment of the Man Tended Free Flyer (MTFF)

Induced disturbance sources have been identified on board the Man Tended Free Flyer (MTFF). Vibration responses at sensitive payload/spacecraft interfaces have been predicted by the application of an empirically found spacecraft dynamic transfer function. Vibrations from fluid loops (Freon, water) and of reaction wheels are assessed to be the main contributors to the induced microgravity environment. The expected payload acceleration response amplitudes presented here are more than one hundred times higher than the admissible values given by the MTFF system requirement, not considering the structural striction-friction effects which could be avoided by appropriate design. Real responses will be significantly lower because the derivation of excitation and transmission functions are based on worst case assumptions. The results indicate that future activities must be concentrated on equipment design improvement and the implementation of vibration reduction along the disturbance transmission path. The activities must be accompanied by early equipment and assembly development tests and transmissibility measurements with the integrated spacecraft engineering and structural models in order to improve the accuracy of payload response predictions.

Schlund, Juergen↗
NASA NTRS1991

Analysis and correlation of SA349/2 helicopter vibration

Helicopter airframe vibration is examined using calculation and measurements for the SA349/2 research helicopter. The hub loads, which transmit excitation to the fuselage, are predicted using a comprehensive rotorcraft analysis and correlated with measured hub loads. The predicted and measured hub loads are then coupled with finite element models representing the SA349/2 fuselage. The resulting vertical acceleration at the pilot seat is examined. Adjustments are made to the airframe structural models to examine the sensitivity of predicted vertical acceleration to the model. Changes of a few percent to the damping and frequency of specific modes lead to large reductions in predicted vibration and to major improvements in the correlations with measured pilot seat vertical acceleration.

Heffernan, Ruth↗
NASA NTRS1991

Parallelized solvers for heat conduction formulations

Based on multilevel partitioning, this paper develops a structural parallelizable solution methodology that enables a significant reduction in computational effort and memory requirements for very large scale linear and nonlinear steady and transient thermal (heat conduction) models. Due to the generality of the formulation of the scheme, both finite element and finite difference simulations can be treated. Diverse model topologies can thus be handled, including both simply and multiply connected (branched/perforated) geometries. To verify the methodology, analytical and numerical benchmark trends are verified in both sequential and parallel computer environments.

Padovan, Joe↗
NASA NTRS2017

Conceptual Feasibility Study of the Hyperloop Vehicle for Next-Generation Transport

The Hyperloop concept is proposed as a faster, cheaper alternative to high-speed rail and traditional short-haul aircraft. It consists of a passenger pod traveling through a tube under light vacuum while being propelled and levitated by a combination of permanent and electro-magnets. The concept addresses NASA's research thrusts for growth in demand, sustainability, and technology convergence for high-speed transport. Hyperloop is a radical departure from other advanced aviation concepts, however it remains an aeronautics concept that tackles the same strategic goals of low-carbon propulsion and ultra-effcient vehicles. System feasibility was investigated by building a multidisciplinary vehicle sizing model that takes into account aerodynamic, thermodynamic, structures, electromagnetic, weight, and mission analyses. The sizing process emphasized the strong coupling between the two largest systems: the tube and the passenger pod. The model was then exercised to examine Hyperloop from a technical and cost perspective. The structural sizing analysis of the travel tube demonstrates potential for signi cant capital cost reductions by considering an underwater route. Examination of varying passenger capacity indicates that the system can be operated with a wide range of passenger loads without significant change in operating expenses. Lastly, a high-level sizing study simulated variations in tube area, pressure, pod speed, and passenger capacity showing that there is a tube pressure that minimizes operating energy usage. The value of this optimal tube pressure is highly sensitive to numerous design details. These combined estimates of energy consumption, passenger throughput, and mission analyses all support Hyperloop as a faster and cheaper alternative to short-haul flights. The tools and expertise used to quantify these results also demonstrate how traditional aerospace design methods can be leveraged to handle the complex and coupled design process. Much of the technology development required for the Hyperloop is shared with next-generation aircraft. Furthermore, the substantial public interest and active commercial development make it an ideal candidate as an aircraft technology driver and test bed.

Hyperloop Vehicle↗
NASA NTRS2018

Space Technology Mission Directorate: Game Changing Development Program: Rapid Analysis and Manufacturing Propulsion Technology (RAMPT)

Technology Overview: The RAMPT (Rapid Analysis and Manufacturing Propulsion Technology) project will develop and advance large scale light-weight multi-metallic freeform manufacturing and composite overwrap techniques and analysis capabilities required to implement them to reduce design and fabrication cycles for regeneratively-cooled liquid rocket engine components; RAMPT will reduce design, fabrication, assembly schedules while allowing for reduced parts, increased reliability, significant weight reduction and a healthy American supply chain. Four technology areas developed: 1) Freeform Blown Powder Nozzle; 2) Composite overwrap structural jacket; 3) Bimetallic radial deposition for manifolds; 4) Modeling and analysis tools for Additive and Regen design. Exploration & Science Impact: Addresses longest lead, highest cost and heaviest component in engine; Applicable to Lunar Lander Engine, Booster Engines, Upper Stage Engines, and NTP (Nuclear Thermal Propulsion) Technology; Public-private partnerships with specialty industry vendors, government partners, Commercial Crew, and infusion into commercial space companies and manufacturers; SSTIP (NASA's Strategic Space Technology Investment Plan) Core Investment Area - Launch Propulsion Systems (TA01 (NASA Technology Area 01); Lightweight Space Structures and Materials (TA12); Manufacturing (TA12).

RAMPT↗
DOE OSTI2019

The oxygen reduction reaction catalyzed by Synechocystis sp. PCC 6803 flavodiiron proteins

Photosynthetic flavodiiron (Flv) proteins bind flavin and non-heme Fe cofactors and catalyze the oxygen reduction reaction (ORR) coupled to oxidation of reduced pyridine nucleotides during photosynthetic growth. The activity of Flvs have also been observed to form an important catalytic redox loop with water oxidation necessary for preserving photosynthetic electron transport function in cyanobacteria. To determine how these functions may be related, we investigated the kinetic properties of Flv1 and Flv3 from Synechocystis sp. PCC 6803. Under an oxygen atmosphere, Flv1 and Flv3 were found to catalyze ORR with either NADH or NADPH as the electron donor. Reaction velocity curves were sigmoidal and Flv binding of NAD(P)H was cooperative. Based on mass spectrometry generated structural models, each Flv assembles as a homodimer with two oxidoreductase domains capable of binding two molecules of NAD(P)H per subunit, and the flavins are arranged to support electron transfer to the diiron sites for oxygen reduction. Titrations with NAD(P)H resulted in reduction of the diiron site without the accumulation of stable, reduced flavin intermediates. Altogether, the results provide new insights on the properties of Flv1 and Flv3 that enable tight control of reactivity for the complete reduction of oxygen to water, and in this capacity help preserve photosynthetic electron transport function.

09 BIOMASS FUELS↗
NASA NTRS1985

A method for high order linear system reduction and nonlinear system simplification

Least-squares-type algorithms for reducing the order of linear systems in the frequency domain and simplifying nonlinear systems in time domain are developed and demonstrated. The possible model structures are represented as nodes in a tree, and costs along the branches are assigned using the repeated-Gram-Schmidt orthogonalization procedure of Desrochers and Saridis (1980), permitting identification of the optimal n-term model by searching the tree to depth n, with no need for parameter identification. The efficiency and flexibility of the algorithms is shown in applications to the eighth-order linear system studied by Hsia (1972), a three-state eight-nonlinear-term aircraft-dynamics problem, and the related linear-controller problem (Garrard and Jordan, 1977).

Desrochers, A. A.↗
NASA NTRS2016

Development of a Prototype Model-Form Uncertainty Knowledge Base

Uncertainties are generally classified as either aleatory or epistemic. Aleatory uncertainties are those attributed to random variation, either naturally or through manufacturing processes. Epistemic uncertainties are generally attributed to a lack of knowledge. One type of epistemic uncertainty is called model-form uncertainty. The term model-form means that among the choices to be made during a design process within an analysis, there are different forms of the analysis process, which each give different results for the same configuration at the same flight conditions. Examples of model-form uncertainties include the grid density, grid type, and solver type used within a computational fluid dynamics code, or the choice of the number and type of model elements within a structures analysis. The objectives of this work are to identify and quantify a representative set of model-form uncertainties and to make this information available to designers through an interactive knowledge base (KB). The KB can then be used during probabilistic design sessions, so as to enable the possible reduction of uncertainties in the design process through resource investment. An extensive literature search has been conducted to identify and quantify typical model-form uncertainties present within aerospace design. An initial attempt has been made to assemble the results of this literature search into a searchable KB, usable in real time during probabilistic design sessions. A concept of operations and the basic structure of a model-form uncertainty KB are described. Key operations within the KB are illustrated. Current limitations in the KB, and possible workarounds are explained.

Green, Lawrence L.↗
NASA NTRS2004

NASA Tech Briefs, July 2004

Topics: Optoelectronic Sensor System for Guidance in Docking; Hybrid Piezoelectric/Fiber-Optic Sensor Sheets; Multisensor Arrays for Greater Reliability and Accuracy; Integrated-Optic Oxygen Sensors; Ka-Band Autonomous Formation Flying Sensor; CMOS VLSI Active-Pixel Sensor for Tracking; Lightweight, Self-Deploying Foam Antenna Structures; Electrically Small Microstrip Quarter-Wave Monopole Antennas; A 2-to-28-MHz Phase-Locked Loop; Portable Electromyograph; Open-Source Software for Modeling of Nanoelectronic Devices; Software for Generating Strip Maps from SAR Data; Calibration Software for use with Jurassicprok; Software for Probabilistic Risk Reduction; Software Processes SAR Motion-Measurement Data; Improved Method of Purifying Carbon Nanotubes; Patterned Growth of Carbon Nanotubes or Nanofibers; Lightweight, Rack-Mountable Composite Cold Plate/Shelves; SiC-Based Miniature High-Temperature Cantilever Anemometer; Inlet Housing for a Partial-Admission Turbine; Lightweight Thermoformed Structural Components and Optics; Growing High-Quality InAs Quantum Dots for Infrared Lasers; Selected Papers on Protoplanetary Disks; Module for Oxygenating Water without Generating Bubbles; Coastal Research Imaging Spectrometer; Rapid Switching and Modulation by use of Coupled VCSELs; Laser-Induced-Fluorescence Photogrammetry and Videogrammetry; Laboratory Apparatus Generates Dual-Species Cold Atomic Beam; Laser Ablation of Materials for Propulsion of Spacecraft; Small Active Radiation Monitor; Hybrid Image-Plane/Stereo Manipulation; Partitioning a Gridded Rectangle into Smaller Rectangles; Digital Radar-Signal Processors Implemented in FPGAs; Part 1 of a Computational Study of a Drop-Laden Mixing Layer; and Some Improvements in Signal-Conditioning Circuits.

Source record↗
DOE OSTI2020

Understanding the Impact of Lignocellulosic Biomass Variability on the Size Reduction Process: A Review

The importance of size reduction to the commercial deployment of biomass utilization technologies cannot be overemphasized. Size reduction is necessary to create good flowing, easily digestible lignocellulosic biomass. However, inefficiencies and inconsistencies have not been well addressed for the process of size reduction. This has motivated quite a few research studies, some of which have reported the influence of process variables and pretreatment on the size reduction performance as well as the development of novel size reduction equipment and empirical mathematical models. In this Perspective, we present a systematic and critical evaluation of the state of lignocellulosic biomass size reduction research to provide insights for engineers and scientists for future development and investigation. We first briefly discuss the structural biology and failure mode of lignocellulosic biomass. Then, we present a comprehensive, data-driven picture of the interactions among lignocellulosic biomass attributes, size reduction process variables, pretreatment processes, and size reduction process performance (as defined by product characteristics and size reduction energy consumption). The sizing equipment tool wear issues are also summarized. Finally, we highlight some existing gaps and future research opportunities for lignocellulosic biomass size reduction to inform the development of newer technologies that could effectively produce high-value lignocellulosic biomass particles.

09 BIOMASS FUELS↗
NASA NTRS1980

Large space system control technology status and accomplishments

In the area of antenna modeling and control, preliminary structural models were defined for two representative parabolic reflectors. A control system design evolved for attitude control of the reflectors. The controller design was based on a lumped control concept where the control hardware (sensor and actuators) was mounted at the base of the antenna. In the area of distributed control, static shape control techniques were worked out to establish a prescribed vehicle shape. The corresponding estimation process for determination of vehicle shape from selected sensor measurements was also developed. A model order reduction study was conducted to find the best preflight dynamical models for on board controller design. The problems caused by truncation of the vehicle dynamics required to minimize on board computations were investigated. Estimator designs were developed for on board detection of large structure model errors.

Rodriguez, G.↗