Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Ambient pressure X-ray photoelectron spectroscopy study of room-temperature oxygen adsorption on Cu(1 0 0) and Cu(1 1 1)

We investigated the room-temperature chemisorption of oxygen on Cu(1 0 0) and Cu(1 1 1) using ambient-pressure X-ray photoelectron spectroscopy (APXPS). A shoulder-to-shoulder comparison between the oxygen-gas titration on the two surfaces reveals that Cu(1 0 0) is the more active for oxygen dissociative chemisorption when the surfaces are clean. The (2 $\sqrt{2}$ × $\sqrt{2}$)R45o missing-row reconstruction appears in Cu(1 0 0)’s LEED image after about 10 4 Langmuir of oxygen exposure, whereas on Cu(1 1 1), no long-range ordering was observed throughout the whole experiment. An oxide layer consisting of cuprous and cupric oxide shows up on Cu(1 1 1) at an oxygen exposure that is significantly lower than for Cu(1 0 0). This observation suggests that the presence of (2 $\sqrt{2}$ × $\sqrt{2}$)R45o missing-row reconstruction layer slows down Cu(1 0 0) oxidation. Literature has widely reported that surface morphology influences the copper oxidation process. This study provides an XPS demonstration that copper surface oxide formation in O 2 at room temperature depends on the surface crystallographic orientation.

36 MATERIALS SCIENCE↗

Growth and characterization of thin oriented Co{sub 3}O{sub 4} (111) films obtained by decomposition of layered cobaltates Na{sub x}CoO{sub 2}

The formation and structural characterization of highly (111)-oriented Co{sub 3}O{sub 4} films prepared by a novel procedure from weakly (001)-oriented Na{sub x}CoO{sub 2} is reported. The Na{sub x}CoO{sub 2} films were deposited on both single crystal and amorphous substrates by chemical solution deposition (CSD) method and crystallized at 700 °C. Subsequently they were transformed into (111)-oriented Co{sub 3}O{sub 4} phase during post-growth annealing at 900 °C. The degree of preferred orientation in Co{sub 3}O{sub 4}, which was determined by phi-scan and pole figure measurements, depends on the content of Na in the starting Na{sub x}CoO{sub 2} phase. Surface morphology of the films was investigated using electron microscopy and atomic force microscopy. - Graphical abstract: Structure of growth twins and possible O{sup 2−} stacking sequences in (111)-oriented Co{sub 3}O{sub 4} thin films on α-Al{sub 2}O{sub 3}(001) prepared by chemical solution deposition through the transformation of (001)-oriented Na{sub x}CoO{sub 2} thin film. - Highlights: • Single phase Co{sub 3}O{sub 4} thin films was prepared by means of chemical solution deposition. • Conditions for γ-Na{sub x}CoO{sub 2} to Co{sub 3}O{sub 4} transformation were optimized. • Growth twinning of Co{sub 3}O{sub 4} films due to two possible O{sup 2−} stacking sequences. • Growth with (pseudo)epitaxial relation Co{sub 3}O{sub 4} (111)[−121]//α-Al{sub 2}O{sub 3} (001)[10−10].

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Protein Adhesion on Semi-Fluorinated Polystyrene Surfaces in Static and Dynamic Measurements

Reducing protein adhesion is a critical strategy in fouling-resistant material innovation, with broad applications spanning biomedical and healthcare devices, biosensors, industrial and environmental systems, and other important technological domains. Here, in this study, we elucidated protein adhesion behavior on polystyrene-based thin films by neutron reflectometry (NR) and quartz crystal microbalance with dissipation (QCM-D), using both lysozyme and bovine serum albumin (BSA) as model proteins. To this end, semifluorinated polystyrene thin films with gradient wettability and surface energy were fabricated through dry processing using plasma oxidation and gas-phase deposition. Although it is believed that a fully fluorinated alkyl chain offers extremely low surface energy, thus rejecting foulants, and has been used in many fouling-resistant surface designs, enhanced protein–surface interactions were observed consistently in NR and QCM-D results, due to the combined effects of surface morphology and chemistry. On the contrary, depositing shorter fluorinated silane onto a hydrophilic PS surface contributed to a more homogeneous nanoscale fluorine coating, resulting in less initial protein adsorption and improved surface recovery. Comparative analysis of proteins with different sizes on the nanopatterned semifluorinated surface revealed the influence of molecular characteristics on surface interactions. Lysozyme, being smaller and more compact, showed faster adsorption kinetics and higher surface coverage but largely reversible binding, whereas BSA, with its larger and more flexible structure, formed broader and more stable interfacial layers. This study fills the gap in understanding protein adhesion within the range of hydrophobicity (water contact angle ∼90°), as current strategies often associate with extreme hydrophilic and superhydrophobic surfaces due to hydration or low-surface-energy rejection mechanisms, respectively. It also provides in-depth insights into current combinatorial fouling-resistant surface design.

Yuan, Yue [Oak Ridge National Laboratory (ORNL), O↗

Scalable Surface Micro-Texturing of LLZO Solid Electrolytes for Battery Applications

A challenge for lithium lanthanum zirconate (LLZO)-based solid-state batteries is to increase the critical current density (CCD) to enable high current cycling. A promising strategy is to modify the LLZO surface morphology to provide a larger contact area with the Li metal. Here, a surface-textured thin LLZO electrolyte was prepared through an easily scalable process. The texturing process is a simple pressing of green LLZO tapes between micro-textured substrates. A variety of textures can be produced, depending on the type of substrate, and texturing can be on either one side or both sides. For this work, after pressing and sintering, several micro-patterns are formed on thin LLZO (~118 μm thick). The properties of the various samples were characterized to investigate the impact of surface texturing, and the most promising ones were selected for electrochemical testing in symmetrical lithium cells and full cells. Li symmetric cells using a coarse ridge-textured LLZO exhibit ~2.5 times increased CCD compared to planar non-textured LLZO, and a solid-state full cell shows stable cycling and improved rate performance. Finally, we believe this process offers a favorable trade-off of processing complexity vs structural optimization to maximize CCD.

25 ENERGY STORAGE↗

Effects and thermal stability of hydrogen microwave plasma treatment on tetrahedral amorphous carbon films by in situ ultraviolet photoelectron spectroscopy

This paper reports a comprehensive experimental study on the effects of hydrogen microwave plasma treatment on nonhydrogenated high sp{sup 3} content tetrahedral amorphous carbon (ta-C) film. In this study, a surface C-H dipole layer was first observed by high resolution electron energy loss spectroscopy, showing the presence of C-H bonding states. This resulted in the enhancement of electron field emission of the plasma treated films by largely lowering the turn-on field. Thermal stability tests using in situ ultraviolet photoelectron spectroscopy confirm that the C-H dipole layer not only reduces the work function of the films, it is extremely stable in both ambient and vacuum conditions and can sustain up to 600 deg. C annealing in vacuum. Atomic force microscopy studies also show minimal modifications to the surface morphology, leading to the conclusion that the C-H dipole layer is responsible for lowering the work function. This has improved the electron emission properties which can lead to potential applications such as electron emission displays.

36 MATERIALS SCIENCE↗

Enhanced field emission from cerium hexaboride coated multiwalled carbon nanotube composite films: A potential material for next generation electron sources

Intensified field emission (FE) current from temporally stable cerium hexaboride (CeB{sub 6}) coated carbon nanotubes (CNTs) on Si substrate is reported aiming to propose the new composite material as a potential candidate for future generation electron sources. The film was synthesized by a combination of chemical and physical deposition processes. A remarkable increase in maximum current density, field enhancement factor, and a reduction in turn-on field and threshold field with comparable temporal current stability are observed in CeB{sub 6}-coated CNT film when compared to pristine CeB{sub 6} film. The elemental composition and surface morphology of the films, as examined by scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray measurements, show decoration of CeB{sub 6} nanoparticles on top and walls of CNTs. Chemical functionalization of CNTs by the incorporation of CeB{sub 6} nanoparticles is evident by a remarkable increase in intensity of the 2D band in Raman spectrum of coated films as compared to pristine CeB{sub 6} films. The enhanced FE properties of the CeB{sub 6} coated CNT films are correlated to the microstructure of the films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Direct atomic-scale observation of layer-by-layer oxide growth during magnesium oxidation

The atomic-scale oxide growth dynamics are directly revealed by in situ high resolution transmission electron microscopy during the oxidation of Mg surface. The oxidation process is characterized by the layer-by-layer growth of magnesium oxide (MgO) nanocrystal via the adatom process. Consistently, the nucleated MgO crystals exhibit faceted surface morphology as enclosed by (200) lattice planes. It is believed that the relatively lower surface energies of (200) lattice planes should play important roles, governing the growth mechanism. These results facilitate the understanding of the nanoscale oxide growth mechanism that will have an important impact on the development of magnesium or magnesium alloys with improved resistance to oxidation.

36 MATERIALS SCIENCE↗

Temperature dependence of gas sensing behaviour of TiO{sub 2} doped PANI composite thin films

In the present work we have reported the effect of temperature on the gas sensing properties of TiO{sub 2} doped PANI composite thin film based chemiresistor type gas sensors for hydrogen gas sensing application. PANI and TiO{sub 2} doped PANI composite were synthesized by in situ chemical oxidative polymerization of aniline at low temperature. The electrical properties of these composite thin films were characterized by I-V measurements as function of temperature. The I-V measurement revealed that conductivity of composite thin films increased as the temperature increased. The changes in resistance of the composite thin film sensor were utilized for detection of hydrogen gas. It was observed that at room temperature TiO{sub 2} doped PANI composite sensor shows higher response value and showed unstable behavior as the temperature increased. The surface morphology of these composite thin films has also been characterized by scanning electron microscopy (SEM) measurement.

36 MATERIALS SCIENCE↗

Tomography and optical properties of silver nano-inukshuk

Following a simple dip-and-rinse galvanic displacement reaction silver nano-inukshuks were prepared directly on germanium surfaces. Morphology, 3-dimensional (3D) structure, chemical composition and optical properties of the silver nanostructurs were investigated using scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDX), and cathodoluminescence (CL) spectroscopy. Exact 3D morphology was reconstructed in the by tomography mode of TEM.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Combustion synthesis and structural analysis of nanocrystalline nickel ferrite at low temperature regime

Combustion synthesis of single phase Nickel ferrite was successfully achieved at low temperature regime. The obtained powders were calcinated to increase the crystallinity and their characterization change due to calcinations is investigated in detail. Citric acid used as a chelating agent for the synthesis of nickel ferrite. Pure single phase nickel ferrites were found at this low temperature. The average crystalline sizes were measured by using powder XRD measurements. Surface morphology was investigated through Transmission Electron Microscope (TEM). Particle size calculated in XRD is compared with TEM results. Magnetic behaviour of the samples is analyzed by using Vibrating Sample Magnetometer (VSM). Saturation magnetization, coercivity and retentivity are measured and their results are discussed in detail.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microwave synthesis and electrochemical characterization of Mn/Ni mixed oxide for supercapacitor application

Nanostructured Mn/Ni mixed metal oxide was synthesized at ambient temperature by facile microwave irradiation technique. The crystal structure and surface morphology were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. X-ray diffraction analysis confirmed the formation of Mn/Ni mixed oxide in rhombohedral phase and the grain size calculated was found to be 87 nm. The irregular spherical morphology of the prepared sample was exhibited by the SEM images. The characteristic peaks of FTIR at about 630 cm{sup −1} and 749 cm{sup −1} were attributed to the Mn-O and Ni-O stretching vibrations respectively. The presence of both Mn and Ni in the prepared sample was validated by the EDS spectra which in turn confirmed the formation of mixed oxide. Cyclic voltammetry and galvanostatic chargedischarge measurements were employed to investigate the electrochemical performance of the mixed oxide. The cyclic voltammetry curves demonstrated good capacitive performance of the sample in the potential window −0.2V to 0.9V. The charge discharge study revealed the suitability of the prepared mixed oxide for the fabrication of supercapacitor electrode.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Real-time imaging, spectroscopy, and structural investigation of cathodic plasma electrolytic oxidation of molybdenum

In this paper, the results of the investigation of cathodic plasma electrolytic oxidation (CPEO) of molybdenum at 160 V in a mixed solution of borax, water, and ethylene glycol are presented. Real-time imaging and optical emission spectroscopy were used for the characterization of the CPEO. During the process, vapor envelope is formed around the cathode and strong electric field within the envelope caused the generation of plasma discharges. The spectral line shape analysis of hydrogen Balmer line H{sub β} (486.13 nm) shows that plasma discharges are characterized by the electron number density of about 1.4 × 10{sup 21 }m{sup −3}. The electron temperature of 15 000 K was estimated by measuring molybdenum atomic lines intensity. Surface morphology, chemical, and phase composition of coatings formed by CPEO were characterized by scanning electron microscopy with energy dispersive x-ray spectroscopy and x-ray diffraction. The elemental components of CPEO coatings are Mo and O and the predominant crystalline form is MoO{sub 3}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Enhanced memory characteristics in organic ferroelectric field-effect transistors through thermal annealing

We report on the memory characteristics of organic ferroelectric field-effect transistors (FeFETs) using spin-coated poly(vinylidene difluoride/trifluoroethylene) (P(VDF/TrFE)) as a gate insulating layer. By thermal annealing the P(VDF/TrFE) layer at temperatures above its melting point, we could significantly improve the on/off current ratio to over 10{sup 4}. Considerable changes in the surface morphology and x-ray diffraction patterns were also observed in the P(VDF/TrFE) layer as a result of the annealing process. The enhanced memory effect is attributed to large polarization effects caused by rearranged ferroelectric polymer chains and improved crystallinity in the organic semiconductor layer of the FeFET devices.

36 MATERIALS SCIENCE↗

Deuterium plasma induced preferential erosion in ultra-high temperature ceramics TiB 2 and ZrB 2 *

Abstract Steady-state deuterium plasma exposures were performed on ultra-high temperature ceramics titanium diboride (TiB 2 ) and zirconium diboride (ZrB 2 ) using the PISCES-RF linear plasma device (LPD) as early screening for first wall, plasma-facing applications. Deuterium plasma exposures were performed using 40 eV ion energies at 240, 525, and 800 °C sample temperatures and 90 eV ion energies at 240 °C sample temperatures to analyze TiB 2 and ZrB 2 surface morphology and chemistry evolution behavior. Post-plasma exposure chemistry characterization of the near surface ( < 50 nm) region of the samples all show transition metal enrichment, indicating boron preferential erosion. Transition metal to boron fractions vary with plasma exposure temperature under the 40 eV ion energy; metal enrichment is maximized at 800 °C and then minimized at 525 °C. SEM micrographs of all plasma exposed sample surfaces show no significant or noticeable plasma induced damage from cracking or blistering.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mechanisms of Pattern Formation and Smoothing Induced by Ion-Beam Erosion

We have investigated bombardment-induced pattern formation and smoothening during Ar+ ion erosion of Al2O3 surfaces. The experiments show that ion smoothening of a patterned surface is explained by a mechanism where collisions with near-surface atoms produce an effective downhill current. Quantitative agreement is obtained using ion-collision simulations to compute the magnitude of the surface current. The results lead to predictions for the surface morphology phase diagram as a function of ion energy and incidence angle that substantially agree with experimental results.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of pulsed sputtering frequency on the uniformity of Al:ZnO's transparent conductive oxide properties for solar cell applications

Bipolar pulsed magnetron sputtering is used to deposit Al doped ZnO (AZO) on a glass substrate for a transparent conducting oxide in a solar cell structure. A 5x25 in.{sup 2} AZO target was sputtered by 50-250 kHz bipolar pulsed dc power supply to deposit a 400x400 mm{sup 2} area by swinging back and forth. Sheet resistance, surface morphology, and optical transmittance were measured at different positions on 16 witness samples (small glass slides) to evaluate uniformity. In the thickness of 800 nm, the average value of sheet resistance was 30 {Omega}/{open_square} and the average resistivity was 2.1x10{sup -3} {Omega} cm. Transmittance was 50%-80% over the visible range. The nonuniformities of thickness, transmittance, and resistivity in the 400x400 mm{sup 2} area were 5.8%, 0.8%, and within 9.5%, respectively.

14 SOLAR ENERGY↗

Growth of K(Cl, Br) crystals from aqueous solutions in an X-ray field

The influence of X-rays of different wavelength on the degree of structural quality of K(Cl, Br) crystals of mixed composition grown from aqueous solutions is considered. It is found by the methods of chemical etching, X-ray analysis, pycnometric density, and atomic-force microscopy that X-ray irradiation leads to the formation of crystals with a more perfect substructure and surface morphology and a decrease of the dislocation density and concentration of pores and cavities containing the mother liquor. It is shown that X-ray irradiation can promote preferential incorporation of less electronegative components into the crystal lattice of a solid solution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ab initio calculation and spectral properties of nano- and bulk materials

This paper presents the development of ab initio calculation of the electronic structure of either clusters, nano-crystals, doped and unperfected bulk crystals. In addition, analysis of selected experimental data for {gamma}- or plasma irradiated pure and doped wide-band gap oxides such as sapphire, {alpha}-Al{sub 2}O{sub 3}, garnet, Y{sub 3}Al{sub 5}O{sub 12}, Gd{sub 3}Sc{sub 2}Al{sub 3}O{sub 12} and perovskites YAlO{sub 3}, SrTiO{sub 3} is presented. Change in the crystals surface morphology and spectroscopic properties of sapphire, perovskites, garnets as well as ion oxidation state in pure and doped {gamma}- and plasma irradiated crystals are discussed in detail using the optical and X ray spectroscopy experimental results.

36 MATERIALS SCIENCE↗