Results for “target configuration” — Page 30

NASA NTRSDate not supplied

Handling Qualities Assessment of Manual Lunar Landing with Display Augmentation

Research and development is being conducted to support data-driven design decisions for manual control and human involvement in the lunar landing task under the Human Landing System (HLS) program within the Artemis campaign. A human-in-the-loop simulator evaluation of the manual control of a lunar landing vehicle in the final approach and landing phase was conducted at NASA Langley Research Center in the Lunar Flight Deck simulator using the Altair Design and Analysis Cycle (DAC)-2 government reference vehicle. The objective was to perform a direct comparison of control law types with display aiding for various rotational control powers being considered under HLS. Ten subjects (four NASA test pilots and six current pilot astronauts) provided Cooper-Harper ratings, NASA Task Load Index workload ratings, and qualitative comments. The piloting task was to assume manual control of the vehicle (including vertical descent rate) at 150 m above the landing zone, fly to a redesignated landing target (which was up to 75 m radially from the center of the landing zone) and to touch down within a position accuracy of 5m. The data showed that the display augmentation in the form of a “hover cue” significantly improved the pilot’s ability to control translation and create satisfactory handling qualities for otherwise sluggish configurations; however, the investigation also showed that display augmentation is not a panacea. Handling qualities problems, including pilot-induced oscillations, and higher workload for the lowest control powers can still be evident.

Lynda J. Kramer↗

NASA NTRSDate not supplied

Handling Qualities Assessment of Manual Lunar Landing with Display Augmentation

Research and development is being conducted to support data-driven design decisions for manual control and human involvement in the lunar landing task under the Human Landing System (HLS) program within the Artemis campaign. A human-in-the-loop simulator evaluation of the manual control of a lunar landing vehicle in the final approach and landing phase was conducted at NASA Langley Research Center in the Lunar Flight Deck simulator using the Altair Design and Analysis Cycle (DAC)-2 government reference vehicle. The objective was to perform a direct comparison of control law types with display aiding for various rotational control powers being considered under HLS. Ten subjects (four NASA test pilots and six current pilot astronauts) provided Cooper-Harper ratings, NASA Task Load Index workload ratings, and qualitative comments. The piloting task was to assume manual control of the vehicle (including vertical descent rate) at 150 m above the landing zone, fly to a redesignated landing target (which was up to 75 m radially from the center of the landing zone) and to touch down within a position accuracy of 5m. The data showed that the display augmentation in the form of a “hover cue” significantly improved the pilot’s ability to control translation and create satisfactory handling qualities for otherwise sluggish configurations; however, the investigation also showed that display augmentation is not a panacea. Handling qualities problems, including pilot-induced oscillations, and higher workload for the lowest control powers can still be evident.

Lynda Kramer↗

NASA NTRS1979

Calculation of resonant effects in electron-impact excitation of positive ions Application to oxygen VII

The general reaction theory of Feshbach is applied to the calculation of resonant effects in near-threshold electron-positive-ion excitation. The theory divides configuration space into open- and closed-channel parts, resonance effects being described by the closed-channel part. The open-channel part is handled in a distorted-wave approximation to the set of open-channel coupled equations. Various methods are suggested for handling the closed-channel part. However, an 'attached-excited-target approximation' is used explicitly, which is further approximated by a set of uncoupled closed-channel equations. As an example, the 1 1S-2 1P excitation cross section of O VII below the 3 3S threshold is calculated. Various distorted-wave approximations are investigated and results from most of them are quite similar. Resonant effects arising from the attachment of the colliding electron with the 3 3S state are found to be small, but other close-lying n = 3 states have not yet been included.

Pindzola, M. S.↗

NASA NTRS1986

Transitions of the type 2s-2p in oxygenlike Y, Zr, and Nb

Transitions of the type 2s-2p in the oxygenlike ions Y XXXII, Zr XXXIII, and Nb XXXIV were identified in spectra recorded at the University of Rochester's Omega laser facility. Solid targets were spherically irradiated by 24 beams of frequency-tripled (351-nm) Nd-glass laser radiation. The spectra were photographed with a 3-m grazing-incidence spectrograph. The identified transitions of the oxygenlike ions are in the range 30 to 73 A. The wavelengths for the magnetic-dipole transitions within the 2s2p4 ground configurations of these ions are predicted from the experimental energy levels.

Behring, W. E.↗

NASA NTRS2000

Characteristics of Monolithically Integrated InGaAs Active Pixel Imager Array

Switching and amplifying characteristics of a newly developed monolithic InGaAs Active Pixel Imager Array are presented. The sensor array is fabricated from InGaAs material epitaxially deposited on an InP substrate. It consists of an InGaAs photodiode connected to InP depletion-mode junction field effect transistors (JFETs) for low leakage, low power, and fast control of circuit signal amplifying, buffering, selection, and reset. This monolithically integrated active pixel sensor configuration eliminates the need for hybridization with silicon multiplexer. In addition, the configuration allows the sensor to be front illuminated, making it sensitive to visible as well as near infrared signal radiation. Adapting the existing 1.55 micrometer fiber optical communication technology, this integration will be an ideal system of optoelectronic integration for dual band (Visible/IR) applications near room temperature, for use in atmospheric gas sensing in space, and for target identification on earth. In this paper, two different types of small 4 x 1 test arrays will be described. The effectiveness of switching and amplifying circuits will be discussed in terms of circuit effectiveness (leakage, operating frequency, and temperature) in preparation for the second phase demonstration of integrated, two-dimensional monolithic InGaAs active pixel sensor arrays for applications in transportable shipboard surveillance, night vision, and emission spectroscopy.

Kim, Q.↗

NASA NTRS2010

Advanced Wavefront Sensing and Control Testbed (AWCT)

The Advanced Wavefront Sensing and Control Testbed (AWCT) is built as a versatile facility for developing and demonstrating, in hardware, the future technologies of wave front sensing and control algorithms for active optical systems. The testbed includes a source projector for a broadband point-source and a suite of extended scene targets, a dispersed fringe sensor, a Shack-Hartmann camera, and an imaging camera capable of phase retrieval wavefront sensing. The testbed also provides two easily accessible conjugated pupil planes which can accommodate the active optical devices such as fast steering mirror, deformable mirror, and segmented mirrors. In this paper, we describe the testbed optical design, testbed configurations and capabilities, as well as the initial results from the testbed hardware integrations and tests.

active optics↗

NASA NTRS2020

Challenges of Mars Sample Return Lander Entry, Descent, and Landing

The proposed Mars Sample Return (MSR) campaign would be perhaps the most ambitious robotic mission ever attempted in space exploration. The notional cam-paign consists of three Flagship-class missions operating in cooperation for over a decade in order to return samples of the Martian surface and atmosphere to Earth for analysis. The Mars 2020 rover, scheduled to launch in July 2020, will cache samples and place them on the surface for possible return. The second mission would be a Sample Return Lander (SRL) that consists of a small Sample Fetch Rover (SFR) to gather the samples, a Sample Transfer Arm (STA) to load the samples into a Mars Ascent Vehicle (MAV), and the MAV itself to launch the samples into orbit around Mars. The third mission would be an Earth Return Or-biter (ERO) designed to rendezvous and capture the Orbiting Sample (OS), return to Earth, and separate the Earth Entry Vehicle (EEV) for Entry, Descent, and Landing (EDL) at a location to be determined. This paper will focus on the SRL mission concept, specifically the EDL phase. Given the ambitious SRL sample re-trieval baseline surface mission, including a rocket launch of the samples into Mars orbit, it is estimated that the EDL system may be required to deliver as much as 2100 kg of dry mass to the surface. This represents an approximate 20-25% in-crease in mass capability over previous landed Mars missions. Additionally, there is a high probability that SRL would have to land very close to the samples on the surface to expedite retrieval operations; therefore, Pin Point Landing (PPL) accu-racy may be required. To address these challenges, promising EDL configuration augmentations were studied to include larger forebody/higher drag entry capsules, hypersonic/supersonic inflatable/non-inflatable aerodynamic decelerators, hypersonic trim tabs, ballute drag devices, larger parachutes, higher Mach and higher dynamic pressure parachute deployments, lower parachute deployment altitudes having shorter chute timelines necessitating more efficient terrain sensor strategies, and ad-ditional fuel for longer powered descent diverts to the target landing site. Over-arching the entire trade study was an attempt to stay as close to the experience base of past successful missions as possible to reduce implementation cost and risk. This paper will discuss the entire SRL EDL trade study in detail. The information presented about the potential MSR campaign is pre-decisional and is provided for planning and discussion purposes only.

Ivanov, Mark C.↗

NASA NTRSDate not supplied

Advanced Supersonic Parachute Inflation Research and Experiment-2 (ASPIRE2) Flight Mechanics Modeling and Simulation

Introduction: The Advanced Supersonic Para-chute Inflation Research Experiment-2 (ASPIRE2) program is a sounding rocket flight test to be conducted at Wallops Island, VA in early 2025. This program is a risk mitigation exercise for the Mars Sample Retrieval Lander (MSRL) program and builds upon the success of the 2017 & 2018 ASPIRE program, [1,2]. While the ASPIRE program certified the strengthened 21.5 m diameter disk-gap-band (DGB) deployed at Mach 1.7, ASPIRE2 will certify a 24 m diameter DGB deployed at Mach 2.1. The need to certify this increased parachute performance is driven the increased lander mass for MSRL; over 50% increase in comparison to M2020. Modeling: Like its predecessor, ASPIRE2 is developing a multi-body flight dynamics simulation to predict parachute dynamics and aide in designing the flight test that will target Mars-relevant flight conditions, as shown in Figure 1. This work de-scribes the parachute modeling, flight mechanics simulations (from payload separation to splash-down), and design trades used to prepare for the 2025 ASPIRE2 flight. Discussed herein are comparisons between ASPIRE and ASPIRE2, noting key differences in the parachute modeling and vehicle configuration. A study on the attitude control system performance impacts with respect to payload section design will also be presented. This work will quantify the pre-flight parachute performance in the presence of uncertainties, such as those associated with the separation from the sounding rocket, atmosphere, the parachute system, and vehicle mass. The pre-flight predictions will include Monte Carlo analyses, powered by the flight mechanics simulations to show the ASPIRE2 vehicle performance in meeting program requirements on parachute deployment conditions (Mach & dynamic pressure), parachute loads, vehicle attitude at key milestones, and the vehicle splashdown conditions.

Entry Descent and Landing↗

NASA NTRSDate not supplied

Lunar Water Extraction Via Lunar Auger Dryer ISRU (LADI)

In 2009, the Lunar Reconnaissance Orbiter (LRO) and Lunar Crater Observation and Sensing Satellite (LCROSS) provided definitive proof of water in the Lunar’s southern permanently shadowed region (PSR)1. Both the 2020 NASA Technology Taxonomy2 and the Lunar Surface Innovation Initiative (LSII) team identified capability gaps in icy regolith transfer and reactor processing in Permanently Shadowed Region (PSR) environmental conditions. A water processing plant operating inside the PSR can continuously process water (and volatiles) for both breathable air and propellant. NASA’s Johnson Space Center (JSC) fabricated a unique breadboard test stand for validating the feasibility of this concept,developed a lunar auger dryer sizing tool, and identified the physical flow and thermal models required to design an Engineering Development Unit (EDU) for environmental testing. Over the two years this project was active, models were developed including: a) a sizing tool that scales the auger parameters based on production targets, b) accurate thermal models in both lab and lunar conditions, c) a Discreet Element Model (DEM) for observing particle effects in low-g, and d) incorporated these subsystem models into a MATLAB parametric Modular Open System Approach (MOSA) system model. These models were validated by testing the auger in both a mechanical and thermal system configuration. The results of this testing increased the Technology Readiness Level (TRL) of the Lunar Auger Dryer ISRU (LADI) system to TRL 4.

Lunar↗

NASA NTRS1982

Piloted simulator evaluation of a relaxed static stability fighter at high angle-of-attack

A piloted simulator evaluation of the stability and control characteristics of a relaxed static stability fighter aircraft was conducted using a differential maneuvering simulator. The primary purpose of the simulation was to evaluate the effectiveness of the limiters in preventing departure from controlled flight. The simulation was conducted in two phases, the first consisting of open-loop point stability evaluations over a range of subsonic flight conditions, the second concentrating on closed-loop tracking of a preprogrammed target in low speed, high angle-of-attack air combat maneuvering. The command limiters were effective in preventing departure from controlled flight while permitting competent levels of sustained maneuvering. Parametric variations during the study included the effects of pitch control power and wing-body static margin. Stability and control issues were clearly shown to impact the configuration design.

Lapins, M.↗

NASA NTRS1986

The collision of high-velocity clouds with a galactic disk

Two-dimensional hydrodynamic simulations for the interaction of high-velocity clouds with a galactic disk are presented. The impinging clouds are assumed to be spherical and the target disk is represented by a constant density slab, n(g) = 1/cu cm, with a total width W(g) = 200 pc. The numerical experiments cover a wide range of cloud densities, between 0.1 and 100/cu cm, and velocities between 100 and 300 km/s. At a time approximately 10 to the 7th yr after impact, two types of final configurations are found. In the first case, the infalling cloud is completely shocked in a time short compared with the crossing time of the disk. Then, the generated cavity has time to grow sideways and large scale structures with a round shape, and in some cases nearly spherical, are produced. In the second case, which occurs for high density clouds, the cloud is shocked on a time scale longer than or comparable to the crossing time. The resultant cylindrical holes drilled across the entire disk have the dimensions of the impinging cloud. Cloud-galaxy interactions are compared with other energy sources and the morphologies of the resultant structures are suggested to resemble the large scale structures observed in H I.

Tenorio-Tagle, G.↗

NASA NTRS2009

Event Driven Messaging with Role-Based Subscriptions

Event Driven Messaging with Role-Based Subscriptions (EDM-RBS) is a framework integrated into the Service Management Database (SMDB) to allow for role-based and subscription-based delivery of synchronous and asynchronous messages over JMS (Java Messaging Service), SMTP (Simple Mail Transfer Protocol), or SMS (Short Messaging Service). This allows for 24/7 operation with users in all parts of the world. The software classifies messages by triggering data type, application source, owner of data triggering event (mission), classification, sub-classification and various other secondary classifying tags. Messages are routed to applications or users based on subscription rules using a combination of the above message attributes. This program provides a framework for identifying connected users and their applications for targeted delivery of messages over JMS to the client applications the user is logged into. EDMRBS provides the ability to send notifications over e-mail or pager rather than having to rely on a live human to do it. It is implemented as an Oracle application that uses Oracle relational database management system intrinsic functions. It is configurable to use Oracle AQ JMS API or an external JMS provider for messaging. It fully integrates into the event-logging framework of SMDB (Subnet Management Database).

Bui, Tung↗

NASA NTRS2011

Advanced Development of a Compact 5-15 lbf Lox/Methane Thruster for an Integrated Reaction Control and Main Engine Propulsion System

This paper describes the advanced development and testing of a compact 5 to 15 lbf LOX/LCH4 thruster for a pressure-fed integrated main engine and RCS propulsion system to be used on a spacecraft "vertical" test bed (VTB). The ability of the RCS thruster and the main engine to operate off the same propellant supply in zero-g reduces mass and improves mission flexibility. This compact RCS engine incorporates several features to dramatically reduce mass and parts count, to ease manufacturing, and to maintain acceptable performance given that specific impulse (Isp) is not the driver. For example, radial injection holes placed on the chamber body for easier drilling, and high temperature Haynes 230 were selected for the chamber over other more expensive options. The valve inlets are rotatable before welding allowing different orientations for vehicle integration. In addition, the engine design effort selected a coil-on-plug ignition system which integrates a relay and coil with the plug electrode, and moves some exciter electronics to avionics driver board. The engine injector design has small dribble volumes to target minimum pulse widths of 20 msec. and an efficient minimum impulse bit of less than 0.05 lbf-sec. The propellants, oxygen and methane, were chosen because together they are a non-toxic, Mars-forward, high density, space storable, and high performance propellant combination that is capable of pressure-fed and pump-fed configurations and integration with life support and power subsystems. This paper will present the results of the advanced development testing to date of the RCS thruster and the integration with a vehicle propulsion system.

Hurlbert, Eric A.↗

NASA NTRSDate not supplied

Conceptual Design of Propulsors for the SUSAN Electrofan Transport Aircraft

Conceptual designs of the propulsor modules for the SUSAN electro-fan aircraft are sought after. Shaft power requirement is reduced by using boundary layer ingesting propulsion technology. There are several obstacles to designing feasible BLI propulsion systems such as inlet distortion, flow blockage from ingesting low-momentum flow, strong coupling between airframe and propulsion systems. Thus, the high fidelity CFD tool is indispensable to assess the performance of the propulsion systems and evaluate the inlet profiles during the design process. Consequently, the CFD data is used to update the inputs for the NPSS model from the initial stage of the system design. Hence, the inlet sizing, fan design, and estimation of the power saving are carried out. Various installation concepts of the mail-slot nacelle, such as under-/over-wing and trailing edge configurations, are investigated for the wing-mounted turbo-electric distributed propulsor module, and their power-saving is evaluated. As for the tail-mounted turbofan engine, the fan diameter and inlet captured area is determined based on the CFD profiles. An appropriate area ratio of the bypass and core ducts is derived from meeting the target bypass ratio from the system design. The baseline fan stage is analyzed by full annulus URANS CFD to assess the efficiency penalty due to the ingested pressure and swirl distortions.

SUSAN Electro-Fan Aircraft↗

NASA NTRSDate not supplied

Conceptual Design of Propulsors for the SUSAN Electrofan Transport Aircrafts

Conceptual designs of the propulsor modules for the SUSAN electro-fan aircraft are sought after. Shaft power requirement is reduced by using boundary layer ingesting propulsion technology. There are several obstacles to designing feasible BLI propulsion systems such as inlet distortion, flow blockage from ingesting low-momentum flow, strong coupling between airframe and propulsion systems. Thus, the high fidelity CFD tool is indispensable to assess the performance of the propulsion systems and evaluate the inlet profiles during the design process. Consequently, the CFD data is used to update the inputs for the NPSS model from the initial stage of the system design. Hence, the inlet sizing, fan design, and estimation of the power saving are carried out. Various installation concepts of the mail-slot nacelle, such as under-/over-wing and trailing edge configurations, are investigated for the wing-mounted turbo-electric distributed propulsor module, and their power-saving is evaluated. As for the tail-mounted turbofan engine, the fan diameter and inlet captured area is determined based on the CFD profiles. An appropriate area ratio of the bypass and core ducts is derived from meeting the target bypass ratio from the system design. The baseline fan stage is analyzed by full annulus URANS CFD to assess the efficiency penalty due to the ingested pressure and swirl distortions.

Electric Aircraft↗

NASA NTRS1987

Oscillator strengths for S I, S II, and S III

A series of calculations for atomic data of various sulfur and oxygen ions is examined. Recent observations of the Io plasma torus obtained with the Voyager UV Spectrometer, the IUE satellite short wavelength spectrograph, and the rocket-borne faint object telescope are discussed. The calculation of oscillator strengths for S II, the P I sequence, S I, and S III in terms of configuration interaction effects is described. The derivation of orbital wave functions is considered. The use of the close coupling method to estimate collision strengths is studied. The accuracy of these calculations depends on: (1) the number of states used in the close coupling expansion; (2) resonance contributions to the thermally averaged collision strength; and (3) the quality of the target state wave functions. Tables of the derived oscillator strengths are presented.

Ho, Y. K.↗

NASA NTRS1991

A relative-intensity two-color phosphor thermography system

The NASA LaRC has developed a relative-intensity two-color phosphor thermography system. This system has become a standard technique for acquiring aerothermodynamic data in LaRC Hypersonic Facilities Complex (HFC). The relative intensity theory and its application to the LaRC phosphor thermography system is discussed along with the investment casting technique which is critical to the utilization of the phosphor method for aerothermodynamic studies. Various approaches to obtaining quantitative heat transfer data using thermographic phosphors are addressed and comparisons between thin-film data and thermographic phosphor data on an orbiter-like configuration are presented. In general, data from these two techniques are in good agreement. A discussion is given on the application of phosphors to integration heat transfer data reduction techniques (the thin film method) and preliminary heat transfer data obtained on a calibration sphere using thin-film equations are presented. Finally, plans for a new phosphor system which uses target recognition software are discussed.

Merski, N. Ronald↗

NASA NTRS2013

Segmented Liner to Control Mode Scattering

The acoustic performance of duct liners can be improved by segmenting the treatment. In a segmented liner treatment, one stage of liner reduces the target sound and scatters energy into other acoustic modes, which are attenuated by a subsequent stage. The Curved Duct Test Rig is an experimental facility in which sound incident on the liner can be generated in a specific mode and the scatter of energy into other modes can be quantified. A series of experiments is performed in which the baseline configuration is asymmetric, that is, a liner is on one side wall of the test duct and the wall opposite is acoustically hard. Segmented liner treatment is achieved by progressively replacing sections of the hard wall opposite with liner in the axial direction, from 25% of the wall surface to 100%. It is found that the energy scatter from the (0,0) to the (0,1) mode reduces as the percentage of opposite wall treatment increases, and the frequency of peak attenuation shifts toward higher frequency. Similar results are found when the incident mode is of order (0,1) and scatter is into the (0,0) mode. The propagation code CDUCT-LaRC is used to predict the effect of liner segmenting on liner performance. The computational results show energy scatter and the effect of liner segmentation that agrees with the experimental results. The experiments and computations both show that segmenting the liner treatment is effective to control the scatter of incident mode energy into other modes. CDUCT-LaRC is shown to be a valuable tool to predict trends of liner performance with liner configuration.

Gerhold, Carl H.↗