Search NASA⌕ Search

SEARCH · Search NASA

Results for “wall modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

New Predictive Capabilities for Nuclear Weapons in Composite Fires

The prevalence of flammable carbon-based composite airframe materials and their use in high-temperature nuclear weapon re-entry systems requires analysts to address the abnormal thermal environment hazards associated with composite material fires. These fires tend to burn very differently than conventional fuel fires, usually burning less intensely, but much longer. This could lead to challenges in understanding margins in classic safety themes. The technical challenges in modeling the phenomena associated with these new types of fires are considerable, but new models have been developed. Their predictions have been compared with well-documented measurements of a vertical porous burner fire, known as a "wall fire" (a "wall-fire" validation simulation is reflected in the figures below). These measurements were conducted at FMGlobal, a mutual insurance company with a strong fire risk management program, as part of an ongoing collaboration between Sandia and FMGlobal. To date, the "wall-fire" scenario has been set up and initial model assessments with grid refinement studies have been conducted focusing on mesh resolutions suitable for full weapon system simulations. This work will continue with further verification and validation tasks assessing the predictions of the new model. Future work will address specific aspects of the wall models that are lacking in their predictive ability.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
NASA NTRS1989

Mathematical modeling and analysis of heat pipe start-up from the frozen state

The start-up process of a frozen heat pipe is described and a complete mathematical model for the start-up of the frozen heat pipe is developed based on the existing experimental data, which is simplified and solved numerically. The two-dimensional transient model for the wall and wick is coupled with the one-dimensional transient model for the vapor flow when vaporization and condensation occur at the interface. A parametric study is performed to examine the effect of the boundary specification at the surface of the outer wall on the successful start-up from the frozen state. For successful start-up, the boundary specification at the outer wall surface must melt the working substance in the condenser before dry-out takes place in the evaporator.

Jang, Jong Hoon↗
NASA NTRS1990

Mathematical modeling and analysis of heat pipe start-up from the frozen state

The start-up process of a frozen heat pipe is described and a complete mathematical model for the start-up of the frozen heat pipe is developed based on the existing experimental data, which is simplified and solved numerically. The two-dimensional transient model for the wall and wick is coupled with the one-dimensional transient model for the vapor flow when vaporization and condensation occur at the interface. A parametric study is performed to examine the effect of the boundary specification at the surface of the outer wall on the successful start-up from the frozen state. For successful start-up, the boundary specification at the outer wall surface must melt the working substance in the condenser before dry-out takes place in the evaporator.

Jang, J. H.↗
NASA NTRS2003

Systems Modeling of a Hypothetical SSME Channel-Wall Nozzle

A future upgrade to the Space Shuttle Main Engine (SSME) may be the replacement of the current regenerative cooled tube-wall nozzle with a nozzle using a regeneratively-cooled channel-wall design. The current tube-wall design represents the only major piece of SSME hardware that has not been dramatically updated throughout thc long history of the engine. There are a number of advantages to a channel-wall design including the promise of faster and lower cost fabrication and greater reliability in the field. The technical obstacles in the path of making this happen are many, particularly in the realms of metallurgy and manufacturing techniques. However, one technical area that can and should be addressed in the near term as part of the development of detailed component requirements is a systems type model of the fluid flow and heat transfer processes to which the new design will be exposed. This paper presents the results of an effort to develop a mathematical model of the internal flow for a generic channel-wall nozzle functioning as a direct replacement for the current tube-wall nozzle with a minimum of systems-level changes. Comparisons will be made to mathematical modeling results for the current tube-wall design and the results of various geometrical trade studies will be presented. It is the intent of this work to examine the feasibility of the concept of a direct replacement component with minimum systems-!eve impacts and to highlight potential areas of concern requiring further work in the future.

Greene, William D.↗
DOE OSTI2021

Edge and scrape-off layer modeling for a Fusion Nuclear Science Facility with tungsten walls; a summary report for 2019-21

This report summarizes model development and simulations for the edge/scrape-off layer (SOL) region of a Fusion Nuclear Science Facility (FNSF) as part of the DOE Fusion Energy Systems Studies project. An overview of the FNSF device is given in Ref. 1. Our earlier related modeling of FNSF in the 2015-16 timeframe is reported in Ref. 2, and similar work on the ARIES ACT-1 tokamak device is described in Ref. 3. During 2017-18, we contributed to the analysis of a liquid lithium wall for FNSF [4].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1993

Radiation and phase change of lithium fluoride in an annulus

A one-dimensional thermal model is developed to evaluate the effect of radiation on the phase change of lithium-fluoride (LiF) in an annular canister under gravitational and microgravitational conditions. Specified heat flux at the outer wall of the canister models focused solar flux; adiabatic and convective conditions are considered for the inner wall. A two-band radiation model is used for the combined-mode heat transfer within the canister, and LiF optical properties relate metal surface properties in vacuum to those in LiF. For axial gravitational conditions, the liquid LiF remains in contact with the two bounding walls, whereas a void gap is used at the outer wall to model possible microgravitational conditions. For the adiabatic cases, exact integrals are obtained for the time required for complete melting of the LiF. Melting was found to occur primarily from the outer wall in the 1-g model, whereas it occurred primarily from the inner wall in the mu-g model. For the convective cases, partially melted steady-state conditions and fully melted conditions are determined to depend on the source flux level, with radiation extending the melting times.

Lund, Kurt O.↗
NASA NTRS1981

Aeroelastic instability stoppers for wind tunnel models

A mechanism for diverting the flow in a wind tunnel from the wing of a tested model is described. The wing is mounted on the wall of a tunnel. A diverter plate is pivotally mounted on the tunnel wall ahead of the model. An actuator fixed to the tunnel is pivotably connected to the diverter plate, by plunger. When the model is about to become unstable during the test the actuator moves the diverter plate from the tunnel wall to divert maintaining stable model conditions. The diverter plate is then retracted to enable normal flow.

Doggett, R. V., Jr.↗
NASA NTRS1982

Adaptive-wall wind-tunnel research at NASA-Ames Research Center

Adaptive wall wind tunnel research is summarized. Small scale two and three dimensional wind tunnel experiments and numerical experiments with a three dimensional adaptive wall simulator are included. A NACA 0012 airfoil was tested in a 25 by 13 cm slotted wall test section. Airflow through the test section walls was controlled by adjusting the pressures in segmented plenums. Interference free conditions were successfully attained in subsonic and transonic flows. For the three dimensional experiment, the 25 by 13 cm wind tunnel was modified to permit cross stream wall adjustments. The test model was a semispan wing mounted to one sidewall. Wall interference was substantially reduced at several angles of attack at Mach 0.60. A wing on wall configuration was also modeled in the numerical experiments. These flow simulations showed that free air conditions can be approximated by adjusting boundary conditions at only the floor and ceiling of the test section. No sidewall control was necessary. Typical results from these experiments are discussed.

Schairer, E. T.↗
NASA NTRS1988

Adaptive wall research with two- and three-dimensional models in low speed and transonic tunnels

This paper summarises recent research at the University of Southampton into adaptive wall technology and outlines the direction of current efforts. The work is aimed at developing techniques for use in test sections where the top and bottom walls may be adjusted in single curvature. Wall streamlining eliminates, as far as experimentally possible, the top and bottom wall interference in low speed and transonic aerofoil testing. A streamlining technique has been developed for low speeds which allows the testing of swept wing panels in low interference environments. At higher speeds, a comparison of several two-dimensional transonic streamlining algorithms has been made and a technique for streamlining with a choked test section has also been developed. Three-dimensional work has mainly concentrated on tests of sidewall mounted half-wings and the development of the software packages required to assess interference and to adjust the flexible walls. It has been demonstrated that two-dimensional wall adaptation can significantly modify the level of wall interference around relatively large three-dimensional models. The residual interferences are small and are probably amenable to standard post-test correction methods. Tests on a calibrated wing-body model are planned in the near future to further validate the proposed streamlining technique.

Lewis, M. C.↗
NASA NTRS1992

Analysis of film cooling in rocket nozzles

Computational Fluid Dynamics (CFD) programs are customarily used to compute details of a flow field, such as velocity fields or species concentrations. Generally they are not used to determine the resulting conditions at a solid boundary such as wall shear stress or heat flux. However, determination of this information should be within the capability of a CFD code, as the code supposedly contains appropriate models for these wall conditions. Before such predictions from CFD analyses can be accepted, the credibility of the CFD codes upon which they are based must be established. This report details the progress made in constructing a CFD model to predict the heat transfer to the wall in a film cooled rocket nozzle. Specifically, the objective of this work is to use the NASA code FDNS to predict the heat transfer which will occur during the upcoming hot-firing of the Pratt & Whitney 40K subscale nozzle (1Q93). Toward this end, an M = 3 wall jet is considered, and the resulting heat transfer to the wall is computed. The values are compared against experimental data available in Reference 1. Also, FDNS's ability to compute heat flux in a reacting flow will be determined by comparing the code's predictions against calorimeter data from the hot firing of a 40K combustor. The process of modeling the flow of combusting gases through the Pratt & Whitney 40K subscale combustor and nozzle is outlined. What follows in this report is a brief description of the FDNS code, with special emphasis on how it handles solid wall boundary conditions. The test cases and some FDNS solution are presented next, along with comparison to experimental data. The process of modeling the flow through a chamber and a nozzle using the FDNS code will also be outlined.

Woodbury, Keith A.↗
DOE OSTI2021

Dependency of active pressure and equation of state on stiffness of wall

Autonomous motion and motility are hallmarks of active matter. Active agents, such as biological cells and synthetic colloidal particles, consume internal energy or extract energy from the environment to generate self-propulsion and locomotion. These systems are persistently out of equilibrium due to continuous energy consumption. It is known that pressure is not always a state function for generic active matter. Torque interaction between active constituents and confinement renders the pressure of the system a boundary-dependent property. The mechanical pressure of anisotropic active particles depends on their microscopic interactions with a solid wall. Using self-propelled dumbbells confined by solid walls as a model system, we perform numerical simulations to explore how variations in the wall stiffness influence the mechanical pressure of dry active matter. In contrast to previous findings, we find that mechanical pressure can be independent of the interaction of anisotropic active particles with walls, even in the presence of intrinsic torque interaction. Particularly, the dependency of pressure on the wall stiffness vanishes when the stiffness is above a critical level. In such a limit, the dynamics of dumbbells near the walls are randomized due to the large torque experienced by the dumbbells, leading to the recovery of pressure as a state variable of density.

42 ENGINEERING↗
DOE OSTI2020

Modeling Catalyzed Growth of Single-Wall Carbon Nanotubes (Final Report)

Single-walled carbon nanotubes (SWCNTs) are among the most promising nanostructures because of their special and unusual physico-chemical properties that make them strong candidates for a variety of applications. Since their discovery, chemical vapor deposition (CVD) methods have become the preferred synthesis method. CVD uses a carbon-containing precursor species, which is decomposed over a catalyst yielding C atoms that eventually evolve in carbon nanostructures. CVD temperatures are in the order of 1000K or lower, and pressures in the range of 1-5 atm, although some processes use higher pressures. Depending on the nature of the catalyst, and on the conditions of pressure, temperature, and presence of other inert compounds, the resultant nanostructures may include nanofibers, nano-onions, multiple-, or single-wall carbon nanotubes, among others. When the CVD synthesis process is appropriately tuned, however, it is possible to obtain only SWCNTs, which are geometrically characterized by their diameter and by their chiral angle. The chiral indexes (n,m) determine the degree of helical twist of the graphite lattice along the nanotube axis, where the term chirality is derived from the left and right-handed helicity of the tubes defined by their chiral indexes (n,m) and (m,n) respectively. The main goal of this research is to build fundamental understanding that will help elucidating the nature and structure of the actual catalyst in a combined catalyst/support system, which we claim is essential especially when the catalyst is of nanodimensions. Given that we are considerably advanced in the understanding of selective single-walled carbon nanotube catalyst synthesis, we take this process as a case study. Thus, we focus on the understanding of the selective growth of SWCNTs on supported nanocatalysts in systems where the catalyst synthesis takes place in the same reactor preceding the nanotube synthesis. Once we understand what type of catalyst structure would be necessary for this specific growth, we will try to elucidate the catalytic synthesis process that leads to such catalytic structure. Thus, our aim of controlling nanostructure synthesis may start to be delineated.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermal Hydraulics Analysis of a Divertor Monoblock Using SALAMANDER

Divertors are critical components in magnetic confinement fusion devices. One of the Divertor's crictial roles is absorbing the highest heat flux from the plasma. The Divertor accomplishes this through the use of divertor monoblocks and cooling channels. This work presents a thermal hydraulic analysis of a divertor monoblock using the Software for Advanced Large-scale Analysis of MAgnetic confinement for Numerical Design, Engineering and Research (SALAMANDER). SALAMANDER is an open source tool developed at Idaho National Laboratory for conducting multiphysics and multscale analysis of Plasma Facing Components (PFCs). For the monoblock, solid heat conduction is modeled in the block with a constant heat flux of 1E7 W/m^2 applied to the top of the block to represent peak heat flux from the plasma. The cooling channel (which is pressurized water at a Reynolds number of ~1,000,000) is modeled using a k-epsilon turbulence model with standard wall functions. The heat transfer between the solid and fluid domain is modeled using the Dittus-Boelter correlation for the convective heat transfer coefficient. This work aims to show the importance of a multiphysics modeling approach when performing simulations on PFCs.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗