Results for “Aerodynamic Performance” — Page 31

NASA NTRS1991

Prediction of the pattern performance for the Aeroassist Flight Experiment (AFE) spacecraft

In order to provide a set of benchmark flight data for a reusable Aeroassisted Orbit Transfer Vehicle (AOTV) application, NASA undertook the development of an Aeroassisted Flight Experiment (AFE) which will be launched from the Space Shuttle. A representative aeroassist trajectory will be flown and sensor measurements of aerodynamic performance, thermal protection response, and plasma ionization reentry effects will be obtained. Discussed here is the spacecraft antenna. Estimates of signal transmissions from the AFE to the Tracking and Data Relay Satellites (TDRS) during the reentry period are given. The computer modeling of the antennas is presented with and without the reentry plasma.

Yang, C.↗

NASA NTRS1991

Effect of a simulated ice accretion on the aerodynamics of a swept wing

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional swept wing is studied experimentally. A semispan wing of effective aspect ratio four was mounted from the sidewall of the UIUC subsonic wind tunnel. The model uses a NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root sections to allow for 0- and 30-degree sweep. A sidewall suction system is used to minmize the tunnel boundary-layer interaction with the model. Surface pressure data from five spanwise stations are compared to earlier data from a similar tunnel. A three-component sidewall balance has been designed, built and used to measure lift, drag and pitching moment on the clean and iced model. The data compare well to the integrated pressure data and to theory on the clean model. In addition, helium-bubble flow visualization has been performed on the iced model and reveals extensive spanwise flow in the separation bubble aft of the upper surface horn. This compares well to the computational results of other researchers. Sidewall suction was found to have no effect on the aerodynamics of the swept wing.

Bragg, M. B.↗

NASA NTRS2011

Combined Structural and Trajectory Control of Variable-Geometry Planetary Entry Systems

Some of the key challenges of planetary entry are to dissipate the large kinetic energy of the entry vehicle and to land with precision. Past missions to Mars were based on unguided entry, where entry vehicles carried payloads of less than 0.6 T and landed within 100 km of the designated target. The Mars Science Laboratory (MSL) is expected to carry a mass of almost 1 T to within 20 km of the target site. Guided lifting entry is needed to meet these higher deceleration and targeting demands. If the aerodynamic characteristics of the decelerator are variable during flight, more trajectory options are possible, and can be tailored to specific mission requirements. In addition to the entry trajectory modulation, having variable aerodynamic properties will also favor maneuvering of the vehicle prior to descent. For proper supersonic parachute deployment, the vehicle needs to turn to a lower angle of attack. One approach to entry trajectory improvement and angle of attack control is to embed a variable geometry decelerator in the design of the vehicle. Variation in geometry enables the vehicle to adjust its aerodynamic performance continuously without additional fuel cost because only electric power is needed for actuating the mechanisms that control the shape change. Novel structural and control concepts have been developed that enable the decelerator to undergo variation in geometry. Changing the aerodynamic characteristics of a flight vehicle by active means can potentially provide a mechanically simple, affordable, and enabling solution for entry, descent, and landing across a wide range of mission types, sample capture and return, and reentry to Earth, Titan, Venus, or Mars. Unguided ballistic entry is not sufficient to meet this more stringent deceleration, heating, and targeting demands. Two structural concepts for implementing the cone angle variation, a segmented shell, and a corrugated shell, have been presented.

Quadrelli, Marco B.↗

NASA NTRS2012

Laminar, Transitional, and Turbulent Heating on Mid Lift-to-Drag Ratio Entry Vehicles

The boundary-layer transition characteristics and convective aeroheating levels on mid lift-to-drag ratio entry vehicle configurations have been studied through wind tunnel testing. Several configurations were investigated, including elliptically-blunted cylinders with both circular and elliptically-flattened cross sections, biconic geometries based on launch vehicle dual-use shrouds, and parametrically-optimized analytic geometries. Vehicles of this class have been proposed for high-mass Mars missions, such as sample return and crewed exploration, for which the conventional sphere-cone entry-vehicle geometries of previous Mars missions are insufficient. Testing was conducted at Mach 6 over a range of Reynolds numbers sufficient to generate laminar, transitional, and turbulent flow. Transition onset locations - both straight-line and cross-flow - and heating rates were obtained through global phosphor thermography. Supporting computations were performed to obtain heating rates for comparison with the data. Laminar data and predictions agreed to well within the experimental uncertainty. Fully-turbulent data and predictions also agreed well. However, in transitional flow regions, greater differences were observed. Additional aerodynamic performance data were also generated through Modified-Newtonian analyses of the geometries.

Hollis, Brian R.↗

NASA NTRS1986

Model-following control for an oblique-wing aircraft

A variable-skew oblique wing offers a substantial aerodynamic performance advantage for aircraft missions that require both high efficiency in subsonic flight and supersonic dash or cruise. The most obvious characteristic of the oblique-wing concept is the asymmetry associated with wing-skew angle which results in significant aerodynamic and inertial cross-coupling between the aircraft longitudinal and lateral-directional axes. A technique for synthesizing a decoupling controller while providing the desired stability augmentation. The proposed synthesis procedure uses the cncept of explicit model following. Linear quadratic optimization techniques are used to design the linear feedback system. The effectiveness of the control laws developed in achieving the desired decoupling is illustrated for a given flight condition by application to linearized equations of motion, and also to the nonlinear equations of six degrees of freedom of motion with nonlinear aerodynamic data.

Alag, G. S.↗

NASA NTRS1986

Model-following control for an oblique-wing aircraft

A variable-skew oblique wing offers a substantial aerodynamic performance advantage for aircraft missions that require both high efficiency in subsonic flight and supersonic dash or cruise. The most obvious characteristic of the oblique-wing concept is the asymmetry associated with wing-skew angle which results in significant aerodynamic and inertial cross-coupling between the aircraft longitudinal and lateral-directional axes. This paper presents a technique for synthesizing a decoupling controller while providing the desired stability augmentation. The proposed synthesis procedure uses the concept of explicit model following. Linear quadratic optimization techniques are used to design the linear feedback system. The effectiveness of the control laws developed in achieving the desired decoupling is illustrated for a given flight condition by application to linearized equations of motion, and also to the nonlinear equations of six degrees of freedom of motion with nonlinear aerodynamic data.

Alag, G. S.↗

NASA NTRS1987

Preliminary flight assessment of the X-29A advanced technology demonstrator

Several new technologies integrated on the X-29A advanced technology demonstrator are being evaluated for the next generation of fighter aircraft. Some of the most noteworthy ones are the forward-swept wing, digital fly-by-wire flight control system, close-coupled wing-canard configuration, aeroelastically tailored composite wing skins, three-surface pitch control configuration, and a highly unstable airframe. The expansion of the aircraft 1-g and maneuver flight envelopes was recently completed over a two-year period in 84 flights. Overall flight results confirmed the viability of the aircraft design, and good agreement with preflight predictions was obtained. The individual technologies' operational workability and performance were confirmed. This paper deals with the flight test results and the preliminary evaluation of the X-29A design and technologies. A summary of the primary technical findings in structural static loads, structural dynamic characteristics, flight control system characteristics, aerodynamic stability and control, and aerodynamic performance is presented.

Hicks, John W.↗

NASA NTRS1987

Model-following output feedback controller for oblique-wing aircraft

A variable-skew oblique-wing offers a substantial aerodynamic performance advantage for aircraft missions that require both high efficiency in subsonic flight and supersonic dash or cruise. The most obvious characteristics of the oblique-wing concept is the asymmetry of the wing-skew angle that causes a significant aerodynamic and inertial cross coupling between the aircraft longitudinal and lateral-directional axes. This paper presents a technique for synthesizing a decoupling controller while providing the desired stability augmentation. The use of output feedback in control law synthesis without the requirement of state estimation is presented. An explicit model-following control system with output feedback is developed. The effectiveness of the control laws developed in achieving the desired decoupling is illustrated for a given flight condition for an oblique-wing aircraft.

Alag, Gurbux Singh↗

NASA NTRS1987

Preliminary flight assessment of the X-29A advanced technology demonstrator

Several new technologies integrated on the X-29A advanced technology demonstrator are being evaluated for the next generation of fighter aircraft. Some of the most noteworthy ones are the forward-swept wing, digital fly-by-wire flight control system, close-coupled wing-canard configuration, aeroelastically tailored composite wing skins, three-surface pitch control configuration, and a highly unstable airframe. The expansion of the aircraft 1-g and maneuver flight envelopes was recently completed over a two-year period in 84 flights. Overall flight results confirmed the viability of the aircraft design, and good agreement with preflight predictions was obtained. The individual technologies' operational workability and performance were confirmed. This paper deals with the flight test results and the preliminary evaluation of the X-29A design and technologies. A summary of the primary technical findings in structural static loads, structural dynamic characteristics, flight control system characteristics, aerodynamic stability and control, and aerodynamic performance is presented.

Hicks, John W.↗

NASA NTRSDate not supplied

Wall-Modeled Large-Eddy Simulations of a Swept Wing with Leading-Edge Ice

The aerodynamic performance of a swept wing derived from the Common Research Model wing with high-fidelity and smooth leading-edge ice shapes is evaluated using wall-modeled large-eddy simulations. Two mesh paradigms are considered within the Launch, Ascent, and Vehicle Aerodynamics framework: structured hybrid curvilinear body-fitted/immersed-boundary and unstructured Voronoi. The curvilinear approach models the effect of the ice on the flow through penalty terms and the Voronoi strategy includes the ice representation directly in the mesh.Aerodynamic loads, surface pressure profiles, and skin-friction streamlines are compared against experimental results collected at the Wichita State University wind tunnel at a Mach number of 0.18 and a Reynolds number per mean aerodynamic chord of 1.6 million. For the curvilinear simulations with high-fidelity ice, results are sensitive to spanwise mesh resolution near the leading edge, where insufficient spanwise resolution leads to a spanwise running vortexaft of the high-fidelity ice, which is partially removed with increasing spanwise resolution. For the Voronoi simulations with high-fidelity ice, refining the mesh led to good convergence towards the experimental results with the best case demonstrating a maximum discrepancy of three lift counts relative to the experiment across a range of angles of attack from about 5 to 24 degrees, validating the shrink-wrapping procedure used for the ice. For the smooth ice, the curvilinear approach consistently under-predicted the upper surface suction leading to an under-prediction in lift, but did not demonstrate the pronounced over-prediction in upper surface suction near the leading edge observed in the Voronoi simulations.

AATT↗

NASA NTRS2022

Low-Speed Performance Enhancement using Localized Active Flow Control: Simulations, Scaling and Design of Localized Active Flow Control on the Common Research Model (4/4)

This report is dedicated to the application of localized AFC on the NASA CRM-HL wind tunnel model, with focus on the aileron application discussed in the CFD study (final report document #2). The experience developed for the Reference Aircraft guided the implementation on the CRM model. CFD evaluations are performed on a representative high-lift configuration, for a set of aileron deflections, and at relevant flow conditions. Alternative flow control actuator layouts are proposed and design consideration for practical integration into the existing CRM-HL model are set forth. The CFD simulations indicate that the aerodynamic performance improvements due to AFC obtained for the CRM-HL are consistent with those achieved for the Reference Aircraft. The observed changes in L/D are smaller than for the Reference Aircraft because the CRM has a higher leading edge sweep angle and a different relative aileron size. Conceptual design studies confirmed that the integration of an AFC equipped aileron into the existing wind tunnel model is feasible.

AFC↗

NASA NTRS2002

Annual Research Briefs, 2002: Center for Turbulence Research

Turbulent combustion remains the largest component of the CTR's core program. This program and several related activities at CTR are supported by NASA's Ultra Efficient Engine Technology Program. It is also intimately connected with the Department of Energy's ASCI program at Stanford which develops the technology for numerical simulation of realistic aircraft engines using state of the art massively parallel computers. In combustion modeling the attention has been directed to the modeling of higher levels of complexity such as spray dynamics, radiation and soot formation. Major aircraft engine manufacturers have shown considerable interest in this program; in particular, a significant active collaboration exists between CTR and the Pratt & Whitney Corporation. CTR's combustion program is essentially based on the large-eddy simulation technique, LES, which is actively being pursued at CTR for this and many other applications. Important accomplishments in LES included simulations with three-dimensional filters which result in grid independent calculations (that is why we call it "true" LES), and the development of the methodology for integration of LES and Reynolds Averaged computations. Optimization techniques are being studied and used for the important problem of wall boundary conditions for LES as well as for optimal shape design for aeroacoustic and aerodynamic performance gains.

ULTRA EFFICIENT ENGINE TECHNOLOGY↗

NASA NTRS1975

Small scale noise and wind tunnel tests of upper surface blowing nozzle flap concepts. Volume 1. Aerodynamic test results

The results and analyses of aerodynamic and acoustic studies conducted on the small scale noise and wind tunnel tests of upper surface blowing nozzle flap concepts are presented. Various types of nozzle flap concepts were tested. These are an upper surface blowing concept with a multiple slot arrangement with seven slots (seven slotted nozzle), an upper surface blowing type with a large nozzle exit at approximately mid-chord location in conjunction with a powered trailing edge flap with multiple slots (split flow or partially slotted nozzle). In addition, aerodynamic tests were continued on a similar multi-slotted nozzle flap, but with 14 slots. All three types of nozzle flap concepts tested appear to be about equal in overall aerodynamic performance but with the split flow nozzle somewhat better than the other two nozzle flaps in the landing approach mode. All nozzle flaps can be deflected to a large angle to increase drag without significant loss in lift. The nozzle flap concepts appear to be viable aerodynamic drag modulation devices for landing.

Renselaer, D. J.↗

NASA NTRS1986

A flight test challenge - Aeroassist for reuseable, space-based transportation

Attention is given to the challenges addressed by NASA in the development of reusable, space-based transportation systems which take advantage of aerobraking to achieve greater performance and overall efficiency. Aerobraking environmental factors associated with achieving higher energy reusable systems are outlined and the need for a coupled utilization of ground test capabilities and computational fluid dynamics (CFD) is demonstrated. It is concluded that the certification of CFD capability to provide the aerodynamic performance and aerothermodynamic environment for an aerobraking orbital transfer vehicle would be of major significance for the design and development of future flight systems.

Ried, Robert C.↗

NASA NTRS2017

Greased Lightning (GL-10) Performance Flight Research: Flight Data Report

Modern aircraft design methods have produced acceptable designs for large conventional aircraft performance. With revolutionary electronic propulsion technologies fueled by the growth in the small UAS (Unmanned Aerial Systems) industry, these same prediction models are being applied to new smaller, and experimental design concepts requiring a VTOL (Vertical Take Off and Landing) capability for ODM (On Demand Mobility). A 50% sub-scale GL-10 flight model was built and tested to demonstrate the transition from hover to forward flight utilizing DEP (Distributed Electric Propulsion)[1][2]. In 2016 plans were put in place to conduct performance flight testing on the 50% sub-scale GL-10 flight model to support a NASA project called DELIVER (Design Environment for Novel Vertical Lift Vehicles). DELIVER was investigating the feasibility of including smaller and more experimental aircraft configurations into a NASA design tool called NDARC (NASA Design and Analysis of Rotorcraft)[3]. This report covers the performance flight data collected during flight testing of the GL-10 50% sub-scale flight model conducted at Beaver Dam Airpark, VA. Overall the flight test data provides great insight into how well our existing conceptual design tools predict the performance of small scale experimental DEP concepts. Low fidelity conceptual design tools estimated the (L/D)( sub max)of the GL-10 50% sub-scale flight model to be 16. Experimentally measured (L/D)( sub max) for the GL-10 50% scale flight model was 7.2. The aerodynamic performance predicted versus measured highlights the complexity of wing and nacelle interactions which is not currently accounted for in existing low fidelity tools.

McSwain, Robert G.↗

NASA NTRS1990

Effect of vane twist on the performance of dome swirlers for gas turbine airblast atomizers

For advanced gas turbine engines, two combustor systems, the lean premixed/prevaporized (LPP) and the rich burn/quick quench/lean burn (RQL) offer great potential for reducing NO(x) emissions. An important consideration for either concept is the development of an advanced fuel injection system that will provide a stable, efficient, and very uniform combustion system over a wide operating range. High-shear airblast fuel injectors for gas turbine combustors have exhibited superior atomization and mixing compared with pressure-atomizing fuel injectors. This improved mixing has lowered NO(x) emissions and the pattern factor, and has enabled combustors to alternate fuels while maintaining a stable, efficient combustion system. The performance of high-shear airblast fuel injectors is highly dependent on the design of the dome swirl vanes. The type of swirl vanes most widely used in gas turbine combustors are usually flat for ease of manufacture, but vanes with curvature will, in general, give superior aerodynamic performance. The design and performance of high-turning, low-loss curved dome swirl vanes with twist along the span are investigated. The twist induces a secondary vortex flow pattern which will improve the atomization of the fuel, thereby producing a more uniform fuel-air distribution. This uniform distribution will increase combustion efficiency while lowering NO(x) emissions. A systematic swirl vane design system is presented based on one-, two-, and three-dimensional flowfield calculations, with variations in vane-turning angle, rate of turning, vane solidity, and vane twist as design parameters.

Micklow, Gerald J.↗

NASA NTRS1990

Effect of vane twist on the performance of dome swirlers for gas turbine airblast atomizers

For advanced gas turbine engines, two combustor systems, the lean premixed/prevaporized (LPP) and the rich burn/quick quench/lean burn (RQL) offer great potential for reducing NO(x) emissions. An important consideration for either concept is the development of an advanced fuel injection system that will provide a stable, efficient, and very uniform combustion system over a wide operating range. High-shear airblast fuel injectors for gas turbine combustors have exhibited superior atomization and mixing compared with pressure-atomizing fuel injectors. This improved mixing has lowered NO(x) emissions and the pattern factor, and has enabled combustors to alternate fuels while maintaining a stable, efficient combustion system. The performance of high-shear airblast fuel injectors is highly dependent on the design of the dome swirl vanes. The type of swirl vanes most widely used in gas turbine combustors are usually flat for ease of manufacture, but vanes with curvature will, in general, give superior aerodynamic performance. The design and performance of high-turning, low-loss curved dome swirl vanes with twist along the span are investigated. The twist induces a secondary vortex flow pattern which will improve the atomization of the fuel, thereby producing a more uniform fuel-air distribution. This uniform distribution will increase combustion efficiency while lowering NO(x) emissions. A systematic swirl vane design system is presented based on one-, two-, and three-dimensional flowfield calculations, with variations in vane-turning angle, rate of turning, vane solidity, and vane twist as design parameters.

Micklow, Gerald J.↗

NASA NTRS2005

Cold Aero Performance of a Two-Dimensional Mixer Ejector Nozzle

Since 1986, NASA and the U.S. aerospace industry have been assessing the economic viability and environmental acceptability of a second-generation supersonic civil transport, or High Speed Civil Transport (HSCT). Environmental acceptability in terms of airport community noise and economic viability are critical elements in this endeavor. Development of a propulsion system that satisfies strict airport noise regulations (FAR36 Stage III levels), at acceptable performance and weight, is critical to the success of any HSCT program. Two-dimensional mixer-ejector (2DME) exhaust systems are one approach in achieving this goal. In support of HSCT development, GEAE (GE Aircraft Engines), under contract to the NASA Glenn Research Center, conducted this test program at the NASA Langley 16 ft transonic wind tunnel to evaluate the cold aerodynamic performance aspects of the 2DME exhaust system concept. The effects of SAR (SAR, suppressor area ratio, = mixed-flow area/primary nozzle throat area), MAR (MAR = overall exhaust system exit/mixing-plane area), flap length, CER (suppressor chute expansion ratio), chute alignment, and free stream Mach number were investigated on a 1/11th cold aerodynamic scale model of a 2DME exhaust system.

Balan, C.↗