SEARCH · Search NASA

Results for “Alloy design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

All sources NASA NTRS DOE OSTI

NASA NTRS2003

Uses of Computed Tomography for Characterizing Materials Grown Terrestrially and in Microgravity

Tomography (CT) has proved to be of inestimable use in providing a rapid evaluation of a variety of samples from Mechanics of Granular Materials (MGM) to electronic materials (Ge-Si alloys) to space grown materials such as meteorites. The system at Kennedy Space Center (KSC), because of its convenient geographical location, is ideal for examining samples before launch and immediately after returning to Earth. It also has the advantage of the choice of fluxes, and in particular the use of a radioactive cobalt source, which is basically monochromatic. This permits a reasonable measurement of density to be made from which chemical composition can be determined. Due to the current dearth of long duration space grown materials, the CT instrument has been used: (1) to characterize materials in preparation for flight, (2) to determine thermal expansion values, and (3) to examine long duration space grown materials, i.e. meteorites. This work will first describe the establishment of the protocol for obtaining the optimum density readings for any material. Included will be the effects of the hardware or instrumental parameters that can be controlled, and the techniques used to process the CT data. Examples will be given of the compositional variation along a single crystal of Ge-Si alloy. Density variation with temperature has been measured in preparation for future materials science experiments; this involved the fabrication at MSFC and installation of a single zone furnace at KSC incorporating a heat pipe to ensure high temperature uniformity. At the time of writing the thermal expansion of lead (Pb) has been measured from room temperature to 900 C. Three methods are available. Digital radiography enables length changes to be determined. Prior to melting the sample is smaller than the container and the diameter change can be measured. Most critical, however, is the density change in solid, through the melting region, and in the liquid state. These data are needed for engineering purposes to aid in the design of containment cartridges, and for enabling fluid flow calculations. A second sample, with the Pb alloyed with Sb is ready for scanning. This corresponds to the planned composition of Dr. Poirier s flight experiment. Other materials pertinent to NASA programs such as Al-Cu (Trivedi), CdTe (Banish), HgCdTe (Lehoczky) will be examined below and above the melting point. Finally, three-dimensional results will be shown of the structure of a two-phase metallic meteorite of metal and sulfide, in which the Fe-Ni phase has coarsened during slow cooling over hundreds of millions of years.

Source record↗

NASA NTRS1989

Active control of buckling of flexible beams

Mathematical models are presented that simulate the dynamic characteristics of shape memory alloy actuators made of nickel-titanium alloy (Nitinol) controlling the buckling of compressive structural members. A closed-loop computer-controlled system has been designed, based on the proposed mathematical models, and has been implemented to control the buckling of simple beams. The performance of the computer-controlled system is evaluated experimentally and compared with the theoretical predictions to validate the developed models. The results emphasized the importance of buckling control and suggest the potential of shape memory alloy actuators as attractive means for controlling structural deformation in a simple and reliable way.

Baz, A.↗

NASA NTRSDate not supplied

Development and Optimization of Additively Manufactured NASA HR-1 for Space Applications

Metal additive manufacturing (AM) processes have been demonstrated to be effective at reducing costs and lead times associated with fabrication of complex propulsion component designs. Laser powder directed energy deposition (LP-DED) and laser powder bed fusion (L-PBF) are metal AM technologies that have effectively been used to produce a variety of parts for space applications. These technologies have enabled new designs and materials for these applications. The National Aeronautics and Space Administration (NASA) has identified the need to develop and advance new materials in unique space applications such as high-pressure hydrogen environments. One such metal alloy being developed for these applications is NASA HR-1. A high-strength Fe-Ni based superalloy, NASA HR-1 was designed to resist high pressure hydrogen environment embrittlement, oxidation, and corrosion. AM technologies have enabled the manufacturing of NASA HR-1 to be a feasible material for components in hydrogen environments. Development efforts for NASA HR-1 have completed build and heat treatment optimization, material characterization, thermophysical property testing, and mechanical testing in air and hydrogen environments to mature the understanding of the material. This presentation will summarize the development of NASA HR-1 for AM including composition and heat treatment optimization, microstructure characterization, and results of mechanical testing in air and high pressure hydrogen.

Additive Manufacturing↗

NASA NTRS2004

Analysis of Stainless Steel Sandwich Panels with a Metal Foam Care for Lightweight Fan Blade Design

The quest for cheap, low density and high performance materials in the design of aircraft and rotorcraft engine fan and propeller blades poses immense challenges to the materials and structural design engineers. Traditionally, these components have been fabricated using expensive materials such as light weight titanium alloys, polymeric composite materials and carbon-carbon composites. The present study investigates the use of P sandwich foam fan blade made up of solid face sheets and a metal foam core. The face sheets and the metal foam core material were an aerospace grade precipitation hardened 17-4 PH stainless steel with high strength and high toughness. The stiffness of the sandwich structure is increased by separating the two face sheets by a foam core. The resulting structure possesses a high stiffness while being lighter than a similar solid construction. Since the face sheets carry the applied bending loads, the sandwich architecture is a viable engineering concept. The material properties of 17-4 PH metal foam are reviewed briefly to describe the characteristics of the sandwich structure for a fan blade application. A vibration analysis for natural frequencies and P detailed stress analysis on the 17-4 PH sandwich foam blade design for different combinations of skin thickness and core volume %re presented with a comparison to a solid titanium blade.

Min, James B.↗

NASA NTRSDate not supplied

Maturation of Additive Manufactured Aerospace Alloys and Development of Mechanical and Thermophysical Properties for Space Applications

The National Aeronautics and Space Administration (NASA) has been involved in the development and maturation of metal additive manufacturing (AM) for space applications since the late 2000’s. Several efforts have focused on the understanding of AM processes through design optimization, component fabrication, material characterization, testing, standards development, and infusion into propulsion development for flight applications. NASA and partners have matured commonly used aerospace alloys from various alloy families (Nickel, Steel, Iron, Aluminum, and Titanium) and AM processes. An extensive effort has been ongoing between NASA, industry partners, and academia to complete detailed AM process and heat treatment characterization, in addition to generating temperature-dependent mechanical and thermophysical properties. This presentation highlights the characterization and property results using laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes among various alloys. In addition to commonly used alloys, there is a need for ongoing AM optimized alloys using integrated computational materials engineering (ICME) and process development for high performance applications. The applications targeted are launch vehicles, liquid rocket engines, advanced propulsion systems, advanced power systems, and in-space propulsion with high heat fluxes, high pressure, and that utilize propellants such as hydrogen, which can degrade alloys. This presentation will also discuss some of the ongoing novel alloy development and maturation using AM for use in these harsh environments, such as GRCop-42, GRCop-84, NASA HR-1, and C-103. The results from these processes have demonstrated that AM can enable rapid development and new AM optimized alloys can yield higher performance. These alloys have undergone modeling, fundamental metallurgical evaluations, heat treatment studies, and microstructure characterization and mechanical testing campaigns. This, combined with direct application-specific component fabrication and hot-fire testing, can enable the increase of the Technology Readiness Level (TRL) through high duty-cycle testing. This presentation provides a background and overview of these various common and AM-enabled alloys and processing developments including the initial effort related to metallurgical, mechanical, and thermophysical property studies. It also covers the latest advancement in the parallel component development, hot-fire testing, and future developments for these alloys.

Additive Manufacturing↗

NASA NTRS1975

Design study of structural concepts for an arrow-wing supersonic-cruise aircraft

An analytical study was performed to determine the best structural approach for design of primary wing and fuselage structure of a Mach number 2.7 arrow-wing supersonic cruise aircraft. Concepts were evaluated considering near-term start-of-design. Emphasis was placed on the complex interactions between thermal stress, static aeroelasticity, flutter, fatigue and fail-safe design, static and dynamic loads, and the effects of variations in structural arrangements, concepts and materials on these interactions. Results indicate that a hybrid wing structure incorporating low-profile convex-beaded and honeycomb sandwich surface panels of titanium alloy 6Al-4V were the most efficient. The substructure includes titanium alloy spar caps reinforced with Boron-polyimide composites. The fuselage shell is a closed-hat stiffened skin and frame construction of titanium alloy 6Al-4V. This paper presents an executive summary of the study effort, and includes a discussion of the overall study logic, design philosophy and interaction between the analytical methods for supersonic cruise aircraft design.

Sakata, I. F.↗

NASA NTRS1994

High Performance Arcjet Engines

This effort sought to exploit advanced single crystal tungsten-tantalum alloy material for fabrication of a high strength, high temperature arcjet anode. The use of this material is expected to result in improved strength, temperature resistance, and lifetime compared to state of the art polycrystalline alloys. In addition, the use of high electrical and thermal conductivity carbon-carbon composites was considered, and is believed to be a feasible approach. Highly conductive carbon-carbon composite anode capability represents enabling technology for rotating-arc designs derived from the Russian Scientific Research Institute of Thermal Processes (NIITP) because of high heat fluxes at the anode surface. However, for US designs the anode heat flux is much smaller, and thus the benefits are not as great as in the case of NIITP-derived designs. Still, it does appear that the tensile properties of carbon-carbon can be even better than those of single crystal tungsten alloys, especially when nearly-single-crystal fibers such as vapor grown carbon fiber (VGCF) are used. Composites fabricated from such materials must be coated with a refractory carbide coating in order to ensure compatibility with high temperature hydrogen. Fabrication of tungsten alloy single crystals in the sizes required for fabrication of an arcjet anode has been shown to be feasible. Test data indicate that the material can be expected to be at least the equal of W-Re-HfC polycrystalline alloy in terms of its tensile properties, and possibly superior. We are also informed by our colleagues at Scientific Production Association Luch (NP0 Luch) that it is possible to use Russian technology to fabricate polycrystalline W-Re-HfC or other high strength alloys if desired. This is important because existing engines must rely on previously accumulated stocks of these materials, and a fabrication capability for future requirements is not assured.

Kennel, Elliot B.↗

NASA NTRS1987

Thermal analysis and design of a cooling system for a Mach 14 nozzle

The analysis and design of a Mach 14 converging diverging nozzle wall liner is provided. The analysis indicates that: no fin on the coolant side of the nozzle wall is optimum, the thermal stresses are dominant, and the critical area is very near the throat. The molybdenum alloy TZM, with a wall thickness of 2.0 mm in the throat area, appears to be the only material capable of meeting design requirements. Additionally, cooling water at 2000 psia with a flow velocity of 25 m/s in the coolant passages is required.

Mullisen, Ronald↗

NASA NTRSDate not supplied

Crystal Growth in the SUBSA furnace in MSG: 2002 to 2022

In 2002, the investigation “Solidification Using a Baffle In Sealed Ampoules (SUBSA)” was the first investigation to utilize the Microgravity Science Glovebox (MSG) Facility on the International Space Station (ISS). The SUBSA furnace was designed for growth of indium antimonide. It features a transparent section, which allows a side view of the melt, the solid-liquid (SL) interface and the growing crystal. In 2002, four Te-doped and three Zn-doped InSb crystals were grown in microgravity. Subsequently, the SUBSA furnace was used in several materials science investigations, including growing the radiation detector materials, InI and Cs2LiYCl6:Ce from the melt and vapor phase (2017 to 2019) and “Brazing of Aluminum alloys in Space (BRAINS)”. A review of the SUBSA furnace features and parameters will be presented, including the design of the growth ampoules, charge preparation, and the procedures used to grow InSb (in 2002) and InI (in 2019).

Aleksandar Ostrogorsky↗

NASA NTRSDate not supplied

Crystal Growth in the SUBSA furnace at the International Space Station (ISS)

In 2002, our investigation Solidification Using a Baffle In Sealed Ampoules (SUBSA) was the first investigation to utilize the Microgravity Science Glovebox (MSG) Facility on the International Space Station (ISS). The SUBSA furnace was designed for growth of indium antimonide. It features a transparent section, which allows a side view of the melt, the solid-liquid (SL) interface and the growing crystal. In 2002, four Te- doped and three Zn-doped InSb crystals were grown in microgravity. Subsequently, the SUBSA furnace was used in several other materials science investigations, including growing the radiation detector materials InI and Cs2LiYCl6:Ce from the melt and vapor phase (2017 to 2019) and Brazing of Aluminum alloys in Space (BRAINS). A review of the SUBSA furnace features and parameters will be presented, including the design of the growth ampoules, charge preparation, and the procedures used to grow InSb (in 2002) and InI (in 2019).

A.G. Ostrogorsk↗

NASA NTRS2001

A Thin Film Multifunction Sensor for Harsh Environments

The status of work at NASA Glenn Research Center to develop a minimally intrusive integrated sensor to provide realtime measurement of strain, heat flux and flow in high temperature environments is presented in this paper. The sensor can be beneficial as a single package to characterize multiple stress and strain modes simultaneously on materials and components during engine development and validation. A major technical challenge is to take existing individual gauge designs and modify them into one integrated thin film sensor. Ultimately, the goal is to develop the ability to deposit the sensors directly onto internal engine parts or on a small thin substrate that can be attached to engine components. Several prototype sensors constructed of platinum, platinum-rhodium alloy, and alumina on constant-strain alumina beams have been built and bench-tested. The technical challenges of the design. construction, and testing are discussed. Data from the preliminary testing of the sensor array is presented. The future direction for the sensor development is discussed as well.

Wrbanek, John D.↗

NASA NTRS1936

A comparison of corrosion-resistant steel (18 percent chromium - 8 percent nickel) and aluminum alloy (24st)

In the selection of materials for aircraft application, it is not enough to make the selection on a strength-weight basis alone. A strength-weight comparison is significant but other factors must be considered, for while a material with a high ratio of strength to weight may be perfectly satisfactory for one use, it may be totally unfitted for another. It is essential, among other things, that the probable nature, magnitude, and direction of the principal stresses be given special consideration. The following analysis has therefore been made with this in mind. An attempt has been made to cover insofar as possible the major, but not all the points, that a designer would consider in the use of "18-8", as it is commonly referred to, and 24ST aluminum alloy, as applied to aircraft. 24ST was selected for this comparison as it has practically replaced 17ST for aircraft construction and it appears to have the best combination of properties of the alloys now available for this purpose. The cost of fabrication has not been considered.

Sullivan, J E↗

NASA NTRSDate not supplied

Optimization of Rocket Engine Components using Multi-Metallic Additive Manufacturing

Additive manufacturing (AM) is advancing many applications of component design for liquid rocket engines. AM has been demonstrated in various rocket component applications using a variety of monolithic metal alloys, many of which are traditional alloys for extreme environments. NASA and industry partners have focused in recent years to advance processing to create bimetallic and multicomponent AM processes and materials. The role of multi-metallic AM offers advantages since it can further optimize weight, optimize reliability and performance by increasing the strength to weight ratio of a component, and can optimize materials for various engineering requirements. NASA’s Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) project has designed and manufactured a series of additively manufactured (AM) coupled combustion chambers, nozzles, and other engine components to advance new AM processes and materials with the goal of reducing cost and schedule for engine manufacturing. These designs incorporated multimetallic AM, which further enabled carbon-fiber composite overwrap to reduce overall thrust chamber assembly (TCA) mass. Various AM processes were demonstrated on these components using a copper-based alloy/superalloy bimetallic solution. The AM processes being explored individually and in combination for bimetallic applications include Laser Powder Bed Fusion (L-PBF), Laser Powder Directed Energy Deposition (LP-DED), and cold spray. The combination of bimetallic material combinations explored in this research include GRCop-based alloys and superalloys, Inconel 625 or NASA HR-1. One unique development that will be presented is the combustion chamber and nozzle as a single component by using freeform integrated DED to build the nozzle directly onto the aft end of the chamber. The various aspects of the additive manufacturing processes and challenges, materials characterization and mechanical testing, and hot-fire testing of bimetallic components in a relevant rocket engine environment will be discussed.

Additive Manufacturing↗

NASA NTRSDate not supplied

Method Development for Experimental Characterization of Dynamic Strength of Aluminum Structures

Space Flight Hardware (SFH) experiences intense vibratory loading during flight, which only lasts a few minutes. When determining the appropriate size of these components to withstand such loading without becoming damaged, standard design practice is to assume that the peak dynamic loads are applied statically. In doing so, the resulting stress is compared against a material strength parameter obtained from a quasi-static experiment. Since the near-peak stresses are only experienced over a small fraction of time in reality, this approach leads to design conservatism that unnecessarily increases structural mass as well as the associated inefficiency and financial cost. In an effort to modernize engineering design standards to appropriately consider the higher practical strength of dynamically loaded structures, this overarching research project seeks to develop an experimental test procedure for quantifying the dynamic strength of metallic alloys as a function of excitation frequency. In the ideal case, the characterization test would include an in-situ method for monitoring the onset and progression of plastic deformation of the test specimen undergoing vibratory loading. These new tests are designed to be high intensity (forcing amplitude), short term (60 seconds at full amplitude), and cyclic in nature (sinusoidal excitation via attached stinger to an otherwise cantilevered beam). In addition, the initial alloy under investigation is 6061 aluminum, due to its wide use and applicability for SFH. Thus far, the primary candidate under development with live-capacity is to track hysteresis behavior of the beam from power dissipation trends, calculated via force (from transducer on excitation stinger) and velocity (measurements from Laser Doppler Vibrometer) data and work to distinguish between elastic and plastic features. As a key component of this ongoing method development, any pseudo-live indication of plasticity could be corroborated against the outcome of a pre-post assessment of damage via macroscopic evaluation of beam geometry (i.e. assessing any permanent change in the beam’s tip deflection). Support for experimental design decisions as well as dynamic strength data from tests with excitation frequencies of 10, 40, and 55 Hz will be discussed. This work contributes to the foundation for a new type of vibration-based characterization experiments and generates initial data on the functional strength of 6061 aluminum under the conditions considered.

vibrations, plastic deformation, aluminum, testing↗

NASA NTRS1969

Welded repairs of punctured thin-walled aluminum pressure vessels

Punctures in thin-walled aluminum pressure vessels are repaired by plugging the hole with an interference-fit disc and welding the unit. The repaired vessels withstood test pressures in excess of vessel ultimate design values for 2-, 4-, and 6-inch holes in 0.202-inch-thick aluminum alloy parent material.

Jones, D. J.↗

NASA NTRS1977

Thermal barrier coating on high temperature industrial gas turbine engines

The thermal barrier coating used was a yttria stabilized zirconia material with a NiCrAlY undercoat, and the base engine used to establish improvements was the P&WA FT50A-4 industrial gas turbine engine. The design benefits of thermal barrier coatings include simplified cooling schemes and the use of conventional alloys in the engine hot section. Cooling flow reductions and improved heating rates achieved with thermal barrier coating result in improved performance. Economic benefits include reduced power production costs and reduced fuel consumption. Over the 30,000 hour life of the thermal barrier coated parts, fuel savings equivalent to $5 million are projected and specific power (megawatts/mass of engine airflow) improvements on the order of 13% are estimated.

Carlson, N.↗

NASA NTRS1978

Thermomechanical processing of HAYNES alloy No. 188 sheet to improve creep strength

Improvements in the low strain creep strength of HAYNES alloy No. 188 thin gauge sheet by means of thermomechanical processing were developed. Processing methods designed to develop a sheet with strong crystallographic texture after recrystallization and to optimize grain size were principally studied. The effects of thickness-to-grain diameter ratio and prestrain on low strain creep strength were also briefly examined. Results indicate that the most significant improvements were obtained in the sheets having a strong crystallographic texture. The low strain creep strength of the textured sheets was observed to be superior to that of standard production sheets in the 922 K to 1255 K temperature range. Tensile, stress rupture, fabricability, and surface stability properties of the experimental sheets were also measured and compared to property values reported for the baseline production sheets.

Klarstrom, D. L.↗

NASA NTRS1981

Vacuum pumping system for spaceborne passive hydrogen masers

The ultimate utility of hydrogen masers as highly accurate clocks aboard navigation satellites depends on the feasibility of making the maser lightweight, compact, and capable of a 5 to 7 year unattended operation. A vacuum pumping system for the maser that is believed to meet these criteria was designed and fabricated. The pumping system was fabricated almost completely from 6Al-4V titanium alloy and incorporates two or four sintered zirconium carbon getter pumps with integral activation heaters. The manner in which the getter pumps were mounted to insure that they will stand both the activation and the shock of launch is illustrated. Data on the total hydrogen capacity and pumping of this system is also presented.

Wolf, S. A.↗