Search NASA⌕ Search

SEARCH · Search NASA

Results for “Bonded Joints”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Mechanistic Models of Friction Stir Welding

Friction stir welding is a welding process developed at The Welding Institute (TWI) in England. The method uses very large strain plastic deformation of the material to join two pieces of metal together. The material is deformed using a tool which is forced between the two pieces which rotates causing a bond. Beyond this, very little is actually known although many people working in the field are willing to speculate on the detailed mechanisms involved. Some measurements made using sacrificial thermocouples at the weld joint indicate that the maximum temperature during the weld process is on the order of 370C - well below the melting temperature of the material. However, at this temperature, the material properties are highly temperature dependent, and the yield stress is approximately an order of magnitude less at this temperature than it is at room temperature. As expected, there are many interpretations of the physical mechanisms occurring during the weld process. Although there is very little published concerned with FSW, some of the anecdotal theories will be described. One describes the primary mechanism as frictional heating at the front of the tool caused by slip between the tool and the material. At elevated temperatures, the weld material becomes soft and deforms around the tool but not essentially altered by the tool rotation, similar to an extrusion. As the material meets again at the rear of the tool, the temperatures and pressures are sufficient to cause the material to bond. All other structures seen are secondary and unimportant. Another theory examined last summer at NASA's Marshall Space Flight Center (MSFC) was that there was no slip between the tool and the material resulting in a rotating mass of plastic weld material traveling at a variety of angular velocities - the greatest at the tool surface diminishing to zero at the outer edge of the plastic mass surrounding the tool. This conceptual model was followed by simplified calculations which showed that the balance of moments through the weld plug was not possible under steady state conditions and realistic temperature profiles. This led to some consideration of a quasi-steady oscillating process. Later when force measurements became available some models were modified and new ones were proposed.

Stewart, Michael B.↗
NASA NTRSDate not supplied

Modified Epoxy Matrix Resins for Reduced Dependence on Redundant Fasteners in Secondary-Bonded Composite Structures

In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination that can lead to weak bonds. No methods currently exist to measure the strength of an adhesive bond nondestructively. For these reasons, regulating organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to achieve certification for civil transport aircraft. To meet this requirement, manufacturers commonly install redundant fasteners (~105 fasteners in a twin-aisle airframe with composite fuselage and wings), which add tremendous complexity, time and cost, and significantly reduce performance of the airframe. Under NASA’s Convergent Aeronautics Solutions (CAS) Program, the Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy matrix resins to enable reflow and diffusion of the resin at the interface during a secondary bonding/cure process. The mixing process eliminates the material discontinuity at the interface, thereby removing the dependence of bond performance on adhesion across a nearly two-dimensional boundary. The AERoBOND interface is similar to the interlaminar region formed during a co-cure process, so joint performance depends on the cohesive properties of the matrix resin, which can be measured, inspected non-destructively, and certified for flight with fewer redundant fasteners. This presentation describes the ongoing development of stoichiometrically-offset epoxy resins to control the degree of cure in composite joints and enable interfacial mixing during secondary bonding/curing. Details on the resin formulation, laminate fabrication, and mechanical testing will also be presented. The precracked mode-II fracture toughness measured from preliminary AERoBOND joints was similar for joints fabricated with conventional epoxy matrix materials.

thermoset, hardener, prepreg, assembly↗
NASA NTRS1986

Nondestructive evaluation of adhesive bond strength using the stress wave factor technique

Acousto-ultrasonic nondestructive evaluation has been conducted to evaluate the adhesive bond strength between rubber and steel plates using the stress wave factor (SWF) measurement technique. Specimens with different bond strength were manufactured and tested using the SWF technique. Two approaches were used to define the SWF. One approach defines the SWF as the signal energy and the other approach defines the SWF as the square root of the zero moment of the frequency spectrum of the received signal. The strength of the rubber-steel adhesive joint was then evaluated using the destructive peel strength test method. It was observed that in both approaches higher values of the SWF measurements correspond to higher values of the peel strength test data. Therefore, these results show that the stress wave factor technique has the potential of being used in quality assurance of the adhesive bond strength between rubber and steel substrates.

Dos Reis, Henrique L. M.↗
NASA NTRS1979

A critical examination of stresses in an elastic single lap joint

The results of an approximate nonlinear finite-element analysis of a single lap joint are presented and compared with the results of a linear finite-element analysis, and the geometric nonlinear effects caused by the load-path eccentricity on the adhesive stress distributions are determined. The results from finite-element, Goland-Reissner, and photoelastic analyses show that for a single lap joint the effect of the geometric nonlinear behavior of the joint has a sizable effect on the stresses in the adhesive. The Goland-Reissner analysis is sufficiently accurate in the prediction of stresses along the midsurface of the adhesive bond to be used for qualitative evaluation of the influence of geometric or material parametric variations. Detailed stress distributions in both the adherend and adhesive obtained from the finite-element analysis are presented to provide a basis for comparison with other solution techniques.

Cooper, P. A.↗
NASA NTRS1987

Attaching Copper Wires to Magnetic-Reed-Switch Leads

Bonding method reliably joins copper wires to short iron-alloy leads from glass-encased dry magnetic-reed switch without disturbing integrity of glass-to-metal seal. Joint resistant to high temperatures and has low electrical resistance.

Kamila, Rudolf↗
NASA NTRSDate not supplied

Joining and Integration of Silicon Carbide-Based Ceramic Materials for Aerospace Applications: An Overview

In order to fully utilize silicon carbide-based ceramics and ceramic matrix composites (CMCs) for aerospace and ground based applications, advanced joining and integration technologies are critically needed for achieving large, complex shaped, and integrated components. Careful material selection of joining inter-layers needs to consider chemical and thermal compatibilities with the parent materials that are being joined. Also, optimization needs to be conducted to select the proper processing conditions for achieving robust joints that are well adhered, strong, uniform, crack free, and have minimal residual stresses. NASA GRC developed pressureless and pressure aided approaches for joining ceramics and CMCs include brazing, diffusion bonding, refractory eutectic phase joining, and Single-step Elevated Temperature (SET) Joining. For joining ceramics and CMCs to metals, several brazes have been utilized. Brazing approaches for joining ceramics and metals have also included tailored brazes with multiple interlayers and particle additions. An overview of the joining approaches will be provided. In addition, processing-microstructure-property relationships will be discussed.

Silicon carbide↗
DOE OSTI2022

Niobium to Titanium Electron Beam Welding for SRF Cavities

Titanium and niobium are the main materials used for the fabrication of Superconducting Radio Frequency (SRF) cavities. These two metals are usually joined , using various welding techniques, using a third material in between. This contribution focuses on the development of an innovative electron beam welding technique capable of producing a strong bond between these two different materials. Several samples are produced and tested to assess the mechanical strength at room and cryogenic temperature as well as the composition of the resulting welded joint. Also, the first units of the Single Spoke Resonator type 2 (SSR2) cavities for the Proton Improvement Plan-II (PIP-II [1]) have been fabricated joining directly various grades of titanium to niobium and results gathered through the fabrication will be reported.

43 PARTICLE ACCELERATORS↗
NASA NTRS2015

High Temperature Joining and Characterization of Joint Properties in Silicon Carbide-Based Composite Materials

Advanced silicon carbide-based ceramics and composites are being developed for a wide variety of high temperature extreme environment applications. Robust high temperature joining and integration technologies are enabling for the fabrication and manufacturing of large and complex shaped components. The development of a new joining approach called SET (Single-step Elevated Temperature) joining will be described along with the overview of previously developed joining approaches including high temperature brazing, ARCJoinT (Affordable, Robust Ceramic Joining Technology), diffusion bonding, and REABOND (Refractory Eutectic Assisted Bonding). Unlike other approaches, SET joining does not have any lower temperature phases and will therefore have a use temperature above 1315C. Optimization of the composition for full conversion to silicon carbide will be discussed. The goal is to find a composition with no remaining carbon or free silicon. Green tape interlayers were developed for joining. Microstructural analysis and preliminary mechanical tests of the joints will be presented.

Joining↗
NASA NTRS1982

Bonding procedure for Teflon seals

Material and bonding procedures designed for use as seals at the National Transonic Facility at the NASA Langley Research Center are presented. Teflon TFE was chosen for its ability to withstand pressures of up to 130 psi and temperatures ranging from -320 to 150 F, in addition to tolerances of 0.074 in. and having a movement allowance of 0.75 in. during transient cycles. Since some of the seals are 14 in. in diameter, Teflon sheets had to be sliced and bonded together after machining to size, resulting in seals with circular, oval, straight, and rectangular cross sections. Step-by-step preparation procedures are provided, and it is noted that the scarf joints performed as predicted during tests.

Barringer, S. R.↗
NASA NTRS2021

Machine Learning to Predict Joint Performance in Epoxy Composites Based on Process Parameters

Polymer matrix composites are gaining popularity in the aerospace industry due to their high specific strength, fatigue properties, and processability. However, based on current FAA certification guidelines, manufacturers utilizing current state-of-the-art composites made with adhesive bonds commonly install redundant fasteners to guarantee the strength of these adhesively bonded composite parts. The number of fasteners in a single-aisle commercial transport aircraft is typically on the order of 105, which reduces manufacturing rate, increases cost tremendously, and reduces the advantage of the specific strength composites provide. Due to this, the Adhesive Free Bonding of Composites (AERoBOND) project at NASA Langley Research Center has developed a novel assembly process to manufacture complex composite parts without the use of adhesives and fasteners. However, optimization of the process is currently challenging due to the complex and interdependent process parameters. To assist with the optimization, four machine learning algorithms utilizing gradient boosting decision trees were created to provide predictions for the mechanical and characterization properties of the composite parts. Approximately 200 random states from each algorithm were tested, and the models from each state were isolated and analyzed based on their accuracy, a validation process, and their feature importance. This analysis concluded that the models created from the machine learning algorithms could accelerate a parametric study for the AERoBOND process by rapidly optimizing process parameters to achieve desired performance characteristics.

Brennen Michael Middleton↗
NASA NTRSDate not supplied

Machine Learning to Predict Joint Performance in Epoxy Composites Based on Process Parameters

Polymer matrix composites are gaining popularity in the aerospace industry due to their high specific strength, fatigue properties, and processability. However, based on current FAA certification guidelines, manufacturers utilizing current state-of-the art composites made with adhesive bonds commonly install redundant fasteners to guarantee the strength of these adhesively bonded composite parts.1,2 The number of fasteners in a single-aisle commercial transport aircraft is typically on the order of 105, which reduces manufacturing rate, increases cost tremendously, and reduces the advantage of the specific strength composites provide. Due to this, the Adhesive Free Bonding of Composites (AERoBOND) project at NASA Langley Research Center has developed a novel assembly process to manufacture complex composite parts without the use of adhesives and fasteners.1 However, optimization of the process is currently challenging due to the complex and interdependent process parameters. To assist with the optimization, four machine learning algorithms utilizing gradient boosting decision trees were created to provide predictions for the mechanical and characterization properties of the composite parts. Approximately 200 random states from each algorithm were tested, and the models from each state were isolated and analyzed based on their accuracy, a validation process, and their feature importance. This analysis concluded that the models created from the machine learning algorithms could accelerate a parametric study for the AERoBOND process by rapidly optimizing process parameters to achieve desired performance characteristics.

Brennen M Middleton↗
DOE OSTI2022

Subcomponent Validation of Composite Joints for Marine Energy Structures

The Marine Energy Advanced Materials project addresses the barriers and uncertainties facing marine renewable energy developers in using composite materials for load-bearing structures. Sponsored by the U.S. Department of Energy's Water Power Technologies Office, the multiyear project comprises of collaborators from the National Renewable Energy Laboratory (NREL), Sandia National Laboratories, Pacific Northwest National Laboratory (PNNL), Montana State University (MSU), Florida Atlantic University (FAU), and industry stakeholders. As part of the Marine Energy Advanced Materials project, marine renewable energy industry surveys and assessments were conducted to identify key materials and knowledge gaps that hinder the adoption of composite materials in marine renewable energy structures. Specific knowledge gaps highlighted for composite materials were environmental effects, fatigue strengths, and bonded and bolted interconnects (composite/composite and composite/metal). It was concluded that many of these gaps could be addressed through subcomponent validation; consequently, a program was developed at NREL with the goals of developing subcomponent validation methods for appropriate marine energy materials, which would improve the understanding of design allowables for full-scale structural components and joints. Ultimately, the aim is to reduce timelines and costs associated with full-scale structural validation efforts while also providing near-net-scale static and fatigue data of composite/metal subcomponents for marine renewable energy systems. To approach these goals, a testing program was developed at NREL to investigate a variety of materials and structural design details at the subcomponent scale to understand (a) the effects of harsh and corrosive marine energy environments and (b) the static and fatigue strengths of the complex geometries. The recent study from this testing program is perhaps the largest that has ever been conducted with respect to specimen scale and geographic diversity of underwater environmental conditions that the specimens were subjected to. A variety of specimen geometries were designed by NREL to highlight key features of multimaterial (composite/composite or metal/composite) interconnects that may be used in marine renewable energy structural designs. The designs used several different composite matrices, adhesives, and marine-grade steels, which were highlighted in the surveys as being the most appropriate for harsh marine environments. Composite panels were then manufactured at MSU, and were subsequently manufactured into test specimens by NREL. The specimens were shipped to FAU and PNNL for conditioning in ocean water tanks at various temperatures for an extended period. The specimens were then returned to NREL for structural validation. This presentation will provide an overview of recent advances within the testing program in terms of specimen design and test methods, and will discuss results and key findings of the subcomponent testing program to date at NREL.

adhesives↗
DOE OSTI2020

What are the current limits on determination of protonation state using neutron macromolecular crystallography?

The rate of deposition of models determined by neutron diffraction, or a hybrid approach that combines X-ray and neutron diffraction, has increased in recent years. The benefit of neutron diffraction is that hydrogen atom (H) positions are detectable, allowing for the determination of protonation state and water molecule orientation. This study analyses all neutron models deposited in the Protein Data Bank to date, focusing on protonation state and properties of H (or deuterium, D) atoms as well as the details of water molecules. In particular, clashes and hydrogen bonds involving H or D atoms are investigated. As water molecules are typically the least reproducible part of a structural model, their positions in neutron models were compared to those in homologous high-resolution X-ray structures. For models determined by joint refinement against X-ray and neutron data, the water structure comparison was also carried out for models re-refined against the X-ray data alone. The homologues have generally fewer conserved water molecules where X-ray only was used and the positions of equivalent waters vary more than in the case of the hybrid X-ray model. As neutron diffraction data are generally less complete than X-ray data, the influence of neutron data completeness on nuclear density maps was also analyzed. Here, we observe and discuss systematic map quality deterioration as result of data incompleteness.

Hydrogen bond↗
DOE OSTI2021

Leveraging observed soil heterotrophic respiration fluxes as a novel constraint on global-scale models

Microbially-explicit models may improve understanding and projections of carbon dynamics in response to future climate change, but their fidelity in simulating global-scale soil heterotrophic respiration (RH), a stringent test for soil biogeochemical models, has never been evaluated. We used statistical global RH products, as well as 7,821 daily site-scale RH measurements, to evaluate the spatio-temporal performance of one first-order decay model (CASA-CNP) and two microbially-explicit biogeochemical models (CORPSE and MIMICS) that were forced by two different climate datasets. CORPSE and MIMICS did not provide any measurable performance improvement; instead, the models were highly sensitive to the meteorological input data used to drive them. Spatial RH variability was generally well simulated except in the northern middle latitudes (~50°N) and arid regions; models captured the seasonal variability of RH well, but showed more divergence in tropic and arctic regions. Our results demonstrate that the next generation of biogeochemical models shows promise, but also needs to be improved for realistic spatio-temporal variability of RH. Finally, we emphasize the importance of net primary production, soil moisture, and soil temperature inputs, and that jointly evaluating soil models for their spatial (global scale) and temporal (site scale) performance provides crucial benchmarks for improving biogeochemical models.

Jian, Jinshi↗
DOE OSTI2022

Experiments and modelling of adhesive failure initiation of an epoxy underfill: a study of electronic packaging survivability

Epoxy underfills can be implemented in electronic packaging to enhance solder joint reliability of surface mounted components. However, it is important for an engineer to have a failure criterion that can be used for failure predictions and redesign of electronic assemblies. For this study, data from epoxy bond failure in mock electronic part assemblies were correlated to finite element analyses to predict adhesive failure initiation. Experiments were performed to determine failure loads for various loading locations and nonlinear viscoelastic analyses were performed for the same loading locations to determine a maximum principal strain failure parameter. Predictions showed that a maximum principal strain failure parameter defined from one test could be used as an indicator of adhesive failure of an epoxy bond undergoing other modes of loading. Failure initiation predictions matched experimental data using a maximum principal strain failure parameter for an epoxy bond undergoing mixed modes of loading for both unfilled and alumina oxide filled 828DEA epoxy. Such experimental setup is deemed appropriate for future epoxy testing.

42 ENGINEERING↗
NASA NTRS1976

Capillary flow weld-bonding

The invention of a weld-bonding technique for titanium plates was described. This involves fastening at least two plates of titanium together using spot-welding and applying a bead of adhesive along the edge of the resistance spot-welded joint which upon heating, flows and fills the separation between the joint components.

Vaughan, R. W.↗