Search NASA⌕ Search

SEARCH · Search NASA

Results for “CHEMICAL EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Venusian atmospheric equilibrium chemistry at the Pioneer Venus anomalous event altitude

No convincing explanation for the anomalous behavior of the Atmospheric Structure Experiment temperature sensors at approximately 13 km altitude has been found. It occurred on all of the widely-spaced probes, in a similar fashion. A preliminary effort has been made to determine atmospheric chemical species which might be present at 13 km. The purpose of this effort is to initiate suggestions of possible chemical interactions and to explore the effects of the presence of possible metal reactants including condensation. Equilibrium fractions of chemical species were calculated at a variety of conditions. Baseline calculations were made for the altitudes near 13 km. For comparison calculations were also made at 13 km but with the introduction of plausible metal atoms.

Craig, Roger A.↗
NASA NTRS2019

Comparison of Neutral Outgassing of Comet 67P/Churyumov-Gerasimenko Inbound and Outbound Beyond 3 Au From ROSINA/DFMS

Context. Pre-equinox measurements of comet 67P/Churyumov-Gerasimenko with the mass spectrometer ROSINA/DFMS on board the Rosetta spacecraft revealed a strongly heterogeneous coma. The abundances of major and various minor volatile species were found to depend on the latitude and longitude of the nadir point of the spacecraft. The observed time variability of coma species remained consistent for about three months up to equinox. The chemical variability could be generally interpreted in terms of surface temperature and seasonal effects superposed on some kind of chemical heterogeneity of the nucleus. Aims. We compare here pre-equinox (inbound) ROSINA/DFMS measurements from 2014 to measurements taken after the outbound equinox in 2016, both at heliocentric distances larger than 3 AU. For a direct comparison we limit our observations to the southern hemisphere. Methods. We report the similarities and differences in the concentrations and time variability of neutral species under similar insolation conditions (heliocentric distance and season) pre- and post-equinox, and interpret them in light of the previously published observations. In addition, we extend both the pre- and post-equinox analysis by comparing species concentrations with a mixture of CO2 and H2O. Results. Our results show significant changes in the abundances of neutral species in the coma from pre- to post-equinox that are indicative of seasonally driven nucleus heterogeneity. Conclusions. The observed pre- and post-equinox patterns can generally be explained by the strong erosion in the southern hemisphere that moves volatile-rich layers near the surface.

comets↗
NASA NTRS1997

Application of Shear Plate Interferometry to Jet Diffusion Flame Temperature Measurements

The recent ban on the production of bromotrifluoromethane (CF3Br) because of its high stratospheric ozone depletion potential has led to interest in finding alternative agents for fire extinguishing applications. Some of the promising alternatives are fluorinated hydrocarbons. A clear understanding of the effects of CF3Br and alternative chemical suppressants on diffusion flames is therefore necessary in the selection of alternative suppressants for use in normal and microgravity. The flame inhibition effects of halogen compounds have been studied extensively in premixed systems. The effect of addition of halocarbons (carbon-halogen compounds) to diffusion flames has been studied experimentally in coflow configurations and in counterflow gaseous and liquid-pool flames. Halogenated compounds are believed to inhibit combustion by scavenging hydrogen radicals to form the relatively unreactive compound HF, or through a catalytic recombination cycle involving HBr to form H2. Comparisons between halogens show that bromine inhibition is significantly more effective than chlorine or fluorine. Although fluorinated compounds are only slightly more effective inhibitors on a mass basis than nitrogen, they are more effective on a volume basis and are easily stored in liquid form. The objectives of this study are (a) to determine the stability limits of laminar jet diffusion flames with respect to inhibitor concentration in both normal and microgravity, and (b) to investigate the structure of halocarbon-inhibited flames. In the initial phase of this project, visual diagnostics were used to observe the structure and behavior of normal and microgravity flames. The initial observations showed significant changes in the structure of the flames with the addition of halocarbons to the surrounding environment, as discussed below. Furthermore, the study established that the flames are more stable relative to the addition of halocarbons in microgravity than in normal gravity. Visual diagnostics of flames are, however, necessarily limited to detection of radiative emission in the visible range, and offer only qualitative information about the nature of the processes in the flame. In particular, the study sought to understand the structure of the inhibitor-perturbed flames with regard to temperature and species concentration in the outer region of the flame. Whereas thermocouple measurements can be used in ground based studies, their implementation in drop-tower rigs is limited. A possible approach to determine the temperature field around the flame is to use interferometric techniques. The implementation and testing of a shear-plate interferometry technique is described below.

VanDerWege, Brad A.↗
NASA NTRS1973

Some analyses of the chemistry and diffusion of SST exhaust materials during phase 3 of the wake period

In the generally stably stratified lower stratosphere, SST exhaust plumes could spend a significant length of time in a relatively undispersed state. This effort has utilized invariant modeling techniques to simulate the separate and combined effects of atmospheric turbulence, turbulent diffusion, and chemical reactions of SST exhaust materials in the lower stratosphere. The primary results to date are: (1) The combination of relatively slow diffusive mixing and rapid chemical reactions during the Phase III wake period minimizes the effect of SST exhausts on O3 depletion by the so-called NOx catalytic cycle. While the SST-produced NO is substantially above background concentrations, it appears diffusive mixing of NO and O3 is simply too slow to produce the O3 depletions originally proposed. (2) The time required to dilute the SST exhaust plume may be a significant fraction of the total time these materials are resident in the lower stratosphere. If this is the case, then prior estimates of the environmental impact of these materials must be revised significantly downward.

Hilst, G. R.↗
NASA NTRS1997

An Overview of the Tropospheric Aerosol Radiative Forcing Observational Experiment

Aerosol effects on atmospheric radiation are a leading source of uncertainty in predicting future climate. As a result, the International Global Atmospheric Chemistry Program has established a Focus on Atmospheric Aerosols (IGAC/FAA) and endorsed a series of aerosol field campaigns. TARFOX, the second in the IGAC/FAA series, was designed to reduce this uncertainty by measuring aerosol properties and effects in the US eastern seaboard, where one of the world's major plumes of industrial haze moves from the continent over the Atlantic Ocean. TARFOX's objectives are to: 1. Make simultaneous measurements of: (a) aerosol effects on radiation fields, and (b) the chemical, physical, and optical properties of the aerosols causing those effects. 2. Perform a variety of closure studies by using overdetermined data sets to test the mutual consistency of measurements and calculations of a wide range of aerosol properties and effects. 3. Use the results of the closure studies to assess and reduce uncertainties in estimates of aerosol radiative forcing, as well as to guide future field programs. An important subset of the closure studies is tests and improvements of algorithms used to derive aerosol properties and radiative effects from satellite measurements. The TARFOX Intensive Field Period (IFP) was conducted July 10-31, 1996. It included coordinated measurements from four satellites (GOES-8, NOAA-14, ERS-2, LANDSAT), four aircraft (ER-2, C-130, C-131, and a modified Cessna), land sites, and ships. A variety of aerosol conditions was sampled, ranging from relatively clean behind frontal passages to moderately polluted with aerosol optical depths exceeding 0.5 at mid-visible wavelengths. The latter conditions included separate incidents of enhancements caused primarily by anthropogenic sources and another incident of enhancement apparently influenced by recent fog processing. Spatial gradients of aerosol optical thickness were sampled to aid in isolating aerosol effects from other radiative effects and to more tightly constrain closure tests, including those of satellite retrievals. This talk gives an overview of TARFOX goals, rationale, methods, and initial key findings.

Russell, P. B.↗
NASA NTRSDate not supplied

Identification and Study of Validation Level Test Cases for Computational Modeling of Non-Charring Ablators

Computational modeling of Thermal Protection System (TPS) materials, used for aerospace applications, provides numerous advantages in preliminary selection and design of a heatshield material and shape for atmospheric entry vehicles. However, to serve as a reliable tool for prediction of material thermal and ablative behavior, the modeling approach needs to be validated against real experimental and flight data, preferably at a range of applied conditions. The validation study is typically very complex as it requires reliable measured data not only for the material thermal response and surface recession, but also well characterized environmental conditions. The validation problem becomes even more complex when the material thermal response is dictated by multi-physics effects such as solid conduction, in-depth thermal decomposition, pyrolysis gas flow and chemical reactions. The multi-physics effects complicate not only the modeling effort, but also the experimental measurement for validation of various aspects of the highly coupled problem. In this study, an attempt is made to identify suitable experimental data that could serve as a source for validation of material thermal response modeling tools. To reduce the computational complexity, this study focuses only on non-charring ablators, where the material thermal response could be modeled with a single governing equation for solid conduction and the ablation is limited only to the surface of the material. With a well characterized and publicly available experimental data being sparse, the study is limited in presenting test cases for only three materials: camphor, graphite and FiberForm® in the sequence of increased modeling complexity. Graphite is a commonly used TPS material for aerospace applications, both for leading edges of high-speed vehicles and internal insulation of solid rocket motors. FiberForm® is a porous carbon pre-form used in preparation of the well known PICA material Tran et al. [1996]. Inclusion of camphor into the list is conditioned with the relative simplicity in modeling the material thermal and chemical response and the low-enthalpy flow environment. In addition, camphor has been used as a simple test material for study of flow transition behavior by Stock and Ginoux [1973] and assessment of a heatshield shape change at flight relevant conditions by Rotondi et al. [2022]. In this work, the identified experimental data was extracted from the public literature and test cases that yet have been published. As it was found from the review, not a single test case contains an exhaustive set of data that would validate every aspect of the material physics. However, in the data collected, various aspects of the material behavior can be still validated, such as surface and in-depth temperature, amount of recession and a shape change. The identified experimental data for each case is accompanied with a characterized flow environment and simulated boundary conditions predicted by a Data-Parallel Line Relaxation (DPLR) code Wright et al. [1998]. In addition, material thermal response numerical simulations in each test case are performed with Kentucky Aerothermodynamics and Thermal Response System (KATS-MR) Zibitsker et al. [2022] providing a comparative study and a sanity check for the proposed validation data. Sample results from the performed numerical study are shown below. Figure 1 shows distribution of surface heat flux and pressure values on a hemi-cylinder model made of FiberForm® and tested in HyMETS arc-jet facility. The results are shown for the high pressure condition among the two tests. Flow simulation was performed with DPLR code on a quarter of original geometry. In the figure, the quarter shape was mirrored across zx and xy planes to show the complete distribution. Figure 2 shows the material response results for the high pressure case (7500 Pa), simulated with KATS-MR and a comparison to the experimental data for the surface temperature and shape shape. The simulation was performed on a 2-D slice, extracted in the xy plane at the middle of the sample. Figure 3 shows the material response simulation for the low pressure case (3500 Pa) and a comparison to the experimental data for surface temperature and shape change.

ablation↗
NASA NTRS1974

The chemistry and diffusion of aircraft exhausts in the lower stratosphere during the first few hours after fly-by

An analysis of the hydrogen-nitrogen-oxygen reaction systems in the lower stratosphere as they are initially perturbed by individual aircraft engine exhaust plumes was conducted in order to determine whether any significant chemical reactions occur, either among exhaust chemical species, or between these species and the environmental ozone, while the exhaust products are confined to intact plume segments at relatively high concentrations. The joint effects of diffusive mixing and chemical kinetics on the reactions were also studied, using the techniques of second-order closure diffusion/chemistry models. The focus of the study was on the larger problem of the potential depletion of ozone by supersonic transport aircraft exhaust materials emitted into the lower stratosphere.

Hilst, G. R.↗
NASA NTRS1998

Substrate Effects on Electronic Properties of Atomic Chains

Atomic chains, precise structures of adatoms created on an atomically regulated surface, are candidates for constituent elements in future electronics. It was predicted that Si chains were metallic and Mg chains were semiconducting, and a doping method was also discussed. The substrate was assumed to work as a non-interacting template holding the adatoms. However, this scheme requires a low-temperature environment so that the adatoms will not displace from their ideal positions due to unwanted thermal agitation. For better structural stability, we may seek a scheme to allow the adatoms to form chemical bonding with the substrate atoms and secure their positions. The chemical bonding has two major effects on the chain electronic properties. First, only the remaining s and p orbitals in an adatom not used for the chemical bonding can decide chain band structures, rather than the full set of orbitals previously assumed. Second, because of a possible HOMO energy difference between adatom and substrate atom, semiconducting chains are unintentionally doped. These effects are studied with a self-consistent tight-binding method with universal parameters. With one adatom per unit cell, adatom chains are semiconducting: (1) if adatoms are of group III and form one chemical bond per adatom, or (2) if adatoms are of group IV and form two chemical bonds. 'Me previous result [I I of realizing semiconducting chains by group II adatoms without chemical bonds is consistent with this picture. When the HOMO energy in an adatom is shallower than that in a substrate atom, the entire chain is positively polarized, unintentionally achieving p-type doping. When deeper, the chain is negatively charged, achieving n-type doping.

Yamada, Toshishige↗
NASA NTRS1997

Premixed Gas Combustion: An Excitable System

Rotating spiral and target patterns have been observed experimentally on freely-propagating premixed gas flames in large diameter tubes at normal gravity (1-g). These modes of propagation occur in near-limit mixtures which have a Lewis number (Le, defined as the ratio of the thermal diffusivity of the cold mixture to the mass diffusivity of the scarce component into the mixture) sufficiently greater than one. However, at 1-g, buoyant flows strongly distort the flame curvature, hydrodynamics (thus stretch) and convective transport of species and heat. In turn, these alter the critical Le required for onset of instability. To isolate and better understand the mechanisms which drive the observed patterns and their dynamics, 1-g and microgravity (micro-g) experiments are being conducted to determine: (1) the structure and dynamics of the patterns, (2) a map of the critical Le and heat loss for their occurrence, (3) the relative significance of the chemical kinetics, and (4) the effect of curvature (local wave and global flame front) on wave propagation. With this in hand, we will be better prepared to discuss an additional mode, a state of 'chemical turbulence,' which seems to be the ultimate fate of many of these near-limit flames prior to extinction.

Pearlman, Howard↗
NASA NTRS1974

Ecological effects and environmental fate of solid rocket exhaust

Specific target processes were classified as to the chemical, chemical-physical, and biological reactions and toxic effects of solid rocket emissions within selected ecosystems at Kennedy Space Center. Exposure of Citris seedlings, English peas, and bush beans to SRM exhaust under laboratory conditions demonstrated reduced growth rates, but at very high concentrations. Field studies of natural plant populations in three diverse ecosystems failed to reveal any structural damage at the concentration levels tested. Background information on elemental composition of selected woody plants from two terrestrial ecosystems is reported. LD sub 50 for a native mouse (peromysous gossypinus) exposed to SRM exhaust was determined to be 50 ppm/g body weight. Results strongly indicate that other components of the SRM exhaust act synergically to enhance the toxic effects of HCl gas when inhaled. A brief summary is given regarding the work on SRM exhaust and its possible impact on hatchability of incubating bird eggs.

Nimmo, B.↗
NASA NTRS1961

Radiation Emission Effects of the Equilibrium Boundary Layer in the Stagnation Region

The laminar compressible boundary layer in chemical equilibrium is analysed to show the effect of emission of radiation by the boundary layer on solutions of the energy equation and on the resulting heat transfer. Solutions are obtained at one flight condition, but for several nose radii, in a regime where absorption is negligible. The consequent effects on heat transfer and boundary-layer thickness are determined. The concept of a separate boundary layer and shock layer is discussed in the light of the results obtained.

Howe, John Thomas↗
NASA NTRS2019

3D Radiative Hydrodynamics Modeling of Convection of Stars to Probe Their Interiors and Photospheric Properties

The dramatic flow of data from the Kepler and K2 missions opens the opportunity to significantly improve our knowledge of stellar interiors, surface dynamics, and structure. However, interpretation of these observations is a challenging task because it depends on tiny effects that can be studied only with advanced first-principles modeling. We present results of 3D time-dependent radiative hydrodynamic simulations of stellar outer convection zones and atmospheres taking into account chemical composition, radiative transfer, turbulence effects, and a realistic equation of state for main sequence stars. We will discuss properties of convective structure and dynamics, convective overshoot, effects of magnetic fields and rotation, as well as the potential influence of turbulent surface dynamics on high-precision RV measurements.

Photospheric↗
NASA NTRS1992

Damage mechanisms in three-dimensional woven reinforced ceramic matrix composites under tensile and flexural loading at room and elevated temperatures

Three-dimensional Nicalon SiC/SiC matrix composites made through a chemical vapor infiltration process were studied under tensile and flexural loading at 23, 1200, and 1550 C in air. In situ damage accumulation monitoring NDE techniques were utilized to identify failure mechanisms in these materials. The effectiveness and durability of a chemical vapor deposition SiC surface coating were also evaluated in severe oxidizing environment. Results show that the failure response was very similar for the 23 and 1200 C specimens, while at 1550 C there were significant changes in both the composite mechanical behavior and the matrix microstructure. Extensive fiber pull-out was observed only in the 1550 C specimen. It is also found that the SiC surface coating can protect the composite up to the critical matrix cracking strength.

Chulya, Abhisak↗
NASA NTRS1998

Effect of Fresh Poultry Litter and Compost on Soil Physical and Chemical Properties

Application of poultry litter and compost as a substitute for fertilizer not only uses unwanted waste and decreases expenditures for commercial fertilizer, it adds nutrients to soil for plant uptake. The properties of soil affected by poultry litter were analyzed to determine the positive and negative aspects of using this substitute fertilizer. This study focused on changes associated with saturated hydraulic conductivity, bulk density, nitrate concentrations, and pH after application of varying concentrations of poultry litter and compost. Soil samples from Tennessee Valley Substation in Alabama were analyzed in a laboratory at Alabama A&M University. As a result of the application of fresh poultry litter and compost, we found that the saturated hydraulic conductivity increased and the bulk density decreased, while the pH was generally not affected. Using poultry litter and compost as an alternative commercial fertilizers could be adapted by the farming community to protect the sustainability of our environment. Unwanted waste is used productively and soil is enriched for farming.

Carr, Stacy↗
NASA NTRS2009

NASA Engineering and Safety Center Technical Bulletin No. 09-05: Self-Contained Oxygen Generator: Effects of Organic Contamination, Briquette Fracturing, Pressure Containment, and Variations in Chemical Composition

A Self-Contained Oxygen Generator (SCOG) produces breathable oxygen (O 2 ) by using chemically-reactive briquettes that begin producing O 2 when mechanically ignited. Contamination with organic material of, or manufacturing defects in, the briquettes have been shown to lead to conditions that can cause an explosive failure

Self Contained Oxygen Generator↗
NASA NTRS2018

Hypersonic Chemically Reacting Boundary-Layer Stability using LASTRAC

Hypersonic boundary layer transition is critical to the design of all hypersonic vehicles due to its effect on the heat transfer into the vehicle surface and potential drag enhancement or reduction during reentry. Boundary layer transition and boundary layer stability analysis under hypersonic conditions has been studied for decades, yet there is ample room for improved accuracy and further investigations into the relevant phenomena. In this work, we present a recent implementation of chemical equilibrium, finite-rate chemistry, and thermochemical nonequilibrium capabilities into LASTRAC, an existing well-established boundary-layer stability analysis code. Verification against existing numerical results in the literature are presented. LASTRAC was previously able to address calorically perfect flows. By using solutions of the Parabolized Stability Equations (PSE) with chemical and thermal nonequilibrium, we are able to investigate the effects of chemical and thermal nonequilibrium on a variety of phenomena including stationary crossflow instability on a swept wing and 2nd mode instabilities over a wedge.

Kline, H. L.↗