Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flow visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1960

Effects of Sweep Angle on the Boundary-Layer Stability Characteristics of an Untapered Wing at Low Speeds

An investigation was conducted in the Ames 12-Foot Low-Turbulence Pressure Tunnel to determine the effects of sweep on the boundary-layer stability characteristics of an untapered variable-sweep wing having an NACA 64(2)A015 section normal to the leading edge. Pressure distribution and transition were measured on the wing at low speeds at sweep angles of 0, 10, 20, 30, 40, and 50 deg. and at angles of attack from -3 to 3 deg. The investigation also included flow-visualization studies on the surface at sweep angles from 0 to 50 deg. and total pressure surveys in the boundary layer at a sweep angle of 30 deg. for angles of attack from -12 to 0 deg. It was found that sweep caused premature transition on the wing under certain conditions. This effect resulted from the formation of vortices in the boundary layer when a critical combination of sweep angle, pressure gradient, and stream Reynolds number was attained. A useful parameter in indicating the combined effect of these flow variables on vortex formation and on beginning transition is the crossflow Reynolds number. The critical values of crossflow Reynolds number for vortex formation found in this investigation range from about 135 to 190 and are in good agreement with those reported in previous investigations. The values of crossflow Reynolds number for beginning transitions were found to be between 190 and 260. For each condition (i.e., development of vortices and initiation of transition at a given location) the lower values in the specified ranges were obtained with a light coating of flow-visualization material on the surface. A method is presented for the rapid computation of crossflow Reynolds number on any swept surface for which the pressure distribution is known. From calculations based on this method, it was found that the maximum values of crossflow Reynolds number are attained under conditions of a strong pressure gradient and at a sweep angle of about 50 deg. Due to the primary dependence on pressure gradient, effects of sweep in causing premature transition are generally first encountered on the lower surfaces of wings operating at positive angles of attack.

Boltz, Frederick W.↗
NASA NTRS1985

Seeding techniques used in the Vortex Research Facility

For many years, the Vortex Research Facility used kerosene vapor as seeding particles. The kerosene vapor formed (approx. 1 micron) particles initially. After injection into the test section, the vapor would begin to condense and form larger particles. By switching to solid particles, this has been eliminated. The uniform-sized (approx. 1 micron) solid particle seeding is used both to seed the Laser Velocimeter system and for flow visualization. After injection, the solid particles reach a uniform suspension before the vehicle is launched. It is found that the kerosene vapor poses a problem because it is a heated gas which modified the test section temperature distribution. It also produces high turbulence and secondary air currents because it was continually injected from the time of vehicle launch until model passage. In cases where the effects of either turbulence or the vertical temperature distribution are of interest, this hot gas injection method is unsuitable. Both types of seeding particles provide adequate flow visualization but are sensitive to vertical temperature distributions.

Satran, D. R.↗
NASA NTRSDate not supplied

Summary of the NASA Semi-Span High-Lift Common Research Model Wind Tunnel Test at the QinetiQ 5-Metre Low-Speed Facility

A summary and selected results from experimental testing of the NASA 10% scale semi-span High-Lift Common Research Model (CRM-HL) at the QinetiQ 5m (5mWT) pressurized low-speed wind tunnel are presented. There were many objectives of this test, the primary being to define a set of reference configurations for dissemination and use within the CRM-HL ecosystem, one in the landing configuration and one in the takeoff configuration. A database of force, moment, pressure and surface flow visualization data was collected to support several objectives: aerodynamic sensitivity to high-lift device positioning, Reynolds number effects on configuration selection, isolation of the effects of various components of the reference configuration e.g. landing gear, nacelle, horizontal tail, etc., and limited repeatability data for uncertainty quantification assessment. Some results were compared to limited data collected at the NASA Langley Research Center 14x22 wind tunnel to assess half-model effects and facility differences. Half-model effects were further studied with use of floor blowing to change boundary layer profile and assess effects on model aerodynamics. Flow visualization data were gathered with fluorescent mini-tufts and UV oil. Finally, test time was spend working on the development of new Particle Image Velocimetry (PIV) and Model Deformation Measurement (MDM) capabilities at the 5mWT facility.

Ashley Evans↗
NASA NTRS1994

2-D and 3-D oscillating wing aerodynamics for a range of angles of attack including stall

A comprehensive experimental investigation of the pressure distribution over a semispan wing undergoing pitching motions representative of a helicopter rotor blade was conducted. Testing the wing in the nonrotating condition isolates the three-dimensional (3-D) blade aerodynamic and dynamic stall characteristics from the complications of the rotor blade environment. The test has generated a very complete, detailed, and accurate body of data. These data include static and dynamic pressure distributions, surface flow visualizations, two-dimensional (2-D) airfoil data from the same model and installation, and important supporting blockage and wall pressure distributions. This body of data is sufficiently comprehensive and accurate that it can be used for the validation of rotor blade aerodynamic models over a broad range of the important parameters including 3-D dynamic stall. This data report presents all the cycle-averaged lift, drag, and pitching moment coefficient data versus angle of attack obtained from the instantaneous pressure data for the 3-D wing and the 2-D airfoil. Also presented are examples of the following: cycle-to-cycle variations occurring for incipient or lightly stalled conditions; 3-D surface flow visualizations; supporting blockage and wall pressure distributions; and underlying detailed pressure results.

Piziali, R. A.↗
NASA NTRS2017

Application of Background Oriented Schlieren for Altitude Testing of Rocket Engines

A series of experiments was performed to determine the feasibility of using the Background Oriented Schlieren, BOS, flow visualization technique to image a simulated, small, rocket engine, plume under altitude test conditions. Testing was performed at the NASA Glenn Research Centers Altitude Combustion Stand, ACS, using nitrogen as the exhaust gas simulant. Due to limited optical access to the facility test capsule, all of the hardware required to conduct the BOS were located inside the vacuum chamber. During the test series 26 runs were performed using two different nozzle configurations with pressures in the test capsule around 0.3 psia. No problems were encountered during the test series resulting from the optical hardware being located in the test capsule and acceptable resolution images were captured. The test campaign demonstrated the ability of using the BOS technique for small, rocket engine, plume flow visualization during altitude testing.

Background Oriented Schlieren↗
NASA NTRS1999

Fundamental Study of Material Flow in Friction Stir Welds

The presented research project consists of two major parts. First, the material flow in solid-state, friction stir, butt-welds as been investigated using a marker insert technique. Changes in material flow due to welding parameter as well as tool geometry variations have been examined for different materials. The method provides a semi-quantitative, three-dimensional view of the material transport in the welded zone. Second, a FSW process model has been developed. The fully coupled model is based on fluid mechanics; the solid-state material transport during welding is treated as a laminar, viscous flow of a non-Newtonian fluid past a rotating circular cylinder. The heat necessary for the material softening is generated by deformation of the material. As a first step, a two-dimensional model, which contains only the pin of the FSW tool, has been created to test the suitability of the modeling approach and to perform parametric studies of the boundary conditions. The material flow visualization experiments agree very well with the predicted flow field. Accordingly, material within the pin diameter is transported only in the rotation direction around the pin. Due to the simplifying assumptions inherent in the 2-D model, other experimental data such as forces on the pin, torque, and weld energy cannot be directly used for validation. However, the 2-D model predicts the same trends as shown in the experiments. The model also predicts a deviation from the "normal" material flow at certain combinations of welding parameters, suggesting a possible mechanism for the occurrence of some typical FSW defects. The next step has been the development of a three-dimensional process model. The simplified FSW tool has been designed as a flat shoulder rotating on the top of the workpiece and a rotating, cylindrical pin, which extends throughout the total height of the flow domain. The thermal boundary conditions at the tool and at the contact area to the backing plate have been varied to fit experimental data such as temperature profiles, torque and tool forces. General aspects of the experimentally visualized material flow pattern are confirmed by the 3-D model.

Reynolds, Anthony P.↗
NASA NTRS1994

Development of a multicomponent force and moment balance for water tunnel applications, volume 2

The principal objective of this research effort was to develop a multicomponent strain gauge balance to measure forces and moments on models tested in flow visualization water tunnels. Static experiments (which are discussed in Volume 1 of this report) were conducted, and the results showed good agreement with wind tunnel data on similar configurations. Dynamic experiments, which are the main topic of this Volume, were also performed using the balance. Delta wing models and two F/A-18 models were utilized in a variety of dynamic tests. This investigation showed that, as expected, the values of the inertial tares are very small due to the low rotating rates required in a low-speed water tunnel and can, therefore, be ignored. Oscillations in pitch, yaw and roll showed hysteresis loops that compared favorably to data from dynamic wind tunnel experiments. Pitch-up and hold maneuvers revealed the long persistence, or time-lags, of some of the force components in response to the motion. Rotary-balance experiments were also successfully performed. The good results obtained in these dynamic experiments bring a whole new dimension to water tunnel testing and emphasize the importance of having the capability to perform simultaneous flow visualization and force/moment measurements during dynamic situations.

Suarez, Carlos J.↗
DOE OSTI2026

Background-Oriented Schlieren Velocimetry of Helium Coolant Flow in Additively Manufactured Channels

High-pressure helium gas cooling is an attractive solution for thermal management of the fusion blanket first wall, as this coolant is chemically and neutronically inert and separable from hydrogenic species. However, due to the low thermal mass of helium, geometric optimization of these channels is required to provide sufficient cooling at manageable flow rates and pumping burdens. Increasingly, analysis and optimization of these coolant channels rely on computational fluid dynamics (CFD) simulations, and these require relevant experimental data for turbulence model validation. Toward this end, a high-pressure helium gas flow visualization system has been employed to image the flow of helium in flow channels with one-sided heating, mimicking the blanket first wall environment. Flow of helium at 4 MPa pressure and flow rates up to 68 g/s (Reynolds number 57 000) is supplied to rectangular channel test sections, with uniform heating applied to the bottom wall of the channel at heat fluxes varied between roughly 50 and 130 kW/m2. A high-speed camera is used to image index of refraction (IOR) gradients in the fluid via background-oriented schlieren (BOS), and temperature and pressure instrumentation are used to characterize thermal-hydraulic performance of each channel. Cross correlation of time-resolved BOS images is then used to calculate time-averaged 2-D helium velocity fields. Flow in additively manufactured (AM) channels is examined in this manner, including both featureless channels and those containing baffling as a heat transfer enhancement. The flow distribution seen in the featureless case differs significantly from that seen in prior simulations, whereas the flow in the baffled case shows the predicted behavior of flow forced along the heated wall. This augmented flow distribution is seen to increase the heat transfer coefficient in the baffled test section. Here, strategies are discussed for ongoing and future validation of these simulations, with the aim of model deployment for blanket cooling design and optimization.

Additive manufacturing↗
NASA NTRS1964

Oil-smeared models aid wind tunnel measurements

For visualizing flow characteristics in wind tunnel tests, model surfaces are smeared with any common petroleum-base oils. These fluoresce under ultraviolet light and the flow patterns are readily visualized.

Katzoff, S.↗
NASA NTRS1980

Investigations of eddy coherence in jet flows

In turbulent shear flow the term coherent structures refers to eddies which are both spatially coherent, i.e., large eddies, aand also temporally coherent, i.e., they retain their identities for times which are long compared with their time scales in fixed point measurements. In transitional flows, the existence of such structures is evident from flow visualizations. In many other flows, such structures are not so evident. The reasons for the existence of these two classes of flows are discussed and attention is focused upon the more difficult flows, where coherent structures are not so evident. Techniques by which the existence (or nonexistence) of such structures in these flows can be established from point measurements, are also discussed. A major problem is shown to be the need to discriminate between real losses in eddy coherence and apparent losses in coherence introduced by phase scrambling effects which 'smear' multipoint correlations. The analysis of multiprobe time dependent data in cold and reacting round turbulent jets is described and it is shown how evidence of strong eddy coherence can be extracted from data.

Yule, A. J.↗
NASA NTRS1986

Visualization of flows in a motored rotary combustion engine using holographic interferometry

The use of holographic interferometry to view the small- and large-scale flow field structures in the combustion chamber of a motored Wankel engine assembly is described. In order that the flow patterns of interest could be observed, small quantities of helium were injected with the intake air. Variation of the air flow patterns with engine speed, helium flow rate, and rotor position are described. The air flow at two locations within the combustion chamber was examined using this technique.

Hicks, Y. R.↗
NASA NTRS1986

Visualization and flow surveys of the leading edge vortex structure on delta wing planforms

In the present experimental investigation of thin delta wing vortex breakdown, for the cases of sweep angles of 70, 75, 80, and 85 deg, and smoke flow visualization/laser light sheet technique is used to obtain cross sectional views of the leading edge vortices as they break down. A combination of lateral and longitudinal cross sectional views furnishes data on the three-dimensional character of the vortex before, during, and after breakdown. Velocity measurements conducted with a laser Doppler anemometer on the 70 deg sweep delta, at 30 deg angle-of-attack, indicate that when breakdown occurs the core flow is transformed from a jet-like to a wake-like flow.

Payne, F. M.↗
NASA NTRS1986

Visualization of flows in a motored rotary combustion engine using holographic interferometry

The use of holographic interferometry to view the small- and large-scale flow field structures in the combustion chamber of a motored Wankel engine assembly is described. In order that the flow patterns of interest could be observed, small quantities of helium were injected with the intake air. Variation of the air flow patterns with engine speed, helium flow rate, and rotor position are described. The air flow at two locations within the combustion chamber was examined using this technique.

Hicks, Yolanda R.↗
NASA NTRS1984

Experimental results for a two-dimensional supersonic inlet used as a thrust deflecting nozzle

Nearly all supersonic V/STOL aircraft concepts are dependent on the thrust deflecting capability of a nozzle. In one unique concept, referred to as the reverse flow dual fan, not only is there a thrust deflecting nozzle for the fan and core engine exit flow, but because of the way the propulsion system operates during vertical takeoff and landing, the supersonic inlet is also used as a thrust deflecting nozzle. This paper presents results of an experimental study to evaluate the performance of a supersonic inlet used as a thrust deflecting nozzle for this reverse flow dual fan concept. Results are presented in terms of nozzle thrust coefficient and thrust vector angle for a number of inlet/nozzle configurations. Flow visualization and nozzle exit flow survey results are also shown.

Johns, Albert L.↗
NASA NTRS1990

Flow measurements in a model of the mildly curved femoral artery of man

The effects of curvature on the flow rate near the wall in the vicinity of the mildly curved femoral artery of man, and on the pressure distributions along the curved segment, were investigated using glass and tygon flow models constructed to conform to the shape of the femoral angiogram of a human subject. The test fluid was 33 percent aqueous sucrose. Steady flow observations, made using a dye flow visualization system, revealed a flow pattern like that observed in coiled pipes. A double helical type flow was found to develop, with converging streamlines in the wall vicinity from the upper and lower plane of curvature merging asymptotically along the inner curvature in a stable manner. Pressure measurements for steady flow revealed progressively larger pressure drops with distance along the entrance region of the curved segment, relative to that for a straight lumen.

Back, L. H.↗
NASA NTRS1989

Simulation of powered-lift flows

The primary objective is to expose government, industry, and academic scientists to work underway at NASA-Ames towards the application of CFD to the powered lift area. One goal is to produce the technologies which will be required in the application of numerical techniques to, for example, the Supersonic STOVL program. The progress to date on the following specific projects is presented: Jet in ground effect with crossflow; Jet in a crossflow; Delta planform with multiple jets in ground effect; Integration of CFD with thermal and acoustic analyses; Improved flow visualization techniques for unsteady flows; YAV-8B Harrier simulation program; and E-7 simulation program.

Vandalsem, William R.↗
NASA NTRS1954

Secondary Flows and Boundary-Layer Accumulations in Turbine Nozzles

An investigation of secondary-flow loss patterns originating in three sets of turbine nozzle blade passages was conducted by means of flow-visualization studies and detailed flow measurements. For all cases, high loss values were measured in the fluid downstream of the corners formed by the suction surfaces of the blades and the shrouds, and these losses were accompanied by discharge-angle deviations from design values. Despite the size of the loss regions and angle gradients, over-all mass-average blade efficiencies were of the order of 0.99 and 0.98 and, therefore, are not a good index of blade performance.

Rohlik, Harold E↗