Search NASA⌕ Search

SEARCH · Search NASA

Results for “Free Flight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Positronium Laser Cooling via the 1 3 S − 2 3 P Transition with a Broadband Laser Pulse

We report on laser cooling of a large fraction of positronium (Ps) in free flight by strongly saturating the 1 3 S − 2 3 P transition with a broadband, long-pulsed 243 nm alexandrite laser. The ground state Ps cloud is produced in a magnetic and electric field-free environment. We observe two different laser-induced effects. The first effect is an increase in the number of atoms in the ground state after the time Ps has spent in the long-lived 2 3 P states. The second effect is one-dimensional Doppler cooling of Ps, reducing the cloud’s temperature from 380(20) to 170(20) K. We demonstrate a 58(9)% increase in the fraction of Ps atoms with v 1 D < 3.7 × 10 4 m s − 1 . Published by the American Physical Society 2024

Glöggler, L. T. (ORCID:0000000301948680)↗
NASA NTRS2011

The LISA Pathfinder Mission

LISA Pathfinder is a dedicated technology demonstration space mission for the Laser Interferometer Space Antenna (LISA), a NASA/ESA collaboration to operate a space-based observatory for gravitational waves in the milli-Hertz band. Although the formal partnership between the agencies was dissolved in the Spring of 2011, both agencies are actively pursuing concepts for LISA-like gravitational wave observatories. These concepts take advantage of the significant technology development efforts that have already been made, especially those of the LISA Pathfinder mission. LISA Pathfinder, which is in the late stages of implementation, will place two test masses in drag-free flight and measure the relative acceleration between them. This measurement will validate a number of technologies that are critical to LISA-like gravitational wave instruments including sensing and control of the test masses, drag-free control laws, microNewton thrusters, and picometer-level laser metrology. We will present the current status of the LISA Pathfinder mission and associated activities.

Thorpe, james↗
NASA NTRS1991

AFE base flow computations

Hypersonic wake flows behind the Aeroassist Flight Experiment (AFE) geometry are analyzed using two Navier-Stokes flow solvers. Many of the AFE wake features observed in ballistic-range shadowgraphs are simulated using a simple, two-dimensional semicylinder geometry at moderate angles of attack. At free-stream conditions corresponding to a Hypersonic Free Flight Facility (HFFF) AFE experiment, the three-dimensional base flow for the AFE geometry is computed using an ideal-gas, Navier-Stokes solver. The computed results agree reasonably well with the shadowgraphs taken at the HFFF. An ideal-gas and a nonequilibrium Navier-Stokes solver have been coupled and applied to the complete flow around the AFE vehicle at the free-stream conditions corresponding to a nomial trajectory point. Limitations of the coupled ideal-gas and nonequilibrium solution are discussed. The nonequilibrium base flow solution is analyzed for the wake radiation and the radiation profiles along various lines of sight are compared. Finally, the wake unsteadiness is predicted using experimental correlations and the numerical solutions. An adaptive grid code, SAGE, has been used in all the simulations to enhance the solution accuracy. The grid adaptation is found to be necessary in obtaining base flow solutions with accurate flow features.

Venkatapathy, Ethiraj↗
NASA NTRSDate not supplied

Overview of the Subscale RAVEN Flight Controls and Modeling Testbed

The Research Aircraft for eVTOL Enabling TechNologies (RAVEN) Subscale Wind-Tunnel and Flight Test (SWFT) model is a subscale aircraft built for flight dynamics and controls research demonstrated in wind-tunnel and flight-test experiments. The intent of this paper is to provide a summary of past, current, and future efforts being pursued by the RAVEN-SWFT project. Initially, vehicle development guidelines were crafted by a multidisciplinary team to ensure that the RAVEN-SWFT vehicle was well suited for research in multiple areas, including aero-propulsive modeling, flight controls, and autonomy, among others. The vehicle has been used to obtain extensive wind-tunnel data, enabling aero-propulsive model development across the transition flight envelope and validation of computational tools. The vehicle will be used to conduct flight testing in order to evaluate modeling strategies and flight control logic. The RAVEN-SWFT model also serves as a risk reduction activity for a conceptual, full-scale vehicle in the 1000-lb class. The next steps in the project are to successfully demonstrate free flight in hover, transition, forward flight, and the reverse thereof, utilizing custom control laws integrated onto the RAVEN-SWFT avionics hardware. The project intends to publicize all of the geometry, data, and methods in future reports.

eVTOL↗
NASA NTRS2000

Rotorcraft Noise Abatement Flight Path Modeling

This report addresses development of a rotor state/trim modeling capability for noise modeling of decelerating rotorcraft approaches. The resulting technique employs discretization of the descent trajectory as multiple steady state segments for input to CAMRAD.Mod 1 to predict rotor states for acoustic analysis. Deceleration is included by modifying the CAMRAD.Mod 1 free flight trim options to allow trim to the specified acceleration/deceleration components.

Murty, Hema↗
NASA NTRS1996

STS-77 Flight Day 2

On this second day of the STS-77 mission, the flight crew, Cmdr. John H. Casper, Pilot Curtis L. Brown, Jr., and Mission Specialists Andrew S.W. Thomas, Ph.D., Daniel W. Bursch, Mario Runco, Jr., and Marc Garneau, Ph.D., are seen deploying the Spartan satellite for its 24 hour free flight away from Endeavor to test new inflatable antenna technology. The inflation procedure begins as the shuttle and antenna pass over New Mexico, Southern California, the Grand Canyon, Appalachian Mountains, and coast of Virginia. The inflation takes about 5 minutes, bringing the antenna to its full size of 90 feet by 50 feet. After an hour and a half, the antenna was to be jettisoned from the Spartan.

Source record↗
NASA NTRS2004

Fact Sheets of CTAS and NASA Decision-Support Tools and Concepts

Distributed Air/Ground (DAG) Traffic Management (TM) is an integrated operational concept in which flight deck crews, air traffic service providers and aeronautical operational control personnel use distributed decision-making to enable user preferences and increase system capacity, while meeting air traffic management (ATM) requirements. It is a possible operational mode under the Free Flight concept outlined by the RTCA Task Force 3. The goal of DAG-TM is to enhance user flexibility/efficiency and increase system capacity, without adversely affecting system safety or restricting user accessibility to the National Airspace System (NAS). DAG-TM will be accomplished with a human-centered operational paradigm enabled by procedural and technological innovations. These innovations include automation aids, information sharing and Communication, Navigation, and Surveillance (CNS) / ATM technologies. The DAG-TM concept is intended to eliminate static restrictions to the maximum extent possible. In this paradigm, users may plan and operate according to their preferences - as the rule rather than the exception - with deviations occumng eyond the year 2015. Out of a total of 15 concept elements, 4 have been selected for initial sutidies (see Key Elements in sidebar). DAG-TM research is being performed at Ames, Glenn, and Langley Research Centers.

Lee, Katharine↗
NASA NTRS1958

Flight Investigation of a Normal-Acceleration Automatic Longitudinal Control System in a Fighter Airplane

A flight investigation was made to obtain experimental information on the handling qualities of a normal-acceleration type of automatic longitudinal control system. The control system was installed in a subsonic fighter-type airplane. In hands-off (stick-free) flight the normal-acceleration control system attempted to regulate the normal acceleration to a constant value which is dependent on the automatic-control-system trim setting. In maneuvering flight a given pilot's stick deflection produced a proportional change in normal acceleration, the change in acceleration being independent of flight condition. A small side-located controller stick was used by the pilot to introduce signals into the automatic control system. In the flight program emphasis was placed on the acceleration-limiting capabilities of the control system. The handling qualities were investigated in maneuvers such as slow and rapid pull-ups and turns and also in flight operations such as cruising, stalls, landings, aerobatics, and air-to-air tracking. Good acceleration limiting was obtained with the normal-acceleration control system by limiting the magnitude of the input signal that the pilot could introduce into the control system. The same values of control-system gain settings could be used from an acceleration-limiting stand-point at both 10,000 and 30,000 feet for the complete speed range of the airplane. The response characteristics of the airplane-control system combination were also satisfactory at both high and low altitude with these same values of control-system gain setting. In the pilot's opinion, the normal-acceleration control system provided good stability and control characteristics in flight operations such as cruising, stalls, landings, aerobatics, and air-to-air tracking.

Sjoberg, S. A.↗
NASA NTRS2004

DAG-TM Concept Element 11 CNS Performance Assessment: ADS-B Performance in the TRACON

Distributed Air/Ground (DAG) Traffic Management (TM) is an integrated operational concept in which flight deck crews, air traffic service providers and aeronautical operational control personnel use distributed decision-making to enable user preferences and increase system capacity, while meeting air traffic management (ATM) safety requirements. It is a possible operational mode under the Free Flight concept outlined by the RTCA Task Force 3. The goal of DAG-TM is to enhance user flexibility/efficiency and increase system capacity, without adversely affecting system safety or restricting user accessibility to the National Airspace System (NAS). DAG-TM will be accomplished with a human-centered operational paradigm enabled by procedural and technological innovations. These innovations include automation aids, information sharing and Communication, Navigation, and Surveillance (CNS) / ATM technologies. The DAG-TM concept is intended to eliminate static restrictions to the maximum extent possible. In this paradigm, users may plan and operate according to their preferences - as the rule rather than the exception - with deviations occurring only as necessary. The DAG-TM concept elements aim to mitigate the extent and impact of dynamic NAS constraints, while maximizing the flexibility of airspace operations

Raghavan, Rajesh S.↗
NASA NTRS2019

Subsonic Dynamic Testing of a Subscale ADEPT Entry Vehicle

The Adaptive Deployable Entry and Placement Technology (ADEPT) is a mechanically-deployed entry system. A sounding rocket test flight of an ADEPT vehicle, known as ADEPT SR-1, was conducted in September 2018. Prior to this sounding rocket test, an investigation was performed using the NASA Langley Research Center 20-ft Vertical Spin Tunnel (VST) to assess the free-flight dynamic characteristics of ADEPT SR-1 at subsonic speeds. The model of ADEPT SR-1 for this VST test was fabricated at 50-percent geometric scale, with dynamically scaled mass properties (Froude scaled) to represent full-scale flight at an altitude of 1.2 km above sea level. The subsonic dynamic characteristics of ADEPT SR-1 were of interest prior to the sounding rocket test because of payload recovery considerations. At low roll rates the model was found to have acceptable dynamic characteristics. It was statically stable in pitch and yaw, exhibiting limit cycle pitch/yaw oscillations of no greater than 20 degrees (the angle between the model’s longitudinal axis and nadir). The model was able to recover from large upsets in pitch and yaw, although if sufficiently provoked it tumbled. Damping in roll was low. At high roll rates the pitch and yaw oscillations grew in magnitude and rate. This behavior was also observed during the sounding rocket flight test.

Cruz, Juan R.↗
NASA NTRS1959

Flight Investigation of the Stability and Control Characteristics of a 1/4-Scale Model of a Tilt-Wing Vertical-Take-Off-and-Landing Aircraft

An experimental investigation has been conducted to determine the dynamic stability and control characteristics of a tilt-wing vertical-take-off-and-landing aircraft with the use of a remotely controlled 1/4-scale free-flight model. The model had two propellers with hinged (flapping) blades mounted on the wing which could be tilted up to an incidence angle of nearly 90 deg for vertical take-off and landing. The investigation consisted of hovering flights in still air, vertical take-offs and landings, and slow constant-altitude transitions from hovering to forward flight. The stability and control characteristics of the model were generally satisfactory except for the following characteristics. In hovering flight, the model had an unstable pitching oscillation of relatively long period which the pilots were able to control without artificial stabilization but which could not be considered entirely satisfactory. At very low speeds and angles of wing incidence on the order of 70 deg, the model experienced large nose-up pitching moments which severely limited the allowable center-of-gravity range.

Tosti, Louis P.↗
NASA NTRS1988

A linearized model of helicopter dynamics including correlation with flight test

A linearized model for rotorcraft dynamics has been developed through the use of symbolic automatic equation generation techniques. The dynamic model has been formulated in a unique way such that it can be used to analyze a variety of rotor/body coupling problems including a rotor mounted on a flexible shaft with a number of modes as well as free flight stability and control characteristics. Direct comparison of the time response to longitudinaol, lateral and directional control inputs at various trim conditions shows that the linear model yields good to very good correlation with flight test. In particular it is also shown that a dynamic inflow model is essential to obtain good time response correlation especially for the hover trim condition and also that at translational flight trim conditions the main rotor wake interaction with the tail rotor and fixed tail surfaces is a significant contributor to the response. A relatively simple model for the downwash and sidewash at tail surfaces based on flat vortex wake theory is shown to produce good agreement. Finaly, the influence of rotor flap and lag dynamics on automatic control systems feedback gain limitations is investigated with the model.

Curtiss, H. C.↗
NASA NTRS1956

Flight Determination of Drag of Normal-Shock Nose Inlets with Various Cowling Profiles at Mach Numbers from 0.9 to 1.5

External-drag data are presented for normal-shock nose inlets with NACA 1-series, parabolic, and conic cowling profiles. The tests were made at an angle of attack of 0 degrees by using rocket-propelled models in free flight at Mach numbers from 0.9 to 1.5. The Reynolds number based on body maximum diameter varied from 2.5 x 10 sup 6 to 5.5 x 10 sup 6. At maximum flow rate, the inlet models had about the same external drag at a Mach number of approximately 1.1, but at higher Mach numbers the sharp-lip conic cowling had the least drag. Blunting or beveling the lip of the conic cowling while keeping the fineness ratio constant resulted in drag coefficients slightly higher than for the sharp-lip conic cowling at maximum flow rate. At a mass-flow ratio of about 0.8, the conic cowlings with sharp, blunt, or beveled lips and the parabolic cowling all gave about the same drag. The higher drag of the NACA 1-49-300 cowling, compared with the blunt-lip conic cowling, is associated with the greater fullness back of the inlet.

Sears, R I↗
NASA NTRS1949

Flight Investigation of 6.25-Inch-Diameter Deacon Rocket and 10-Inch-Scale Model Rocket

Flight tests were conducted at the NACA Pilotless Aircraft Research Station, Wallops Island, to determine the characteristics of the Allegany Ballistics Laboratory's 6.2inch-diameter Deacon and lO-inch-scale model solid-propellant rocket motors. The tests were performed to assist in the development of these rockets which were designed for, and urgently needed to propel supersonic research models and pilotless aircraft. The tests showed that the rocket motors functioned properly under various flight- acceleration loads over a range of pre-ignition grain temperatures. A maximum velocity of 4180 feet per second was obtained at an elapsed time of 2.9 seconds with the 6.25-inch Deacon rocket motor at a gross weight of l9O pounds. Free-flight data of drag coefficient for the Deacon configuration for a Mach number range of 1.1 to 3.6 have been obtained from flight tests of several pounds. Camera studies of the take-off and flights of the Deacon rocket shared no evidence of breakup of propellant grains. An analysis of the forces to which the Deacon rocket grain is subjected was made. The analysis shows that the grain loading is most severe near the beginning and near the end of the rocket action time. The 10-inch-scale model rocket motor is a scaled model of the l6-inch- diameter multi-perforated, cast-grain rocket motor. A maximum velocity of 1625 feet per second at a time of 1.075 seconds was obtained at a gross weight of 309 pounds.

Watson, R. S.↗
NASA NTRS2011

Managing Toxicological Risks: The Legacy of Shuttle Operations

Space toxicology greatly matured as a result of research and operations associated with the Shuttle. Materials offgassing had been a manageable concern since the Apollo days, but we learned to pay careful attention to compounds that could escape containment, to combustion events, to toxic propellants, to overuse of utility compounds, and to microbial and human metabolites. We also learned that flying real-time hardware to monitor air pollutants was a pathway with unanticipated speed bumps. Each new orbiter was tested for any excess offgassing products that could pollute the air during flight. In the late 1990s toxicologists and safety experts developed a 5-level toxicity rating system to guide containment of toxic compounds. This system is now in use aboard the International Space Station (ISS). Several combustion events during Shuttle Mir and also during Shuttle free-flight impelled toxicologists to identify hardware capable of monitoring toxic products; however, rapid adaptation of the hardware for the unique conditions of spaceflight caused unexpected missteps. Current and planned combustion analyzers would be useful to commercial partners that wish to manage the risk of health effects from thermal events. Propellants received special attention during the Shuttle program because of the possibility of bringing them into the habitable volume on extravehicular activity suits. Monitors for the airlocks were developed to mitigate this risk. Utility materials, such as lubricants, posed limited toxicological problems because water was not recovered. One clearly documented case of microbial metabolites polluting the Shuttle atmosphere was noted, and this has implications for commercial flights and control of microbes. Finally, carbon dioxide, the major human metabolite, episodically presented air quality problems aboard Shuttle, especially when nominal air flows were obstructed. Commercial vehicles must maintain robust air circulation given the anticipated high density of human occupants.

James, John T.↗
NASA NTRS1976

Flight characteristics of probes in the atmospheres of Mars, Venus, and the outer planets

Density, pressure, and temperature profiles of an unknown planetary atmosphere can be obtained from the high-speed entry of a probe provided the aerodynamic characteristics of the probe in this atmosphere are accurately known. An investigation of the effect of gas composition on probe aerodynamics has been conducted in the Ames Hypersonic Free Flight Facility by gun launching small-scale models into atmospheres representative of Mars, Venus, Jupiter, and Saturn. Aerodynamic data at conditions matching the velocity and Reynolds number at a number of points on the Viking trajectory (Mars) were obtained in both air and carbon dioxide and significant differences were noted. Aerodynamic data are also presented from tests in hydrogen and hydrogen-helium mixtures, gases which characterize the atmospheres of the outer planets.

Intrieri, P. F.↗
NASA NTRS1954

The zero-lift drag of a slender body of revolution (NACA RM-10 research model) as determined from tests in several wind tunnels and in flight at supersonic speeds

The results of tests of a slender body of revolution designated the NACA rm-10 have been compiled from various NACA test facilities. Zero-lift drag data are presented for a Reynolds number range from about 1 x 10(6) to 40 x 10(6) from several wind tunnels and from about 12 x 10(6) to 140 x 10(6) from free-flight tests. The Mach numbers covered include 1.5 to 2.4 for the wind-tunnel data and 0.85 to 2.5 for the flight results. The wind tunnel models were tested with and without 60 degree sweptback stabilizing fins and the flight models were tested with stabilizing fins. Comparison of the data obtained in the several wind tunnels for the body alone (without fins) shows good agreement between the different facilities. There are unexplained differences however between the wind-tunnel results with fins attached and flight results, as well as differences between full-scale and half-scale flight models, which cannot be explained as an effect of Reynolds number.

Evans, Albert J↗
NASA NTRS1982

Dynamic stability of a buoyant quad-rotor aircraft

Stability characteristics of a buoyant quad-rotor aircraft (BQRA) in hover and forward flight are examined by considering linear, state-variable, and nonlinear flight simulation models of such a configuration. The effects of carrying a sling load on the vehicle dynamics is predicted by considering a coupled model of the two bodies. Inherent stability characteristics of the vehicle are analyzed and compared with those of a helicopter and an airship in free flight. Typical operational conditions that could lead to vehicle instability are described in the flight envelope of interest.

Nagabhushan, B. L.↗