Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel Cycle Simulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Avoiding compressor surge during emergency shutdown hybridturbine systems

A new emergency shutdown procedure for a direct-fired fuel cell turbine hybrid power system was evaluated using a hardware-based simulation of an integrated gasifier/fuel cell/turbine hybrid cycle (IGFC), implemented through the Hybrid Performance (Hyper) project at the National Energy Technology Laboratory, U.S. Department of Energy (NETL). The Hyper facility is designed to explore dynamic operation of hybrid systems and quantitatively characterize such transient behavior. It is possible to model, test, and evaluate the effects of different parameters on the design and operation of a gasifier/fuel cell/gas turbine hybrid system and provide a means of quantifying risk mitigation strategies. An open-loop system analysis regarding the dynamic effect of bleed air, cold air bypass, and load bank is presented in order to evaluate the combination of these three main actuators during emergency shutdown. In the previous Hybrid control system architecture, catastrophic compressor failures were observed when the fuel and load bank were cut off during emergency shutdown strategy. Improvements were achieved using a nonlinear fuel valve ramp down when the load bank was not operating. Experiments in load bank operation show compressor surge and stall after emergency shutdown activation. The difficulties in finding an optimal compressor and cathode mass flow for mitigation of surge and stall using these actuators are illustrated.

20 FOSSIL-FUELED POWER PLANTS↗

Ascent performance of an air-breathing horizontal-takeoff launch vehicle

Simulations are conducted to investigate a proposed NASA launch vehicle that is fully reusable, takes off horizontally, and uses airbreathing propulsion in a single stage. The propulsion model is based on a cycle analysis method, and the vehicle is assumed to be a rigid structure with distributed fuel, operating under a range of atmospheric conditions. The program to optimize simulated trajectories (POST) is modified to include a predictor-corrector guidance capability and then used to generate the trajectories. Significant errors are encountered during the unpowered coast phase due to uncertainty in the atmospheric density profile. The amount of ascent propellant needed is shown to be directly related to the thrust-vector angle and the location of the center of gravity of the vehicle because of the importance of aim-drag losses to total ideal velocity.

Powell, Richard W.↗

UMo Benchmark Experiment Data Needed to Support Computational and Nuclear Data Validation

Currently there are almost no benchmark experiment data available directly supporting neutronics modeling and simulation of ~20 wt.% 235U, UMo fuel contained within the Organisation for Co-operation and Development Nuclear Energy Agency (OECD NEA) international benchmark handbooks from the International Criticality Safety Benchmark Evaluation Project (ICSBEP) and International Reactor Physics Experiment Evaluation Project (IRPhEP). The benchmarks within these two handbooks represent the international standards used to support computational and nuclear data validation. Recent activities in nuclear data development supporting new neutronics thermal scattering cross sections for UMo fuel indicate the necessity to provide quality benchmark experiment data that can be utilized to support their validation and development. Preparation of high-integrity neutronics benchmarks from UMo experimental data will ensure proper integral testing of these cross sections, as well as serve to support computational validation of contemporary modeling and simulation software.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of Shear Strength Assumptions on BISON Debonding Simulations

Accurately predicting the thermomechanical response of buffer–IPyC debonding in TRISO fuel particles requires reliable mechanical property inputs for each coating layer, particularly the normal and shear strengths that influence interlayer delamination and stress concentrations. Micro tensile testing of AGR-2 fuel particles provided experimentally measured normal strengths for the buffer, IPyC, and buffer–IPyC interface; however, shear strength was not measured. As a result, BISON simulations of interface debonding must rely on assumed shear strength values, typically estimated as 20–40% of the measured ultimate tensile strength. This study evaluates how these assumed shear strength values influence cohesive zone model (CZM) predictions of buffer–IPyC separation in AGR 2 TRISO particles. Using micro tensile data from three AGR 2 compacts (2 1 3, 5 1 3, and 6 3 3), BISON simulations were performed with multiple shear strength assumptions to quantify their effect on radial and tangential stress evolution, debonding, and gap propagation. The results show that shear strength is a high sensitivity parameter: increasing the assumed shear strength significantly alters the stress distribution at the buffer–IPyC junction, shifts the predicted debonding location, and changes the extent of partial gap formation. While normal strength controls the initiation of interface separation, shear strength strongly influences the mode mixity of the failure process and the resulting stress concentrations transmitted to the IPyC and SiC layers. These findings highlight a critical gap in current TRISO mechanical characterization. Without experimentally measured shear strength, BISON simulations must rely on approximations that introduce uncertainty into predictions of coating layer integrity and fission product barrier performance. Future fuel qualification campaigns should therefore consider measurement of shear strength at the interlayer interfaces to reduce model uncertainty and improve the fidelity of TRISO fuel performance simulations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Quantify Water Extraction by TBP/Dodecane via Molecular Dynamics Simulations

The purpose of this project is to quantify the interfacial transport of water into the most prevalent nuclear reprocessing solvent extractant mixture, namely tri-butyl- phosphate (TBP) and dodecane, via massively parallel molecular dynamics simulations on the most powerful machines available for open research. Specifically, we will accomplish this objective by evolving the water/TBP/dodecane system up to 1 ms elapsed time, and validate the simulation results by direct comparison with experimentally measured water solubility in the organic phase. The significance of this effort is to demonstrate for the first time that the combination of emerging simulation tools and state-of-the-art supercomputers can provide quantitative information on par to experimental measurements for solvent extraction systems of relevance to the nuclear fuel cycle. Results: Initially, the isolated single component, and single phase systems were studied followed by the two-phase, multicomponent counterpart. Specifically, the systems we studied were: pure TBP; pure n-dodecane; TBP/n-dodecane mixture; and the complete extraction system: water-TBP/n-dodecane two phase system to gain deep insight into the water extraction process. We have completely achieved our goal of simulating the molecular extraction of water molecules into the TBP/n-dodecane mixture up to the saturation point, and obtained favorable comparison with experimental data. Many insights into fundamental molecular level processes and physics were obtained from the process. Most importantly, we found that the dipole moment of the extracting agent is crucially important in affecting the interface roughness and the extraction rate of water molecules into the organic phase. In addition, we have identified shortcomings in the existing OPLS-AA force field potential for long-chain alkanes. The significance of this force field is that it is supposed to be optimized for molecular liquid simulations. We found that it failed for dodecane and/or longer chains for this particular solvent extraction application. We have proposed a simple way to circumvent the artificial crystallization of the chains at ambient temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BISON fuel performance modeling optimization for experiment X447 and X447A using axial swelling and cladding strain measurements

With the recent need to qualify new reactor designs such as the Versatile Test Reactor (VTR), fuel performance calculations need to be performed to determine safety criteria of the proposed designs. In order to validate the fuel performance results obtained by a fuel performance code, BISON, for new reactor designs, legacy fuel from EBR-II and FFTF MFF with Post -Irradiation Examination (PIE) data need to be used as validation cases to benchmark models. Here in this work, BISON has been paired with the Fuels Irradiation & Physics Database (FIPD) and IFR Materials Information System (IMIS) to supply PIE data for comparison with simulations of EBR-II experiments X447/X447A. X447/X447A were assessed by implementing models for Fuel Cladding Chemical Interaction (FCCI) within BISON and optimizing the friction coefficient between the fuel surface and the cladding, the anisotropic swelling factor, and the HT9 first thermal creep scalar (which scales the first term in the HT9 creep equation) to best match the PIE axial fuel swelling height and cladding profilometry for all pins in X447/X447A. The optimal values were found using a generic algorithm developed to select different values for the three parameters until end criteria was met and error couldn’t be reduced further. The BISON-simulated cladding profilometry was evaluated using Standard Error of the Estimate (SEE) to account for the profile shape of the cladding profilometry. Optimal values for the friction coefficient, anisotropic fuel swelling factor, and HT9 first thermal creep scalar were found to best fit the BISON simulation results to the PIE measurements found in IMIS and FIPD. Improvements to current models are suggested to account for the underprediction of fuel swelling at low burnups and the overprediction of fuel swelling at higher burnups observed for the axial fuel swelling height. Although two pins in EBR-II X447/X447A (DP70 and DP75) were known to fail due to FCCI, none of the pins simulated in BISON reached a cumulative damage fraction (CDF) above 0.008 with FCCI correlations coupled in the BISON simulations. The error estimate generated for all pins in X447/X447A using optimal values was 209 µm, which is deemed acceptable.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of COBRA-TF Critical Heat Flux Models for Triangular Fuel Assembly Pitch

The Coolant Boiling in Rod Arrays-Two Fluid (COBRA-TF) code is a best estimate code which is used to perform thermal-hydraulic analyses of a light water reactor vessel. The COBRA-TF heat transfer package has models calculating the critical heat flux (CHF). In order to verify code's predictive capability for CHF for triangular nuclear fuel assembly pitch, experiment results and system parameters of KS-1 test facility that is single loop model of the VVER primary system located in Kurchatov Institute were simulated using COBRA-TF. In order to calculate CHF for triangular nuclear fuel assembly pitch there is a look-up table generated. In addition, there are some correction factors for critical heat flux values listed the table. In this study, once KS-1 experiment results were simulated using COBRA-TF, correction factors were used to correct CHF results from COBRA-TF calculations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Coupling Experiments and Simulations to Understand Metallic Fuel Behavior

The development of metal alloy fuels for minor actinide transmutation in fast reactor systems is of high importance. However, it faces numerous technical challenges such as: i) fuel behavior has to be benign during core off-normal events; ii) fuel has to maintain integrity to high burnup; iii) low minor actinide fabrication loss under remote handling conditions; and iv) fuel has to lend itself to low-loss recycling process. Limited experimental fuel performance data is currently available to support the selection of a fuel type for a transmutation system. Metallic fuels are being considered for application in fast reactor environment due to the high burn-up, high fissile and fertile density capability, inherent safety characteristics, favorable thermal response, and relatively easy recycling process. The uranium-plutonium-zirconium (U-Pu- Zr) based alloys are considered as one of the most promising metallic fuels for such application. In this work, we present results of microstructural characterization of Pu-Zr and U-Pu-Zr alloys and provide much needed linkage between thermal properties and microscopic scale observation. A firm understanding of microstructural evolution in reactor materials is imperative and will lead to deeper understanding of in-reactor degradation behavior, creating a new generation of radiation-resistant materials and fuels with the potential for significant increases in burn-up.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Use Of Computational Human Performance Modeling As Task Analysis Tool

During a review of the Advanced Test Reactor safety basis at the Idaho National Laboratory, human factors engineers identified ergonomic and human reliability risks involving the inadvertent exposure of a fuel element to the air during manual fuel movement and inspection in the canal. There were clear indications that these risks increased the probability of human error and possible severe physical outcomes to the operator. In response to this concern, a detailed study was conducted to determine the probability of the inadvertent exposure of a fuel element. Due to practical and safety constraints, the task network analysis technique was employed to study the work procedures at the canal. Discrete-event simulation software was used to model the entire procedure as well as the salient physical attributes of the task environment, such as distances walked, the effect of dropped tools, the effect of hazardous body postures, and physical exertion due to strenuous tool handling. The model also allowed analysis of the effect of cognitive processes such as visual perception demands, auditory information and verbal communication. The model made it possible to obtain reliable predictions of operator performance and workload estimates. It was also found that operator workload as well as the probability of human error in the fuel inspection and transfer task were influenced by the concurrent nature of certain phases of the task and the associated demand on cognitive and physical resources. More importantly, it was possible to determine with reasonable accuracy the stages as well as physical locations in the fuel handling task where operators would be most at risk of losing their balance and falling into the canal. The model also provided sufficient information for a human reliability analysis that indicated that the postulated fuel exposure accident was less than credible.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Atomic scale simulations for improved CRUD and fuel performance modeling

A more mechanistic description of fuel performance codes can be achieved by deriving models and parameters from atomistic scale simulations rather than fitting models empirically to experimental data. The same argument applies to modeling deposition of corrosion products on fuel rods (CRUD). Here are some results from publications in 2016 carried out using the CASL allocation at LANL.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

First-Principles Study of Surface Properties of U{sub 3}Si{sub 2} for Accident Tolerant Fuel

Due to the high thermal conductivity and uranium density compared to UO{sub 2} fuel used in current Light Water Reactors (LWRs), U-Si fuels, such as the U{sub 3}Si{sub 2} and U{sub 3}Si{sub 5} compounds, are currently under investigation for the development of accident tolerant fuels (ATF) in response to the Fukushima Daiichi accident in Japan. In order to perform meaningful mesoscale and macroscale fuel performance simulations, fundamental material properties of nuclear fuels should be known. One example is the simulations of fission gas bubble evolution and gas bubble-induced swelling in nuclear fuels using mesoscale methods, such as phase field and rate theory. To properly describe the gas bubble behavior in the fuel, it is crucial to know the surface energies of the fuel. Unfortunately, there is no study of the surface properties of U{sub 3}Si{sub 2} from both experiment and theory. To this end, we systematically investigate the surface properties of U{sub 3}Si{sub 2} using density functional theory (DFT) based first-principles calculations. Of several low index facets, we studied the (001) and (100) surfaces of tetragonal U{sub 3}Si{sub 2} with all the possible terminations. Since all the studied surfaces are not stoichiometric, we also investigated the effect of elemental chemical potentials on the formation of surface. We systematically investigate the surface properties of U{sub 3}Si{sub 2} using density functional theory calculations. Of several low-index facets, the (001) and (100) surfaces show similar averaged surface energies calculated using even number of layers. At the high Si chemical potential, the Si-terminated U{sub 3}Si{sub 2}(100) and U{sub 3}Si{sub 2}(001) surfaces show lower energies than those of the U-terminated surfaces, with U,Si-terminated U{sub 3}Si{sub 2}(001) as the most stable surface. The surface energies of all non-stoichiometric U{sub 3}Si{sub 2} are linearly dependent on the Si chemical potential. The surface energies of U-terminated surfaces decrease as Si potential decreases. The U{sub 2}-terminated U{sub 3}Si{sub 2}(100) surface becomes that the most stable surface at U-rich side. Based on the current results, an averaged surface energy of U{sub 3}Si{sub 2}, i.e., 1.45 J/m{sup 2}, is recommended for the description of the rounded facets of gas bubbles in U{sub 3}Si{sub 2} by mesoscale simulations. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sticking Coefficients of Fusion Reactor Impurities from Molecular Dynamics Simulations for the Design of Cryopumps

A cryopump can be utilized as an impurity removal component of a direct internal recirculation (DIR) system for the fusion fuel cycle. The DIR facilitates a low fuel inventory by continuously pumping unburnt fuel while removing impurities from the fusion exhaust stream. A cryopump can target multiple impurity species by maintaining a temperature lower than the gas triple-point temperature that promotes desublimation. The desublimation/condensation of gases in cryopumps can be characterized by the sticking coefficient, which is defined as the probability for a gas particle to stick to a (cryo-)surface upon collision. The sticking coefficient is one of the important design/operation parameters for cryopumps, and it depends on a variety of surface and gas properties. Here, in this study, molecular dynamics simulations were utilized to estimate the sticking coefficients of typical fusion gas impurity species N 2 , CO 2 , and CH 4 over a Cu surface for a range of gas temperatures and surface coverages. The molecular dynamics study showed that the sticking coefficients for gases decrease with an increase in gas temperature. The presence of a single full monolayer of condensate on the metallic surface showed an adverse effect on the sticking of gases; however the sticking improved with two full monolayers of condensate on the surface. The sticking of gases over the mixed condensate on a surface was more favorable than the condensate of the same species for N 2 and CH 4 , with an exception for CO 2 , which showed a decrease in sticking over the mixed condensate.

cryopump↗

Assessment of MARMOT Grain Growth Model

This report assesses the MARMOT grain growth model by comparing modeling predictions with experimental results from thermal annealing. The purpose here is threefold: (1) to demonstrate the validation approach of using thermal annealing experiments with non-destructive characterization, (2) to test the reconstruction capability and computation efficiency in MOOSE, and (3) to validate the grain growth model and the associated parameters that are implemented in MARMOT for UO 2 . To assure a rigorous comparison, the 2D and 3D initial experimental microstructures of UO 2 samples were characterized using non-destructive Synchrotron x-ray. The same samples were then annealed at 2273K for grain growth, and their initial microstructures were used as initial conditions for simulated annealing at the same temperature using MARMOT. After annealing, the final experimental microstructures were characterized again to compare with the results from simulations. So far, comparison between modeling and experiments has been done for 2D microstructures, and 3D comparison is underway. The preliminary results demonstrated the usefulness of the non-destructive characterization method for MARMOT grain growth model validation. A detailed analysis of the 3D microstructures is in progress to fully validate the current model in MARMOT.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Spark-Assisted HCCI Residential CHP

A transformative small spark ignition (SI) internal combustion (IC) engine fueled with natural gas was developed for combined heat and power (CHP) applications using a combination of cycle simulations, computational fluid dynamics (CFD) modeling, and engine experiments. The resulting 1 kW CHP engine was demonstrated to achieve 36.1% brake thermal efficiency (BTE) while meeting aggressive exhaust emissions targets using a low-cost three-way catalyst. Starting from a “clean-sheet” design, modeling tools were used to select the optimal engine parameters and operating characteristics. The disruptive technologies developed for the CHP system have a target lifetime of at least 10 years. The engine cost at volume of 10,000 units was estimated to be $\$$1,050. A combination of experimental and simulation results were used to identify a path to the program target of 38.6% BTE. Base engine design parameters (i.e., displacement, speed, bore, stroke, valve timings, and compression ratio) were optimized to reduce friction, heat transfer, and exhaust losses. The base clean sheet prototype engine achieved 32% BTE. Optimization of the lube oil and coolant temperatures added 1.8% BTE. The addition of exhaust gas recirculation added 1.1% BTE. Novel thermal barrier coatings (TBCs) developed over the course of the project added 1.2% BTE. Further improvements in engine friction reduction (1.3% BTE) and improved combustion (1.2% BTE) are estimated to meet the program target 38.6% BTE, while also meeting the stringent criteria pollutant emissions targets.

42 ENGINEERING↗

JT9D-70/59 Improved High Pressure Turbine Active Clearance Control System

The JT9D-70/59 high pressure turbine active clearance control system was modified to provide reduction of blade tip clearance when the system is activated during cruise operation. The modification increased the flow capacity and air impingement effectiveness of the cooling air manifold to augment turbine case shrinkage capability, and increased responsiveness of the airseal clearance to case shrinkage. The simulated altitude engine testing indicated a significant improvement in specific fuel consumption with the modified system. A 1000 cycle engine endurance test showed no unusual wear or performance deterioration effects on the engine or the clearance control system. Rig tests indicated that the air impingement and seal support configurations used in the engine tests are near optimum.

Gaffin, W. O.↗