Search NASA⌕ Search

SEARCH · Search NASA

Results for “MITIGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Applying Sensor Uncertainty Mitigation Schemes to Detect-and-Avoid Systems

Impact of sensor noise on the performance of Detect-And-Avoid (DAA) systems can be reduced by implementing various mitigation schemes. This paper evaluates the Sensor Uncertainty Mitigation (SUM) method, implemented in the Detect and Avoid Alerting Logic for Unmanned Systems (DAIDALUS) algorithm, a reference implementation in the DAA minimum operational performance standards. DAIDALUS SUM performance is evaluated using a few safety and operational suitability metrics and compared with more traditional approaches using static safety buffers. A large number of encounters representative of low-speed unmanned aircraft against non-cooperative manned aircraft are simulated and evaluated. An air-to-air radar model produces representative sensor noise for the DAA system. Results show that increasing the tunable parameters for horizontal and vertical uncertainty in DAIDALUS SUM improves the safety metric at the cost of increasing the number of system alerts leading to increased workload. A range of SUM parameters is recommended as suitable values for the type of operations considered for this work. General trends and optimal SUM configurations were found to be nearly the same for two large and very different encounter data sets.

detect and avoid↗

Mass Mitigation in Structural Designs Via Dynamic Properties

Mass Mitigation in Structural Designs Via Dynamic Properties The reported efforts are focused on mitigating unnecessary mass in aerospace hardware via leveraging dynamic strength of materials and the frequency dependency of strain. Analytically predicted dynamic responses of structures are often applied as static loads in stress analyses that ultimately dictate the weight of a structural design. Assuming a dynamic response is a static load and then comparing resulting stress predictions to a static strength property is a long-standing engineering practice. Doing so is known to be, or is assumed to be, conservative. However, little indication of the order of magnitude of embedded conservatism has been identified. NASA/MSFC efforts in 2011, 2019, 2020, and now in 2021 have begun to qualitatively show the order of magnitude of that conservatism. A quick turnaround engineering method is pursued to leverage the subject facets of physics for the purpose of decreasing the weight of flight hardware. Tests performed using simple beams and significant observations are described.

mass mitigation↗

Dust Mitigation Technology Development for Future Lunar Missions with the Dust Solution Testing Initiative (DuSTI) Project

The jagged, hard, and electro-statically-charged dust on the lunar surface is one of the most significant hazards to human exploration of the Moon. The safety of the crew members and sustainability of habitats, science, and supporting hardware depend on effective dust mitigation techniques and technologies. As NASA pursues a new generation of lunar missions with the Artemis program, the Dust Solution Testing Initiative (DuSTI) project is pursuing dust mitigation solutions by performing tests on promising commercial off the shelf (COTS) technologies over FY21.

dust↗

Eclipse Mitigation Strategies in P/2 Lunar Resonant Orbits

Lunar resonant orbits present several important challenges in terms of trajectory design, insertion, stability and eclipse mitigation. For some mission concepts, the placement of the initial orbital elements is fundamental to overcoming show-stopping performance values such as eclipse duration and orbit lifetime. Lunar resonant orbits need to maintain specific alignments in order to avoid undesired flybys or even recontact with Earth or GEO satellites. This paper presents methods to mitigate long eclipses while preserving achievable lunar resonant orbits that persist in the long term.

Eclipse Mitigation↗

Dust Mitigation Technology Characterization of Coatings and Pliable Cleaners

Lunar Dust. Dust has been identified as one of the most significant hazards to human lunar exploration, but limited testing has been performed on lunar dust mitigation technologies since the Apollo program concluded. The safety of the crewmembers and sustainability of habitats, science, and supporting hardware depend on effective dust mitigation techniques and technologies to prevent dust from degrading hardware and equipment.

dust mitigation↗

Mitigation of Silver Ion Loss from Solution by Polymer Coating of Metal Surfaces, Part IV

Ionic silver (Ag+) biocide is a leading candidate to provide residual microbial control in spacecraft potable water systems, but suffers from rapid concentration loss due to interactions with the metallic storage containers and tubing. One approach to resolve this problem is the coating of metal surfaces with an inert barrier film. In previous reports, we have described our investigations addressing Ag+ loss mitigation and adhesion performance of parylene barrier coatings on coupons of several metal alloys and 316Ltubing under static immersion. In such conditions, parylene-C and -AF4 coatings have shown excellent Ag+loss mitigation and mixed long-term adhesion performance, depending on parylene species and substrate surface chemistry/structure. In Part IV of this series, we report on our work to investigate the performance of parylene-C barrier coatings, under more challenging and realistic conditions, in order to evaluate potential suitability for use. The resilience and associated Ag+ loss with Parylene-C coating on½” (12.7 mm)316L tubing and fittings under medium-term immersion and repeated fitting dis/reassembly were investigated. Potential mechanical challenges to barrier coatings in spacecraft potable water systems were investigated, with two main focuses being identified: liquid flow/pressure cycling in tubing and cyclic operation of bellows in positive-expulsion storage tanks. Two corresponding testbeds for experimental characterization of coating performance were developed. In the Flow/Pressure Testbed System, Ag+ solution will be pumped through internally coated 316L tubing, with optional pressure cycling. In the Bellows Tank Testbed System, an internally coated edge-welded 316L bellows containing Ag+ solution will be cyclically extended and compressed, analogous to the operation of bellows tanks used for potable water storage and delivery on the International Space Station. The design and operation of these testbeds are described. Finally, the Ag+ adsorption and saturation behaviors of Kalrez and Viton, for potential use as seal materials in fittings and other connections, were characterized in limited experiments.

mitigation↗

Dusty Environment Classification and Testing: Dust Mitigation Slide Cleaning Material Study

During the Apollo missions many mechanisms, equipment, and surfaces were contaminated by lunar dust and often negatively affected. The methods used to clear these devices of dust proved ineffective, which led to premature failure in some cases. Systems being designed for upcoming missions to the Moon will need to address the performance degradation risk of dust contamination. Surfaces at risk include thermal control surfaces, solar cells, camera and sensor optics, seals, metal joints and tools, and space suit assemblies. To improve state of the art dust mitigation approaches, the dust mitigation team at NASA Glenn Re-search Center (GRC) explored the effects imposed on substrates during cleaning activities in the presence of lunar dust. The Uniform Dust Deposition System (UDDS) was used to conduct a study of various cleaning techniques on different substrates. Test substrates and cleaning media were selected to represent a wide range of structural and functional materials. Substrates included orthofabric, thermal radiator coating, aluminum, quartz glass, silicone rubber, aluminized Mylar, and FEP. Cleaning materials included cloth wipes, tapes, a brush, and a pliable cleaner concept. Cleaning material / substrate pairs were rated on cleaning efficiency, substrate damage, cleaning material longevity, and ease of use. The best performing cleaning method varied based on application.

dust mitigation↗

Dust Characterization Needs for Dust Mitigation

Unknowns remain regarding several lunar dust characteristics, and the lunar dust mitigation community, in collaboration with the science community, is compiling a list of lunar dust characterization needs. It is expected, through the course of currently planned or future lunar surface mission instrumentation, lab experiments, or analysis, that some of these unknowns will be characterized. This list is derived from several sources including findings from the 2020 publication “The Impact of Lunar Dust on Human Exploration”, NASA-STD-1008, SLS-SPEC-159 DSNE, and known gaps identified within NASA programs and projects. The goal of this information collection process is to create a list of dust characterization needs based on scientific and engineering knowledge gaps that will aid in the design and survival of designed and future systems, and address the challenges related to defining the lunar environment and mitigating lunar dust effects on systems and operations. Examples of dust properties and characterization needs include detailed examination of the finest fraction of lunar regolith as it varies by surface location, understanding dust transfer within natural and induced environments, determination of the effects of the lunar plasma environment with regards to materials and hardware, understand the triboelectric charging effects for activities and hardware in contact with the regolith, including grain to grain electrostatic interactions, and material adhesive properties.

dust mitigation↗

Decision Aid for Conjunction Risk Mitigation by Differential Drag

In the previous five years, the rate of conjunctions that the NASA Conjunction Assessment Risk Analysis (CARA) team processed and analyzed has more than tripled. (NASA CARA, 2024) New missions in the early development phases are now required to plan for dealing with conjunctions under the present space environment, and also projecting forward into a future likely with even further increased utilization of the space environment. Some missions are investigating the possibility of using differential drag to remediate conjunctions without expending limited fuel or for missions without propulsive capabilities. The NASA CARA team studied the historical record of conjunctions to evaluate the circumstances under which differential drag may be successfully applied and have developed a series of tables to use as a decision aid for missions considering differential drag. CARA records all conjunctions of their protected payloads, with historical records starting in 2005 (with significant conjunction events starting to occur on or after 2013). From this record, approximately 7,300 had a probability of collision (Pc) greater than 1 in 10,000, the nominal requirement for a risk mitigation maneuver (RMM) to be made per NASA Procedural Requirements (NPR) 8079.1 (NASA, 2023), at 3 days prior to the time of closest approach, the time analyzed for differential drag efficacy. CARA’s maneuver trade space tool (MTS) was used to prop-agate the primary satellite forward from that decision point with varying degrees of increase to ballistic coefficient (BC), and then recalculate the Pc to evaluate whether or not the conjunction was mitigated (Pc < 3E-6). These results were then binned and sorted along several axes, including altitude, amount of delta-BC, and (pre-maneuver) rate of energy dissipation, to identify underlying patterns. The altitude plot is shown in Figure 1. We found that differential drag was most successful for satellites with perigees below 560 km, and which could adopt an average delta-BC of 2 or greater (that is, increasing their ballistic coefficient by a factor of 3). However, this is a difficult threshold for a mission to clear; very few spacecraft are capable of adopting a high-drag configuration for 72 hours continuously. Planet’s Dove spacecraft use differential drag to remediate conjunctions (Griffith, et al., 2021), and they have a maximum delta-BC factor of 9, but in practice (with mission and charging constraints) they achieve a time-averaged delta-BC that is closer to 2 (Foster, et al., 2017). In contrast, a NASA mission in development reached out to CARA to evaluate the utility of differential drag to remediate potential conjunctions for a spacecraft which is capable of a similar high delta-BC, but with operational constraints that limit their time-averaged delta-BC to less than 1. CARA has developed tables that can be used as decision aids to advise missions-in-development about the best way to utilize their differential drag capabilities. For missions below 560 km with the operational flexibility to devote multiple days to holding a high-drag configuration (or a sufficiently high drag ratio to compensate for limitations on that time), they are able to successfully remediate high-risk conjunctions. Conversely, missions that do not meet these ex-acting criteria – most missions – can instead be advised to use on-board propulsion systems to perform RMMs or to turn their minimum-area face towards the approach vector, thereby reducing Pc at the moment of conjunction. (NASA, 2023)

risk mitigation↗

Decision Aid for Conjunction Risk Mitigation by Differential Drag

In the previous five years, the rate of conjunctions that the NASA Conjunction Assessment Risk Analysis (CARA) team processed and analyzed has more than tripled. (NASA CARA, 2024) New missions in the early development phases are now required to plan for dealing with conjunctions under the present space environment, and also projecting forward into a future likely with even further increased utilization of the space environment. Some missions are investigating the possibility of using differential drag to remediate conjunctions without expending limited fuel or for missions without propulsive capabilities. The NASA CARA team studied the historical record of conjunctions to evaluate the circumstances under which differential drag may be successfully applied and have developed a series of tables to use as a decision aid for missions considering differential drag. Currently, if a CARA-protected mission with maneuvering capabilities is predicted to have a conjunction with probability of collision (Pc) greater than 7E-5 (the default value of the ‘yellow threshold’, which may have some other value agreed by CARA and the mission during the Orbital Collison Avoidance Planning (OCAP) process), CARA will use its Maneuver Trade Space (MTS) tool to evaluate and recommend options for the timing and magnitude of a risk mitigation maneuver (RMM), based on the mission’s capabilities. If the conjunction’s Pc is greater than 1E-4, the ‘red threshold’, then an RMM must be executed per NASA Procedural Requirements (NPR) 8079.1 (NASA, 2023), although missions may execute an RMM even if the Pc is lower. The magnitude of the maneuver is typically a few cm/s, and CARA estimates how many will be required for the mission’s nominal lifetime – typically a few per year – during the OCAP process, to inform the mission’s delta-V requirement. For traditional satellites, this is usually smaller than other requirements for orbit insertion, maintenance, and disposal, but for CubeSats or other small satellite missions, a propulsion system may not provide much more than a few cm/s of delta-V or may not fit at all within the available budget of money, time, size, weight, and/or power (SWaP). Conversely, CubeSats often have deployable solar panels, which offer the capacity to have much higher areas facing some directions than others. Such a mission can instead use ‘differential drag’ to remediate a conjunction -- in other words, change its drag area (usually increasing) to deviate from the predicted collision course. This is how Planet’s Dove spacecraft maintain their formations and remediate conjunction risks without having on-board propulsion (Foster, et al., 2017) (Griffith, et al., 2021). CARA has been developing improvements to MTS to support differential-drag for NASA's missions -- where it is effective. CARA records all conjunctions of their protected payloads, with historical records starting in 2005 (with significant conjunction events starting to occur on or after 2013). From this record, approximately 7,300 had a Pc greater than 1E-4 at 3 days prior to the time of closest approach, the time analyzed for differential drag efficacy. Of those, approximately 4,300 had fully-defined covariance matrices stored for both the primary and secondary objects; this set of conjunctions is the basis for the analysis of this work. CARA’s MTS tool was used to propagate the primary satellite forward from that decision point with varying degrees of increase to ballistic coefficient (BC). Because these conjunctions came from multiple missions, the nondimensional ‘delta-BC’ factor was used to quantify and normalize the increase in ballistic coefficient, defined as follows: Delta-BC = BC_new / BC_old - 1 Positive delta-BC factors represent an increase in drag compared to the nominal attitude, while negative delta-BC factors (to a minimum of -1) represent a decrease in drag. At the conclusion of the differential-drag ‘maneuver’, the Pc was recalculated to evaluate whether or not the conjunction was mitigated (Pc < 3E-6). These results were then binned and sorted along several axes, including altitude, amount of delta-BC, and (pre-maneuver) rate of energy dissipation (EDR), to identify underlying patterns. The altitude plot is shown in Figure 1. To validate this analysis, we consulted the record of a NASA mission which uses differential drag to maintain its orbit and remediate conjunction risk. CARA’s empirical record of the mission’s orbit history suggests it achieves a delta-BC of 2.2. Of the twenty-one RMM plans that were submitted by this mission, eighteen were matched with conjunctions in the historical record; of those, twelve were successfully remediated (final measured Pc < 3E-6), and six were not. This is consistent with the expected efficacy for missions orbiting at that altitude. We are presently simulating this mission’s RMMs with MTS; this work is ongoing, but so far, the MTS results are qualitatively in agreement with the empirical results -- correctly predicting that a maneuver would or would not remediate a conjunction, if not exactly matching the final post-remediation Pc value. We found that differential drag was most successful for satellites with perigees below 560 km, and which could adopt an average delta-BC of 2 or greater (that is, increasing their ballistic coefficient by a factor of 3). However, this is a difficult threshold for a mission to clear; very few spacecraft are capable of adopting a high-drag configuration for 72 hours continuously. Planet’s Dove spacecraft use differential drag to remediate conjunctions (Griffith, et al., 2021), and they have a maximum delta-BC factor of 9, but in practice (with mission and charging constraints) they achieve a time-averaged delta-BC that is closer to 2 (Foster, et al., 2017). A mission’s differential drag utility strongly depends on the operational constraints that has the capacity to limit the time-averaged delta-BC. A mission with a high maximum delta-BC of 5 or more can have an effective delta-BC of less than 1 due to operational constraints such as instrument and solar panel pointing, especially if this constraint results in holding an intermediate drag value for most of its orbit. CARA has developed tables that can be used as decision aids to advise missions-in-development about the best way to utilize their differential drag capabilities. For missions below 560 km with the operational flexibility to devote multiple days to holding a high-drag configuration (or a sufficiently high drag ratio to compensate for limitations on that time), they are -- more likely than not -- able to successfully remediate high-risk conjunctions. Conversely, missions that do not meet these exacting criteria -- most missions -- can instead be advised to use on-board propulsion systems to perform RMMs, or to turn their minimum-area face towards the approach vector, thereby reducing Pc at the moment of conjunction due to the decreased Hard-Body Radius (HBR), that is a strongly correlated variable in the Pc calculations. (NASA, 2023)

conjunction assessment↗

Dusty Environment Classification and Testing: Dust Mitigation Slide Wipes & Tapes

During the Apollo missions many mechanisms, equipment, and surfaces were contaminated by lunar dust and often negatively affected. The methods used to clear these devices of dust proved ineffective, which led to premature failure in some cases. Systems being designed for upcoming missions to the Moon will need to address the performance degradation risk of dust contamination. Surfaces at risk include thermal control surfaces, solar cells, camera and sensor optics, seals, metal joints and tools, and space suit assemblies. To improve state of the art dust mitigation approaches, the dust mitigation team at NASA Glenn Research Center (GRC) explored the effects imposed on substrates during cleaning activities in the presence of lunar dust. The Uniform Dust Deposition System (UDDS) was used to conduct a study of various cleaning techniques on different substrates. Test substrates and cleaning media were selected to represent a wide range of structural and functional materials. Substrates included orthofabric, thermal radiator coating, aluminum, quartz glass, silicone rubber, aluminized Mylar, and FEP. Cleaning materials included cloth wipes, tapes, a brush, and a pliable cleaner concept. Cleaning material / substrate pairs were rated on cleaning efficiency, substrate damage, cleaning material longevity, and ease of use. The best performing cleaning method varied based on application.

lunar simulant↗

Temporary storage of carbon in the biosphere does have value for climate change mitigation: a response to the paper by Miko Kirschbaum

Kirschbaum (Mitig Adapt Strat Glob Change 11:1151 1164, 2006) explores the climatic impact over time of temporarily sequestering carbon from the atmosphere. He concludes that temporary storage of carbon in the terrestrial biosphere achieves effectively no climate-change mitigation . His strongly worded statement begs for a response. This paper argues that Kirschbaum s conclusion is an artifact of the specific perspective of his analysis and his choice of a definition for climate-change impact. Even temporary sinks put us on a lower path for climate change, a path that will not otherwise be accessible. For carbon sinks in the terrestrial biosphere, we argue that sooner is better and longer is better, but even known temporary sinks have value.

54 ENVIRONMENTAL SCIENCES↗

LER control and mitigation: mask roughness induced LER

In the push towards commercialization of extreme-ultraviolet lithography (EUVL), meeting the stringent requirements for line-edge roughness (LER) is increasingly challenging. For the 22-nm half-pitch node and below, the ITRS requires under 1.2 nm LER. Much of this LER is thought to arise from three significant contributors: LER on the mask absorber pattern, LER from the resist, and LER from mask roughness induced speckle. The physical mechanism behind the last contributor is becoming clearer, but how it is affected by the presence of aberrations is less well understood. Here, we conduct a full 2D aerial image simulation analysis of aberrations sensitivities of mask roughness induced LER for the first 37 fringe zernikes. These results serve as a guideline for future LER aberrations control. In examining how to mitigate mask roughness induced LER, we next consider an alternate illumination scheme whereby a traditional dipole's angular spectrum is extended in the direction parallel to the line-and-space mask absorber pattern to represent a 'strip'. While this illumination surprisingly provides merely minimal improvement to the LER as several alternate illumination schemes, overall imaging quality in terms of ILS, NILS, and contrast is improved. While the 22-nm half-pitch node can tolerate significant aberrations from a mask roughness induced LER perspective, total aberration levels for the 16-nm half-pitch node need to be strictly capped at 0.25nm rms to meet the ITRS guidelines. An individual aberrations study for the first 37 fringe zernikes on the 16-nm half-pitch node at the 0.25nm rms level reveals a sensitivity to various forms of spherical aberrations (Z9 & Z25) and quadrafoil (Z28) in particular, under conventional crosspole illumination ({sigma} = 0.10). Compared to conventional dipole or crosspole illuminations, an extended dipole 'strip' illumination scheme offers a way to mitigate mask roughness induced LER, while still maintaining high imaging quality for critical mask levels at the 16-nm half-pitch node.

36 MATERIALS SCIENCE↗

Densification and residual stress induced by CO2 laser-based mitigation of SiO2 surfaces

Knowing the ultimate surface morphology resulting from CO{sub 2} laser mitigation of induced laser damage is important both for determining adequate treatment protocols, and for preventing deleterious intensification upon subsequent illumination of downstream optics. Physical effects such as evaporation, viscous flow and densification can strongly affect the final morphology of the treated site. Evaporation is a strong function of temperature and will play a leading role in determining pit shapes when the evaporation rate is large, both because of material loss and redeposition. Viscous motion of the hot molten material during heating and cooling can redistribute material due to surface tension gradients (Marangoni effect) and vapor recoil pressure effects. Less well known, perhaps, is that silica can densify as a result of structural relaxation, to a degree depending on the local thermal history. The specific volume shrinkage due to structural relaxation can be mistaken for material loss due to evaporation. Unlike evaporation, however, local density change can be reversed by post annealing. All of these effects must be taken into account to adequately describe the final morphology and optical properties of single and multiple-pass mitigation protocols. We have investigated, experimentally and theoretically, the significance of such densification on residual stress and under what circumstances it can compete with evaporation in determining the ultimate post treatment surface shape. In general, understanding final surface configurations requires taking all these factors including local structural relaxation densification, and therefore the thermal history, into account. We find that surface depressions due to densification can dominate surface morphology in the non-evaporative regime when peak temperatures are below 2100K.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Recommendation for Mitigations of the Electron Cloud Instability in the ILC

Electron cloud has been identified as one of the highest priority issues for the international Linear Collider (ILC) Damping Rings (DR). An electron cloud Working Group (WG) has evaluated the electron cloud effect and instability, and mitigation solutions for the electron cloud formation. Working group deliverables include recommendations for the baseline and alternate solutions to the electron cloud formation in various regions of the ILC Positron DR, which is presently assumed to be the 3.2 km design. Detailed studies of a range of mitigation options including coatings, clearing electrodes, grooves and novel concepts, were carried out over the previous several years by nearly 50 researchers, and the results of the studies form the basis for the recommendation. The recommendations are the result of the working group discussions held at numerous meetings and during a dedicated workshop. In addition, a number of items requiring further investigation were identified during the discussions at the Cornell meeting and studies will be carried out at CesrTA, a test accelerator dedicated to electron cloud studies, and other institutions.

43 PARTICLE ACCELERATORS↗

Numerical and probabilistic analysis of asteroid and comet impact hazard mitigation

The possibility of asteroid and comet impacts on Earth has received significant recent media and scientific attention. Still, there are many outstanding questions about the correct response once a potentially hazardous object (PHO) is found. Nuclear munitions are often suggested as a deflection mechanism because they have a high internal energy per unit launch mass. However, major uncertainties remain about the use of nuclear munitions for hazard mitigation. There are large uncertainties in a PHO's physical response to a strong deflection or dispersion impulse like that delivered by nuclear munitions. Objects smaller than 100 m may be solid, and objects at all sizes may be 'rubble piles' with large porosities and little strength. Objects with these different properties would respond very differently, so the effects of object properties must be accounted for. Recent ground-based observations and missions to asteroids and comets have improved the planetary science community's understanding of these objects. Computational power and simulation capabilities have improved such that it is possible to numerically model the hazard mitigation problem from first principles. Before we know that explosive yield Y at height h or depth -h from the target surface will produce a momentum change in or dispersion of a PHO, we must quantify energy deposition into the system of particles that make up the PHO. Here we present the initial results of a parameter study in which we model the efficiency of energy deposition from a stand-off nuclear burst onto targets made of PHO constituent materials.

79 ASTRONOMY AND ASTROPHYSICS↗

Assessing Risk and Driving Risk Mitigation for First-of-a-Kind Advanced Reactors

Planning and decision making amidst programmatic and technological risks represent significant challenges for projects. This presentation addresses the four step risk-assessment process needed to determine clear path forward to mature needed technology and design, license, and construct advanced nuclear power plants, which have never been built before, including Small Modular Reactors. This four step process has been carefully applied to the Next Generation Nuclear Plant. STEP 1 - Risk Identification Risks are identified, collected, and categorized as technical risks, programmatic risks, and project risks, each of which result in cost and schedule impacts if realized. These include risks arising from the use of technologies not previously demonstrated in a relevant application. These risks include normal and accident scenarios which the SMR could experience including events that cause the disablement of engineered safety features (typically documented in Phenomena Identification Ranking Tables (PIRT) as produced with the Nuclear Regulatory Commission) and design needs which must be addressed to further detail the design. Product - Project Risk Register contained in a database with sorting, presentation, rollup, risk work off functionality similar to the NGNP Risk Management System . STEP 2 - Risk Quantification The risks contained in the risk register are then scored for probability of occurrence and severity of consequence, if realized. Here the scoring methodology is established and the basis for the scoring is well documented. Product - Quantified project risk register with documented basis for scoring. STEP 3 - Risk Handling Strategy Risks are mitigated by applying a systematic approach to maturing the technology through Research and Development, modeling, test, and design. A Technology Readiness Assessment is performed to determine baseline Technology Readiness Levels (TRL). Tasks needed to mature the technology are developed and documented in a roadmap. Product - Risk Handling Strategy. STEP 4 - Residual Risk Work off The risk handling strategy is entered into the Project Risk Allocation Tool (PRAT) to analyze each task for its ability to reduce risk. The result is risk-informed task prioritization. The risk handling strategy is captured in the Risk Management System, a relational database that provides conventional database utility, including data maintenance, archiving, configuration control, and query ability. The tool's Hierarchy Tree allows visualization and analyses of complex relationships between risks, risk mitigation tasks, design needs, and PIRTs. Product - Project Risk Allocation Tool and Risk Management System which depict project plan to reduce risk and current progress in doing so.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Further RAGE modeling of asteroid mitigation: surface and subsurface explosions in porous objects

Disruption or mitigation of a potentially hazardous object (PHO) by a high-energy subsurface burst is considered. This is just one possible method of impact-hazard mitigation. We present RAGE hydrocode models of the shock-generated disruption of PHOs by subsurface nuclear bursts using scenario-specific models from realistic RADAR shape models. We will show 2D and 3D models for the disruption by a large energy source at the center of such PHO models ({approx}100 kt-10 Mt) specifically for the shape of the asteroid 25143 Itokawa. We study the effects of non-uniform composition (rubble pile), shallow buried bursts for the optimal depth of burial and porosity.

99 GENERAL AND MISCELLANEOUS↗