Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mix Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Tank 21 and tank 24 blend and feed study: blending times, settling times, and transfers

The Salt Disposition Integration (SDI) portfolio of projects provides the infrastructure within existing Liquid Waste facilities to support the startup and long term operation of the Salt Waste Processing Facility (SWPF). Within SDI, the Blend and Feed Project will equip existing waste tanks in the Tank Farms to serve as Blend Tanks where salt solutions of up to 1.2 million gallons will be blended in 1.3 million gallon tanks and qualified for use as feedstock for SWPF. In particular, Tanks 21 and 24 are planned to be used for blending and transferring to the SDI feed tank. These tanks were evaluated here to determine blending times, to determine a range of settling times for disturbed sludge, and to determine that the SWPF Waste Acceptance Criteria that less than 1200 mg/liter of solids will be entrained in salt solutions during transfers from the Tank 21 and Tank 24 will be met. Overall conclusions for Tank 21 and Tank 24 operations include: (1) Experimental correction factors were applied to CFD (computational fluid dynamics) models to establish blending times between approximately two and five hours. As shown in Phase 2 research, blending times may be as much as ten times greater, or more, if lighter fluids are added to heavier fluids (i.e., water added to salt solution). As the densities of two salt solutions converge this effect may be minimized, but additional confirmatory research was not performed. (2) At the current sludge levels and the presently planned operating heights of the transfer pumps, solids entrainment will be less than 1200 mg/liter, assuming a conservative, slow settling sludge simulant. (3) Based on theoretical calculations, particles in the density range of 2.5 to 5.0 g/mL must be greater than 2-4 {micro}m in diameter to ensure they settle adequately in 30-60 days to meet the SWPF feed criterion (<1200 mg/l). (4) Experimental tests with sludge batch 6 simulant and field turbidity data from a recent Tank 21 mixing evolution suggest the solid particles have higher density and/or larger size than indicated by previous analysis of SRS sludge and sludge simulants. (5) Tank 21 waste characterization, laboratory settling tests, and additional field turbidity measurements during mixing evolutions are recommended to better understand potential risk for extended (> 60 days) settling times in Tank 21.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A new high-order spectral difference method for simulating viscous flows on unstructured grids with mixed-element meshes

In the present study, a spectral difference (SD) method is developed for viscous flows on meshes with a mixture of triangular and quadrilateral elements. The standard SD method for triangular elements, which employs Lagrangian interpolating functions for fluxes, is not stable when the designed accuracy of spatial discretization is third order or higher. Unlike the standard SD method, the method examined here uses vector interpolating functions in the Raviart-Thomas (RT) spaces to construct continuous flux functions on reference elements. The spectral-difference Raviart-Thomas (SDRT) method was originally proposed by Balan et al. and implemented on triangular-element meshes for invisid flow only. Our present results demonstrated that the SDRT method is stable and high-order accurate in two dimensions (2D) for a number of test problems by using triangular-, quadrilateral-, and mixed-element meshes for both inviscid and viscous flows. A stability analysis is also performed for mixed elements. Furthermore, we found our current SDRT scheme is stable for fourth-order accurate spatial discretizations. However, a stable fifth-order SDRT scheme remains to be identified.

97 MATHEMATICS AND COMPUTING↗

X-ray absorption spectroscopy study of parent misfit-layered cobalt oxide [Sr₂O₂] q }CoO₂

Here we present a comprehensive X-ray absorption spectroscopy study carried out at Co-L₂,₃, Co-K, O-K and Sr-K edges for the parent misfit-layered cobalt oxide phase [Sr₂O₂]₀.₅₂CoO₂; comparison is made to another misfit-layered oxide [CoCa₂O₃]₀.₆₂CoO₂ and the perovskite oxide LaCoO₃. A high-quality sample of [Sr₂O₂]₀.₅₂CoO₂ was obtained through ultra-high-pressure synthesis using Sr₃Co₂O₆ and Sr(OH)₂∙8H₂O as starting materials. Different dosages of KClO₃ were mixed with the raw materials as an oxygen source and tested, but it was found that the window for the redox control of [Sr₂O₂]₀.₅₂CoO₂ is rather narrow. From Co-K and Co-L₂,₃ spectra a mixed III/IV valence state is revealed for cobalt in [Sr₂O₂]₀.₅₂}CoO₂, but the average valence value is a little lower than in [CoCa₂O₃]₀.₆₂CoO₂. Then, Sr-K spectrum indicates that the [Sr₂O₂] double-layer block in [Sr₂O₂]₀.₅₂CoO₂ clearly deviates from the cubic SrO rock-salt structure, suggesting a more complicated coordination environment for strontium. This together with a somewhat low Co-valence value and the fact that the phase formation of [Sr₂O₂]₀.₅₂CoO₂ required the presence of Sr(OH)₂∙8H₂O in the high-pressure synthesis suggest that the [Sr₂O₂] block contains ---OH groups, i.e. [Sr₂(O,OH)₂]₀.₅₂CoO₂. - Graphical abstract: [Sr₂O₂]₀.₅₂CoO₂ obtained through high-pressure synthesis is a parent of misfit-layered cobalt oxides, such as [CoCa₂O₃]₀.₆₂CoO₂ or [M m A₂O 2+m ] q CoO₂ in general. Our comprehensive X-ray absorption spectroscopy study shows that both [Sr₂O₂]₀.₅₂CoO₂ and [CoCa₂O₃]₀.₆₂CoO₂ possess mixed III/IV valence cobalt, but the average Co-valence is a little lower in the former. This is tentatively believed to be due to OH --- groups replacing part of O²⁻ ions in the [Sr₂O₂] layer block. Highlights: • [Sr₂O₂]₀.₅₂CoO₂ is a parent of misfit-layered cobalt oxides. • It is obtained by ultra-high-pressure synthesis from Sr₃Co₂O₆, Sr(OH)₂∙6H₂O and KClO₃. • Co-K and Co---L XANES spectra reveal lower than expected Co-valence value. • Sr-K XANES spectrum indicates that the [Sr₂O₂] block is not of simple rock-salt structure. • This block most probably contains ---OH --- groups, i.e. [Sr₂(O,OH)₂]₀.₅₂CoO₂.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Testing CPT invariance in B{sub d}{sup 0}-B{sub d}{sup 0} and B{sub s}{sup 0}-B{sub s}{sup 0} oscillations

Recent CDF and D0 measurements of B{sub s}{sup 0}-B{sub s}{sup 0} mixing make it possible to search for CP violation and test CPT symmetry in a variety of B{sub s} decays. Considering both coherent B{sub d}{sup 0}B{sub d}{sup 0} decays at the {upsilon}(4S) resonance and coherent B{sub s}{sup 0}B{sub s}{sup 0} decays at the {upsilon}(5S) resonance, we formulate their time-dependent and time-integrated rates by postulating small CPT violation in B{sub d}{sup 0}-B{sub d}{sup 0} and B{sub s}{sup 0}-B{sub s}{sup 0} oscillations. We show that the opposite-sign dilepton events from either C-odd or C-even B{sub q}{sup 0}B{sub q}{sup 0} states (for q=d or s) can be used to determine or constrain the CPT-violating parameter at a super-B factory. The possibility of distinguishing between the effect of CPT violation and that of {delta}B=-{delta}Q transitions is also discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Understanding the branching ratios of {chi}{sub c1{yields}{phi}{phi}}, {omega}{omega}, {omega}{phi} observed at BES-III

In this work, we discuss the contribution of the mesonic loops to the decay rates of {chi}{sub c1{yields}{phi}{phi}}, {omega}{omega}, which are suppressed by the helicity selection rules and {chi}{sub c1{yields}{phi}{omega}}, which is a double-Okubo-Zweig-Iizuka forbidden process. We find that the mesonic loop effects naturally explain the clear signals of {chi}{sub c1{yields}{phi}{phi}}, {omega}{omega} decay modes observed by the BES Collaboration. Moreover, we investigate the effects of the {omega}-{phi} mixing, which may result in the order of magnitude of the branching ratio BR({chi}{sub c1{yields}{omega}{phi}}) being 10{sup -7}. Thus, we are waiting for the accurate measurements of the BR({chi}{sub c1{yields}{omega}{omega}}), BR({chi}{sub c1{yields}{phi}{phi}}), and BR({chi}{sub c1{yields}{omega}{phi}}), which may be very helpful for testing the long-distant contribution and the {omega}-{phi} mixing in {chi}{sub c1{yields}{phi}{phi}}, {omega}{omega}, {omega}{phi} decays.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

FABRICATION PROCESS AND PRODUCT QUALITY IMPROVEMENTS IN ADVANCED GAS REACTOR UCO KERNELS

A major element of the Advanced Gas Reactor (AGR) program is developing fuel fabrication processes to produce high quality uranium-containing kernels, TRISO-coated particles and fuel compacts needed for planned irradiation tests. The goals of the AGR program also include developing the fabrication technology to mass produce this fuel at low cost. Kernels for the first AGR test (“AGR-1) consisted of uranium oxycarbide (UCO) microspheres that werre produced by an internal gelation process followed by high temperature steps tot convert the UO3 + C “green” microspheres to first UO2 + C and then UO2 + UCx. The high temperature steps also densified the kernels. Babcock and Wilcox (B&W) fabricated UCO kernels for the AGR-1 irradiation experiment, which went into the Advance Test Reactor (ATR) at Idaho National Laboratory in December 2006. An evaluation of the kernel process following AGR-1 kernel production led to several recommendations to improve the fabrication process. These recommendations included testing alternative methods of dispersing carbon during broth preparation, evaluating the method of broth mixing, optimizing the broth chemistry, optimizing sintering conditions, and demonstrating fabrication of larger diameter UCO kernels needed for the second AGR irradiation test. Based on these recommendations and requirements, a test program was defined and performed. Certain portions of the test program were performed by Oak Ridge National Laboratory (ORNL), while tests at larger scale were performed by B&W. The tests at B&W have demonstrated improvements in both kernel properties and process operation. Changes in the form of carbon black used and the method of mixing the carbon prior to forming kernels led to improvements in the phase distribution in the sintered kernels, greater consistency in kernel properties, a reduction in forming run time, and simplifications to the forming process. Process parameter variation tests in both forming and sintering steps led to an increased understanding of the acceptable ranges for process parameters and additional reduction in required operating times. Another result of this test program was to double the kernel production rate. Following the development tests, approximately 40 kg of natural uranium UCO kernels have been produced for use in coater scale up tests, and approximately 10 kg of low enriched uranium UCO kernels for use in the AGR-2 experiment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Sensor Arrays and Packaging

Novel sensor packaging elements were designed, fabricated, and tested in order to facilitate the transition of electrochemical mixed-potential sensors toward commercialization. Of the two designs completed, the first is currently undergoing field trials, taking direct measurements within vehicle exhaust streams, while the second is undergoing preliminary laboratory testing. The sensors’ optimal operating conditions, sensitivity to hydrogen, and long-­term baseline stability were also investigated. The sensing capabilities of lanthanum chromite (La 0.8 Sr 0.2 CrO 3 ) and indium-­doped tin oxide (ITO) working electrodes were compared, and the ITO devices were selected for pre-­commercial field trials testing at a hydrogen fuel cell vehicle fueling station in California. Previous data from that fueling station were also analyzed, and the causes of anomalous baseline drift were identified.

47 OTHER INSTRUMENTATION↗

Determination of the weak charge of the proton through parity violating asymmetry measurements in the elastic e+p scattering

The Qweak experiment has taken data to make a 2.5% measurement of parity violating elastic e+p asymmetry in the four momentum transfer region of 0.0250 (GeV/c) 2 . This asymmetry is proportional to the weak charge of the proton, which is related to the weak mixing angle, sin 2 (theta_W). The final Qweak measurement will provide the most precise measurement of the weak mixing angle below the Z 0 pole to test the Standard Model prediction. A description of the experimental apparatus is provided in this dissertation. The experiment was carried out using a longitudinally polarized electron beam of up to 180 microampere on a 34.5 cm long unpolarized liquid hydrogen target. The Qweak target is not only the world's highest cryogenic target ever built for a parity experiment but also is the least noisy target. This dissertation provides a detailed description of this target and presents a thorough analysis of the target performance. Statistical analysis of Run 1 data, collected between Feb - May 2011, is done to extract a blinded parity violating asymmetry of size -299.7 ± 13.4 (stat.) ± 17.2 (syst.) ± 68 (blinding) parts-per-billion. This resulted in a preliminary proton's weak charge of value 0.0865 ± 0.0085, a 9% measurement. Based on this blinded asymmetry, the weak mixing angle was determined to be sin 2 (theta_W) = 0.23429 ± 0.00211.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Resistance of fly ash-Portland cement blends to thermal shock

Thermal-shock resistance of high-content fly ash-Portland cement blends was tested in the following ways. Activated and non-activated blends with 80-90 % fly ash F (FAF) were left to set at room temperature, then hydrated for 24 hours at 85°C and 24-more hours at 300°C and tested in five thermal-shock cycles (600°C heat - 25°C water quenching). XRD, and thermal gravimetric analyses, along with calorimetric measurements and SEM-EDX tests demonstrated that the activated blends form more hydrates after 24 hours at 300°C, and achieve a higher short-term compressive strength than do non-activated ones. Sodium meta-silicate and sodaash engendered the concomitant hydration of OPC and FAF, with the formation of mixed crystalline FAF-OPC hydrates and FAF hydrates, such as garranite, analcime, and wairakite, along with the amorphous FAF hydration products. In SS-activated and non-activated blends separate OPC (tobermorite) and FAF (amorphous gel) hydrates with no mixed crystalline products formed. The compressive strength of all tested blends decreased by nearly 50% after 5 thermal-shock test cycles. These changes in the compressive strength were accompanied by a marked decrease in the intensities of XRD patterns of the crystalline hydrates after the thermalshock. As a result, there was no significant difference in the performance of the blends with different activators

15 GEOTHERMAL ENERGY↗

Ionization Gas Sensor using Aligned Multiwalled Carbon Nanotubes Array

The challenge with current conventional gas sensors which are operating using semiconducting oxides is their size. After the introduction of nanotechnology and in order to reduce the dimension and consequently the power consumption and cost, new materials such as carbon nanotubes (CNTs) are being introduced. From previous works and characterization results, it was proven that the CNTs based gas sensor has better sensitivity, selectivity and faster response time in compared with semiconducting oxides based gas sensors. As in this work, a fabrication and successful testing of an ionization-based gas sensor using aligned Multiwalled CNTs (MWCNTs) as sensing element is discussed, in which MWCNTs array and Al film are used as anode and cathode plates respectively with electrode separation ranging from 80 {mu}m to 140 {mu}m. Aligned MWCNTs array was incorporated into a sensor configuration in the gas chamber for testing of gases such as argon, air, and mixed gas of 2%H{sub 2} in air. Obtained results show that among the three gases, argon has the lowest breakdown voltage whilst air has the highest value and the breakdown voltage was found to decrease as the electrode spacing was reduced from 140 {mu}m to 80 {mu}m for all three gases.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Antifoam Development for Eliminating Flammability Hazards and Decreasing Cycle Time in the Defense Waste Processing Facility

The Savannah River National Laboratory (SRNL) was requested to develop a new antifoam control method for the Defense Waste Processing Facility’s (DWPF) Chemical Process Cell (CPC). SRNL completed testing of both chemical and nonchemical foam controls. The nonchemical foam controls were either ineffective (or worse, created more foam) or impractical (a water spray can control foam, but excessive water is needed). As a result, the focus of this study was on finding a superwetter or commercial antifoam for controlling foam. Thirty potential antifoams were tested as part of this study. A series of tests were developed to help screen out ineffective alternatives including: 1. Spreading testing of superspreaders, 2. Foam column testing with physical simulants, 3. Boiling testing with physical and chemical simulants, 4. Days-only Sludge Receipt and Adjustment Tank (SRAT) process simulations with sludge (containing noble metals and mercury), Precipitate Reactor Feed Tank (PRFT), and Slurry Mix Evaporator Feed Tank (SEFT) simulants in the RC1 Reaction Calorimeter (purchased for antifoam testing), and 5. Around-the-clock SRAT and Slurry Mix Evaporator (SME) process simulations with sludge(containing noble metals and mercury), PRFT, and SEFT simulants in the RC1 Reaction Calorimeter. Evonik Surfynol® MD20, a commercially available defoamer, was relatively effective in controlling foam, while remaining chemically stable in SRAT and SME processing across the pH range of 4 to 13. No degradation products were detected in the offgas, in the condensate or in the SRAT and SME products. In nitric-glycolic acid flowsheet testing, 250 mg/kg Evonik Surfynol® MD20 was needed for foam control compared to 1,625 mg/kg for Antifoam 747, DWPF’s current antifoam. In nitric-formic acid flowsheet testing, 1,125 mg/kg of Evonik Surfynol® MD20 was needed to control foam throughout the SRAT and SME cycles. The commercially available superspreader Momentive™ Y-17112 was even more effective than Evonik Surfynol® MD20 as both a defoamer and an antifoam. Not only was the foam destroyed upon addition but also was less persistent between additions. It was the most effective antifoam in testing using both the nitric-glycolic acid flowsheet and the nitric-formic acid flowsheet. In nitric-glycolic acid flowsheet testing, only 100 mg/kg Momentive™ Y-17112 was needed to control foam throughout the SRAT and SME cycles. In nitric-formic acid flowsheet testing, 300 mg/kg Momentive™ Y-17112 was needed to control foam throughout the SRAT and SME cycles. Momentive™ Y-17112 is also resistant to hydrolysis as demonstrated by its chemical stability in SRAT and SME processing across the pH range of 4 to 13 and lack of degradation products in offgas or condensate. Both candidates were effective as potential replacements for Antifoam 747, with Y-17112 demonstrating superior foam control. During nitric-glycolic flowsheet testing 50% less antifoam was needed when using Momentive™ Y-17112 compared to MD20. During nitric-formic flowsheet testing 75% less antifoam was needed when using Momentive™ Y-17112 compared to MD20. Foam remediated with Momentive™ Y-17112 was less persistent throughout testing. In addition, no degradation products were detected in the offgas, in the condensate or in the SRAT and SME products. Based on this testing, Momentive™ Y-17112 is clearly superior to Evonik Surfynol® MD20 and Antifoam 747, especially for the nitric-formic acid flowsheet processing; it is recommended that Momentive™ Y-17112 replace Antifoam 747 in DWPF. An antifoam addition strategy is recommended for both the nitric-glycolic acid flowsheet and the nitric-formic acid flowsheet. Implementation of Momentive™ Y-17112 is expected to decrease SRAT and SME boiling times by up to 50%, eliminate the issues resulting from Antifoam 747 degradation products, and minimize foamovers. To validate the effectiveness of these defoaming agents, SRNL recommends irradiation of a SRAT or SME product simulant containing fresh antifoam. The goal of this testing is to determine whether the irradiation causes decomposition of the antifoam that would make it less effective or produce new species in the offgas or slurry. This testing began in April 2020. An evaluation should be completed to determine the thermolytic hydrogen and methane generation rate in downstream equipment, including the High-Level Waste evaporators.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A single-column particle-resolved model for simulating the vertical distribution of aerosol mixing state: WRF-PartMC-MOSAIC-SCM v1.0

Abstract. The PartMC-MOSAIC particle-resolved aerosol model was previously developed to predict the aerosol mixing state as it evolves in the atmosphere. However, the modeling framework was limited to a zero-dimensional box model approach without resolving spatial gradients in aerosol concentrations. This paper presents the development of stochastic particle methods to simulate turbulent diffusion and dry deposition of aerosol particles in a vertical column within the planetary boundary layer. The new model, WRF-PartMC-MOSAIC-SCM, resolves the vertical distribution of aerosol mixing state. We verified the new algorithms with analytical solutions for idealized test cases and illustrate the capabilities with results from a 2-day urban scenario that shows the evolution of black carbon mixing state in a vertical column.

54 ENVIRONMENTAL SCIENCES↗

Effect of specimen size on fracture energy and softening curve of concrete: Part I. Experiments and fracture energy

The fracture energy of concrete G{sub F} is a fundamental fracture parameter, presenting the concrete's cracking resistance. However, because of the experimentally observed size dependency, it remains controversial as to whether the fracture energy can be considered as a material property. In this study, a three-point bend test for a notched beam and a wedge splitting test were performed with different size specimens for ten different concrete mixes in order to investigate the effect of specimen size and geometry on the fracture energy. A data processing method was proposed for averaging the test results of companion specimens, and the fracture energy was calculated from the averaged results. From a comparison of the fracture energies, it was found that the fracture energy increases with an increase in specimen size in both the beam and wedge splitting tests.

36 MATERIALS SCIENCE↗

PARAMETRIC EFFECTS OF ANTI-FOAM COMPOSITION, SIMULANT PROPERTIES AND NOBLE METALS ON THE GAS HOLDUP AND RELEASE OF A NON-NEWTONIAN WASTE SLURRY SIMULANT

Gas holdup tests were performed in bench-scale and small-scale mechanically-agitated mixing systems at the Savannah River National Laboratory (SRNL) for a simulant of waste from the Hanford Tank 241-AZ-101. These featured additions of DOW Corning Q2-3183A anti-foam agent. Results indicated that this anti-foam agent (AFA) increased gas holdup in the waste simulant by about a factor of four and, counter-intuitively, that the holdup increased as the non-newtonian simulant shear strength decreased (apparent viscosity decreased). Such results raised the potential of increased flammable gas retention in Hanford Waste Treatment and Immobilization Plant (WTP) vessels mixed by air sparging and pulse-jet mixers (PJMs) during a Design Basis Event (DBE). Additional testing was performed to determine the effects of simulant properties, composition of alternate AFAs, and presence of trace noble metals. Key results are that: (1) Increased gas holdup resulting from addition of Q2-3183A is due to a decrease in surface tension that supports small bubbles which have low rise velocities. (2) Dow Corning 1520-US AFA shows it to be a viable replacement to Dow Corning Q2-3183A AFA. This alternative AFA, however, requires significantly higher dosage for the same anti-foam function. (3) Addition of noble metals to the AZ-101 waste simulant does not produce a catalytic gas retention effect with the AFA.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

FY2019 ILAW Glass Ion Exchange Rate Testing (Final Report)

About 50 million gallons of high-level mixed waste is currently stored in underground tanks at The United States Department of Energy’s (DOE’s) Hanford site in the State of Washington. The Hanford Tank Waste Treatment and Immobilization Plant (WTP) will provide DOE’s Office of River Protection (ORP) with a means of treating this waste by vitrification for subsequent disposal. The tank waste will be separated into low- and high-activity waste fractions, which will then be vitrified respectively into Immobilized Low Activity Waste (ILAW) and Immobilized High-Level Waste (IHLW) products. The ILAW product will be disposed of in an engineered facility - the Integrated Disposal Facility (IDF) - on the Hanford site, while the IHLW product is designed for acceptance into a national deep geological disposal facility for high-level nuclear waste. The ILAW and IHLW products must meet a variety of requirements with respect to protection of the environment before they can be accepted for disposal.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Impacts of Rotational Mixing on the Precipitation Simulated by a Convection Permitting Model

With increased availability of computational resources, regional and global scale convection-permitting model (CPM, Δx ~ 1–10 km) simulations are becoming more common. CPMs have improved accuracy in their representation of deep convection and mesoscale convective systems (MCSs) compared to coarser resolution models. However, CPMs still exhibit convective cloud and precipitation biases relative to observations, notably a lesser frequency of light precipitation rates and greater frequency of heavy precipitation rates. In this work we hypothesize that these CPM biases are related to under-resolved mixing between convective updrafts and their surrounding environment. To test this hypothesis, we introduce a parameterization to the Weather Research and Forecasting model (WRF) that adds a small angular rotation of the grid-scale flow about the axis perpendicular to the plane of convective drafts. This rotated flow is then allowed to alter advection of moisture and hydrometeors. The effects of such mixing on precipitation characteristics are evaluated in month-long 4-km grid spacing simulations over the Amazon. The enhanced mixing transports moisture and condensate from convective cores to other areas including downdrafts. This increases the frequency of low-precipitable water and light precipitation. It also decreases the frequency of intense precipitation from isolated deep convection and MCSs, increases cloud top temperatures, reduces radar echo-top heights, and increases overall precipitation by altering the relationship of precipitation with precipitable water, in better agreement with observations. The results suggest when optimized using multiple observations, such an approach may provide a path toward more accurate representation of convection and precipitation statistics in convection-permitting simulations.

54 ENVIRONMENTAL SCIENCES↗

Knock Intensity Distribution and a Stochastic Control Framework for Knock Control

One of the main factors limiting the efficiency of spark-ignited (SI) engines is the occurrence of engine knock. In high temperature and high pressure in-cylinder conditions, the fuel–air mixture auto-ignites creating pressure shock waves in the cylinder. Knock can significantly damage the engine and hinder its performance; as such, conservative knock control strategies are generally implemented which avoid such operating conditions at the cost of lower thermal efficiencies. Significant improvements in the performance of conventional knock controllers are possible if the properties of the knock process are better characterized and exploited in knock controller designs. One of the methods undertaken to better characterize knocking instances is to employ a probabilistic approach, in which the likelihood of knock is derived from the statistical distribution of knock intensity (KI). In this paper, it is shown that KI values at a fixed operating point for single fuel and dual fuel engines are accurately described using a mixed lognormal distribution. The fitting accuracy is compared against those for a randomly generated mixed-lognormally distributed dataset, and shown to exceed a 95% accuracy threshold for almost all of the operating points tested. Additionally, this paper discusses a stochastic knock control approach that leverages the mixed lognormal distribution to adjust spark timing based on KI measurements. Overall, this more informed knock control strategy would allow for improvements in engine performance and fuel efficiency by minimizing knock occurrences.

42 ENGINEERING↗

Mixed Alcohol Synthesis Catalyst Screening 2007 Progress Report

Pacific Northwest National Laboratory (PNNL) and National Renewable Energy Laboratory (NREL) are researching the feasibility of producing mixed alcohols from biomass-derived synthesis gas (syngas). PNNL is obtaining commercially available mixed alcohol or preparing promising mixed-alcohol catalysts and screening them in a laboratory-scale reactor system. The most promising catalysts are provided to NREL for testing using a slipstream from a pilot-scale biomass gasifier. After a review of the literature in 2006 and conversations with companies that produce catalysts, it was determined that no commercial mixed-alcohol synthesis catalysts were available. One manufacturer supplied a modified methanol catalyst that was tested in the PNNL laboratory-scale system and provided to NREL for further testing. PNNL also prepared and tested the behavior of 10 other catalysts representing the distinct catalyst classes for mixed alcohol syntheses. Based on those results,testing in 2007 focused on the performance of the rhodium-based catalysts. The effects of adding promoters to the rhodium catalysts in addition to the manganese already being used were examined. The iron and rhenium promoters both stood out as achieving higher carbon selectivities , followed by Cu. Iridium and Li, on the other hand, had low carbon selectivity ratios of 0.27 and 0.22, respectively. Although testing of candidate promoters is not complete, it appears that Ir and Li promoters warrant further optimization and possibly combination to further improve STYs and carbon selectivities to C2+ oxygenates. However, using these promoters, it will be necessary to incorporate a separate hydrogenation catalyst to improve the yield of C2+ alcohols with respect to the other oxygenates. Fe, Re, and Cu stand out as possible candidates in this respect, but additional research is needed to examine whether they can be combined with the other promoters on the Rh-based catalyst or need to be optimized on a separate catalyst support that is either physically mixed or used in series with the promoted Rh-based catalyst.

09 BIOMASS FUELS↗