SEARCH · Search NASA

Results for “PLATES - BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

All sources NASA NTRS DOE OSTI

NASA NTRS1988

North America-Pacific plate boundary, an elastic-plastic megashear - Evidence from very long baseline interferometry

Data obtained by Mark III VLBI measurements of radio signals from permanent and mobile VLBI sites for 5.5 years of observations, starting in October 1982, were used to derive a picture of the earth crust deformation near the North America-Pacific plate boundary. The data, which included the vector positions of the VLBI sites and their rate of change, were used for comparison with a number of lithospheric deformation models based upon the concept that the motions of points near the North America-Pacific plate boundary are a linear combination of North America and Pacific velocities. The best of these models were found to fit 95 percent of the variance in 139 VLBI length and transverse velocity observations. Instantaneous shear deformation associated with plate tectonics is apparently developing in a zone 450 km wide paralleling the San Andreas Fault; some of this deformation will be recovered through elastic rebound, while the rest will be permanently set through plastic processes. Because the VLBI data have not been collected for a significant fraction of the earthquake cycle, they cannot discriminate between elastic and plastic behaviors.

Ward, Steven N.↗

NASA NTRS1988

Interference effects on the hypersonic, rarefied flow about a flat plate

The Direct Simulation Monte Carlo method is used to study the hypersonic, rarified flow interference effects on a flat plate caused by nearby surfaces. Calculations focus on shock-boundary-layer and shock-lip interactions in hypersonic inlets. Results are presented for geometries consisting of a flat plate with different leading-edge shapes over a flat lower wall and a blunt-edge flat plate over a 5-degree wedge. The problems simulated correspond to a typical entry flight condition of 7.5 km/s at altitudes of 75 to 90 km. The results show increases in predicted local heating rates for shock-boundary-layer and shock-lip interactions that are quantitatively similar to those observed experimentally at much higher densities.

Wilmoth, Richard G.↗

NASA NTRS1989

Friction factor data for flat plate tests of smooth and honeycomb surfaces

Friction factors for honeycomb surfaces were measured with a flat plate tester. The flat plate test apparatus was described and a method was discussed for determining the friction factor experimentally. The friction factor model was developed for the flat plate test based on the Fanno Line Flow. The comparisons of the friction factor were plotted for smooth surfaces and six-honeycomb surfaces with three-clearances, 6.9 bar to 17.9 bar range of inlet pressures, and 5,000 to 100,000 range of the Reynolds number. The optimum geometries for the maximum friction factor were found as a function of cell width to cell depth and cell width to clearance ratios.

Ha, Tae Woong↗

NASA NTRS1988

Line spring model and its applications to part-through crack problems in plates and shells

The line spring model is described and extended to cover the problem of interaction of multiple internal and surface cracks in plates and shells. The shape functions for various related crack geometries obtained from the plane strain solution and the results of some multiple crack problems are presented. The problems considered include coplanar surface cracks on the same or opposite sides of a plate, nonsymmetrically located coplanar internal elliptic cracks, and in a very limited way the surface and corner cracks in a plate of finite width and a surface crack in a cylindrical shell with fixed end.

Erdogan, Fazil↗

NASA NTRS1988

Automated design of composite plates for improved damage tolerance

The present effort toward design automation for local damage tolerance in composite plates under compressive loading, simulating the local damage condition by a central, through-the-thickness crack-like notch, uses a micromechanical failure model for the fiber kink formation in the load-carrying layers. This accounts for the combined effects of compressive and shearing stresses around the notch. For stiffened plates, minimum-weight configurations are obtained where the crack is isolated in low stiffness plate regions.

Gurdal, Zafer↗

NASA NTRS1989

Analysis of multilayered anisotropic plates - A new look at an old problem

The paper is concerned with the effects of variation in the lamination and geometric parameters of multilayered anisotropic plates on the accuracy of the static and vibrational responses predicted by six modeling approaches based on two-dimensional shear deformation theories. Extensive numerical results are presented for antisymmetrically laminated anisotropic rectangular plates. It is shown that, for most practical problems, the transverse shear deformation has a much more pronounced effect on the response of multilayered composite plates than that of transverse normal strain and stress. It is also shown that the accuracy of the predictions of the first-order deformation theory is strongly dependent on the values of the composite shear correction factors used.

Noor, Ahmed K.↗

NASA NTRS1989

Stress and free vibration analyses of multilayered composite plates

This paper presents a two-phase computational procedure for the accurate prediction of vibration frequencies, stresses, and deformations in simply supported bidirectional multilayered composite plates. The range of applicability of this procedure in terms of the plate's parameters is determined, and the potential of the proposed procedure for use in conjunction with large-scale finite element modeling of composite structures is discussed. It is shown that the use of the shear correction factors calculated by this procedure extends the range of the validity of the first-order shear deformation theory, used in the first phase of the procedure, to fairly thick multilayered plates with the h/L1 ratio of the order of 0.3.

Noor, Ahmed K.↗

NASA NTRS1989

The proximity of hotspots to convergent and divergent plate boundaries

An analysis of four different hotspot distributions, ranging from Morgan's (1972) original list of 19 to Vogt's (1981) list of 117 reveals that the hotspots are preferentially located near divergent plate boundaries. The probability of this proximity occurring by chance alone is quite remote, less than 0.01 for all four hotspot distributions. The same analysis also reveals that the hotspots are preferentially excluded from regions near convergent plate boundaries. The probability of this exclusion occurring by chance alone is 0.1 or less for three out of the four distributions examined. We interpret this behavior as being a consequence of the effects of large scale convective circulation on ascending mantle plumes. Mantle thermal plumes, the most probable source of hotspots, arise from instabilities in a basal thermal boundary layer. Plumes are suppressed from regions beneath convergent boundaries by descending flow and are entrained into the upwelling flow beneath spreading centers. Plate-scale convective circulation driven by subduction may also advect mantle thermal plumes toward spreading centers.

Weinstein, Stuart A.↗

NASA NTRS1990

Multiple-Inlet/Single-Outlet Orifice Plate

Orifice plate for control of flow has multiple slanted inlets leading to single outlet. Multiple-inlet/single-outlet orifice less susceptible to blockage than single hole drilled through plate perpendicular to its surface. Easily calibrated for various flow rates and fits in place of simple orifice plate with no other modifications.

Godown, Robert L.↗

NASA NTRS1990

On the instability of hypersonic flow past a flat plate

The instability of hypersonic boundary-layer flows over flat plates is considered. The viscosity of the fluid is taken to be governed by Sutherland's law, which gives a much more accurate representation of the temperature dependence of fluid viscosity at hypersonic speeds than Chapman's approximate linear law; although at lower speeds the temperature variation of the mean state is less pronounced so that the Chapman law can be used with some confidence. Attention is focussed on the so-called (vorticity) mode of instability of the viscous hypersonic boundary layer. This is thought to be the fastest growing inviscid disturbance at hypersonic speeds; it is also believed to have an asymptotically larger growth rate than any viscous or centrifugal instability. As a starting point the instability of the hypersonic boundary layer which exists far downstream from the leading edge of the plate is investigated. In this regime the shock that is attached to the leading edge of the plate plays no role, so that the basic boundary layer is non-interactive. It is shown that the vorticity mode of instability of this flow operates on a significantly different lengthscale than that obtained if a Chapman viscosity law is assumed. In particular, it is found that the growth rate predicted by a linear viscosity law overestimates the size of the growth rate by O(M(exp 2). Next, the development of the vorticity mode as the wavenumber decreases is described, and it is shown that acoustic modes emerge when the wavenumber has decreased from it's O(1) initial value to O(M (exp -3/2). Finally, the inviscid instability of the boundary layer near the leading edge in the interaction zone is discussed and particular attention is focussed on the strong interaction region which occurs sufficiently close to the leading edge. It is found that the vorticity mode in this regime is again unstable, and that it is concentrated in the transition layer at the edge of the boundary layer where the temperature adjusts from its large, O(M(exp 2), value in the viscous boundary layer, to its O(1) free stream value. The existence of the shock indirectly, but significantly, influences the instability problem by modifying the basic flow structure in this layer.

Blackaby, Nicholas↗

NASA NTRS1990

Experiment K-6-06. Morphometric and EM analyses of tibial epiphyseal plates from Cosmos 1887 rats

Light and electron microscopy studies were carried out on decalcified tibial epiphyseal plates of rats flown aboard Cosmos 1887 (12.5d flight plus 53.5h recovery). Analysis of variance showed that the proliferative zone of flight animals was significantly higher than that of synchronous controls, while the hypertrophic/calcification zone was significantly reduced. Flight animals had more cells than synchronous controls in the proliferative zone, and less in the hypertrophic/calcification region. The total number of cells, however, was significantly higher in flight animals. No differences were found for perimeter or shape factor of growth plates, but area was significantly lower in flight animals in comparison to synchronous controls. Collagen fibrils in flight animals were shorter and wider than in synchronous controls. The time required for a cell to cycle through the growth plate is 2 to 3 days, so most of the cells and matrix present were formed after the animals had returned to 1 g, and probably represent stages of recovery from microgravity exposure, which in itself is an interesting question.

Duke, P. J.↗

NASA NTRS1989

Surface crack problems in plates

The mode I crack problem in plates under membrane loading and bending is reconsidered. The purpose is to examine certain analytical features of the problem further and to provide some new results. The formulation and the results given by the classical and the Reissner plate theories for through and part-through cracks are compared. For surface cracks the three-dimensional finite element solution is used as the basis of comparison. The solution is obtained and results are given for the crack/contact problem in a plate with a through crack under pure bending and for the crack interaction problem. Also, a procedure is developed to treat the problem of subcritical crack growth and to trace the evolution of the propagating crack.

Joseph, P. F.↗

NASA NTRS1990

Active control of sound transmission/radiation from elastic plates by vibration inputs. I - Analysis

Active control of sound radiation from vibrating plates by oscillating forces applied directly to the structure is analytically studied. The model consists of a plane acoustic wave incident on a clamped elastic circular thin plate. Control is achieved by point forces, and quadratic optimization is used to calculate the optimal control gains necessary to minimize a cost function proportional to the radiated acoustic power (the transmitted field). The results show that global attenuation of broadband radiated sound levels for low to mid-range frequencies can be achieved with one or two control forces, irrespective of whether the system is on or off resonance. The efficiency of the control strategy is demonstrated to be related to the nature of the coupling between the plate modes of response and the radiated field.

Fuller, C. R.↗

NASA NTRS1989

Interference effects on the hypersonic, rarefied flow about a flat plate

The Direct Simulatiaon Monte Carlo method is used to study the hypersonic, rarefied flow interference effects on a flat plate caused by nearby surfaces. Calculations focus on shock-boundary-layer and shock-lip interactions in hypersonic inlets. Results are presented for geometries consisting of a flat plate with different leading-edge shapes over a flat lower wall and a blunt-edge flat plate over a 5-degree wedge. The problems simulated correspond to a typical entry flight condition of 7.5 km/s at altitudes of 75 to 90 km. The results show increases in predicted local heating rates for shock-boundary-layer and shock-lip interactions that are quantitatively similar to those observed experimentally at much higher densities.

Wilmoth, Richard G.↗

NASA NTRS1990

Comparison of equivalent plate and finite element analysis of a realistic aircraft structural configuration

This paper presents a comparison study to assess how well a realistic aircraft structure can be represented with an equivalent plate model. A wing box and full wing structure of a high-speed civil transport aircraft configuration are analyzed. Static and vibration results from the equivalent plate analysis are compared with results from a finite element model. The results from these comparisons show that, for the simpler wing box models, the static displacements and first vibration frequency agree to within 1.5 percent. The full wing models only agree to within 10 percent, for both models, the higher frequencies vary by as much as 26 percent. These differences are due to inadequate refinement of the equivalent plate model.

Kao, Pi-Jen↗

NASA NTRS1991

Analysis of a thick dichroic plate with rectangular holes at arbitrary angles of incidence

A thick dichroic plate that is transparent to one frequency band while at the same time reflective to other frequencies is needed for high power transmission in the Deep Space Network. Software based on the method of moments was developed to design a thick dichroic plate with rectangular holes. A test dichroic plate was fabricated, and an experiment was performed to verify the computer code. Good agreement was found between theory and experiment.

Chen, J. C.↗

NASA NTRS1990

Theoretical hypervelocity ballistic limit for single or double plates using nonlinear modal analysis

The original research on the use on nonlinear vibration technique to solve for the hypervelocity ballistic limit for double plates is examined. Such structure is commonly found in typical Space Station design where the incoming space or man-made debris would be fragmented upon hitting the outer plate (shield) and the subsequent impact on the main wall would result in a much reduced damge of the space station or spacecraft. The existing few theoretical impact equations do not agree well with each other. The existing computer code bumper used at NASA-Johnson Space Center appears to predict an unconservative ballistic limit when compared with experimental data where the velocity ranges from 3 km/s to 8 km/s. Such unconservative prediction is unacceptable from a practical safe design point of view. The bumper code is based on Wilkinson's (1968) paper and his equations have not been improved nor modified even though they are viewed with suspicion due to lack of agreement with experiments. To make matters worse, there is not another theory which is better than Wilkinson's equation and the designers are forced to use purely empirical Nysmith (1969) or semiempirical equations developed by Cour-Palais in 1969. The Cour-Palais equations were later modified empirically in 1989. The purpose of the present investigation is to examine the many assumptions of the Wilkinson equation. An attempt is made to present design charts based on the modified-Wilkinson equation so that the designer can get a feel of the ranges of the parameters which are of interest and discard a huge range of parameters, thus, significantly reducing the number of test shots required. The analysis is based on a solution of the governing nonlinear differential equations for a plate, assuming axisymmetric behavior using polar coordinates.

Hui, David↗

NASA NTRS1991

Report of the panel on plate motion and deformation, section 2

Given here is a panel report on the goals and objectives, requirements and recommendations for the investigation of plate motion and deformation. The goals are to refine our knowledge of plate motions, study regional and local deformation, and contribute to the solution of important societal problems. The requirements include basic space-positioning measurements, the use of global and regional data sets obtained with space-based techniques, topographic and geoid data to help characterize the internal processes that shape the planet, gravity data to study the density structure at depth and help determine the driving mechanisms for plate tectonics, and satellite images to map lithology, structure and morphology. The most important recommendation of the panel is for the implementation of a world-wide space-geodetic fiducial network to provide a systematic and uniform measure of global strain.

Bock, Yehuda↗