Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE DEPENDENCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Simultaneous measurement of pressure evolution of crystal structure and superconductivity in FeSe[subscript 0.92] using designer diamonds

Simultaneous high-pressure X-ray diffraction and electrical resistance measurements have been carried out on a PbO-type {alpha}-FeSe{sub 0.92} compound to a pressure of 44 GPa and temperatures down to 4 K using designer diamond anvils at synchrotron source. A ambient temperature, a structural phase transition from a tetragonal (P4/nmm) phase to an orthorhombic (Pbnm) phase is observed at 11 GPa and the Pbnm phase persists up to 74 GPa. The superconducting transition temperature (T{sub c}) increases rapidly with pressure reaching a maximum of {approx}28 K at {approx}6 GPa and decreases at higher pressures, disappearing completely at 14.6 GPa. Simultaneous pressure-dependent X-ray diffraction and resistance measurements at low temperatures show superconductivity only in a low-pressure orthorhombic (Cmma) phase of the {alpha}-FeSe{sub 0.92}. Upon increasing pressure at 10 K near T{sub c}, crystalline phases change from a mixture of orthorhombic (Cmma) and hexagonal (P63/mmc) phases to a high-pressure orthorhombic (Pbnm) phase near 6.4 GPa where T{sub c} is maximum.

Uhoya, Walter↗
NASA NTRS1981

Effect of surface roughness on elastohydrodynamic line contact

A numerical solution of an elastohydrodynamic lubrication (EHL) contact between two long rough surface cylinders is obtained. A simultaneous solution of an elasticity equation and the Reynolds equation for two partially lubricated rough surfaces is used to obtain a theoretical solution of pressure distribution, elastohydrodynamic load and film thicknesses for given speeds. A theoretical solution is also found for lubricants with pressure dependent viscosity, material properties of cylinders, and surface roughness parameters. Elastic deformation is found from hydrodynamic and contact pressure using plane strain analysis, and results indicate that for a constant central film thickness, increasing the surface roughness decreases the EHL load and there is little variation in minimum film thicknesses as the surface roughness is increased.

Majumdar, B. C.↗
NASA NTRS1986

Kinetics and mechanism of the IO + IO reaction

The flash photolysis-absorption technique has been used to measure the rate constant for the reaction IO + IO over the temperature range 250-373 K and pressure range 20-700 torr of N2. The rate constant for the overall reaction was found to be independent of pressure and equal to 1.73 x 10 to the -12th exp (1020 + or - 200)/T cu cm/molecule s. Branching ratios for the reaction channels forming 2I + O2, I2 + O2, and I2O2, were found to be pressure dependent, with the I2 channel accounting for less than 5 percent of the total reaction over the observed pressure range. A stable reaction product was observed between 230 and 300 nm which was formed on a long time scale compared to IO disappearance. The rate constant for the reaction I + O3 + yields to IO + O2 was measured at 298 K and found to be (9.5 + or - 1.5) x 10 to the -13th cu cm/molecule s.

Sander, S. P.↗
NASA NTRS1991

Characteristics of a high pressure gas proportional counter filled with xenon

The characteristics of a conventional cylindrical geometry proportional counter filled with high pressure xenon gas up to 10 atm. were fundamentally investigated for use as a detector in hard X-ray astronomy. With a 2 percent methane gas mixture the energy resolutions at 10 atm. were 9.8 percent and 7.3 percent for 22 keV and 60 keV X-rays, respectively. From calculations of the Townsend ionization coefficient, it is shown that proportional counters at high pressure operate at weaker reduced electric field than low pressure counters. The characteristics of a parallel grid proportional counter at low pressure showed similar pressure dependence. It is suggested that this is the fundamental reason for the degradation of resolution observed with increasing pressure.

Sakurai, H.↗
NASA NTRS2004

Thermal-Structural Optimization of Integrated Cryogenic Propellant Tank Concepts for a Reusable Launch Vehicle

A next generation reusable launch vehicle (RLV) will require thermally efficient and light-weight cryogenic propellant tank structures. Since these tanks will be weight-critical, analytical tools must be developed to aid in sizing the thickness of insulation layers and structural geometry for optimal performance. Finite element method (FEM) models of the tank and insulation layers were created to analyze the thermal performance of the cryogenic insulation layer and thermal protection system (TPS) of the tanks. The thermal conditions of ground-hold and re-entry/soak-through for a typical RLV mission were used in the thermal sizing study. A general-purpose nonlinear FEM analysis code, capable of using temperature and pressure dependent material properties, was used as the thermal analysis code. Mechanical loads from ground handling and proof-pressure testing were used to size the structural geometry of an aluminum cryogenic tank wall. Nonlinear deterministic optimization and reliability optimization techniques were the analytical tools used to size the geometry of the isogrid stiffeners and thickness of the skin. The results from the sizing study indicate that a commercial FEM code can be used for thermal analyses to size the insulation thicknesses where the temperature and pressure were varied. The results from the structural sizing study show that using combined deterministic and reliability optimization techniques can obtain alternate and lighter designs than the designs obtained from deterministic optimization methods alone.

Johnson, Theodore F.↗
DOE OSTI2019

High-pressure, high-temperature hollow sphere acoustic pressure sensor

A pressure sensor and a method of measuring pressure with the pressure sensor, based on measuring the effect of pressure loads on the acoustic resonance mode frequencies of a spherical core (e.g., a hollow sphere). The pressure sensor includes a transmitter configured to transmit vibrational signals to a sphere, and a receiver on the opposite side of the spherical core that is configured to receive vibrational signals from the spherical core. According to the method of measuring pressure with this sensor, the spherical core exhibits a pressure-dependent resonance response that can be monitored utilizing a frequency response technique. Peak shifts observed under an unknown pressure load can be compared to a calibration of the spherical core under a series of known pressure loads to thereby determine the unknown pressure. The pressure sensor and method may be operated in real-time at very high temperatures and pressure, and may be used in borehole applications and in aggressive media.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1984

Pressure and temperature dependence of the reaction NO2 + NO3 + M yields N2O5 + M

The pressure and temperature dependences of the reaction NO2 + NO3 + M which yields N2O5 + M are investigated by using the flash photolysis/visible absorption technique in which the pseudo-first-order decay of NO3 is monitored as a function of total pressure (20-700 torr), diluent gas (M = He and N2), and temperature (236-358 K). The reaction is found to be in the falloff region in the 20-700 torr pressure range with collision efficiencies increasing in the order He less than N2. Falloff parameters are obtained by fitting the experimental data to the falloff equation of Troe and co-workers. The expression for k1(N2 concentration, T) is obtained and compared with the evaluations presented in the NASA (DeMore, 1983) and CODATA (Baulch et al., 1982) reviews of kinetic data for atmospheric chemistry. Both evaluations are based on N2O5 thermal decomposition data coupled with estimates of the equilibrium constant. The significance of the reactions for atmospheric chemistry rests not only on their rates but on the extent to which they result in a permanent sink for NOX.

Kircher, C. C.↗
DOE OSTI2016

Competition of superconductivity with the structural transition in M o 3 S b 7

Prior to the superconducting transition at T c ≈ 2.3 K, Mo 3 Sb 7 undergoes a symmetry-lowering, cubic-to-tetragonal structural transition at T s = 53 K. In this paper, we have monitored the pressure dependence of these two transitions by measuring the resistivity of Mo 3 Sb 7 single crystals under various hydrostatic pressures up to 15 GPa. The application of external pressure enhances T c but suppresses T s until P c ≈ 10 GPa, above which a pressure-induced first order structural transition takes place and is manifested by the phase coexistence in the pressure range 8 ≤ P ≤ 12 GPa. The cubic phase above 12 GPa is also found to be superconducting with a higher T c ≈ 6 K that decreases slightly with further increasing pressure. The variations with pressure of T c and T s satisfy the Bilbro-McMillan equation, i.e. T c n T s 1-n = constant, thus suggesting the competition of superconductivity with the structural transition that has been proposed to be accompanied with a spin-gap formation at T s . Finally, this scenario is supported by our first-principles calculations which imply the plausible importance of magnetism that competes with the superconductivity in Mo 3 Sb 7 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1986

Tropospheric HO determination by FAGE

In the detection of tropospheric HO by laser excited fluorescence, and alternative air-sampling method, named FAGE (Fluorescence Assay with Gas Expansion) was introduced. Here the air is expanded through a nozzle prior to excitation, in order to improve the ratio of the HO signal to the scattered, fluorescent, and photolytic backgrounds. The improvement comes from the differing pressure dependence of the intensities of these four terms, as well as the distinguishability of their temporal waveforms at low pressures when excited by a pulsed laser. HO has been excited by a YAG/dye laser. Other lasers and pumping paths may perform as well or better in this method. With FAGE, chemical modulation of the HO signal was achieved by hydrocarbon addition to the nozzle flow, converting photolytic HO from an interference to a background. Chemical calibration of the instrumental response to external HO was also achieved, by hydrocarbon decay, at HO concentrations within the ambient range.

Hard, T. M.↗
NASA NTRS2003

Hydrostatic Stress Effect on the Yield Behavior of Inconel 100

Classical metal plasticity theory assumes that hydrostatic stress has negligible effect on the yield and postyield behavior of metals. Recent reexaminations of classical theory have revealed a significant effect of hydrostatic stress on the yield behavior of various geometries. Fatigue tests and nonlinear finite element analyses (FEA) of Inconel 100 (IN100) equal-arm bend specimens and new monotonic tests and nonlinear finite element analyses of IN100 smooth tension, smooth compression, and double-edge notch tension (DENT) test specimens have revealed the effect of internal hydrostatic tensile stresses on yielding. Nonlinear FEA using the von Mises (yielding is independent of hydrostatic stress) and the Drucker-Prager (yielding is linearly dependent on hydrostatic stress) yield functions were performed. A new FEA constitutive model was developed that incorporates a pressure-dependent yield function with combined multilinear kinematic and multilinear isotropic hardening using the ABAQUS user subroutine (UMAT) utility. In all monotonic tensile test cases, the von Mises constitutive model, overestimated the load for a given displacement or strain. Considering the failure displacements or strains for the DENT specimen, the Drucker-Prager FEM s predicted loads that were approximately 3% lower than the von Mises values. For the failure loads, the Drucker Prager FEM s predicted strains that were up to 35% greater than the von Mises values. Both the Drucker-Prager model and the von Mises model performed equally-well in simulating the equal-arm bend fatigue test.

Allen, Phillip A.↗
NASA NTRS2014

Propagation of Radiosonde Pressure Sensor Errors to Ozonesonde Measurements

Several previous studies highlight pressure (or equivalently, pressure altitude) discrepancies between the radiosonde pressure sensor and that derived from a GPS flown with the radiosonde. The offsets vary during the ascent both in absolute and percent pressure differences. To investigate this problem further, a total of 731 radiosonde-ozonesonde launches from the Southern Hemisphere subtropics to Northern mid-latitudes are considered, with launches between 2005 - 2013 from both longer-term and campaign-based intensive stations. Five series of radiosondes from two manufacturers (International Met Systems: iMet, iMet-P, iMet-S, and Vaisala: RS80-15N and RS92-SGP) are analyzed to determine the magnitude of the pressure offset. Additionally, electrochemical concentration cell (ECC) ozonesondes from three manufacturers (Science Pump Corporation; SPC and ENSCI-Droplet Measurement Technologies; DMT) are analyzed to quantify the effects these offsets have on the calculation of ECC ozone (O3) mixing ratio profiles (O3MR) from the ozonesonde-measured partial pressure. Approximately half of all offsets are 0.6 hPa in the free troposphere, with nearly a third 1.0 hPa at 26 km, where the 1.0 hPa error represents 5 persent of the total atmospheric pressure. Pressure offsets have negligible effects on O3MR below 20 km (96 percent of launches lie within 5 percent O3MR error at 20 km). Ozone mixing ratio errors above 10 hPa (30 km), can approach greater than 10 percent ( 25 percent of launches that reach 30 km exceed this threshold). These errors cause disagreement between the integrated ozonesonde-only column O3 from the GPS and radiosonde pressure profile by an average of +6.5 DU. Comparisons of total column O3 between the GPS and radiosonde pressure profiles yield average differences of +1.1 DU when the O3 is integrated to burst with addition of the McPeters and Labow (2012) above-burst O3 column climatology. Total column differences are reduced to an average of -0.5 DU when the O3 profile is integrated to 10 hPa with subsequent addition of the O3 climatology above 10 hPa. The RS92 radiosondes are superior in performance compared to other radiosondes, with average 26 km errors of -0.12 hPa or +0.61 percent O3MR error. iMet-P radiosondes had average 26 km errors of -1.95 hPa or +8.75 percent O3MR error. Based on our analysis, we suggest that ozonesondes always be coupled with a GPS-enabled radiosonde and that pressure-dependent variables, such as O3MR, be recalculated-reprocessed using the GPS-measured altitude, especially when 26 km pressure offsets exceed 1.0 hPa 5 percent.

pressure measurements↗
NASA NTRS2026

Development and Validation of a High-Vacuum Thermal Conductivity Testbed for Aerospace Interface Materials

Thermal Interface Materials (TIMs) are critical components in spacecraft thermal management systems, where thermal performance is strongly influenced by vacuum conditions, interface contact resistance, and layered metallic joint behavior. However, manufacturer-reported thermal conductivity values are often derived under idealized conditions and may not accurately represent performance within operational aerospace applications. To address this limitation, the Testbed for Advanced Interface Materials in Vacuum (TAIMV) was developed as a modular vacuum-compatible thermal conductivity characterization platform capable of evaluating aerospace-relevant TIM configurations under both ambient and high-vacuum environments. The testbed was derived from the ASTM C1044-16 guarded hot plate methodology and incorporates interchangeable layers of stainless steel coupon geometries, independently controlled main and guard heaters, embedded resistance temperature detectors (RTDs), thermocouples, multi-layer insulation (MLI), and a temperature-controlled cold plate to characterize through-thickness thermal gradients across layered interfaces. In the current configuration, interface compression is limited to the nominal contact pressure generated by the experimental stack assembly. Initial experimental campaigns were conducted at ambient pressure and below 1×10-5 torr for vacuum cases using multiple interface materials including Braycote 601EF and Krytox-based greases across a range of thermal operating conditions. In parallel, a coupled numerical Python thermal model was developed to predict temperature distribution throughout the stack while accounting for conduction, radiation, and parasitic heat transfer pathways and effective interface resistance effects. Experimental measurements and numerical predictions showed consistent thermal trends across multiple operating conditions and environmental states. Results also revealed measurable differences between ambient and vacuum thermal behavior, demonstrating the importance of interface resistance, parasitic heat transfer mechanisms, and stack geometry in determining effective thermal performance within layered thermal interfaces. The presented work establishes a foundation for future thermal model correlation efforts and expanded characterization of aerospace thermal interface materials under representative environmental conditions. Future work will focus on the integration of a load cell system to enable controlled pressure-dependent characterization of thermal interface materials under compressive loading. This capability will allow investigation of the influence of contact pressure on effective thermal conductivity, interface resistance, and thermal performance within layered aerospace thermal interfaces under representative operational conditions.

Thermal Development Testing↗
DOE OSTI2026

The impact of metastability on the high-pressure behavior of cerium

The structures adopted by solids under pressure are often assumed to reflect thermodynamic equilibrium, yet in many materials phase selection is strongly influenced by kinetic pathways and microstructural inheritance. Elemental cerium (Ce) exemplifies this challenge, with decades of conflicting reports describing different high-pressure crystal structures emerging under nominally identical conditions. Here we use neutron diffraction from large ( ~ 60 mm 3 ) sample volumes to follow the structural evolution in ultra-high-purity Ce during controlled pressure-temperature cycling between 85 and 295 K and up to 8 GPa. We find that the crystal structure formed at high pressure depends on the compression pathway: slow compression ( ~ 0.25 GPa hr −1 ) at room temperature favors an orthorhombic phase (α'), whereas slow ( ~ 0.25 GPa hr −1 ) and also moderately faster ( ~ 0.5 GPa hr −1 ) compression at low temperature stabilizes a pure monoclinic phase (α"). The low-temperature phase persists metastably over a wide temperature range but transforms irreversibly upon heating above ~ 280 K, or modest pressure cycling. Remarkably, the lower-pressure γ phase remains trapped far beyond the expected stability field, persisting to the highest pressures studied. These observations show that phase selection in Ce is governed by kinetics and microstructural memory rather than equilibrium thermodynamics or sample morphology alone, establishing path dependence as a defining feature of its high-pressure behavior.

Ridley, Christopher J. [Oak Ridge National Laborat↗
DOE OSTI2024

Comparison of Americium(III) and Neodymium(III) Monothiophosphate Complexes

Mixed-donor ligands, such as those containing a combination of O/N or O/S, have been studied extensively for the selective extraction of trivalent actinides, especially Am 3+ and Cm3+, from lanthanides during the recycling of used nuclear fuel. Oxygen/sulfur donor ligand combinations also result from the hydrolytic and/or radiolytic degradation of dithiophosphates, such as the Cyanex® class of extractants, that are initially converted to monothiophosphates. To understand potential differences between the binding of such degraded ligands to Nd 3+ and Am 3+ , the monothiophosphate complexes [M(OPS(OEt) 2 ) 5 (H 2 O) 2 ] 2- (M 3+ = Nd 3+ , Am 3+ ) were prepared and characterized by single crystal X-ray diffraction and optical spectroscopy and studied as a function of pressure up ca. 14 GPa using diamond-anvil techniques. Although Nd 3+ and Am 3+ have nearly identical eight-coordinated ionic radii, these structures reveal that while the M-O bond distances in these complexes are nearly equal that the M-S distances are statistically different. Moreover, for [Nd(OPS(OEt) 2 ) 5 (H 2 O) 2 ] 2- , the hypersensitive 4 I 9/2 → 4 G 5 / 2 transition shifts as a function of pressure by -11 cm -1 /GPa. Whereas for [Am(OPS(OEt) 2 ) 5 (H 2 O) 2 ] 2- , the 7 F 0 → 7 F 6 transition shows a slightly stronger pressure dependence with a shift of -13 cm -1 /GPa and also exhibits broadening of the 5f →5f transitions at high pressures. This data likely indicates an increased involvement of the 5f orbitals in bonding to Am 3+ relative to that of Nd 3+ in these complexes.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Access and Capture of Layered Double Perovskite Polytypic Phase through High-Pressure Engineering

Engineering halide perovskites through external pressure is as an effective means to tune the crystal structure, thus optoelectronic properties of the material. In this work, we studied the structural and optical property evolutions of Cs 4 M II Bi 2 Cl 12 (M II : Cd, Cd 0.8 Mn 0.2 , Mn) layered double perovskite (LDP) crystalline powders under high pressure. A novel polytypic phase transition was observed featuring lateral interlayer sliding of the Bi–M II –Bi trilayer units, resulting in a new LDP-12R phase. Importantly, this high-pressure induced LDP-12R crystal phase can be preserved after complete decompression and captured at ambient conditions. Moreover, the LDP samples showed a pressure-dependent photoluminescence property. Finally, our findings exemplified a new perovskite polytype that can be accessed and captured through high-pressure processing, advocating the uniqueness of LDP materials with soft and transformable crystal lattices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Wisconsin In Situ Penning (WISP) gauge: A versatile neutral pressure gauge to measure partial pressures in strong magnetic fields

A new type of in-vessel Penning gauge, the Wisconsin In Situ Penning (WISP) gauge, has been developed and successfully operated in the Wendelstein 7-X (W7-X) island divertor baffle and vacuum vessel. The capacity of the quantitative measurements of the neutral reservoir for light impurities, in particular, helium, is important for tokamaks as well as stellarator divertors in order to avoid fuel dilution and radiative energy loss. Penning gauges assisted by spectroscopy are a powerful tool to obtain the total neutral pressure as well as fractional neutral pressures of specific impurities. The WISP gauge is a miniaturized Penning gauge arrangement, which exploits the ambient magnetic field of magnetic confinement fusion experiments to establish the Penning discharge. Then, in situ spectroscopy is conducted to separate the fractional neutral pressures of hydrogen, helium, and possibly also other impurities. The WISP probe head was qualified using the magnetic field of the Magnetized Dusty Plasma Experiment at Auburn University between 0.25 T and 3.5 T [E. Thomas et al ., J. Plasma Phys. 81, 345810206 (2015)]. The in-depth quantitative evaluation for hydrogen and helium will be shown as well as an exploration of nitrogen, argon, and neon. A power law scaling between current I and pressure p, I = f (Gas,V) p n⁽Gas, B⁾ , was shown. The factor f is gas and anode potential dependent, while n is gas and magnetic field strength dependent. Pressure measurements from 0.1 mbar and down to 1 × 10 -5 mbar were achieved, demonstrating a reliable operating range for relevant pressure levels in the divertor and main vessel regions in current and future fusion devices, with a time resolution of up to 1 kHz. The lowest achievable pressure measurement increases with an increase in B and can be shifted with the anode potential V . At W7-X, the WISP probe head was mounted on an immersion tube setup that passes through the cryostat and places the probe head close to the plasma. Two probe heads were positioned in different divertor pump gaps, top and bottom, and one close to the plasma on the midplane in one module. The gauges were in situ calibrated together with the ASDEX pressure gauges [G. Haas and H.-S. Bosch, Vacuum 51, 39 (1998)]. Data were taken during the entire operation phase 1.2b, and measurements were coherent with other neutral gas pressure gauges. For the spectroscopic partial pressure measurements, channels of a spectroscopic detection system based on photo-multipliers, a so-called filterscope [R. J. Colchin et al ., Rev. Sci. Instrum. 74, 2068 (2003)], provided by the Oak Ridge National Lab were used.

47 OTHER INSTRUMENTATION↗