SEARCH · Search NASA

Results for “Pressure transducers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Study of noise and inflow distortion sources in the NASA QF-1B fan using measured blade and vane pressures

Pressure transducers were installed on the blades and vanes of QF-1B, a transonic-tip-speed fan from the NASA Quiet Fan Program which was tested on the outdoor quiet fan test facility at NASA-Lewis. Signals from the transducers and from far field microphones were analyzed to determine sources of nonuniform inflow and noise. The nonuniform inflow was mostly unsteady with roughly equal contributions from atmospheric turbulence and rig interference. The rig interference was largest at the bottom and appeared to be generated by the support structure which was located behind the inlet lip under the fan. Interaction of this inflow distortion was the dominant source of noise at 1, 2, and 3 times blade passing frequency (BPF) at 60, 70, and 80 percent of design speed. At 90 percent speed, noise at BPF was dominated by the steady rotor field. A broadband spectrum peak centered at about 2.2 times BPF was identified as rotor/stator interaction stemming from a high frequency rotor exit flow component. The remaining broadband energy from 0.3 to 3.5 times BPF was attributed to the better known type of rotor/stator interaction associated with rotor wake turbulence.

Hanson, D. B.↗

NASA NTRS1977

Expansion tunnel performance with and without an electromagnetically opened tertiary diaphragm

A study was conducted to examine the effect of synchronization of an electromagnetically opened tertiary diaphragm with flow arrival at the diaphragm on the pitot pressure measured at the test section of an expansion tunnel. The effect of tertiary diaphragm pressure ratio (ratio of initial nozzle pressure to quiescent acceleration section pressure) on the pitot pressure time history is also determined. The inadequacy of a pressure transducer protection arrangement used in previous expansion tube and expansion tunnel tests was revealed.

Miller, C. G.↗

NASA NTRS1978

Detection of boundary-layer transitions in wind tunnels

Accelerometer replaces stethoscope in technique for detection of laminar-to-turbulent boundary-layer transitions on wind-tunnel models. Technique allows measurements above or below atmospheric pressure because human operator is not required within tunnel. Data may be taken from accelerometer, and pressure transducer simultaneously, and delivered to systems for analysis.

Wood, W. R.↗

NASA NTRS1977

Results of an investigation of the acoustic and vibrational environment of a full scale space shuttle orbiter structural test panel with simulated TPS in the Ames unitary plan wind tunnel, model 81-0, test OS8A and B

Results of tests OS8A and B and pertinent test and model information are presented. The test was conducted in two parts. Test OS8A was performed in the NASA/ARC unitary 11-foot section and OS8B was conducted in the NASA/ARC unitary 9 x 7 tunnel. Test objectives were to investigate thermal protection system (TPS) tile sensitivity to extreme pressure gradients and vibration and to define the TPS aerodynamic environment. The model utilized for OS8 was a full-scale representation of a portion of the space shuttle orbiter lower wing carry-through structure forward of the aft tank strut and propellant lines. Thermal protection tiles were simulated on the model. The model was instrumented with static pressure orifices, accelerometers, and dynamic pressure transducers (Kulites). A total rake was utilized to obtain boundary layer surveys.

Kingsland, R. B.↗

NASA NTRS1978

Investigation of the unsteady pressure distribution on the blades of an axial flow fan

The unsteady response of a stator blade caused by the interaction of the stator with the wakes of an upstream rotor was investigated. Unsteady pressure distributions were measured using a blade instrumented with a series miniature pressure transducers. The influence of several geometrical and flow parameters - rotor/stator spacing, stator solidity and stator incidence angle - were studied to determine the unsteady response of the stator to these parameters. A major influence on the stator unsteady response is due to the stator solidity. At high solidities the blade-to-blade interference has a larger contribution. While the range of rotor/stator spacings investigated had a minor influence, the effect of stator incidence angle is significant. The data indicate the existence of an optimum positive incidence which minimizes the unsteady response.

Henderson, R. E.↗

NASA NTRS1978

A rotor-mounted digital instrumentation system for helicopter blade flight research measurements

A rotor mounted flight instrumentation system developed for helicopter rotor blade research is described. The system utilizes high speed digital techniques to acquire research data from miniature pressure transducers on advanced rotor airfoils which are flight tested on an AH-1G helicopter. The system employs microelectronic pulse code modulation (PCM) multiplexer digitizer stations located remotely on the blade and in a hub mounted metal canister. As many as 25 sensors can be remotely digitized by a 2.5 mm thick electronics package mounted on the blade near the tip to reduce blade wiring. The electronics contained in the canister digitizes up to 16 sensors, formats these data with serial PCM data from the remote stations, and transmits the data from the canister which is above the plane of the rotor. Data are transmitted over an RF link to the ground for real time monitoring and to the helicopter fuselage for tape recording. The complete system is powered by batteries located in the canister and requires no slip rings on the rotor shaft.

Knight, V. H., Jr.↗

NASA NTRS1978

Instrumentation for propulsion systems development

Various types of instrumentation for the development of propulsion systems are discussed. For the steady-state measurement of local temperature, pressure and flow velocity in gases the devices include: a multielement probe, calibrated thermocouple probes, thermocouple probes designed for low gas velocities, pressure measuring devices for high-speed rotors, and instruments for data pickup from rotating members. For the dynamic measurements of the same factors attention is given to 2-mm diameter pressure transducers, flush-diaphragm transducers, resistance thermometers or thermocouples, and miniature transducers for velocity measurements. Instruments for compressor and turbine-blade instrumentation are described with reference to a pyrometer for mapping turbine-blade surface temperature, a capacitance method for making rotor clearance measurements, and optical detection procedures for blade vibration amplitude.

Warshawsky, I.↗

NASA NTRS1978

New NASA-Ames wind-tunnel techniques for studying airplane spin and two-dimensional unsteady aerodynamics

Two new wind tunnel test apparatuses were developed at NASA-Ames Research Center. The first is a rotary-balance apparatus to be used in the Ames 12-Foot Pressure Tunnel for investigating the effects of Reynolds number, spin rate, and angle of attack on the aerodynamics of fighter and general aviation aircraft in a steady spin motion. The second apparatus provides capability for oscillating a large two dimensional wing (0.5 m chord, 1.35 m span) instrumented with steady and unsteady pressure transducers in the Ames 11 x 11 ft. Transonic Wind Tunnel. A complete description of both apparatuses, their capabilities, and some typical wind tunnel results are presented.

Malcolm, G. N.↗

NASA NTRS1979

Some steady and oscillating airfoil test results, including the effects of sweep, from the tunnel spanning wing

A large scale tunnel spanning wing was built and tested. The model can be operated as either a swept or unswept wing and can be tested in steady state or oscillated sinusoidally in pitch about its quarter chord. Data is taken at mid-span with an internal 6-component balance and is also obtained from miniature pressure transducers distributed near the center span region. A description is given of the system and a brief discussion of some of the steady and unsteady results obtained to date. These are the steady load behavior to Mach numbers of approximately 1.1 and unsteady loads, including drag, at a reduced frequency of approximately 0.1.

Carta, F. O.↗

NASA NTRS1978

A new approach to helicopter rotor blade research instrumentation

A rotor-blade-mounted telemetry instrumentation system developed and used in flight tests by the NASA/Langley Research Center is described. The system uses high-speed digital techniques to acquire research data from miniature pressure transducers on advanced rotor airfoils which are flight tested using an AH-1G helicopter. The system employs microelectronic PCM multiplexer-digitizer stations located remotely on the blade and in a hub-mounted metal canister. The electronics contained in the canister digitizes up to 16 sensors, formats this data with serial PCM data from the remote stations, and transmits the data from the canister which is above the plane of the rotor. Data is transmitted over an RF link to the ground for real-time monitoring and to the helicopter fuselage for tape recording.

Knight, V. H., Jr.↗

NASA NTRS1980

Additional flow quality measurements in the Langley Research Center 8-Foot Transonic Pressure Tunnel

Additional tests were conducted to further define the disturbance characteristics of the Langley 8-Foot Transonic Pressure Tunnel. Measurements were made in the settling chamber with hot wire probes and in the test section with pressure transducers when various methods were used to choke the flow. In addition to presenting rms values measured at various locations and tunnel condition, autocorrelations and cross correlation data are also presented.

Brooks, J. D.↗

NASA NTRS1980

Techniques for aerodynamic and turbulence measurements in turbomachinery rotors

Nonoptical techniques currently used to measure flows in turbomachine rotors are reviewed, with particular reference to the measurement of the three-dimensional mean velocity, turbulence intensity, Reynolds stresses, static and stagnation pressures, and blade surface measurements. The high level of sophistication of rotor flow measurement techniques is demonstrated. Rotating probe measurements are well suited for low- and moderate-speed turbomachinery, while stationary quick-response probes (hot-wire and pressure probes) are applicable both in low- and high-speed turbomachines. Hot-wire probes, blade pressure transducers, and telemetry systems will provide the urgently needed basic information on steady and unsteady flow through a blade passage, including blade boundary layer, shock configuration, leakage and secondary flows.

Lakshminarayana, B.↗

NASA NTRS1980

An axial flow research compressor facility designed for flow measurement in rotor passages

An axial flow research compressor facility, which is designed for relative flow measurement, is described in this paper. The facility has a rotating probe traverse mechanism which is capable of traversing hot wire, pitot and other probes at 0.09 deg intervals across the rotor blade passage. The data transmission system includes rotating transducers, pressure transfer device, ten-channel mercury slip ring unit, scanivalve, etc. The instrumentation includes on-line data processing capability. A brief description of probes used as well as some typical data on the rotor blade static pressure, rotor endwall flow and rotor wake characteristics are given in the paper.

Lakshminarayana, B.↗

NASA NTRS1980

An investigation of the modulation of capillary and short gravity waves in the open ocean

A preliminary investigation of the modulation of capillary and gravity waves by long ocean waves is described. A pressure transducer is used to obtain water surface displacements, and a high-response laser-optical system is used to detect short-wave slopes. Analytical techniques are developed to account for the orbital motion of long waves. The local mean squared wave slope is found to be maximum leeward of the long-wave crests. For the long waves studied here and for short waves from 1 cm to 1 m, the longer a short-wave component is, the more leeward its maximum tends to occur. Also, the shortest waves tend to modulate least. The modulation of short waves is found to be strong enough to be an important component of the synthetic aperture radar image formation mechanism for long ocean waves.

Evans, D. D.↗

NASA NTRS1982

Modular Engine Instrumentation System

System that provides information and measurements never obtained before in real time has been developed. System shows not only real-time measurements but also results of computations of key combustion parameters in meaningful and easily understood display. Standard commercially-available shaft encoder plus data from pressure transducer act as principal drivers to device. Eventually, modular system could be developed into onboard controller for automobile engines.

Rice, W. J.↗

NASA NTRS1980

Tangential mode combustion instability of solid propellant rocket motors. 2: Pressure, frequency, and burning rate histories

The relationships among excursions of mean chamber pressure, high frequency pressure oscillations and accelerations associated with tangential mode combustion instability are considered. A data reduction procedure was devised to utilize the precise pressure time data as input to a numerical solution of the chamber mass balance relationships. The results indicate that both elevated burning rate induced by the tangential wave motions and variable nozzle blockage due to passage of vortical flow through the nozzle throat must act together to generate the large mean pressure peaks observed in the tests. There is strong correlation between the amplitude of wave motions and the level of mean pressure rise. Evidence for the presence of traveling tangential waves at the time of the D.C. shift was found by use of dual Kistler pressure transducers mounted at the head end of the burner. A very unusual frequency history was found to accompany the high amplitude disturbances. This was consistent from test to test and may represent an additional source of information regarding the complicated flow combustion interactions within the propellant burning zone.

Flandro, G. A.↗

NASA NTRS1981

Preliminary investigation of acoustic oscillations in an H2-O2 fired Hall generator

Burner pressure oscillations and interelectrode voltage oscillations measured in an open-cycle supersonic flow Hall generator are presented. The ionized gas for the channel was supplied by seeding the approximately 1 lb/sec of hydrogen-oxygen combustion products with cesium. Since both the burner and the channel were located within magnetic fields exceeding 4 Tesla during operation, an infinite probe pressure measurement technique was used to measure burner pressure oscillations. Calibration of the burner pressure transducer using a resonance tube technique is presented. Evidence is presented for the existence of the first longitudinal mode of oscillations (5000 Hz) within the burner. Interelectrode voltage oscillations were simultaneously measured at two separate axial stations. The magnitude change and the phase shift between the two signals was interpreted as a decaying magnetoacoustic wave driven by the burner that propagates at local gas plus sonic velocities. The amplitude of the electrical voltage oscillations at the start of the power producing region of the channel varied with the magnetic field. This variation is compared with the results of a simple perturbation analysis. Arguments are presented for using an unsteady model for analyzing wave processes in channels.

Phillips, B.↗

NASA NTRS1981

Mechanism of instabilities in turbulent combustion leading to flashback

High-speed schlieren cinematography, combined with synchronized pressure transducer records, was used to investigate the mechanism of combustion instabilities leading to flashback. The combustion chamber had an oblong rectangular cross-section to model the essential features of planar flow, and was provided with a rearward facing step acting as a flameholder. As the rich limit was approached, three instability modes were observed: (1) humming - a significant increase in the amplitude of the vortex pattern; (2) buzzing - a large-scale oscillation of the flame; and (3) chucking - a cyclic reformation of the flame, which results in flashback. The mechanism of these phenomena is ascribed to the action of vortices in the recirculation zone and their interactions with the trailing vortex pattern of the turbulent mixing layer behind the step.

Keller, J. O.↗