SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A numerical procedure was developed for minimizing the structural mass of an aircraft structure which must have a specified minimum flutter velocity or divergence velocity. During the optimization process the arrangement of the structural members remains fixed, while the stiffness parameters of the structure are varied.
The acousto-ultrasonic technique combines advantageous aspects of acoustic emission and ultrasonic methodologies. Acousto-ultrasonics operates by introducing a repeating series of ultrasonic pulses into a material. The waves introduced simulate the spontaneous stress waves that would arise if the material were put under stress as in the case of acoustic emission measurements. These benign stress waves are detected by an acoustic emission sensor. The physical arrangement of the ultrasonic (input) transducer and acoustic emission (output) sensor is such that the resultant waveform carries an imprint of morphological factors that govern or contribute to material performance. The output waveform is complex, but it can be quantitized in terms of a 'stress wave factor.' The stress wave factor, which can be defined in a number of ways, is a relative measure of the efficiency of energy dissipation in a material. If flaws or other material anomalies exist in the volume being examined, their combined effect appears in the stress wave factor.
Computerized infrared analysis is applied to the characterization of a glass-reinforced crosslinked polyester. The method of factor analysis determines the number of independent components which constitute the polymeric matrix. Subsequently, the spectra of those components are fitted by a least-squares criterion to spectra of the multicomponent matrix, or, if the glass spectrum is included as an additional component, to the spectra of composites. The least-squares coefficients yield the matrix composition in terms of the initial reactant composition and the extent of crosslinking.
Computerized infrared analysis is applied to the characterization of a glass-reinforced crosslinked polyester. The method of factor analysis determines the number of independent components which constitute the polymeric matrix. Subsequently, the spectra of those components are fitted by a least-squares criterion to spectra of the multicomponent matrix, or, if the glass spectrum is included as an additional component, to the spectra of composites. The least-squares coefficients yield the matrix composition in terms of the initial reactant composition and the extent of crosslinking.
The acousto-ultrasonic technique combines advantageous aspects of acoustic emission and ultrasonic methodologies. Acousto-ultrasonics operates by introducing a repeating series of ultrasonic pulses into a material. The waves introduced simulate the spontaneous stress waves that would arise if the material were put under stress as in the case of acoustic emission measurements. These benign stress waves are detected by an acoustic emission sensor. The physical arrangement of the ultrasonic (input) transducer and acoustic emission (output) sensor is such that the resultant waveform carries an imprint of morphological factors that govern or contribute to material performance. The output waveform is quite complex, but it can be quantitized in terms of a 'stress wave factor'. The stress wave factor, which can be defined in a number of ways, is essentially a relative measure of the efficiency of energy dissipation in a material. If flaws or other material anomalies exist in the volume being examined, their combined effect will appear in the stress wave factor.
Annealing at temperatures below the glass transition temperature (sub-T/g/ annealing) in structural epoxy network glasses is found to affect long-term mechanical properties of symmetrically (+ or - 45 deg) reinforced 16-lamina graphite/epoxy composites. Post-cured specimens of Thornel 300 graphite/Narmco 5208 epoxy are sub-T(g) annealed at 140 C for about 10, 100, 1000, 10,000, and 100,000 min with a prior quenching above T(g). The ultimate tensile strength, strain-to-break, and static toughness of the composite materials are found to decrease as a function of sub-T(g) annealing time, while no weight loss is observed. Time-dependent changes in properties are explained by a physical aging concept based on free-volume decreases in the nonequilibrium glassy state of network epoxies, and results imply that changes in composite properties may occur with the service time.
Presented is a theory to predict the room-temperature shape of unsymmetric laminates. The theory is an extension of classical lamination theory and includes the effects of geometric nonlinearities. It is shown that the saddle shape predicted by the classical theory can actually be an unstable shape and a laminate will assume a cylindrical shape instead. The phenomena is coupled to the length, width, and thickness of the laminate.
(Previously announced in STAR as N82-15198)
The advantageous aspects of acoustic emission and ultrasonic methodologies are combined in a technique which operates by introducing a repeating series of ultrasonic pulses into a material. The waves introduced simulate the spontaneous stress waves that would arise if the material were put under stress as in the case of acoustic emission measurements. These benign stress waves are detected by an acoustic emission sensor. The physical arrangement of the ultrasonic (input) transducer and acoustic emission (output) sensor is such that the resultant waveform carries an imprint of morphological factors that govern or contribute to material performance. The output waveform is quite complex, but it can be quantitized in terms of a "stress wave factor". The stress wave factor, which can be defined in a number of ways, is essentially a relative measure of the efficiency of energy dissipation in a material. If flaws or other material anomalies exist in the volume being examined, their combined effect will appear in the stress wave factor.
Graphite/epoxy (T300/5208) and graphite/polyimide composites (C6000/PMR 15) were exposed to various levels of 0.5 MeV electron radiation with the maximum dose being 10,000 Mrad. A three point bending test was used to evaluate the ultimate stress and modulus of the composites. In all composites except transverse samples of C6000/PMR 15 ultimate stress values remained approximately constant or increased slightly. The modulus values remained approximately constant for all composite types regardless of the radiation level. Interfacial aspects of composites were studied. Interlaminar shear tests were performed on T300/5208 and C6000/PMR 15 composites irradiated to 10,000 Mrad. There was an initial increase in interlaminar shear strength (up to 1,000 Mrad) followed by a sharp decrease with further radiation exposure. Using scanning electron microscopy no visual differences in the mode of fracture could be detected between ruptured control samples and those exposed to various levels of radiation. Electron spectroscopy for chemical analysis (ESCA) revealed little change in the surface elements present in control and highly irradiated T300/5208 composite samples.
Annealing in nitrogen below the glass transition temperature T(g) is found to affect the matrix-dominated physical properties of postcured, (+ and -45)2s specimens of Thornel 300 carbon fiber/Fiberite 934 epoxy composite as well as neat Fiberite 934 epoxy resin. The damping behavior, stress-relaxation rate and enthalpic state of the matrix material are found to decrease as functions of annealing time. The time-dependent change in physical properties is explained on the basis of free-volume collapse related to the physical aging of the nonequilibrium glassy network of epoxy. Such physical aging in network epoxy has been demonstrated to be thermoreversible through the monitoring of its kinetics by differential scanning calorimetry, stress relaxation tests, and dynamic mechanical analysis.
A method for the experimental and analytical accelerated characterization of long term viscoelastic properties is presented. The time-temperature-stress superposition principle (TTSSP) is shown to serve as the basis for determining long term compliance data from short term creep test results. Nonlinear viscoelastic theories are discussed to provide the framework for the mathematically modeling of such a process. A time dependent Tsai-Hill-Zhurkov failure theory is used to determine long term failure properties from short term data. Compliance and failure data are incorporated in an incremental lamination theory to make long term laminate predictions. Comparisons are made between theory and experiment.
Explore the source record for details and available documents.
The objective of this project was to develop a user-friendly interactive computer program to be used as an analytical tool by structural designers. Its intent was to do preliminary, approximate stress analysis to help select or verify sizing choices for composite structural members. The approach to the project was to provide a subroutine which uses classical lamination theory to predict an effective elastic modulus for a laminate of arbitrary material and ply orientation. This effective elastic modulus can then be used in a family of other subroutines which employ the familiar basic structural analysis methods for isotropic materials. This method is simple and convenient to use but only approximate, as is appropriate for a preliminary design tool which will be subsequently verified by more sophisticated analysis. Additional subroutines have been provided to calculate laminate coefficient of thermal expansion and to calculate ply-by-ply strains within a laminate.
Graphite-reinforced aluminum alloy metal-matrix composites are among materials being considered for structural components in dimensionally stable space structures. This application requires materials with low values of thermal expansions and high specific stiffnesses. They must remain stable during exposures to the space environment for periods extending to 20 years. The effects of thermal cycling on the thermal expansion behavior and mechanical properties of Thornel P100 graphite 6061 aluminum composites, as fabricated and after thermal processing to eliminate thermal strain hysteresis, have been investigated. Two groups of composites were studied: one was fabricated by hot roll bonding and the other by diffusion bonding. Processing significantly reduced strain hysteresis during thermal cycling in both groups and improved the ultimate tensile strength and modulus in the diffusion-bonded composites. Thermal cycling stabilized the as-fabricated composites by reducing the residual fabrication stress and increased the matrix strength by metallurgical aging. Thermal expansion behavior of both groups after processing was insensitive to thermal cycling. Data scatter was too large to determine effects of thermal cycling on the mechanical properties. The primary effects of processing and thermal cycling can be attributed to changes in the metallurgical condition and stress state of the matrix.
Results obtained on the postbuckling behavior of plates and curved panels using the NOLIN computer program are reported. As an example, the postbuckling behavior of a flexible, isotropic and quadrangular plate is solved and the results are found to be accurate and relibale in comparison with those in the literature. The fatigue-deformation behavior of a rectangular CKL plate is measured, and the results are compared with those from NOLIN and other computer programs. A slightly curved panel with optimized layering is studied.
A technique is described that makes it possible to transmit and receive bulk ultrasonic waves launched from the same surface of a composite sheet by means of transducers mounted on variable angle blocks. A straightforward approach to measure the velocity and attenuation of this wave is presented. A bulk compressional wave of 930,000 cm/sec velocity was launched and received in this manner in an 8-ply unidirectional T-300-5208 epoxy composite. Preliminary results indicate that parameters associated with this wave might be sensitive to accumulated damage in a composite; thus, the technique has a potential for NDE in structures made from composite materials.
An experimental program to develop test methods to be used to characterize interfacial (autohesive) strength development in polysulfone thermoplastic resin and graphite-polysulfone prepreg during processing is reported. Two test methods were used to examine interfacial strength development in neat resin samples. These included an interfacial tension test and a compact tension (CT) fracture toughness test. The interfacial tensile test proved to be very difficult to perform with a considerable amount of data scatter. Thus, the interfacial test was discarded in favor of the fracture toughness test. Interfacial strength development was observed by measuring the refracture toughness of precracked compact tension specimens that were rehealed at a given temperature and contact time. The measured refracture toughness was correlated with temperature and contact time. Interfacial strength development in graphite-polysulfone unidirectional composites was measured using a double cantilever beam (DCB) interlaminar fracture toughness test. The critical strain energy release rate of refractured composite specimens was measured as a function of healing temperature and contact time.