Search NASA⌕ Search

SEARCH · Search NASA

Results for “Signal Processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Coincidence probabilities for spacecraft gravitational wave experiments - Massive coalescing binaries

Massive coalescing binary systems are candidate sources of gravitational radiation in the millihertz frequency band accessible to spacecraft Doppler tracking experiments. This paper discusses signal processing and detection probability for waves from coalescing binaries in the regime where the signal frequency increases linearly with time, i.e., 'chirp' signals. Using known noise statistics, thresholds with given false alarm probabilities are established for one- and two-spacecraft experiments. Given the threshold, the detection probability is calculated as a function of gravitational wave amplitude for both one- and two-spacecraft experiments, assuming random polarization states and under various assumptions about wave directions. This allows quantitative statements about the detection efficiency of these experiments and the utility of coincidence experiments. In particular, coincidence probabilities for two-spacecraft experiments are insensitive to the angle between the directions to the two spacecraft, indicating that near-optical experiments can be done without constraints on spacecraft trajectories.

Tinto, Massimo↗
NASA NTRS1994

Satellite Multicarrier Demodulation System

Proposed onboard signal processing system for communications satellites performs real-time conversion of multiple uplink (received) signals in single-channel-per-carrier, frequency-division-multiple-access (SCPC/FDMA) format to downlink (transmitted) signals in time-division-multiplexed (TDM) format. Conversion approach enhances use of allocated spectrum and reduces required effective isotropic radiated power at both transponder (satellite) and Earth stations. Equipment needed to implement scheme less complex and less expensive than time-division-multiple-access (TDMA) formats. More economical future satellite communication systems made possible through use of many small-capacity multiservice Earth terminals.

Budinger, James↗
NASA NTRS2002

Experimental Investigations of Non-Stationary Properties In Radiometer Receivers Using Measurements of Multiple Calibration References

Radiometers must be periodically calibrated because the receiver response fluctuates. Many techniques exist to correct for the time varying response of a radiometer receiver. An analytical technique has been developed that uses generalized least squares regression (LSR) to predict the performance of a wide variety of calibration algorithms. The total measurement uncertainty including the uncertainty of the calibration can be computed using LSR. The uncertainties of the calibration samples used in the regression are based upon treating the receiver fluctuations as non-stationary processes. Signals originating from the different sources of emission are treated as simultaneously existing random processes. Thus, the radiometer output is a series of samples obtained from these random processes. The samples are treated as random variables but because the underlying processes are non-stationary the statistics of the samples are treated as non-stationary. The statistics of the calibration samples depend upon the time for which the samples are to be applied. The statistics of the random variables are equated to the mean statistics of the non-stationary processes over the interval defined by the time of calibration sample and when it is applied. This analysis opens the opportunity for experimental investigation into the underlying properties of receiver non stationarity through the use of multiple calibration references. In this presentation we will discuss the application of LSR to the analysis of various calibration algorithms, requirements for experimental verification of the theory, and preliminary results from analyzing experiment measurements.

Racette, Paul↗
NASA NTRS2018

Combustion Stability Evaluation of Artificial Disturbance Dynamic Response

General guidelines are provided in CPIA Publication 6551 for evaluation of the response due to an artificial disturbance, however the guideline also allows for ambiguous interpretation. Stability rating devices that produce an artificial disturbance are traditionally explosive bombs and pulse guns. This paper reviews a recently developed objective process that can be applied consistently in the reduction of artificial disturbance dynamic data. It also examines three methods of response evaluation. The first method examines the response of a specific mode of interest and requires data filtering encompassing that mode. The second method examines the response of a specific mode of interest and its nonlinear components and requires a more complex filtering scheme. The third method examines the response of the entire dynamic system and consists of examining a wide bandwidth consisting of multiple modes of interest. The evaluation process is described and the advantages and disadvantages of the evaluation methods are discussed. Signal processing is used as a tool in quantifying the assessment, clearly as an improvement from the subjective heritage approach consisting primarily of engineering judgement. Data for several engines and components have been compiled and evaluated using these methods. A summary of these combustion devices is provided and observations are discussed.

Casiano, M. J.↗
NASA NTRS1987

A computer controlled signal preprocessor for laser fringe anemometer applications

The operation of most commercially available laser fringe anemometer (LFA) counter-processors assumes that adjustments are made to the signal processing independent of the computer used for reducing the data acquired. Not only does the researcher desire a record of these parameters attached to the data acquired, but changes in flow conditions generally require that these settings be changed to improve data quality. Because of this limitation, on-line modification of the data acquisition parameters can be difficult and time consuming. A computer-controlled signal preprocessor has been developed which makes possible this optimization of the photomultiplier signal as a normal part of the data acquisition process. It allows computer control of the filter selection, signal gain, and photo-multiplier voltage. The raw signal from the photomultiplier tube is input to the preprocessor which, under the control of a digital computer, filters the signal and amplifies it to an acceptable level. The counter-processor used at Lewis Research Center generates the particle interarrival times, as well as the time-of-flight of the particle through the probe volume. The signal preprocessor allows computer control of the acquisition of these data.Through the preprocessor, the computer also can control the hand shaking signals for the interface between itself and the counter-processor. Finally, the signal preprocessor splits the pedestal from the signal before filtering, and monitors the photo-multiplier dc current, sends a signal proportional to this current to the computer through an analog to digital converter, and provides an alarm if the current exceeds a predefined maximum. Complete drawings and explanations are provided in the text as well as a sample interface program for use with the data acquisition software.

Oberle, Lawrence G.↗
NASA NTRS1985

Ultrasonic inspection of carbon fiber reinforced plastic by means of sample-recognition methods

In the case of carbon fiber reinforced plastic (CFRP), it has not yet been possible to detect nonlocal defects and material degradation related to aging with the aid of nondestructive inspection method. An approach for overcoming difficulties regarding such an inspection involves an extension of the ultrasonic inspection procedure on the basis of a use of signal processing and sample recognition methods. The basic concept involved in this approach is related to the realization that the ultrasonic signal contains information regarding the medium which is not utilized in conventional ultrasonic inspection. However, the analytical study of the phyiscal processes involved is very complex. For this reason, an empirical approach is employed to make use of the information which has not been utilized before. This approach uses reference signals which can be obtained with material specimens of different quality. The implementation of these concepts for the supersonic inspection of CFRP laminates is discussed.

Bilgram, R.↗
NASA NTRS2012

High-Speed Edge-Detecting Line Scan Smart Camera

A high-speed edge-detecting line scan smart camera was developed. The camera is designed to operate as a component in a NASA Glenn Research Center developed inlet shock detection system. The inlet shock is detected by projecting a laser sheet through the airflow. The shock within the airflow is the densest part and refracts the laser sheet the most in its vicinity, leaving a dark spot or shadowgraph. These spots show up as a dip or negative peak within the pixel intensity profile of an image of the projected laser sheet. The smart camera acquires and processes in real-time the linear image containing the shock shadowgraph and outputting the shock location. Previously a high-speed camera and personal computer would perform the image capture and processing to determine the shock location. This innovation consists of a linear image sensor, analog signal processing circuit, and a digital circuit that provides a numerical digital output of the shock or negative edge location. The smart camera is capable of capturing and processing linear images at over 1,000 frames per second. The edges are identified as numeric pixel values within the linear array of pixels, and the edge location information can be sent out from the circuit in a variety of ways, such as by using a microcontroller and onboard or external digital interface to include serial data such as RS-232/485, USB, Ethernet, or CAN BUS; parallel digital data; or an analog signal. The smart camera system can be integrated into a small package with a relatively small number of parts, reducing size and increasing reliability over the previous imaging system..

Prokop, Norman F.↗
NASA NTRS1989

Enhanced imaging of reflector antenna surface distortion using microwave holography

Two signal processing techniques are discussed that improve the accuracy of a microwave holographic measurement by removing unwanted signals from the aperture distribution: pattern simulation and subtraction, and time domain filtering. Pattern simulation and subtraction involves modeling unwanted scattering mechanisms and then removing them from the measured far-field data. Measurements taken on a focal point geometry and a Cassegrain geometry at 11 GHz were processed by the holographic analysis system. Pattern simulation and subtraction was applied to both geometries. Surface deformation profiles generated for the Cassegrain antenna by this system were compared to an optical measurement of the main reflector surface.

Gilmore, Sean W.↗
NASA NTRS1977

Design of an airborne lidar for stratospheric aerosol measurements

A modular, multiple-telescope receiving concept is developed to gain a relatively large receiver collection aperture without requiring extensive modifications to the aircraft. This concept, together with the choice of a specific photodetector, signal processing, and data recording system capable of maintaining approximately 1% precision over the required large signal amplitude range, is found to be common to all of the options. It is recommended that development of the lidar begin by more detailed definition of solutions to these important common signal detection and recording problems.

Evans, W. E.↗
NASA NTRS1981

CCD sensors for interplanetary spacecraft navigation and pointing control

The applications of practical optical image sensing CCDs to interplanetary spacecraft precision science payload delivery are discussed. The increasing demand for precision and flexibility in spacecraft for proposed new missions is forcing a transition to autonomous onboard navigation and pointing control. Onboard processing of video data is a crucial element in this transition and is made possible by CCD imagers and microprocessors. The pending Halley's comet close flyby is used as an example to examine details of the sensor design and the data processing which will meet the requirements. Target body centerfinding for optical navigation, target body tracking signal processing, and CCD sensor heads are examined, and flow charts and block diagrams are given for each.

Eisenman, A. R.↗
NASA NTRS1993

Digital receiver for on-board FM/FSK-FM/BPSK demodulation

An all-digital demodulator FM/FSK-FM/BPSK is presented. The proposed architecture allows the 1-bit IF down-sampling technique with the hardware simplification of receiver analog section. The receiver exhibits great flexibility both in terms of signal demodulation (FSK or BPSK, subcarrier/ tone frequency, data rate) and interface capability. The demodulator is going to be realized in a VLSI chip (20 Kgate complexity). This paper describes the demodulator structure and its demodulation performances obtained with a breadboard based on programmable logic devices. The choice of a simple and effective scheme for frequency detection (FM and FSK demodulators) is suggested by system design considerations as well. Signal processing algorithms include also a Costas carrier phase recovery scheme in the case of BPSK signal and data transition tracking loop for the bit clock recovery. Test results address this solution as one of the most suitable for TT&C space application.

Boscagli, G.↗
NASA NTRS1995

Power control electronics for cryogenic instrumentation

In order to achieve a high-efficiency high-density cryogenic instrumentation system, the power processing electronics should be placed in the cold environment along with the sensors and signal-processing electronics. The typical instrumentation system requires low voltage dc usually obtained from processing line frequency ac power. Switch-mode power conversion topologies such as forward, flyback, push-pull, and half-bridge are used for high-efficiency power processing using pulse-width modulation (PWM) or resonant control. This paper presents several PWM and multiresonant power control circuits, implemented using commercially available CMOS and BiCMOS integrated circuits, and their performance at liquid-nitrogen temperature (77 K) as compared to their room temperature (300 K) performance. The operation of integrated circuits at cryogenic temperatures results in an improved performance in terms of increased speed, reduced latch-up susceptibility, reduced leakage current, and reduced thermal noise. However, the switching noise increased at 77 K compared to 300 K. The power control circuits tested in the laboratory did successfully restart at 77 K.

Ray, Biswajit↗
NASA NTRS2012

Wideband Agile Digital Microwave Radiometer

The objectives of this work were to take the initial steps needed to develop a field programmable gate array (FPGA)- based wideband digital radiometer backend (>500 MHz bandwidth) that will enable passive microwave observations with minimal performance degradation in a radiofrequency-interference (RFI)-rich environment. As manmade RF emissions increase over time and fill more of the microwave spectrum, microwave radiometer science applications will be increasingly impacted in a negative way, and the current generation of spaceborne microwave radiometers that use broadband analog back ends will become severely compromised or unusable over an increasing fraction of time on orbit. There is a need to develop a digital radiometer back end that, for each observation period, uses digital signal processing (DSP) algorithms to identify the maximum amount of RFI-free spectrum across the radiometer band to preserve bandwidth to minimize radiometer noise (which is inversely related to the bandwidth). Ultimately, the objective is to incorporate all processing necessary in the back end to take contaminated input spectra and produce a single output value free of manmade signals to minimize data rates for spaceborne radiometer missions. But, to meet these objectives, several intermediate processing algorithms had to be developed, and their performance characterized relative to typical brightness temperature accuracy re quirements for current and future microwave radiometer missions, including those for measuring salinity, soil moisture, and snow pack.

Gaier, Todd C.↗
NASA NTRS1984

Fuel spray diagnostics

Several laser measurement methods are being studied to provide the capability to make droplet size and velocity measurements under a variety of spray conditions. The droplet sizing interferometer (DSI) promises to be a successful technique because of its capability for rapid data acquisition, compilation and analysis. Its main advantage is the ability to obtain size and velocity measurements in air-fuel mixing studies and hot flows. The existing DSI at NASA Lewis is a two-color, two-component system. Two independent orthogonal measurements of size and velocity components can be made simultaneously. It also uses an off-axis large-angle light scatter detection. The fundamental features of the system are optics, signal processing and data management system. The major component includes a transmitter unit, two receiver units, two signal processors, two data management systems, two Bragg cell systems, two printer/plotters, a laser, power supply and color monitor.

Bosque, M. A.↗
NASA NTRS1989

Molecular-Beam Epitaxy Of CrSi2 on Si(111)

Crystalline layers grown in commercial apparatus. Experiments show CrSi2 grown on (111) face of single-crystal Si substrate by molecular-beam epitaxy. Epitaxial CrSi2 produced thus far not in desired single-crystal form. Because CrSi2 semiconductor with band gap of 0.3 eV, experimental process potential for monolitic integration of microelectronic devices based on CrSi2 (e.g., infrared detectors) with signal-processing circuitry based on Si.

Fathauer, Robert W.↗
NASA NTRS1972

A surface wave spread spectrum communication link.

This development has resulted in a fast lock-up, 8-MHz bandwidth, 8-KHz data rate, spread spectrum communication link breadboard that is implemented using surface wave devices as the primary signal generators and signal processing elements. It uses surface wave tapped delay lines (SWTDL's) in the transmitter to generate the signals and in the receiver to match filter detect them. The system also incorporates a re-entry delay line (circulating integrator) which increases the effective code length per data bit by eight-fold.

Fugit, B. R.↗
NASA NTRS1974

A priori estimate of the quality of a data compression system based on statistical characteristics of the sensors used

Knowledge of the composition and certain statistical characteristics of the output signals of the scientific instruments on board a space vehicle allows determination of possible signal processing algorithms in the system and to evaluate the prospects for utilization of data reduction. A method is presented to estimate the compression factor of an on-board data collection and processing system with known mean activities of the sensors used and unknown mutual correlation of their output signals.

Khodarev, Y. K.↗