Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solar control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Performance analysis and simulation of the SPS reference phase control system

The solar power satellite (SPS) concept envisions several hundred thousand synchronized microwave power amplifiers operating in parallel to produce an aggregate power output of 5-10 GW. This power is to be transferred to earth with the aid of a microwave/millimeter-wave beaming system operating in a synchronous orbit. The reference phase control system is considered along with aspects of pilot signal parameter selection. A power transponder analysis is conducted and an SPS performance evaluation is performed. Attention is given to system jitters and imperfections, the definition of power transfer efficiency, and the effects of system imperfections on SPS efficiency. It is found that the power transfer efficiency is relatively insensitive to the amplitude jitters. However, the effects of location jitters can produce a severe degradation of efficiency.

Chie, C. M.↗

Aircraft control system

A solar rechargeable, long-duration, span-loaded flying wing, having no fuselage or rudder. Having a two-hundred foot wingspan that mounts photovoltaic cells on most all of the wing's top surface, the aircraft uses only differential thrust of its eight propellers to turn, pitch and yaw. The wing is configured to deform under flight loads to position the propellers such that the control can be achieved. Each of five segments of the wing has one or more motors and photovoltaic arrays, and produces its own lift independent of the other segments, to avoid loading them. Five two-sided photovoltaic arrays, in all, are mounted on the wing, and receive photovoltaic energy both incident on top of the wing, and which is incident also from below, through a bottom, transparent surface.

Lisoski, Derek L.↗

A practical six-degree of freedom solar sail dynamics model for optimizing solar sail trajectories with torque constraints

Controlled flight of a solar sail-propelled spacecraft ('sailcraft') is a six-degree-of-freedom dynamics problem. Current state-of-the-art tools that simulate and optimize the trajectories flown by sailcraft do not treat the full kinetic (i.e. force and torque-constrained) motion, instead treating a discrete history of commanded sail attitudes, and either neglecting the sail attitude motion over an integration timestep, or treating the attitude evolution kinematically with a spline or similar treatment. The present paper discusses an aspect of developing a next generation sailcraf trajectory designing optimization tool JPL, for NASA's Solar Sail Spaceflight Simulation Software (SS). The aspect discussed in an experimental approach to modeling full six-degree-of-freedom kinetic motion of a solar sail in a trajectory propagator. Early results from implementing this approach in a new trajectory propagation tool are given.

six-degree-of-freedom↗

Orientation and shape-control of an orbiting flexible beam under the influence of solar radiation pressure

In this paper, the uncontrolled and controlled dynamics of a thin flexible beam in orbit and in the presence of solar radiation disturbance are analyzed. A beam nominally oriented along (i) the local horizontal and carrying a gimballed rigid dumbbell for gravity stabilization, and (ii) a beam nominally oriented along the local vertical are considered. The uncontrolled dynamics of the beam in the presence of the solar radiation pressure disturbance shows the excitation of the rigid pitch mode. The control laws previously designed for the case where the environmental effects were neglected, are found to be inadequate to control the shape and orientation of very flexible beams that are exposed to solar radiation disturbances. The control laws and the gain parameters are reevaluated for both cases of nominal beam orientations; this results, in general, in increased robustness of the closed-loop system. Methods of obtaining a robust control system in the presence of environmental perturbations are discussed.

Krishna, R.↗

Solar Thermal Upper Stage Liquid Hydrogen Pressure Control Testing

High-energy cryogenic propellant is an essential element in future space exploration programs. Therefore, NASA and its industrial partners are committed to an advanced development/technology program that will broaden the experience base for the entire cryogenic fluid management community. Furthermore, the high cost of microgravity experiments has motivated NASA to establish government/aerospace industry teams to aggressively explore combinations of ground testing and analytical modeling to the greatest extent possible, thereby benefitting both industry and government entities. One such team consisting of ManTech SRS, Inc., Edwards Air Force Base, and Marshall Space Flight Center (MSFC) was formed to pursue a technology project designed to demonstrate technology readiness for an SRS liquid hydrogen (LH2) in-space propellant management concept. The subject testing was cooperatively performed June 21-30, 2000, through a partially reimbursable Space Act Agreement between SRS, MSFC, and the Air Force Research Laboratory. The joint statement of work used to guide the technical activity is presented in appendix A. The key elements of the SRS concept consisted of an LH2 storage and supply system that used all of the vented H2 for solar engine thrusting, accommodated pressure control without a thermodynamic vent system (TVS), and minimized or eliminated the need for a capillary liquid acquisition device (LAD). The strategy was to balance the LH2 storage tank pressure control requirements with the engine thrusting requirements to selectively provide either liquid or vapor H2 at a controlled rate to a solar thermal engine in the low-gravity environment of space operations. The overall test objective was to verify that the proposed concept could enable simultaneous control of LH2 tank pressure and feed system flow to the thruster without necessitating a TVS and a capillary LAD. The primary program objectives were designed to demonstrate technology readiness of the SRS concept at a system level as a first step toward actual flight vehicle demonstrations. More specific objectives included testing the pressure and feed control system concept hardware for functionality, operability, and performance. Valuable LH2 thermodynamic and fluid dynamics data were obtained for application to both the SRS concept and to future missions requiring space-based cryogen propellant management.

Moore, J. D.↗

Preparation of morphology-controlled TiO{sub 2} nanocrystals for the excellent photocatalytic activity under simulated solar irradiation

Graphical abstract: Morphology-controlled TiO{sub 2} nanocrystals with excellent photocatalytic activity under simulated solar irradiation were successfully synthesized. - Highlights: • TiO{sub 2} nanocrystals (NCs) with different morphologies were synthesized. • The growth mechanism of morphology-controlled TiO{sub 2} NCs was proposed. • The core-shell structured TiO{sub 2} NCs (co-TiO{sub 2}) had a narrow band gap (2.67 eV). • The co-TiO{sub 2} NCs possessed excellent photocatalytic activity and recyclability. - Abstract: A simple synthetic approach based on solvothermal technique and hydrogenation was developed for preparation of TiO{sub 2} nanocrystals with different morphologies such as elongated rhombic, dog-bone, oval and core-shell structured oval. The effect of oleic acid (OA) and oleylamine (OM) as two capping surfactants on the growth of TiO{sub 2} nanocrystals was investigated. The physicochemical properties of the obtained samples were characterized by various techniques including TEM, XRD, UV–vis absorption, Raman, XPS, BET, PL and photocurrent measurement. In photodegradation of RhB under simulated solar irradiation, the oval-shaped TiO{sub 2} nanocrystals with core-shell structure (co-TiO{sub 2}) was superior to other TiO{sub 2} nanocrystals in catalytic activity. Moreover, the co-TiO{sub 2} nanocrystals exhibited well recyclability during multiple photocatalytic tests. These excellent properties of co-TiO{sub 2} were attributed to its special structure, including lattice-disordered surface layer and well-crystallized lattice core, and narrow band gap (2.67 eV).

36 MATERIALS SCIENCE↗

Systems and methods for single-axis tracking via sky imaging and machine leanring comprising a neural network to determine an angular position of a photovoltaic power system

A system and method is disclosed for solar tracking and controlling an angular position of a photovoltaic power system. The solar tracking system includes an imaging device for capturing images of the sky; a solar position data generating module; and a control system comprising a neural network. The neural network has multiple convolutional layers to generate a first output associated with the images, and a solar position data module. A first dense layer module receives the solar position data and generates a second output. A second dense layer module receives the first output and the second output and generates a concatenated data sequence. A processor is programmed to generate a multi-planar irradiance signal (MPIS) in response to the concatenated data sequence, and determine an angular position of the PV power system and adjust the angular position in response to an angle of maximum irradiance.

Stein, Joshua↗

Real time control of the observing program of an Orbiting Solar Observatory.

Discussion of some innovations in the ground control optimization of the modes of data acquisition once an instrument is in orbit, as illustrated by the Harvard experiment on OSO 6. A detailed description is given of the instrumentation on board OSO 6 which provided a capability of performing spatial scans of the solar disk and the ability to obtain the spectra of selected features on the solar disk. The method of receiving and displaying the data transmitted by the satellite in real time is described, as well as the procedure followed in developing preflight observing objectives and in evaluating completed observations. A typical process of data acquisition to obtain wavelength scans of selected features on the solar disk is illustrated, and a number of collaborative investigations involving simultaneous coordinated observations from the ground and from space are cited.

Reeves, E. M.↗

Solar cycle changes in the high latitude solar wind

Measurements of the solar wind velocity during the period 1971-79 using the technique of interplanetary scintillation are discussed. The average wind speed was faster than 500 km/s at latitudes above 30 deg for most of 1973-77. The fast polar stream, observed to become much narrower in 1978-79 is examined. The narrowing of the polar streams coincided with the emergence of sunspots at midlatitudes, with the start of the new solar cycle, and with a corresponding contraction of the polar coronal holes. The theory that the solar magnetic field controls the large scale structure of the solar wind is discussed in relation to the results.

Rickett, B. J.↗

NASA advanced design program: Analysis, design, and construction of a solar powered aircraft

Increase in energy demands coupled with rapid depletion of natural energy resources have deemed solar energy as the most logical alternative source of power. The major objective of this project was to build a solar powered remotely controlled aircraft to demonstrate the feasibility of solar energy as an effective, alternate source of power. The final design was optimized for minimum weight and maximum strength of the structure. These design constraints necessitated a carbon fiber composite structure. Surya is a lightweight, durable aircraft capable of achieving level flight powered entirely by solar cells.

Chan, Agnes↗

Dynamic Building Load Control to Facilitate High Penetration of Solar Photovoltaic Generation (Final Technical Report)

Solar photovoltaic (PV) resources are the most common form of distributed generation in residential and commercial customer premises within electric distribution networks. A higher penetration of PV generation in distribution circuits will impose challenges on maintaining service voltages within the range of industry standards, power quality, and power flow. Buildings consume 74% of the electricity produced in the United States, and a significant portion of the building load is dispatchable, making them responsive to electrical grid needs. Oak Ridge National Laboratory—in collaboration with Southern Company; the University of Tennessee, Knoxville; and the Georgia Institute of Technology—is examining the PV integration issues in distribution-level electrical grids and developing integrated demand-side control and communication systems to enable responsive loads. The proposed responsive loads mechanism performs renewable generation following to increase the penetration of solar PV within each feeder. The specific objectives of this project are to (1) examine distribution-level PV integration scenarios to understand requirements, (2) undertake an end-to-end simulation-based design of a distributed control strategy of loads geographically near the PV generation asset to minimize the effect on the distribution feeder, (3) deploy and demonstrate the control technology developed in partnership with utilities, and (4) perform a scalability analysis at the utility scale. This 3-year integrated project aims to develop, demonstrate, and validate demand-side control technology to enable increased the penetration of renewables while mitigating challenges that arise due to their intermittency. Activities in Budget Period (BP) 1 focused on a literature review and the formal design of a control system for integrating local distribution with generation and loads. The team used modeling and simulation to evaluate the impact of varying buildings loads, variable PV generation, and power flow dynamics on the distribution circuit. The dynamic models developed in BP 1 were used in BP 2 to develop a model-based control design and a test bed. The test bed has enabled the simulation-based testing and comparison of different control designs and formulations applied to different configurations of the distribution grid, PVs, and building loads. The control approaches developed in BP 2 were implemented in BP 3 in the form of hardware deployed at the Central Baptist Church (CBC) in Knoxville, Tennessee, for testing and evaluation. The outcome of this project was the development and demonstration of open-source, low-cost, low-touch sensing and control retrofits to distributed PV generation and building loads that, in a coordinated fashion, provide the load-shaping response needed to integrate high levels of renewable penetration. This research addresses the target metrics by dynamically controlling a load with solar generation variability to minimize the extent of two-way power flow, enhance reliability, facilitate high PV penetration (>100% of peak load in a line segment), and generate scalable software and hardware solutions adaptable to any penetration levels. The research and development activities are focused and designed to be impactful within the relevant 2020 targets time frame.An accurate open-source integration simulation framework for end-to-end control design was developed and deployed at the CBC facility for testing and evaluation. This final report provides a detailed review of the technical results achieved during this 3-year integrated project. A novel spectral analysis of PV data is demonstrated to derive the requirements of the control design. A detailed simulation-based analysis of PV integration at increasing penetration levels is presented using 1 year of PV data to demonstrate the impact on the distribution circuits. Two different control strategies were developed and demonstrated via simulation to track variable PV generation with adaptive load dispatch. The report concludes with a summary of accomplishments and recommendations for a path forward.

14 SOLAR ENERGY↗

Privacy-Preserving Aggregation of Controllable Loads to Compensate Fluctuations in Solar Power

Cybersecurity and privacy are of the utmost importance for safe, reliable operation of the electric grid. It is well known that the increased connectivity/interoperability between all stakeholders (e.g., utilities, suppliers, and consumers) will enable personal information collection. Significant advanced metering infrastructure (AMI) deployment and demand response (DR) programs across the country, while enable enhanced automation, also generate energy data on individual consumers that can potentially be used for exploiting privacy. Inspired by existing works which consider DR, battery-based perturbation, and differential privacy noise adding, we novelly consider the aggregator (cluster) level privacy issue in the DR framework of solar photovoltaic (PV) generation following. Different from most of the existing works which mainly rely on the charging/discharging scheduling of rechargeable batteries, we utilize controllable building loads to serve as virtual storage devices to absorb a large portion of the PV genertaion while delicately keeping desired noisy terms to satisfy the differential privacy for the raw load profiles at the aggregator level. This not only ensures differential privacy, but also improves the DR efficiency in load following since part of the noisy signal in solar PV generation has been filtered out. In particular, a mixed integer quadratic optimization problem is formulated to optimally dispatch a population of on/off controllable loads to achieve this privacy-preserving DR service.

Dong, Jin↗

Solar power satellite microwave system concepts and performance considerations

The phase control system is the fundamental element in the forming, steering and control of the solar power satellite (SPS) microwave power beam. This system must in essence automatically adjust the phase at each of the transmitter's 101,552 power amplifiers to compensate for differences in transmission path lengths to the earth-based receiving antenna (rectenna). SPS phase control system requirements are discussed, taking into account system concepts, a reference system description, reference system performance, ground based phase control concepts, and ionosphere considerations. It is pointed out that the importance of determining the ionospheric effects cannot be overemphasized. The permissable power density limit through the ionosphere is a critical SPS sizing factor and the phase control system must be able to accommodate errors induced by a heated ionosphere.

Seyl, J. W.↗

Side Chain and Solvent Direction of Film Morphology in Small-Molecule Organic Solar Materials

Film morphology control is essential to materials development for efficient organic solar cells (OSCs). Unlocking methods to optimize the film morphology for materials without changing the fundamental electronic characteristics can enable previously unacceptable materials to achieve high performance. In this work, a series of acceptor-donor-acceptor (ADA) small molecule p-type OSC semiconductors having benzo[1,2-b:6,5-b0]dithiophene (bBDT) donor units and thiophene capped diketopyrrolopyrrole (TDPP) acceptor units are examined where the sole molecular design variation is in the electronically inactive side chains. Four bBDT(TDPP) 2 compounds with all possible combinations of either 2-ethelhexyl (EH), or 3,7-dimtheyloctyl (DMO) side chains on the bBDT core and TDPP units are discussed. When processed from a chloroform (CF)-only solution, blend films of the molecules with the PC 71 BM electron acceptor exhibit similar thin film properties and photovoltaic performance, regardless of the side chain composition. However, when the additive 1,8-diiodooctane (DIO) is included in the processing solution, the morphological properties and OSC performance diverge dramatically, with the side chain variations now dictating the film morphology, resulting in a >400% spread in power conversion efficiency (PCE). Donor molecules with a mixed side chain motif having the larger DMO side chain on the bBDT core unit deliver the best performance owing to greater donor:acceptor phase intermixing while maintaining contiguous and efficient charge transport pathways. Using in situ GIWAXS during spin-coating, it is shown that DIO extends crystallization times, thereby promoting more thermodynamically driven structures where the side chain compositions have greater impact. Lastly, general guidelines are presented for achieving morphological optimization via combined side chain engineering and processing additives.

36 MATERIALS SCIENCE↗

Signal Temporal Logic Control for Residential HVAC Systems to Accommodate High Solar PV Penetration

This paper proposes a new signal temporal logic (STL) control for ON/OFF residential buildings' Heating Ventilation and Air Conditioning (HVAC) systems. STL is used to control indoor temperatures while consuming most of the generated solar photovoltaic (PV) power locally to minimize its impact on the grid and reduce the need for large energy storage devices. In contrast to most, if not all, control mechanisms such as the traditional model predictive control (MPC), STL control allows for including temporal constraints in the control formulation to further relax indoor temperatures' constraints and allow them to exceed the comfort band limits for a prespecified (short) period of time. This relaxation allows to consume an additional PV power by the HVAC systems, which prevents such an unwanted intermittent power from affecting the grid. We formulate the MPC-based STL control mechanism to implement the objective. Simulation results show that the PV tracking performance has been improved while employing the proposed STL controller.

Wu, Tumin↗

Detecting surface faults on solar mirrors

Two quality control tests determine reflectivity and curvature faults of concave solar mirrors. Curvature defects in solar mirrors are easily revealed by photographing mirror surface. Calibrated aperture placed in front of camera lens admits rays reflecting only from acceptable areas of mirror, blocking out diverging rays reflected from defective areas. Defects can pinpoint problems that may exist in production. Same photograph can be obtained using calibrated disk instead of aperture, except that, this time, only defective areas would be exposed.

Argoud, M. J.↗