Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structure optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Making Activated Carbon for Storing Gas

Solid disks of microporous activated carbon, produced by a method that enables optimization of pore structure, have been investigated as means of storing gas (especially hydrogen for use as a fuel) at relatively low pressure through adsorption on pore surfaces. For hydrogen and other gases of practical interest, a narrow distribution of pore sizes <2 nm is preferable. The present method is a variant of a previously patented method of cyclic chemisorption and desorption in which a piece of carbon is alternately (1) heated to the lower of two elevated temperatures in air or other oxidizing gas, causing the formation of stable carbon/oxygen surface complexes; then (2) heated to the higher of the two elevated temperatures in flowing helium or other inert gas, causing the desorption of the surface complexes in the form of carbon monoxide. In the present method, pore structure is optimized partly by heating to a temperature of 1,100 C during carbonization. Another aspect of the method exploits the finding that for each gas-storage pressure, gas-storage capacity can be maximized by burning off a specific proportion (typically between 10 and 20 weight percent) of the carbon during the cyclic chemisorption/desorption process.

Wojtowicz, Marek A.↗
NASA NTRS1979

Weight optimization of ultra large space structures

The paper describes the optimization of a solar power satellite structure for minimum mass and system cost. The solar power satellite is an ultra large low frequency and lightly damped space structure; derivation of its structural design requirements required accommodation of gravity gradient torques which impose primary loads, life up to 100 years in the rigorous geosynchronous orbit radiation environment, and prevention of continuous wave motion in a solar array blanket suspended from a huge, lightly damped structure subject to periodic excitations. The satellite structural design required a parametric study of structural configurations and consideration of the fabrication and assembly techniques, which resulted in a final structure which met all requirements at a structural mass fraction of 10%.

Reinert, R. P.↗
NASA NTRS1990

Computer implementation of analysis and optimization procedures for control-structure interaction problems

Implementation aspects of control-structure interaction analysis and optimization by the staggered use of single-discipline analysis modules are discussed. The single-discipline modules include structural analysis, controller synthesis and optimization. The software modularity is maintained by employing a partitioned control-structure interaction analysis procedure, thus avoiding the need for embedding the single-discipline modules into a monolithic program. A software testbed has been constructed as a stand-alone analysis and optimization program and tested for its versatility and software modularity by applying it to the dynamic analysis and preliminary design of a prototype Earth Pointing Satellite. Experience with the in-core testbed program so far demonstrates that the testbed is efficient, preserves software modularity, and enables the analyst to choose a different set of algorithms, control strategies and design parameters via user software interfaces. Thus, the present software architecture is recommended for adoption by control-structure interaction analysts as a preliminary analysis and design tool.

Belvin, W. Keith↗
NASA NTRS1993

Optimization for efficient structure-control systems

The efficiency of a structure-control system is a nondimensional parameter which indicates the fraction of the total control power expended usefully in controlling a finite-dimensional system. The balance of control power is wasted on the truncated dynamics serving no useful purpose towards the control objectives. Recently, it has been demonstrated that the concept of efficiency can be used to address a number of control issues encountered in the control of dynamic systems such as the spillover effects, selection of a good input configuration and obtaining reduced order control models. Reference (1) introduced the concept and presented analyses of several Linear Quadratic Regulator designs on the basis of their efficiencies. Encouraged by the results of Ref. (1), Ref. (2) introduces an efficiency modal analysis of a structure-control system which gives an internal characterization of the controller design and establishes the link between the control design and the initial disturbances to affect efficient structure-control system designs. The efficiency modal analysis leads to identification of principal controller directions (or controller modes) distinct from the structural natural modes. Thus ultimately, many issues of the structure-control system revolve around the idea of insuring compatibility of the structural modes and the controller modes with each other, the better the match the higher the efficiency. A key feature in controlling a reduced order model of a high dimensional (or infinity-dimensional distributed parameter system) structural dynamic system must be to achieve high efficiency of the control system while satisfying the control objectives and/or constraints. Formally, this can be achieved by designing the control system and structural parameters simultaneously within an optimization framework. The subject of this paper is to present such a design procedure.

Oz, Hayrani↗
NASA NTRS1991

Multidisciplinary optimization of controlled space structures with global sensitivity equations

A new method for the preliminary design of controlled space structures is presented. The method coordinates standard finite element structural analysis, multivariable controls, and nonlinear programming codes and allows simultaneous optimization of the structures and control systems of a spacecraft. Global sensitivity equations are a key feature of this method. The preliminary design of a generic geostationary platform is used to demonstrate the multidisciplinary optimization method. Fifteen design variables are used to optimize truss member sizes and feedback gain values. The goal is to reduce the total mass of the structure and the vibration control system while satisfying constraints on vibration decay rate. Incorporating the nonnegligible mass of actuators causes an essential coupling between structural design variables and control design variables. The solution of the demonstration problem is an important step toward a comprehensive preliminary design capability for structures and control systems. Use of global sensitivity equations helps solve optimization problems that have a large number of design variables and a high degree of coupling between disciplines.

Padula, Sharon L.↗
NASA NTRS1987

Efficient optimization of integrated aerodynamic-structural design

The introduction of composite materials is having a profound effect on the design process. Because these materials permit the designer to tailor material properties to improve structural, aerodynamic and acoustic performance, they require a more integrated multidisciplinary design process. Because of the complexity of the design process numerical optimization methods are required. The present paper is focused on a major difficulty associated with the multidisciplinary design optimization process - its enormous computational cost. We consider two approaches for reducing this computational burden: (1) development of efficient methods for cross-sensitivity calculation using perturbation methods; and (2) the use of approximate numerical optimization procedures. Our efforts are concentrated upon combined aerodynamic-structural optimization. Results are presented for the integrated design of a sailplane wing. The impact of our computational procedures on the computational costs of integrated costs of integrated designs are discussed.

Haftka, R. T.↗
NASA NTRSDate not supplied

Application of a Rapid Design Tool to a 3D Woven Structural Joint

The optimization of composite structural joints is an iterative process and a multiscale problem. High fidelity finite element modeling of joints with 3D woven and laminated materials can become computationally expensive. The aim of this paper is to establish a reliable analysis process for the optimization of a composite Y-joint (curved Pi-joint), to be used in an aircraft fuselage, using commercial rapid joint design, analysis, and optimization software. The rapid joint design tool was investigated as a substitute and/or complement to a finite element analysis software. A composite Pi-joint and a composite Y-joint were evaluated using the rapid joint design tool to determine the applicability and limits of the software. Furthermore, three main preliminary parametric studies were performed to better understand the capability of the tool in predicting the stress distributions and trends in the Y-joint. The parameters investigated were the joint curvature, the laminated skin thickness, the adhesive systems, and the ply composition. Lastly, trends in predicted failure load were produced as a function of skin thickness (16ply, 24ply and 32ply). Failure loads were found with varying joint curvature and skin thickness using stress-based adherend failure criterion. The rapid joint design tool was also validated against existing experimental results.

Bonded Joints↗
NASA NTRS1988

Optimization of helicopter airframe structures for vibration reduction considerations, formulations and applications

Several key issues involved in the application of formal optimization technique to helicopter airframe structures for vibration reduction are addressed. Considerations which are important in the optimization of real airframe structures are discussed. Considerations necessary to establish relevant set of design variables, constraints and objectives which are appropriate to conceptual, preliminary, detailed design, ground and flight test phases of airframe design are discussed. A methodology is suggested for optimization of airframes in various phases of design. Optimization formulations that are unique to helicopter airframes are described and expressions for vibration related functions are derived. Using a recently developed computer code, the optimization of a Bell AH-1G helicopter airframe is demonstrated.

Murthy, T. Sreekanta↗
NASA NTRS1986

Synthesis of control laws for optimally designed large space structures

In this study, the vibration control of large space structures using the linear quadratic regulator technique is investigated. Emphasis is made on the control of both optimally designed structures and also the original (uniform) structures using the cantilever beam as an example. The open loop and closed loop eigenvalues are compared and the transient responses are obtained to determine the effectiveness of the control system design.

Satyanarayana, K.↗
NASA NTRS2001

Structures for the 3rd Generation Reusable Concept Vehicle

A major goal of NASA is to create an advance space transportation system that provides a safe, affordable highway through the air and into space. The long-term plans are to reduce the risk of crew loss to 1 in 1,000,000 missions and reduce the cost of Low-Earth Orbit by a factor of 100 from today's costs. A third generation reusable concept vehicle (RCV) was developed to assess technologies required to meet NASA's space access goals. The vehicle will launch from Cape Kennedy carrying a 25,000 lb. payload to the International Space Station (ISS). The system is an air breathing launch vehicle (ABLV) hypersonic lifting body with rockets and uses triple point hydrogen and liquid oxygen propellant. The focus of this paper is on the structural concepts and analysis methods used in developing the third generation reusable launch vehicle (RLV). Member sizes, concepts and material selections will be discussed as well as analysis methods used in optimizing the structure. Analysis based on the HyperSizer structural sizing software will be discussed. Design trades required to optimize structural weight will be presented.

Hrinda, Glenn A.↗
NASA NTRS1990

Optimal glass-ceramic structures: Components of giant mirror telescopes

Detailed investigations are carried out on optimal glass-ceramic mirror structures of terrestrial space technology (optical telescopes). In order to find an optimum design, a nonlinear multi-criteria optimization problem is formulated. 'Minimum deformation' at 'minimum weight' are selected as contradictory objectives, and a set of further constraints (quilting effect, optical faults etc.) is defined and included. A special result of the investigations is described.

Eschenauer, Hans A.↗
NASA NTRS1993

Optimal placement of tuning masses on truss structures by genetic algorithms

Optimal placement of tuning masses, actuators and other peripherals on large space structures is a combinatorial optimization problem. This paper surveys several techniques for solving this problem. The genetic algorithm approach to the solution of the placement problem is described in detail. An example of minimizing the difference between the two lowest frequencies of a laboratory truss by adding tuning masses is used for demonstrating some of the advantages of genetic algorithms. The relative efficiencies of different codings are compared using the results of a large number of optimization runs.

Ponslet, Eric↗
NASA NTRS1988

Approximation theory for LQG (Linear-Quadratic-Gaussian) optimal control of flexible structures

An approximation theory is presented for the LQG (Linear-Quadratic-Gaussian) optimal control problem for flexible structures whose distributed models have bounded input and output operators. The main purpose of the theory is to guide the design of finite dimensional compensators that approximate closely the optimal compensator. The optimal LQG problem separates into an optimal linear-quadratic regulator problem and an optimal state estimation problem. The solution of the former problem lies in the solution to an infinite dimensional Riccati operator equation. The approximation scheme approximates the infinite dimensional LQG problem with a sequence of finite dimensional LQG problems defined for a sequence of finite dimensional, usually finite element or modal, approximations of the distributed model of the structure. Two Riccati matrix equations determine the solution to each approximating problem. The finite dimensional equations for numerical approximation are developed, including formulas for converting matrix control and estimator gains to their functional representation to allow comparison of gains based on different orders of approximation. Convergence of the approximating control and estimator gains and of the corresponding finite dimensional compensators is studied. Also, convergence and stability of the closed-loop systems produced with the finite dimensional compensators are discussed. The convergence theory is based on the convergence of the solutions of the finite dimensional Riccati equations to the solutions of the infinite dimensional Riccati equations. A numerical example with a flexible beam, a rotating rigid body, and a lumped mass is given.

Gibson, J. S.↗
NASA NTRS1989

Algorithm For Optimal Control Of Large Structures

Cost of computation appears competitive with other methods. Problem to compute optimal control of forced response of structure with n degrees of freedom identified in terms of smaller number, r, of vibrational modes. Article begins with Hamilton-Jacobi formulation of mechanics and use of quadratic cost functional. Complexity reduced by alternative approach in which quadratic cost functional expressed in terms of control variables only. Leads to iterative solution of second-order time-integral matrix Volterra equation of second kind containing optimal control vector. Cost of algorithm, measured in terms of number of computations required, is of order of, or less than, cost of prior algoritms applied to similar problems.

Salama, Moktar A.↗
NASA NTRS1992

Optimum design of high speed prop rotors including the coupling of performance, aeroelastic stability and structures

An optimization procedure is developed for the design of high speed prop-rotors to be used in civil tiltrotor applications. The goal is to couple aerodynamic performance, aeroelastic stability, and structural design requirements inside a closed-loop optimization procedure. The objective is to minimize the gross weight and maximize the propulsive efficiency in high speed cruise. Constraints are imposed on the rotor aeroelastic stability in both hover and cruise and rotor figure of merit in hover. Both structural and aerodynamic design variables are used.

Chattopadhyay, Aditi↗
NASA NTRS1984

Role of optimization in interdisciplinary analyses of naval structures

The need for numerical design optimization of naval structures is discussed. The complexity of problems that arise due to the significant roles played by three major disciplines, i.e., structural mechanics, acoustics, and hydrodynamics are discussed. A major computer software effort that has recently begun at the David W. Taylor Naval Ship R&D Center to accommodate large multidisciplinary analyses is also described. In addition to primarily facilitating, via the use of data bases, interdisciplinary analyses for predicting the response of the Navy's ships and related structures, this software effort is expected to provide the analyst with a convenient numerical workbench for performing large numbers of analyses that may be necessary for optimizing the design performance. Finally, an example is included that investigates several aspects of optimizing a typical naval structure from the viewpoints of strength, hydrodynamic form, and acoustic characteristics.

Dhir, S. K.↗
NASA NTRS1986

Application of mathematical optimization procedures to a structural model of a large finite-element wing

An optimization system is described that consists of the finite-element analysis program known as Engineering Analysis Language (EAL), the CONMIN optimization program, and a piecewise linear analysis. The optimization analysis system (OPTEAL) is used to minimize the mass of a transport wing subject to stress constraints for two static load conditions. The optimization procedure and the optimization analysis system (OPTEAL) are described and the optiomized results with fully stressed design results compared.

Walsh, J. L.↗