Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface Engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

The effect of insulated combustion chamber surfaces on direct-injected diesel engine performance, emissions, and combustion

The combustion chamber of a single-cylinder, direct-injected diesel engine was insulated with ceramic coatings to determine the effect of low heat rejection (LHR) operation on engine performance, emissions, and combustion. In comparison to the baseline cooled engine, the LHR engine had lower thermal efficiency, with higher smoke, particulate, and full load carbon monoxide emissions. The unburned hydrocarbon emissions were reduced across the load range. The nitrous oxide emissions increased at some part-load conditions and were reduced slightly at full loads. The poor LHR engine performance was attributed to degraded combustion characterized by less premixed burning, lower heat release rates, and longer combustion duration compared to the baseline cooled engine.

Dickey, Daniel W.↗

Nanoparticle Surface Passivation Strategies to Improve the Cycle and Calendar Lifetime of Silicon Anodes in Standard Carbonate Electrolytes

Silicon Lithium alloys (SiLix) as the anode active material in a Li-Ion battery configuration offer possible energy densities paralleled only by pure lithium metal. However, the extreme mechanical deformation of alloying and dealloying SiLix through charge/discharge cycles paired with the highly reactive interface of SiLix which generates an interfacial layer known as the solid-electrolyte-interphase are large barriers to industrial adoption of high-silicon-content negative electrodes. Moreover, these challenges are magnified when the thickness of the electrode is brought to relevant levels (>3 mg/cm2). Here, I describe our efforts to address these challenges by utilizing single-nanometer-scale silicon nanoparticles to reduce capacity fade related to mechanical failure. I also detail our efforts to modify the silicon surface through interfacial chemical engineering strategies to passivate the silicon surface. This development three different majority silicon electrodes (50-74 wt%) to achieve cycle capacity retention of greater than 73% through 1000 charge/discharge cycles against capacity-matched NMC-based cathodes and calendar lifetimes greater than one year. This research is a part of the multi-national lab Silicon Consortium Project.

anodes↗

Plasma-assisted physical vapor deposition surface treatments for tribological control

In any mechanical or engineering system where contacting surfaces are in relative motion, adhesion, wear, and friction affect reliability and performance. With the advancement of space age transportation systems, the tribological requirements have dramatically increased. This is due to the optimized design, precision tolerance requirements, and high reliability expected for solid lubricating films in order to withstand hostile operating conditions (vacuum, high-low temperatures, high loads, and space radiation). For these problem areas the ion-assisted deposition/modification processes (plasma-based and ion beam techniques) offer the greatest potential for the synthesis of thin films and the tailoring of adherence and chemical and structural properties for optimized tribological performance. The present practices and new approaches of applying soft solid lubricant and hard wear resistant films to engineering substrates are reviewed. The ion bombardment treatments have increased film adherence, lowered friction coefficients, and enhanced wear life of the solid lubricating films such as the dichalcogenides (MoS2) and the soft metals (Au, Ag, Pb). Currently, sputtering is the preferred method of applying MoS2 films; and ion plating, the soft metallic films. Ultralow friction coefficients (less than 0.01) were achieved with sputtered MoS2. Further, new diamond-like carbon and BN lubricating films are being developed by using the ion assisted deposition techniques.

Spalvins, Talivaldis↗

Fourier-method beam analysis for coherent vertical cavity surface emitting laser arrays

Effective engineering and exploitation of coherently coupled vertical cavity surface emitting laser arrays will benefit from simple and fast characterization of the optical coupling and coherence. We propose a Fourier method of analyzing beam profiles as an alternative to the prior beam visibility analysis and show that the mode suppression ratio and phase between a pair of supermodes can be extracted. Our analysis enables fast quantitative determination of the array coherence and supermode characteristics.

Strzebonski, Pawel (ORCID:0000000156286296)↗

Wind tunnel investigation of a large-scale upper surface blown-flap transport model having two engines

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an upper surface blowing flap system that would augment lift. The model had a 25 deg swept wing of aspect ratio 7.89 and two turbofan engines with the engine centerline located at 0.256 of the wing semispan. The lift of the flap system was augmented by turbofan exhaust impingement on the Coanda surface. Results were obtained for several flap deflections and engine nozzle configurations at jet momentum coefficients from 0 to 4.0. Three-component longitudinal data are presented with two engines operating. Limited longitudinal and lateral data are presented with an engine out. In addition, limited exhaust and flap pressure data are presented.

Aoyagi, K.↗

Strain Engineering: Reduction of Microstrain at the Perovskite Surface via Alkali Metal Chloride Treatment Enhances Stability

Degradation of halide perovskites under a humid atmosphere is the major challenge preventing widespread commercial deployment of this material class. Here it is shown that strain engineering via alkali metal chloride treatment at the FAPbI 3 /SnO 2 interface effectively improves moisture-related stability. CsCl and KCl treatments reduce microstrain at the perovskite surface and slow the α- to δ-phase transformation. Alkali metal treatments with LiCl, NaCl, and RbCl led to an increase in microstrain and faster degradation. The compressive strain at the perovskite surface was the smallest for CsCl and was linked to improved stability. First-principles density functional theory calculations confirm the preferential formation of alkali defects at interstitial positions at the perovskite surface. Particularly CsCl and KCl treatments lead to a release of compressive strain at the perovskite surface and local structural distortions that may favor passivation of surface defects. In contrast, the room-temperature dynamics of Li interstitials result in an overall expansion of lattice volume, which may be linked to more facile lattice degradation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Low-speed wind-tunnel investigation of a large-scale advanced arrow wing supersonic transport configuration with engines mounted above the wing for upper-surface blowing

The Langley full scale tunnel was used to investigate the low speed stability and control of an advanced arrow wing supersonic transport with engines mounted above the wing for upper-surface blowing. Tests were made over an angle of attack range of -10 to 32 deg, slideslip angles of + or -5 deg and a Reynolds number ranging from 3.53 million to 7.33 million (referenced to mean aerodynamic chord of the wing). Configuration variables included trailing-edge flap deflection, engine jet nozzle angle, engine thrust coefficient, engine out operation, and asymmetrical trailing-edge BLC for providing roll trim. Downwash measurements at the tail were obtained for different thrust coefficients, tail heights, and at two fuselage stations.

Shivers, J. P.↗

Building Random Alloy Surfaces from Intermetallic Seeds: A General Route to Strain-Engineered Electrocatalysts with High Durability

Pt-based catalysts are common in fuel cells but suffer from high cost and poor durability. To overcome these limitations, earth-abundant metals are often incorporated with Pt in core@shell architectures or through alloy formation. In this work, the concepts of a core@shell architecture, alloyed surfaces, and high-durability intermetallics are integrated into one nanostructure platform using seed-mediated co-reduction (SMCR). Specifically, random alloy PtM (where M = Ni, Co, Cu, or Fe) shells are deposited on intermetallic PdCu B2 seeds. Control of shell thickness and Pt:M ratios is also demonstrated, providing a general route to strain-engineered alloyed surfaces. The performance of these nanocatalysts was evaluated for the oxygen reduction reaction (ORR) as a function of shell thickness and shell composition, where PtCu and PtNi shells showed a 230% and 270% activity increase, respectively, compared to the Pt reference. This evaluation is coupled with Tafel plot analysis which shows significant changes in the Tafel slopes, which indicate a shift in the rate-limiting step when a core@shell architecture is incorporated. Significantly, this work demonstrates the versatility of SMCR as a facile way to integrate a core@shell architecture, alloyed surfaces, and high-durability intermetallics within one platform.

36 MATERIALS SCIENCE↗

Engineering the Si Anode Interface via Particle Surface Modification: Embedded Organic Carbonates Lead to Enhanced Performance

Si nanoparticles (SiNPs) are recognized as a promising anode material for next-generation high-energy lithium-ion batteries. However, due to the more stringent requirements resulting from severe volume change, the solid-electrolyte interphase (SEI) on SiNPs plays a critical role in determining their cycling performance. Engineering the interface for higher stability has become an effective yet challenging approach to accommodate the deterioration of the silicon anode from the repeated lithiation/delithiation process. Herein, we report a novel approach of engineering a covalently bonded organic monolayer of ethylene carbonates onto the surface of the SiNPs that can help form a sturdy SEI. Finally, this molecule-level surface modification provides an effective approach to enable high-energy lithium-ion batteries with Si anodes.

25 ENERGY STORAGE↗

Epitaxial graphene-encapsulated surface reconstruction of Ge(110)

Understanding and engineering the properties of crystalline surfaces has been critical in achieving functional electronics at the nanoscale. Employing scanning tunneling microscopy, surface x-ray diffraction, and high-resolution x-ray reflectivity experiments, we present a thorough study of epitaxial graphene (EG)/Ge(110) and report a Ge(110) "6 x 2" reconstruction stabilized by the presence of epitaxial graphene unseen in group-IV semiconductor surfaces. As a result, X-ray studies reveal that graphene resides atop the surface reconstruction with a 0.34 nm van der Waals (vdW) gap and provides protection from ambient degradation.

36 MATERIALS SCIENCE↗

Measurement of local high-level, transient surface heat flux

This study is part of a continuing investigation to develop methods for measuring local transient surface heat flux. A method is presented for simultaneous measurements of dual heat fluxes at a surface location by considering the heat flux as a separate function of heat stored and heat conducted within a heat flux gage. Surface heat flux information is obtained from transient temperature measurements taken at points within the gage. Heat flux was determined over a range of 4 to 22 MW/sq m. It was concluded that the method is feasible. Possible applications are for heat flux measurements on the turbine blade surfaces of space shuttle main engine turbopumps and on the component surfaces of rocket and advanced gas turbine engines and for testing sensors in heat flux gage calibrators.

Liebert, Curt H.↗

Ultrafast all-optical switching and error-free 10 Gbit/s wavelength conversion in hybrid InP-silicon on insulator nanocavities using surface quantum wells

Ultrafast switching with low energies is demonstrated using InP photonic crystal nanocavities embedding InGaAs surface quantum wells heterogeneously integrated to a silicon on insulator waveguide circuitry. Thanks to the engineered enhancement of surface non radiative recombination of carriers, switching time is obtained to be as fast as 10 ps. These hybrid nanostructures are shown to be capable of achieving systems level performance by demonstrating error free wavelength conversion at 10 Gbit/s with 6 mW switching powers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗