Search NASA⌕ Search

SEARCH · Search NASA

Results for “THRUST PROGRAMMING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Core/Combustor-Noise Baseline Measurements for the DGEN Aeropropulsion Research Turbofan

Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and advances in mitigation of other noise sources. Future propulsion systems for ultra-efficient commercial air vehicles are projected to be of increasingly higher bypass ratio from larger fans combined with much smaller cores, with ultra-clean burning fuel-flexible combustors. Unless effective noise-reduction strategies are developed, combustor noise is likely to become a prominent contributor to overall airport community noise in the future. The new NASA DGEN Aeropropulsion Research Turbofan (DART) is a cost-efficient testbed for the study of core-noise physics and mitigation. This paper describes the recently completed DART core/combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). Acoustic data were simultaneously acquired using the AAPL overhead microphone array in the engine aft quadrant farfield, a single midfield microphone, and two semi-infinite-tube unsteady pressure sensors at the core-nozzle exit. Combustor-noise components of measured total-noise signatures were educed using a two-signal source-separation method and are found to occur in the expected frequency range. The acoustic data compare well with results from a limited 2014 feasibility test and will serve as a high-quality baseline for future research using the DART. The research described herein is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject.

Turbomachinery Noise↗
NASA NTRS2018

Core/Combustor-Noise Baseline Measurements for the DGEN Aeropropulsion Research Turbofan

Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and advances in mitigation of other noise sources. Future propulsion systems for ultra-efficient commercial air vehicles are projected to be of increasingly higher bypass ratio from larger fans combined with much smaller cores, with ultra-clean burning fuel-flexible combustors. Unless effective noise-eduction strategies are developed, combustor noise is likely to become a prominent contributor to overall airport community noise in the future. The new NASA DGEN Aeropropulsion Research Turbofan (DART) is a cost-efficient testbed for the study of core-noise physics and mitigation. This paper describes the recently completed DART core/combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). Acoustic data was simultaneously acquired using the AAPL overhead microphone array in the engine aft quadrant far field, a single midfield microphone, and two semi-infinite-tube unsteady pressure sensors at the core-nozzle exit. Combustor-noise components of measured total-noise signatures were educed using a two-signal source-separation method and are found to occur in the expected frequency range. The acoustic data compares well with results from a limited 2014 feasibility test and will serve as a high-quality baseline for future research using the DART. The research described herein is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject.

Aeroacoustics↗
NASA NTRS2018

Core/Combustor-Noise Update

Future propulsion systems for ultra-efficient commercial air vehicles are projected to be of increasingly higher bypass ratios resulting from larger fans combined with much smaller cores, with ultra-clean burning fuel-flexible combustors. Unless effective noise-reduction strategies are developed, combustor noise is likely to become a prominent contributor to overall airport community noise in the future. This presentation gives a brief overview of the NASA outlook on pertinent issues and far-term research needs as well as current and planned research in the core/combustor-noise area. The research described herein is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject. The overarching goal of the Advanced Air Transport Technology (AATT) Project is to explore and develop technologies and concepts to revolutionize the energy efficiency and environmental compatibility of fixed wing transport aircrafts. These technological solutions are critical in reducing the impact of aviation on the environment even as this industry and the corresponding global transportation system continue to grow.

Hultgren, Lennart S.↗
NASA NTRS1998

Elimination of High-Frequency Combustion Instability in the Fastrac Engine Thrust Chamber

NASA's Marshall Space Flight Center(MSFC) has been tasked with developing a 60,000 pound thrust, pump-fed, LOX/RP-1 engine under the Advanced Space Transportation Program(ASTP). This government-led design has been designated the Fastrac engine. The X-34 vehicle will use the Fastrac engine as the main propulsion system. The X-34 will be a suborbital vehicle developed by the Orbital Sciences Corporation. The X-34 vehicle will be launched from an L-1011 airliner. After launch, the X-34 vehicle will be able to climb to altitudes up to 250,000 feet and reach speeds up to Mach 8, over a mission range of 500 miles. The overall length, wingspan, and gross takeoff weight of the X-34 vehicle are 58.3 feet, 27.7 feet and 45,000 pounds, respectively. This report summarizes the plan of achieving a Fastrac thrust chamber assembly(TCA) stable bomb test that meets the JANNAF standards, the Fastrac TCA design, and the combustion instabilities exhibited by the Fastrac TCA during testing at MSFC's test stand 116 as determined from high-frequency fluctuating pressure measurements. This report also summarizes the characterization of the combustion instabilities from the pressure measurements and the steps taken to eliminate the instabilities.

Rocker, Marvin↗
NASA NTRS1977

Propeller design by numerical optimization

A computer program designed to optimize propeller characteristics was developed by combining two main programs: the first is the optimization program based on the gradient algorithm; the second is based on a propeller blade element theory and uses an aerodynamics subprogram to approximate the lift and drag characteristics of the NACA 16-series airfoil section. To evaluate the propeller program alone (with its aerodynamics subprogram), propeller characteristics were computed and compared to those from wind tunnel investigations conducted on three different NACA propellers. Although the thrust and power coefficients which were computed using the blade element theory were generally higher than the experimental results for two of the three propellers, the corresponding efficiencies showed good agreement for all three propellers. The propeller optimization program was then used to study the NACA 4-(5)(08)-03 propeller at various Mach numbers from 0.175 to 0.60. Improvements in propeller efficiency and thrust were obtained through the use of the propeller optimization program.

Mendoza, J. P.↗
NASA NTRS1972

A Monte Carlo error analysis program for near-Mars, finite-burn, orbital transfer maneuvers

A computer program was developed which performs an error analysis of a minimum-fuel, finite-thrust, transfer maneuver between two Keplerian orbits in the vicinity of Mars. The method of analysis is the Monte Carlo approach where each off-nominal initial orbit is targeted to the desired final orbit. The errors in the initial orbit are described by two covariance matrices of state deviations and tracking errors. The function of the program is to relate these errors to the resulting errors in the final orbit. The equations of motion for the transfer trajectory are those of a spacecraft maneuvering with constant thrust and mass-flow rate in the neighborhood of a single body. The thrust vector is allowed to rotate in a plane with a constant pitch rate. The transfer trajectory is characterized by six control parameters and the final orbit is defined, or partially defined, by the desired target parameters. The program is applicable to the deboost maneuver (hyperbola to ellipse), orbital trim maneuver (ellipse to ellipse), fly-by maneuver (hyperbola to hyperbola), escape maneuvers (ellipse to hyperbola), and deorbit maneuver.

Green, R. N.↗
NASA NTRS1989

Hybrid propulsion technology program: Phase 1, volume 2

The program objectives of developing hybrid propulsion technology (HPT) to enable its application for manned and unmanned high thrust, high performance space launch vehicles are examined. The studies indicate that the hybrid propulsion (HP) is very attractive, especially when applied to large boosters for programs such as the Advanced Launch System (ALS) and the second generation Space Shuttle. Some of the advantages of HP are identified. Space launch vehicles using HP are less costly than those flying today because their propellant and insulation costs are much less and there are fewer operational restraints due to reduced safety requirements. Boosters using HP have safety features that are highly desirable, particularly for manned flights. HP systems will have a clean exhaust and high performance. Boosters using HP readily integrate with launch vehicles and their launch operations, because they are very compact for the amount of energy contained. Hybrid propulsion will increase the probability of mission success. In order to properly develop the technologies of HP, preliminary HP concepts are evaluated. System analyses and trade studies were performed to identify technologies applicable to HP.

Schuler, A. L.↗
NASA NTRS1972

Maximum noise abatement trajectories.

Minimum noise annoyance trajectories for developing STOL operation procedures are obtained by modulating five control variables in two dimensions. The performance index is formulated such that it explicitly assigns the same relative importance to thrust as it does to distances between discrete listeners and the aircraft. However, using a steepest descent optimization program, results indicate that it is preferable to keep the thrusters at their maximum value to minimize the integrated annoyance rather than to reduce thrust which would lower the instantaneous annoyance. Thrust decreases below its bound only when the instantaneous noise at a listener is limited.

Zeldin, S.↗
NASA NTRS1974

MSFC's utilization of existing design technology in the Skylab program

In the design of Skylab use was made in a number of cases of technological experience obtained in connection with earlier phases of the space program. In the development of the payload shroud use was made of Saturn V flight data. The shroud thrusting joint system was an adaptation of a system flown on the Titan IIIC. Scientific airlock hardware for Skylab was available from the Apollo Program. The design of the Orbital Workshop was based on the technology base provided by Saturn programs. Details regarding the repair tools used for correcting orbital workshop meteoroid shield/solar array anomalies which occurred during the ascent are discussed along with a commercial concept for coolant resupply, giving attention to aid provided by already existing technological developments.

Eudy, R. G.↗
NASA NTRS1990

Hybrid Propulsion Technology Program

Future launch systems of the United States will require improvements in booster safety, reliability, and cost. In order to increase payload capabilities, performance improvements are also desirable. The hybrid rocket motor (HRM) offers the potential for improvements in all of these areas. The designs are presented for two sizes of hybrid boosters, a large 4.57 m (180 in.) diameter booster duplicating the Advanced Solid Rocket Motor (ASRM) vacuum thrust-time profile and smaller 2.44 m (96 in.), one-quater thrust level booster. The large booster would be used in tandem, while eight small boosters would be used to achieve the same total thrust. These preliminary designs were generated as part of the NASA Hybrid Propulsion Technology Program. This program is the first phase of an eventual three-phaes program culminating in the demonstration of a large subscale engine. The initial trade and sizing studies resulted in preferred motor diameters, operating pressures, nozzle geometry, and fuel grain systems for both the large and small boosters. The data were then used for specific performance predictions in terms of payload and the definition and selection of the requirements for the major components: the oxidizer feed system, nozzle, and thrust vector system. All of the parametric studies were performed using realistic fuel regression models based upon specific experimental data.

Jensen, G. E.↗
NASA NTRS2005

F119 Nozzle Flaps Tested at Lewis' CE-22 Facility

The next generation of aircraft fighters requires higher engine performance and enhanced stealth characteristics for air superiority. A Lockheed-Martin/Boeing aircraft with a Pratt & Whitney F119 engine was selected by the Air Force for the next advanced tactical fighter (ATF). As part of this program, the NASA Lewis Research Center entered into a cooperative test program with Pratt & Whitney along with the Air Force to study the performance for various advanced nozzle concepts for the F119 engine. The area of interest was to measure the internal performance (both thrust and flow coefficients) of nozzle flaps redesigned for low observability with minimal performance loss. The experimental program was successfully completed May 1995 in Lewis' CE-22 facility. The models were tested over a wide range of geometric variations and nozzle pressure ratios. Results confirmed that the redesigned nozzle flaps had an insignificant effect on the thrust performance and that the resulting flow patterns should not be a problem in the cooling flow design. The results also agreed well with Pratt & Whitney's computational fluid dynamics analysis. The data obtained from this test were added to the current data base to help validate other performance prediction methodology.

Source record↗
NASA NTRS1990

Challenging the Future - Journey to Excellence. Aeropropulsion strategic plan for the 1990's

Over the past several months, the Lewis Aeropropulsion Management Council (AMC) has conducted a critical assessment of its strategic plan. This assessment clearly indicated a need for change, both in the aeropropulsion program emphasis and in the approach to carrying out that program. Customers sent a strong message that the program must improve the timeliness of research and technology products and services and must work more closely with them to develop and transfer new technology. The strategic plan defines AMC's vision for the future and underlying organizational values. It contains a set of broad strategies and actions that point the way toward achieving the goals of customer satisfaction, organizational effectiveness, and programmatic excellence. Those strategies are expected to form the basis for the development of specific tactical plans by Lewis aeropropulsion thrust teams, divisions, and branches. To guide tactical planning of the aeropropulsion program, this strategic plan outlines the agency's strategic directions and long-range aeronautics goals, the aeropropulsion goals and key objectives for achieving them, projections of Lewis aeropropulsion budgets, planned allocations of resources, and the processes that will be used to measure success in carrying out the strategic plan.

Source record↗
NASA NTRS2014

Range Safety Flight Elevation Limit Calculation Software

This program was developed to fill a need within the Wallops Flight Facility workflow for automation of the development of vertical plan limit lines used by flight safety officers during the conduct of expendable launch vehicle missions. Vertical plane present-position-based destruct lines have been used by range safety organizations at numerous launch ranges to mitigate launch vehicle risks during the early phase of flight. Various ranges have implemented data submittal and processing workflows to develop these destruct lines. As such, there is significant prior art in this field. The ElLimits program was developed at NASA's Wallops Flight Facility to automate the process for developing vertical plane limit lines using current computing technologies. The ElLimits program is used to configure launch-phase range safety flight control lines for guided missiles. The name of the program derives itself from the fundamental quantity that is computed - flight elevation limits. The user specifies the extent and resolution of a grid in the vertical plane oriented along the launch azimuth. At each grid point, the program computes the maximum velocity vector flight elevation that can be permitted without endangering a specified back-range location. Vertical plane x-y limit lines that can be utilized on a present position display are derived from the flight elevation limit data by numerically propagating 'streamlines' through the grid. The failure turn and debris propagation simulation technique used by the application is common to all of its analysis options. A simulation is initialized at a vertical plane grid point chosen by the program. A powered flight failure turn is then propagated in the plane for the duration of the so-called RSO reaction time. At the end of the turn, a delta-velocity is imparted, and a ballistic trajectory is propagated to impact. While the program possesses capability for powered flight failure turn modeling, it does not require extensive user inputs of vehicle characteristics (e.g., thrust and aerodynamic data), nor does it require reams of turn data after the traditional fashion of the Air Force ranges. The program requires a nominal trajectory table (time, altitude, range, velocity, and flight elevation) and makes heavy use of it to initialize and model a failure turn.

Lanzi, Raymond J↗
NASA NTRS1989

NASA/USRA advanced space design program: The laser powered interorbital vehicle

A preliminary design is presented for a low-thrust Laser Powered Interorbital Vehicle (LPIV) intended for cargo transportation between an earth space station and a lunar base. The LPIV receives its power from two iodide laser stations, one orbiting the earth and the other located on the surface of the moon. The selected mission utilizes a spiral trajectory, characteristic of a low-thrust spacecraft, requiring 8 days for a lunar rendezvous and an additional 9 days for return. The ship's configuration consists primarily of an optical train, two hydrogen plasma engines, a 37.1 m box beam truss, a payload module, and fuel tanks. The total mass of the vehicle fully loaded is 63300 kg. A single plasma, regeneratively cooled engine design is incorporated into the two 500 N engines. These are connected to the spacecraft by turntables which allow the vehicle to thrust tangentially to the flight path. Proper collection and transmission of the laser beam to the thrust chambers is provided through the optical train. This system consists of the 23 m diameter primary mirror, a convex parabolic secondary mirror, a beam splitter and two concave parabolic tertiary mirrors. The payload bay is capable of carrying 18000 kg of cargo. The module is located opposite the primary mirror on the main truss. Fuel tanks carrying a maximum of 35000 kg of liquid hydrogen are fastened to tracks which allow the tanks to be moved perpendicular to the main truss. This capability is required to prevent the center of mass from moving out of the thrust vector line. The laser beam is located and tracked by means of an acquisition, pointing and tracking system which can be locked onto the space-based laser station. Correct orientation of the spacecraft with the laser beam is maintained by control moment gyros and reaction control rockets. Additionally an aerobrake configuration was designed to provide the option of using the atmospheric drag in place of propulsion for a return trajectory.

Source record↗
NASA NTRS1973

Noise and wake structure measurements in a subsonic tip speed fan

The results of an experimental program are reported which show the effect of blade angle, tip speed, fan pressure ratio, and thrust on noise of a model fan of 0.457m (18 inches) diameter operating at subsonic tip speeds at pressure ratios between 1.06 and 1.15. The fan used in this study had 12 blades, 7 stator vanes, and a spacing between the rotor and stator of 1.85 blade chords. This fan was originally designed for aerodynamic testing and was considered a good performer. It was used in the noise test program as it incorporated features found to reduce noise in an earlier analytical parametric study. For a given pressure ratio the fan was shown to exhibit minimum noise at the blade angle and tip speed near that of maximum aerodynamic efficiency. Also, the noise level and spectrum character of this fan showed excellent correlation with scaled data of a similar larger diameter fan. Results of the program confirm the trends shown in the earlier analytical parametric study which showed that fan noise could be reduced for a given thrust and pressure ratio by increasing fan solidity, improving fan aerodynamic design, and operating the fan at an optimum subsonic tip speed. In addition to noise, the blade wake characteristics at the leading edge of the stator were measured in this program. At root and tip sections some difference between predicted and measured wakes was found. However comparisons between predicted and measured wakes at mid span locations was found to be good.

Magliozzi, B.↗
NASA NTRS1982

Thrust-induced effects on low-speed aerodynamics of fighter aircraft

Results of NASA Langley has conducted wind-tunnel investigations of several fighter configurations conducted to determine the effects of both thrust vectoring and spanwise blowing are reviewed. A recent joint NASA/Grumman Aerospace Corporation/U.S. Air Force Wright Aeronautical Laboratory wind-tunnel investigation was conducted to examine the effects of spanwise blowing on the trailing-edge flap system. This application contrasts with the more familiar method of spanwise blowing near the wing leading edge. Another joint program among NASA/McDonnell Aircraft Company/U.S. Air Force Wright Aeronautical Laboratory investigated the effects of reverse thrust on the low-speed aerodynamics of an F-15 configuration. The F-15 model was fitted with a rotating van thrust reverser concept which could simulate both in-flight reversing for approach and landing or full reversing for ground roll reduction. The significant results of these two joint programs are reported.

Banks, D. W.↗
NASA NTRS1992

Small Business Innovations (Helicopters)

The amount of engine power required for a helicopter to hover is an important, but difficult, consideration in helicopter design. The EHPIC program model produces converged, freely distorted wake geometries that generate accurate analysis of wake-induced downwash, allowing good predictions of rotor thrust and power requirements. Continuum Dynamics, Inc., the Small Business Innovation Research (SBIR) company that developed EHPIC, also produces RotorCRAFT, a program for analysis of aerodynamic loading of helicopter blades in forward flight. Both helicopter codes have been licensed to commercial manufacturers.

Source record↗