Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transient Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Ignition transient analysis of solid rocket motor

Measurement data on the performance of Space Shuttle Solid Rocket Motor show wide variations in the head-end pressure changes and the total thrust build-up during the ignition transient periods. To analyze the flow and thermal behavior in the tested solid rocket motors, a 1-dimensional, ideal gas flow model via the SIMPLE algorithm was developed. Numerical results showed that burning patterns in the star-shaped head-end segment of the propellant and the erosive burning rate are two important factors controlling the ignition transients. The objective of this study is to extend the model to include the effects of aluminum particle commonly used in solid propellants. To treat the effects of aluminum-oxide particles in the combustion gas, conservation of mass, momentum, and energy equations for the particles are added in the numerical formulation and integrated by an inter-phase-slip algorithm.

Han, Samuel S.↗
NASA NTRS2017

Propulsion Controls Modeling for a Small Turbofan Engine

A nonlinear dynamic model and propulsion controller are developed for a small-scale turbofan engine. The small-scale turbofan engine is based on the Price Induction company's DGEN 380, one of the few turbofan engines targeted for the personal light jet category. Comparisons of the nonlinear dynamic turbofan engine model to actual DGEN 380 engine test data and a Price Induction simulation are provided. During engine transients, the nonlinear model typically agrees within 10 percent error, even though the nonlinear model was developed from limited available engine data. A gain scheduled proportional integral low speed shaft controller with limiter safety logic is created to replicate the baseline DGEN 380 controller. The new controller provides desired gain and phase margins and is verified to meet Federal Aviation Administration transient propulsion system requirements. In understanding benefits, there is a need to move beyond simulation for the demonstration of advanced control architectures and technologies by using real-time systems and hardware. The small-scale DGEN 380 provides a cost effective means to accomplish advanced controls testing on a relevant turbofan engine platform.

jet propulsion↗
NASA NTRS1980

Thermodynamic performance testing of the orbiter flash evaporator system

System level testing of the space shuttle orbiter's development flash evaporator system (FES) was performed in a thermal vacuum chamber capable of simulating ambient ascent, orbital, and entry temperature and pressure profiles. The test article included the evaporator assembly, high load and topping exhaust duct and nozzle assemblies, and feedwater supply assembly. Steady state and transient heat load, water pressure/temperature and ambient pressure/temperature profiles were imposed by especially designed supporting test hardware. Testing in 1978 verified evaporator and duct heater thermal design, determined FES performance boundaries, and assessed topping evaporator plume characteristics. Testing in 1979 combined the FES with the other systems in the orbiter active thermal control subsystem (ATCS). The FES met or exceeded all nominal and contingency performance requirements during operation with the integrated ATCS. During both tests stability problems were encountered during steady state operations which resulted in subsequent design changes to the water spray nozzle and valve plate assemblies.

Jaax, J. R.↗
NASA NTRS2010

Liquid Oxygen Propellant Densification Production and Performance Test Results With a Large-Scale Flight-Weight Propellant Tank for the X33 RLV

This paper describes in-detail a test program that was initiated at the Glenn Research Center (GRC) involving the cryogenic densification of liquid oxygen (LO2). A large scale LO2 propellant densification system rated for 200 gpm and sized for the X-33 LO2 propellant tank, was designed, fabricated and tested at the GRC. Multiple objectives of the test program included validation of LO2 production unit hardware and characterization of densifier performance at design and transient conditions. First, performance data is presented for an initial series of LO2 densifier screening and check-out tests using densified liquid nitrogen. The second series of tests show performance data collected during LO2 densifier test operations with liquid oxygen as the densified product fluid. An overview of LO2 X-33 tanking operations and load tests with the 20,000 gallon Structural Test Article (STA) are described. Tank loading testing and the thermal stratification that occurs inside of a flight-weight launch vehicle propellant tank were investigated. These operations involved a closed-loop recirculation process of LO2 flow through the densifier and then back into the STA. Finally, in excess of 200,000 gallons of densified LO2 at 120 oR was produced with the propellant densification unit during the demonstration program, an achievement that s never been done before in the realm of large-scale cryogenic tests.

Tomsik, Thomas M.↗
NASA NTRS1973

Integrated Propulsion Control System program.

Description of a three-year exploratory research program for the design, development, and flight evaluation of an Integrated Propulsion Control System (IPCS). The primary objectives of this program are to establish through flight test the potential improvements in steady-state and transient propulsion system performance that can be achieved as a direct result of new modes of control, more direct sensing of engine and inlet parameters, and the use of more sophisticated, high-speed digital computation. A F-111 E aircraft with the left inlet and engine modified to the IPCS configuration will be used to conduct the flight evaluation.

Bentz, C. E.↗
NASA NTRS1975

Space shuttle orbit maneuvering engine

Data on the performance, stability, and thermal characteristics of an OME operating with an alternate injector configuration and with alternate propellants was obtained. The design, manufacturing, and operating characteristics of an electroformed, regeneratively cooled thrust chamber were also derived. Subscale and full scale tests provide data relating to off-design and transient operation.

Pauckert, R. P.↗
NASA NTRS1979

Evaluation of improved algorithms for nonlinear transient structural heat transfer

The paper presents the evaluation of algorithms having potential for reducing computer time to integrate large systems of equations governing nonlinear transient heat transfer in complex structures. A series of test problems is being developed to test two algorithms. The Shuttle Orbiter frame model having 190 nodes was the subject of an analytical/experimental study. Plans are to perform calculations for the complete wing model having about 4000 nodes as well as a regional (plug) model having about 200 nodes.

Adelman, H. M.↗
NASA NTRS1980

Structural tests on a tile/strain isolation pad thermal protection system

The aluminum skin of the space shuttle is covered by a thermal protection system (TPS) consisting of a low density ceramic tile bonded to a matted-felt material called strain insulation pad (SIP). The structural characteristics of the TPS were studied experimentally under selected extreme load conditions. Three basic types of loads were imposed: tension, eccentrically applied tension, and combined in-plane force and transverse pressure. For some tests, transverse pressure was applied rapidly to simulate a transient shock wave passing over the tile. The failure mode for all specimens involved separation of the tile from the SIP at the silicone rubber bond interface. An eccentrically applied tension load caused the tile to separate from the SIP at loads lower than experienced at failure for pure tension loading. Moderate in-plane as well as shock loading did not cause a measurable reduction in the TPS ultimate failure strength. A strong coupling, however, was exhibited between in-plane and transverse loads and displacements.

Williams, J. G.↗
NASA NTRS1979

Design of space payloads for transient environments

Current practices used to design space payload structures for transient dynamic loads are described. Included in the discussion of the design process are the estimation of preliminary loads, development of dynamic models, calculation of transient loads, verification of analytical models, establishment of development tests, definition of the qualification tests, and acquisition of flight data. An indication of the accuracy of the analytical predictions is provided by comparing them with actual test and flight data. Many illustrations and much data obtained during the Viking Project are used to clarify the current practices.

Wada, B. K.↗
NASA NTRS1986

A procedure for calculating the damping in multi-element space structures

A procedure for analyzing the damping in a multielement space structure connected by joints is described, in which distributed material damping and discrete nonlinear joint properties are incorporated into a linear analysis. The procedure involves four steps: (1) creation of a linear undamped finite element model; (2) experimental measurements of the transient response of a truss member in free fall tests to obtain material damping properties; with these properties incorporated into a linear damped finite element model of the structure; (3) the identification of the nonlinear joint properties using the force-state mapping technique; and (4) linearization of the identified nonlinear components, which are then incorporated into the linear damped model to create the linearized damped finite element model.

Crawley, E. F.↗
NASA NTRS1984

High time resolution measurements of rocket potential changes induced by electron beam emission

The transient charging and photon emission from the vacuum chamber testing of the Cooperative High Altitude Rocket Gun Experiment are studied. Graphs of the mother-daughter voltage versus time and high time resolution data related to the return current to the vehicle are examined. It is observed that for average sounding rocket densities of 10 to the -6th torr the slope of the voltage rise of the rocket begins to flatten 40 microsec after the onset of electron beam emission, and for higher gas pressure the rocket reaches a maximum voltage of 25 or 30 microsec after the onset of electron beam emission. The data reveal that the return current mechanism for the higher gas pressure is through the sheath.

Raitt, W. J.↗
NASA NTRS1990

Mobile Uninterruptible Power Supply

Proposed mobile unit provides 20 kVA of uninterruptible power. Used with mobile secondary power-distribution centers to provide power to test equipment with minimal cabling, hazards, and obstacles. Wheeled close to test equipment and system being tested so only short cable connections needed. Quickly moved and set up in new location. Uninterruptible power supply intended for tests which data lost or equipment damaged during even transient power failure.

Mears, Robert L.↗
NASA NTRS1991

Parched elastohydrodynamic lubrication: Instrumentation and procedure

A counter rotating bearing rig was designed and constructed to study transient elastohydrodynamic lubrication phenomena. New instrumentation is described and test procedures are documented. Ball and race speed measurement systems and the capacitance (film thickness) measurement system were upgraded. Methods for measuring bearing torque and race temperatures were implemented.

Schritz, Bryan↗
NASA NTRS1993

Characterization and snubbing of a bidirectional MCT in a resonant ac link converter

The MOS-Controlled Thyristor (MCT) is emerging as a powerful switch that combines the better characteristics of existing power devices. A study of switching stresses on an MCT switch under zero voltage resonant switching is presented. The MCT is used as a bidirectional switch in an ac/ac pulse density modulated inverter for induction motor drive. Current and voltage spikes are observed and analyzed with variations in the timing of the switching. Different snubber circuit configurations are under investigation to minimize the effect of these transients. The results will be extended to study and test the MCT switching in a medium power (5 hp) induction motor drive.

Lee, Tony↗
NASA NTRS1993

The GAMCIT gamma ray burst detector

The GAMCIT payload is a Get-Away-Special payload designed to search for high-energy gamma-ray bursts and any associated optical transients. This paper presents details on the design of the GAMCIT payload, in the areas of battery selection, power processing, electronics design, gamma-ray detection systems, and the optical imaging of the transients. The paper discusses the progress of the construction, testing, and specific design details of the payload. In addition, this paper discusses the unique challenges involved in bringing this payload to completion, as the project has been designed, constructed, and managed entirely by undergraduate students. Our experience will certainly be valuable to other student groups interested in taking on a challenging project such as a Get-Away-Special payload.

Mccall, Benjamin J.↗
NASA NTRS1995

Analysis of advanced solid rocket motor ignition phenomena

This report presents the results obtained from an experimental analysis of the flow field in the slots of the star grain section in the head-end of the advanced solid rocket motor during the ignition transient. This work represents an extension of the previous tests and analysis to include the effects of using a center port in conjunction with multiple canted igniter ports. The flow field measurements include oil smear data on the star slot walls, pressure and heat transfer coefficient measurements on the star slot walls and velocity measurements in the star slot.

Foster, Winfred A., Jr.↗
NASA NTRS2000

A Survey of Active Vibration Isolation Systems for Microgravity Applications

In view of the utility of space vehicles as orbiting science laboratories, the need for vibration isolation systems for acceleration sensitive experiments has gained increasing visibility. To date, three active microgravity vibration isolation systems have successfully been demonstrated in flight. This paper provides a tutorial discussion of the microgravity vibration isolation problem including a description of the acceleration environment of the International Space Station and attenuation requirements as well as a comparison of the dynamics of passive isolation, active rack-level isolation, and active payload-level isolation. This paper also surveys the flight test results of the three demonstrated systems: Suppression of Transient Accelerations By Levitation (STABLE); the Microgravity Vibration Isolation Mount (MIM); and the Active Rack Isolation System (ARIS).

Grodsinsky, Carlos M.↗