Communication: X-ray scattering from ionic liquids with pyrrolidinium cations
Abstract not provided
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Abstract not provided
Most silicon PV road maps forecast a continued reduction in wafer thickness, despite rapid declines in the primary incentive for doing so -- polysilicon feedstock price. Another common feature of most silicon-technology forecasts is the quest for ever-higher device performance at the lowest possible costs. The authors present data from device-performance and manufacturing- and system-installationcost models to quantitatively establish the incentives for manufacturers to pursue advanced (thin) wafer and (high efficiency) cell technologies, in an age of reduced feedstock prices. This analysis exhaustively considers the value proposition for high lifetime (p-type) silicon materials across the entire c-Si PV supply chain.
A spectrum of reproductive system anomalies (cryptorchidism, hypospadias, dysgenesis of Wolffian duct-derived tissues and prostate, and reduced sperm production) in male rats exposed in utero to phthalate esters (PEs) are thought to be caused by PE inhibition of fetal testosterone production. Recently, dibutyl and dipentyl phthalate (DBuP, DPnP) were shown to disrupt the retinol signaling pathway (RSP) in mouse pluripotent P19 embryonal carcinoma cells in vitro. The RSP regulates the synthesis and cellular levels of retinoic acid (RA), the active metabolite of retinol (vitamin A). In this new study, a total of 26 di- and mono-esters were screened to identify additional phthalate structures that disrupt the RSP and explore their mechanisms of action. The most potent PEs, those causing > 50% inhibition, contained aryl and cycloalkane groups or C4-C6 alkyl ester chains and were the same PEs reported to cause malformations in utero. They shared similar lipid solubility; logP values were between 4 and 6 and, except for PEs with butyl and phenyl groups, were stable for prolonged periods in culture. Mono- and cognate di-esters varied in ability to disrupt the RSP; e.g., DEHP was inactive but its monoester was active while DBuP was active yet its monoester was inactive. DBuP and dibenzyl phthalate both disrupted the synthesis of RA from retinol but not the ability of RA to activate gene transcription. Both PEs also disrupted the RSP in C3H10T1/2 multipotent mesenchymal stem cells. Based on this in vitro study showing that some PEs disrupt retinol signaling and previous in vivo studies that vitamin A/ RA deficiency and PEs both cause strikingly similar anomalies in the male rat reproductive system, we propose that PE-mediated inhibition of testosterone and RA synthesis in utero are both causes of malformations in male rat offspring.
An adaptive position control scheme for manipulators possessing either kinematic or actuator redundancy is presented. The controller is developed by considering the end-effector position control problem and redundancy resolution problem separately. The end-effector position control problem is solved by using an adaptive scheme to generate the Cartesian-space control input required to track the desired end-effector position trajectory; this control problem is nonredundant even for redundant robots. The Cartesian-space position controller is derived using a model reference adaptive control (MRAC) approach, and does not require knowledge of the complex robot dynamic model or parameter values for the robot or the payload. As a result, the scheme is applicable to both open-chain and closed-chain robots, and is computationally efficient for on-line implementations.
Uranium is one of the key contaminants of concern in groundwater as a result of past nuclear processing activities at the Department of Energy (DOE) facilities such as the Savannah River Site (SRS) in Aiken, South Carolina. SRS was one of the major nuclear processing facilities during the Cold War where plutonium was produced. Beginning with the implementation of the environmental cleanup program in 1981, SRS has become a hazardous waste management facility responsible for the storage and remediation of contaminated soil and groundwater from radionuclides. Approximately 1.8 billion gallons of acidic waste containing radionuclides and dissolved heavy metals was disposed in the F/H Area seepage basins. This led to the unintentional creation of highly contaminated groundwater plumes, consisting of radionuclides with an acidic pH between 3 and 5.5. The acidity of the plumes contributed to the mobility of several constituents of concern (COC) such as tritium ({sup 3}H), uranium-238 ({sup 238}U), iodine-129 ({sup 129}I), and strontium-90 ({sup 90}Sr) for the F-Area plume and {sup 3}H, {sup 90}Sr and mercury for the H-Area plume. This investigation will focus on uranium in the oxidation state +6 (U(VI)), which is a key contaminant of concern in the groundwater plume of the FArea. Initially, the pump-treat-reinject system was implemented from 1997 to 2003 to remove contaminants from polluted groundwater. Downgrade groundwater within the system would be pumped to the water treatment facility and re-injected upgrade within the aquifer. The effectiveness and sustainability of this process diminished over time. Therefore, it was discontinued and replaced with a funnel-and-gate process in 2004. This new process injects sodium hydroxide directly into the gates of the F-Area groundwater to effectively raise pH levels. By raising the pH of the groundwater, a treatment zone is created by reversing the acidic nature of the contaminated sediments and producing a negative net charge on the surface of sediment particles. As a result, the adsorption of cationic contaminants is expected to be enhanced. So far, this process has resulted in a decrease of {sup 90}Sr and {sup 238}U concentrations, though the concentration of iodine has been unaffected by this treatment. The solution used for the injections contains a high carbonate alkalinity in order to overcome the surface acidic conditions and natural partitions in the groundwater system. To maintain the neutral pH in the treatment zone, systematic injections are required. The continuous use of high concentrations of a carbonate solution to raise pH could re-mobilize uranium previously adsorbed within the treatment zone, though this has not been observed in the monitoring data. Humic substances (HS) are major components of soil organic matter. HS are polyfunctional organic macromolecules formed by the chemo-microbiological decomposition of biomass or dead organic matter. These substances are usually divided into three main fractions: humin (insoluble at all pH values), humic acid (soluble at pH greater than 3.5), and fulvic acid (soluble at all pH values). Humic acid carries a large number of functional groups such as aromatic rings, carboxyl groups, phenols, aliphatic chains, etc. Humic acid is an important ion exchange and metal complexing ligand with a high complexation capacity. The ability of humic acid to chemically bind to metals influences in their migration behavior and fate in natural systems. Various studies have suggested that the retention of U(VI) via sorption in the presence of humic acid is a complex process. For instance, humic acid can form an organic coating at the surface of minerals, which can enhance the sequestration of metals. Ivanov et al. (2012) studied the sorption of U(VI) sorption onto bentonite in the presence and absence of humic acid. The study found that uranium sorption in the presence of humic acid was enhanced at low pH (below 3.8) while at moderate pH (3.8 and 6.5) uranium sorption was reduced compared to the absence of humic acid. At high pH (7 and 9), uranium sorption was reduced for both the presence and absence of humic acid. Also, Krepelova et al. (2007) not only found that U(VI) sorption onto kaolinite was influenced by pH, U(VI) concentration, the presence of inorganic carbon species, and humic acid but also that U(VI) preferred to be adsorbed onto kaolinite as a uranyl-humate complex. This investigation analyzed the mechanisms of the synergetic interactions of humic acid and colloidal silica on the removal of uranium in the presence of pure minerals such as quartz, kaolinite and goethite which are characteristic of the F/H area. (authors)
The main focus of this work is to estimate Brassylic Acid (BA) using gas chromatography-mass spectrometry (GC-MS). BA is a product obtained from the oxidative cleavage of Erucic Acid (EA). BA has various applications for making nylons and high performance polymers. BA is a 13 carbon compound with two carboxylic acid functional groups at the terminal end. BA has a long hydrocarbon chain that makes the molecule less sensitive to some of the characterization techniques. Although BA can be characterized by NMR, both the starting material (EA) and products BA and nonanoic acid (NA) have peaks at similar {delta}, ppm values. Hence it becomes difficult for the quick estimation of BA during its synthesis.
Vehicle lightweighting reduces the amount of fuel consumed in a vehicle's use phase, but depending on what lightweight materials replace the conventional materials, and in what amounts, the manufacturing energy may increase or decrease. For carbon fiber reinforced polymer (CFRP), a next-generation lightweighting material, the increase in vehicle manufacturing energy is greater than the fuel savings, resulting in a net increase in energy consumption over a vehicle's manufacturing and use relative to a standard non-lightweighted car. [1] This work explores ways to reduce the supply chain energy of CFRP lightweighted vehicles through alternative production technologies and energy efficiency improvements. The objective is to determine if CFRP can offer energy savings comparable to or greater than aluminum, a conventional lightweighting material. Results of this analysis can be used to inform additional research and development efforts in CFRP production and future directions in lightweight vehicle production. The CFRP supply chain is modeled using the Material Flows through Industry (MFI) scenario modeling tool, which calculates 'mine to materials' energy consumption, material inventories and greenhouse gas emissions for industrial supply chains. In this analysis, the MFI tool is used to model the supply chains of two lightweighted vehicles, an aluminum intensive vehicle (AIV) and a carbon fiber intensive vehicle (CFV), under several manufacturing scenarios. Vehicle specifications are given in [1]. Scenarios investigated cover alternative carbon fiber (CF) feedstocks and energy efficiency improvements at various points in the vehicle supply chains. The alternative CF feedstocks are polyacrylonitrile, lignin and petroleum-derived mesophase pitch. Scenarios in which the energy efficiency of CF and CFRP production increases are explored using sector efficiency potential values, which quantify the reduction in energy consumption achievable when process equipment is upgraded to the most efficient available. Preliminary analyses indicate that producing CF from lignin instead of polyacrylonitrile, the most commonly used feedstock, reduces energy consumption in the CFRP supply chain by 7.5%, and that implementing energy efficient process equipment produces an additional 8% reduction. Final results will show if these potential reductions are sufficient to make the CFV energy savings comparable with AIV energy savings. [1] Das, S., Graziano, D., Upadhyayula, V. K., Masanet, E., Riddle, M., & Cresko, J. (2016). Vehicle lightweighting energy use impacts in US light-duty vehicle fleet. Sustainable Materials and Technologies, 8, 5-13.
Abstract not provided
Monolayers presenting methyl-terminated (hydrophobic) and hydroxyl-terminated (hydrophilic) surfaces on silica have been studied by molecular dynamics simulation and the effects of hydrogen bonding, chain length, and chain mixing on the frictional properties determined. The hydroxyl-terminated monolayers were found to show large adhesion zones as a result of strong interfacial interlayer hydrogen bonds; the interfacial sliding forces observed in the hydroxyl-terminated monolayers being one order of magnitude higher than the interfacial forces for the hydrophobic surfaces at the characteristic point of zero-load. Mixed hydroxyl- and methyl-terminated monolayers of equal length were found to exhibit intermediate shear stress values between those observed for pure monolayers, with the magnitude of the shear stress depending on the surface content of the hydroxyl-terminated chains. For mixed monolayers of unequal chain lengths, at high loads a maximum in the magnitude of the shear stress as a function of the length of the methyl-terminated chain was observed due to the creation of a buffer zone between the hydroxyl-terminated chains that produces strong hydrogen-bonding interactions. Here, the effect of a constant normal load or constant separation simulation ensemble on the results has also been studied and in general found to have minimal influence on the observed behavior, although some differences are observed for the shear stress at intermediate normal loads due to the formation of stronger hydrogen bond networks at constant load compared to constant separation.
Synthetic natural gas (SNG) is of great interest in reducing fossil energy consumption while maintaining compatibility with existing NG infrastructure and end-use applications equipment. SNG can be produced using clean H 2 generated from renewable or nuclear energy and CO 2 captured from stationary sources or the atmosphere. In this study, we develop an engineering process model of SNG production using Aspen Plus® and production scales reported by the industry. We examine the levelized cost and life cycle greenhouse gas (GHG) emissions of SNG production under various CO 2 supply scenarios. Considering the higher cost of H 2 transportation compared with CO 2 transportation, we assume that CO 2 feedstock is transported via pipeline to the H 2 production location, which is collocated with the SNG plant. We also evaluate the cost of CO 2 captured from the atmosphere, assuming the direct air capture process can occur near the SNG facility. Depending on the CO 2 supply chain, the levelized cost of SNG is estimated to be in the range of $\$45–76$ per million British thermal units (MMBtu) on a higher heating value (HHV) basis. The SNG production cost may be reduced to $\$27–57$/MMBtu-HHV by applying a tax credit available in the United States for low-carbon H 2 production (45V). With a lower electricity price of 3¢/kWh for water electrolysis and accounting for a 45V tax credit, the SNG cost reaches parity with the cost of fossil NG. Depending on the CO 2 supply chain, SNG can reduce life cycle GHG emissions by 52–88% compared with fossil NG.
This study tested whether the modest hypertrophy that develops in dogs in response to mitral regurgitation is due to a relatively small change in the rate of protein synthesis or, alternatively, is due to a decreased rate of protein degradation. After 3 mo of severe experimental mitral regurgitation, the left ventricular (LV) mass-to-body weight ratio increased by 23% compared with baseline values. This increase in LV mass occurred with a small, but not statistically significant, increase in the fractional rate of myosin heavy chain (MHC) synthesis (Ks), as measured using continuous infusion with [3H]leucine in dogs at 2 wk, 4 wk, and 3 mo after creation of severe mitral regurgitation. Translational efficiency was unaffected by mitral regurgitation as measured by the distribution of MHC mRNA in polysome gradients. Furthermore, there was no detectable increase in translational capacity as measured by either total RNA content or the rate of ribosome formation. These data indicate that translational mechanisms that accelerate the rate of cardiac protein synthesis are not responsive to the stimulus of mitral regurgitation. Most of the growth after mitral regurgitation was accounted for by a decrease in the fractional rate of protein degradation, calculated by subtracting fractional rates of protein accumulation at each time point from the corresponding Ks values. We conclude that 1) volume overload produced by severe mitral regurgitation does not trigger substantial increases in the rate of protein synthesis and 2) the modest increase in LV mass results primarily from a decrease in the rate of protein degradation.
ABSTRACT Arp 263 is a single irregularly shaped galaxy with intense star formation. Its short tidal features of low brightness visible in both optics and the H i line, as well as the strong non-circular motion of atomic gas in the outskirts, give pieces of evidence of a recent merging with some intruder, non-observed directly. We carried out spectral observations of this galaxy at the 6 m telescope of the Special Astrophysical Observatory. The spectra for three positions of the spectral slit were obtained: two of them cross the central region of the galaxy and the third one runs along the nearly straight narrow chain of clumps of emission gas with a length of 4–5 kpc. We derived the profiles of velocity, fluxes, and oxygen abundances (O/H) along the slits. We confirm that within the radius of several kpc the galaxy rotates regularly. The maximal value of the rotational velocity allows us to conclude that the dark mass of the galaxy prevails over the mass of its visible components. The observed velocity profile along the peripheral star-forming chain gives pieces of evidence that it is located outside of the plane of the disc, and the gas that formed the chain is probably falling back on to the disc after being ejected from the galaxy. We discuss that the observed chain of clumps is the result of gravitational instability of the gaseous filament.
Mobile electronic devices such as smart phones and tablets are a significant source of valuable metals that should be recycled. Each year over a billion devices are sold world-wide and the average life is only a couple years. Value metals in phones are gold, palladium, silver, copper, cobalt and nickel. Devices now contain increasing amounts of rare earth elements (REE). In recent years the supply chain for REE has moved almost exclusively to China. They are contained in displays, speakers and vibrators within the devices. By US Department of Energy (DOE) classification, specific REEs (Nd, Dy, Eu, Tb and Y) are considered critical while others (Ce, La and Pr) are deemed near critical. Effective recycling schemes should include the recovery of these critical materials. By including more value materials in a recovery scheme, more value can be obtained by product diversification and less waste metals remains to be disposed of. REEs are mined as a group such that when specific elements become critical significantly more ore must be processed to capture the dilute but valuable critical elements. Targeted recycling of items containing the more of the less available critical materials could address their future criticality. This presentation will describe work in developing aqueous electrochemistry-based schemes for recycling metals from scrap mobile electronics. The electrorecycling process generates oxidizing agents at an anode while reducing dissolved metals at the cathode. E vs pH diagrams and metals dissolution experiments are used to assess effectiveness of various solution chemistries. Although several schemes were envisioned, a two stages process has been the focus of work: 1) initial dissolution of Cu, Sn, Ag and magnet materials using Fe+3 generated in acidic sulfate and 2) final dissolution of Pd and Au using Cl2 generated in an HCl solution. Experiments were performed using simulated metal mixtures. Both Cu and Ag were recovered at ~ 97% using Fe+3 while leaving Au and Ag intact. REE were extracted from the dissolved mixture using conventional methods. A discussion of future research directions will be discussed.
Mobile electronic devices such as smart phones and tablets are a significant source of valuable metals that should be recycled. Each year over a billion devices are sold world-wide and the average life is only a couple years. Value metals in phones are gold, palladium, silver, copper, cobalt and nickel. Devices now contain increasing amounts of rare earth elements (REE). In recent years the supply chain for REE has moved almost exclusively to China. They are contained in displays, speakers and vibrators within the devices. By US Department of Energy (DOE) classification, specific REEs (Nd, Dy, Eu, Tb and Y) are considered critical while others (Ce, La and Pr) are deemed near critical. Effective recycling schemes should include the recovery of these critical materials. By including more value materials in a recovery scheme, more value can be obtained by product diversification and less waste metals remains to be disposed of. REEs are mined as a group such that when specific elements become critical significantly more ore must be processed to capture the dilute but valuable critical elements. Targeted recycling of items containing the more of the less available critical materials could address their future criticality. This presentation will describe work in developing aqueous electrochemistry-based schemes for recycling metals from scrap mobile electronics. The electrorecycling process generates oxidizing agents at an anode while reducing dissolved metals at the cathode. E vs pH diagrams and metals dissolution experiments are used to assess effectiveness of various solution chemistries. Although several schemes were envisioned, a two stages process has been the focus of work: 1) initial dissolution of Cu, Sn, Ag and magnet materials using Fe+3 generated in acidic sulfate and 2) final dissolution of Pd and Au using Cl2 generated in an HCl solution. Experiments were performed using simulated metal mixtures. Both Cu and Ag were recovered at ~ 97% using Fe+3 while leaving Au and Ag intact. REE were extracted from the dissolved mixture using conventional methods. A discussion of future research directions will be discussed.
We address the issue of flow effects on the phase behaviour of polymer nanocomposite melts by making use of a recently reported Hamiltonian set of evolution equations developed on principles of non-equilibrium thermodynamics. To this end, we calculate the spinodal curve, by computing values for the nanoparticle radius as a function of the polymer radius-of-gyration for which the second derivative of the generalized free energy of the system becomes zero. Under equilibrium conditions, we recover the phase diagram predicted by Mackay et al. [Science 311, 1740 (2006)]. Under non-equilibrium conditions, we account for the extra terms in the free energy due to changes in the conformations of polymer chains by the shear flow. Overall, our model predicts that flow enhances miscibility, since the corresponding miscibility window opens up for non-zero shear rate values.
Simultaneous elucidation of the glycan structure and the glycosylation site are needed to reveal the biological function of protein glycosylation. In this study, we employed a recent type of fragmentation termed higher energy collisional dissociation (HCD) to examine fragmentation patterns of intact glycopeptides generated from a mixture of standard glycosylated proteins. The normalized collisional energy (NCE) value for HCD was varied from 30% to 60% to evaluate the optimal conditions for the fragmentation of peptide backbones and glycoconjugates. Our results indicated that HCD with lower NCE valuespreferentially fragmented the sugar chains attached to the peptides to generate a ladder of neutral loss of monosaccharides, thus enabling the putative glycan structure characterization. Also, detection of the oxonium ions enabled unambiguous differentiation of glycopeptides from non-glycopeptides. On the contrary, HCD with higher NCE values preferentially fragmented the peptide backbone and thus provided information needed for confident peptide identification. We evaluated the HCD approach with alternating NCE parameters for confident characterization of intact N-linked and O-linked glycopeptides in a single liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis. In addition, we applied a novel data analysis pipeline, so-called GlycoFinder, to form a basis for automated data analysis. Overall, 38 unique intact glycopeptides corresponding to eight glycosylation sites (including six N-linked and two O-linked sites) were confidently identified from a standard protein mixture. This approach provided concurrent characterization of both, the peptide and the glycan, thus enabling comprehensive structural characterization of glycoproteins in a single LC-MS/MS analysis.
Fengyun-4A (FY-4A), which is the latest-generation Chinese geostationary meteorological satellite, measures solar reflection and thermal emission with high temporal, spatial, and spectral resolutions. It is expected to be highly beneficial for solar resource assessment and forecasting in China. This study is the first to estimate, using FY-4A and a random forest model, the global horizontal irradiance (GHI) at a 4-km–15-min spatio-temporal resolution over China, as a means to arrive at a solar photovoltaic (PV) resource map. In terms of GHI estimates, the root mean square error and mean bias error between hourly measured and retrieved values are 147.02 (35.2%), –5.64 W/m 2 (–1.4%), respectively, whereas the values of daily estimates are 29.20 (18.0%), –2.97 W/m 2 (–1.3%). The retrieval accuracy is found much better for instances with solar zenith angles smaller than 60°. Relatively larger errors are found at locations in the Sichuan Basin and northeastern China, which can be attributed to bright surfaces and/or strong cloud transients. With the retrieved irradiance, PV resource is derived through a physical model chain. The annual mean PV resource map suggests that, over most of the west areas, the annual mean effective irradiance exceeds 1700 kWh/m 2 , with the highest value found in Tibet (around 2000 kWh/m 2 per annum). Eastern China has an annual effective irradiance of only 1300–1500 kWh/m 2 . In conclusion, the region with poorest solar resource is the Sichuan Basin (less than 1100 kWh/m 2 per annum).
Enzymatic Fisher-Tropsch (FT) process catalyzed by vanadium (V)-nitrogenase can convert carbon monoxide (CO) to longer-chain hydrocarbons (>C2) under ambient conditions, although this process requires high-cost reducing agent(s) and/or the ATP-dependent reductase as electron and energy sources. Using visible light-activated CdS@ZnS (CZS) core-shell quantum dots (QDs) as alternative reducing equivalent for the catalytic component (VFe protein) of V-nitrogenase, we first report a CZS : VFe biohybrid system that enables effective photo-enzymatic C−C coupling reactions, hydrogenating CO into hydrocarbon fuels (up to C4) that can be hardly achieved with conventional inorganic photocatalysts. Surface ligand engineering optimizes molecular and opto-electronic coupling between QDs and the VFe protein, realizing high efficiency (internal quantum yield >56 %), ATP-independent, photon-to-fuel production, achieving an electron turnover number of >900, that is 72 % compared to the natural ATP-coupled transformation of CO into hydrocarbons by V-nitrogenase. The selectivity of products can be controlled by irradiation conditions, with higher photon flux favoring (longer-chain) hydrocarbon generation. The CZS : VFe biohybrids not only can find applications in industrial CO removal for high-value-added chemical production by using the cheap, renewable solar energy, but also will inspire related research interests in understanding the molecular and electronic processes in photo-biocatalytic systems.