Search NASA⌕ Search

SEARCH · Search NASA

Results for “WALLS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

A wall interference assessment/correction interface measurement system for the NASA/ARC 12-ft PWT

Development of complex air vehicle configurations is placing increasing demands on wind tunnel testing capabilities. A major area of concern is wall induced interference. Recent developments in wall interference technology provide a means for assessing and correcting for the wall induced interference using information contained in the distribution of flow variables measured at, or near, the wall. The restoration of the NASA-ARC 12-ft pressure wind tunnel (PWT) provides an opportunity to incorporate a measurement system with which wall interference assessment/correction (WIAC) technology can be applied. In this first phase of the development of a WIAC system for the PWT, the design criteria for the placement and the geometry of wall static pressure orifices were determined with a three step approach. First, the operational environment of the PWT was analyzed as to the requirements for the WIAC system. Second, appropriate wall interference theories were evaluated against the requirements determined from the operational environment. Third, the flow about representative models in the PWT was calculated and, specifically, the pressure signatures at the location of the test section wall were obtained. The number of discrete pressure measurements and their locations were determined by curve fitting the pressure distribution through the discrete measurements and evaluating the resulting error.

Source record↗

Comparison of conventional and adaptive wall wind tunnel results with regard to Reynolds number effects

A comparison of results from conventional and adaptive wall wind tunnels with regard to Reynolds number effects was carried out. The special objective of this comparison was to confirm or reject earlier conclusions, soley based on conventional wind tunnel results, concerning the influence of viscous effects on the characteristics of partially open wind tunnel walls, hence wall interference. The following postulations could be confirmed: (1) certain classes of supercritical airfoils exhibit a non-linear increase in lift which is, at least in part, related to viscous-inviscid interactions on the airfoil. This non-linear lift characteristic can erroneously be suppressed by sidewall interference effects in addition to being affected by changes in Reynolds number. Adaptive walls seem to relieve the influence of sidewall interference; (2) the degree of (horizontal) wall interference effects can be significantly affected by changes in Reynolds number, thus appearing as true Reynolds number effects; (3) perforated wall characteristics seem much more susceptible to viscous changes than the characteristics of slotted walls; here, blockage interference may be most severely influenced by viscous changes; and (4) real Reynolds number effects are present on the CAST 10-2/DOA 2 airfoil; they were shown to be appreciable also by the adaptive wall wind tunnel tests.

Stanewsky, E.↗

Residual interference and wind tunnel wall adaption

Measured flow variables near the test section boundaries, used to guide adjustments of the walls in adaptive wind tunnels, can also be used to quantify the residual interference. Because of a finite number of wall control devices (jacks, plenum compartments), the finite test section length, and the approximation character of adaptation algorithms, the unconfined flow conditions are not expected to be precisely attained even in the fully adapted stage. The procedures for the evaluation of residual wall interference are essentially the same as those used for assessing the correction in conventional, non-adaptive wind tunnels. Depending upon the number of flow variables utilized, one can speak of one- or two-variable methods; in two dimensions also of Schwarz- or Cauchy-type methods. The one-variable methods use the measured static pressure and normal velocity at the test section boundary, but do not require any model representation. This is clearly of an advantage for adaptive wall test section, which are often relatively small with respect to the test model, and for the variety of complex flows commonly encountered in wind tunnel testing. For test sections with flexible walls the normal component of velocity is given by the shape of the wall, adjusted for the displacement effect of its boundary layer. For ventilated test section walls it has to be measured by the Calspan pipes, laser Doppler velocimetry, or other appropriate techniques. The interface discontinuity method, also described, is a genuine residual interference assessment technique. It is specific to adaptive wall wind tunnels, where the computation results for the fictitious flow in the exterior of the test section are provided.

Mokry, Miroslav↗

Microwave background distortions from domain walls

Domain walls arising in a cosmic phase transition after decoupling were recently proposed as seeds for the formation of large scale structure. The distortion induced in the microwave background radiation is calculated in dependence of the wall thickness, surface density, scalar field potential, cosmic redshift and the velocity of the wall. It was found that the maximal redshift distortion for both spherical and planar walls is of the order pi G sigma H(sup -1)(sub 0), where sigma is the surface energy density and H(sup -1)(sub 0) the Hubble parameter. It was also found that, for a wall thickness smaller than the horizon, walls can be treated as infinitely thin, i.e., the redshift distortion is independent of the wall thickness and the specific form of the scalar potential. For planar walls moving with a Lorentz-factor gamma the redshift distortion is enhanced by gamma cubed.

Goetz, Guenter↗

Dynamical evolution of domain walls in an expanding universe

Whenever the potential of a scalar field has two or more separated, degenerate minima, domain walls form as the universe cools. The evolution of the resulting network of domain walls is calculated for the case of two potential minima in two and three dimensions, including wall annihilation, crossing, and reconnection effects. The nature of the evolution is found to be largely independent of the rate at which the universe expands. Wall annihilation and reconnection occur almost as fast as causality allows, so that the horizon volume is 'swept clean' and contains, at any time, only about one, fairly smooth, wall. Quantitative statistics are given. The total area of wall per volume decreases as the first power of time. The relative slowness of the decrease and the smoothness of the wall on the horizon scale make it impossible for walls to both generate large-scale structure and be consistent with quadrupole microwave background anisotropy limits.

Press, William H.↗

A numerical study of shock wave/boundary layer interaction in nonequilibrium chemically reacting air - The effects of catalytic walls

This paper presents a numerical study that investigate the effects of nonequilibrium chemistry, and in particular, wall catalycity on the separated flow region generated by an oblique shock wave impinging upon a flat plate boundary layer. To obtain a solution to this problem, the full two dimensional Navier-Stokes equations were solved using MacCormack's predictor-corrector time dependent technique on a rectangular grid. Nonequilibrium chemistry was included by utilizing the 5 species, 17 reaction modified Dunn-Kang chemical kinetics model. Separate results were obtained for: calorically perfect, chemically reacting - noncatalytic wall, and chemically reacting - fully catalytic wall cases, for a given set of flow conditions. A direct comparison of all three cases revealed a slight decrease in the peak heat transfer for the noncatalytic wall case, as compared to the calorically perfect case. On the other hand, the fully catalytic wall case had a tremendous increase in the peak surface heat transfer. It is concluded that, for the particular conditons treated here (nearly frozen flow in the free stream), the effects of the nonequilibrium chemically reacting flow on the shock-wave/boundary-layer interaction depend critically on the catalycity of the wall, having virtually no effect for the case of a noncatalytic wall, and exerting a tremendous effect for a fully catalytic wall.

Grumet, Adam A.↗

Kolmogorov Behavior of Near-Wall Turbulence and Its Application in Turbulence Modeling

The near-wall behavior of turbulence is re-examined in a way different from that proposed by Hanjalic and Launder and followers. It is shown that at a certain distance from the wall, all energetic large eddies will reduce to Kolmogorov eddies (the smallest eddies in turbulence). All the important wall parameters, such as friction velocity, viscous length scale, and mean strain rate at the wall, are characterized by Kolmogorov microscales. According to this Kolmogorov behavior of near-wall turbulence, the turbulence quantities, such as turbulent kinetic energy, dissipation rate, etc. at the location where the large eddies become Kolmogorov eddies, can be estimated by using both direct numerical simulation (DNS) data and asymptotic analysis of near-wall turbulence. This information will provide useful boundary conditions for the turbulent transport equations. As an example, the concept is incorporated in the standard k-epsilon model which is then applied to channel and boundary flows. Using appropriate boundary conditions (based on Kolmogorov behavior of near-wall turbulence), there is no need for any wall-modification to the k-epsilon equations (including model constants). Results compare very well with the DNS and experimental data.

Shih, Tsan-Hsing↗

Drag reduction at a plane wall

The objective is to determine by analytical means how drag on a plane wall may be modified favorably using a minimal amount of flow information - preferably only information at the wall. What quantities should be measured? How should that information be assimilated in order to arrive at effective control? As a prototypical problem, incompressible, viscous flow, governed by the Navier-Stokes equations, past a plane wall at which the no-slip condition was modified was considered. The streamwise and spanwise velocity components are required to be zero, but the normal component is to be specified according to some control law. The challenge is to choose the wall-normal velocity component based on flow conditions at the wall so that the mean drag is as small as possible. There can be no net mass flux through the wall, and the total available control energy is constrained. A turbulent flow is highly unsteady and has detailed spatial structure. The mean drag on the wall is the integral over the wall of the local shear forces exerted by the fluid, which is then averaged in time; it is a 'macroscopic' property of the flow. It is not obvious how unsteady boundary control is to be applied in order to modify the mean flow most effectively, especially in view of the non- self-adjoint nature of the governing equations. An approximate analytical solution to the suboptimal scheme is pursued.

Hill, D. C.↗

Adaptive wall technology for minimization of wind tunnel boundary interferences - where are we now?

The status of adaptive wall technology to improve wind tunnel simulations for 2- and 3-D testing is reviewed. This technology relies on the test section flow boundaries being adjustable, using a tunnel/computer system to control the boundary shapes without knowledge of the model under test. This paper briefly overviews the benefits and shortcomings of adaptive wall testing techniques. A historical perspective highlights the disjointed development of these testing techniques from 1938 to present. Currently operational transonic Adaptive Wall Test Sections (AWTSs) are detailed, showing a preference for the simplest AWTS design with two solid flexible walls. Research highlights show that quick wall adjustment procedures are available and AWTSs, with impervious or ventilated walls, can be used through the transonic range up to M(sub infinity) = 1.2. The requirements for production testing in AWTSs are discussed, and conclusions drawn as to the current status of adaptive wall technology. In 2-D testing, adaptive wall technology is mature enough for general use, even in cryogenic wind tunnels. In 3-D testing, this technology has not been pursued aggressively, because of the inertia against change in testing techniques, and preconceptions about the difficulties of using AWTSs.

Wolf, Stephen W. D.↗

The Effects of LOX Post Biasing on SSME Injector Wall Compatibility

An experimental investigation has been carried out to examine the effects of LOX post biasing of a shear coaxial injector on the behavior of the spray near a chamber wall. The experimental work was performed with inert propellant simulants in a high-pressure chamber. Injector flow rates and chamber pressure were designed to match the Space Shuttle Main Engine (SSME) injector gas-to-liquid density and velocity ratio at the point of propellant injection. Measurements of liquid mass flux, gas phase velocity and droplet size were made using mechanical patternation and phase Doppler interferometry techniques. The measurements revealed that the liquid mass flux distribution shifts away from the wall with increasing LOX post bias away from the wall. The shift in the liquid flux distribution was much greater than that caused by the angling of the LOX post alone. Gas velocity near the wall simultaneously increased with increasing LOX post bias away from the wall. The increase in wall side gas velocity was due to the higher fraction of gas injected on the wall side of the injector as a result of the eccentricity at the injector exit. The net result is a decrease in mixture ratio near the wall. Estimates of heat transfer and engine performance relative to the unbiased case are presented.

Strakey, P. A.↗

Bubble Formation on a Wall in Cross-Flowing Liquid and Surrounding Fluid Motion,With and Without Heating

Application of gas-liquid two-phase flow systems for space-based thermal management and for the HEDS program demands a precise control of bubble size distribution in liquid. The necessity of bulk liquid motion for controlling bubble size and frequency in the space environment has been suggested by recent studies on pool, forced convection boiling and bubble formation in flowing liquid. The present work, consisting of two parts, explores bubble generation at wall in a cross-flowing liquid, i.e., in a forced convection boiling configuration. A schematic is shown. The first part looks into the bubble formation process under isothermal conditions in a reduced gravity environment, by injecting gas through a hole in the wall of a flowing liquid channel. In the latter part with channel wall heating, flow and temperature fields near a single bubble are studied under normal (1-g) and micro-gravity (mu-g) conditions. The objective of the isothermal experiments is to experimentally investigate the effects of liquid cross-flow velocity, gas flow rate, and orifice diameter on bubble formation. Data were taken mainly under reduced gravity conditions but some data were taken in normal gravity for comparison. The reduced gravity experiment was conducted aboard the NASA DC-9 Reduced Gravity Aircraft. The results show that the process of bubble formation and detachment depends on gravity, the orifice diameter (D(sub N)), the gas flow rate (Q(sub g)), and the liquid cross-flow velocity (U(sub L)). The reduced gravity data are shown. The data are analyzed based on a force balance, and two different detachment mechanisms are identified. When the gas momentum is large, the bubble detaches from the injection orifice as the gas momentum overcomes the attaching effects of liquid drag and inertia. The surface tension force is much reduced because a large part of the bubble pinning edge at the orifice is lost as the bubble axis is tilted by the liquid flow. When the gas momentum is small, the force balance in the liquid flow direction is important, and the bubble detaches when the bubble axis inclination exceeds a certain angle. With wall heating, liquid motion around an air bubble in cross-flowing 2cs silicone oil is experimentally investigated in 1-g. A spectral element based steady 2D numerical model is also developed. The traces of particles from experimental flow visualization and the corresponding computed streamlines are shown. At the upstream side of the bubble facing the cross-flow, thermocapillary and forced convection create liquid motion away from the wall, up along the surface. At the downstream side, a competing interaction between the two creates a recirculation cell, causing the bulk liquid to stagnate on the surface and separate thereafter. The important dimensionless parameters are - Surface tension and local cross-flow Reynolds numbers R(sub sigma)(U(sub ref)a/v) and Re(sub loc)(U(sub L)a/v), respectively based on reference thermocapillary U(sub ref)(sigma(sub T)Delta.T/mu, Delta T=T(sub wall)-T(sub liquid)) and local cross-flow velocity U(sub L), Prandtl number P(sub r) and Grashoff number Gr(rho.g.beta.DeltaTa(sup 3)/mu.v). Variation of the stagnation point with R(sub sigma) and Re(sub loc) is shown. Also shown are good agreement between experimental and numerical results in 1-g. The computational model is extended to mu-g condition to investigate temperature and velocity on the bubble surface, stagnation and reattachment points of the recirculation cell and wall heat transfer. It is observed that wall heating significantly alters the flow field around the bubble and thus the forces acting on the bubble, which control its detachment. Thus a combination of heating and liquid cross-flow can be utilized to precisely control bubble formation in a mu-g environment.

Bhunia, Avijit↗

A Modified Wall Matching Treatment to Account for Local Solid to Fluid Thermal Coupling

The wall-matching methodology of Wilcox is modified to include a solid-wall, thermal-conduction model. This coupled fluid-thermal-structure model is derived assuming that the wall thermal-structure behavior is locally one-dimensional and that structural deformations, due to thermally induced stresses, are not significant. The one-dimensional coupled fluid-thermal-structure model is derived such that the wall temperature is removed as an independent boundary condition variable. The one-dimensional coupled fluid-thermal-structure model is also derived for the general case of an arbitrary mixture of thermally prefect gases and a wall of arbitrary thickness and conductivity by using a compressible, streamwise-pressure-gradient-corrected, wall-matching function and Fourier's law of heat conduction. The resulting model was implemented in the VULCAN CFD code as a new boundary condition type. VULCAN was then used to simulate a two-dimensional Mach 6 wind tunnel facility nozzle flow to demonstrate/validate the one-dimensional coupled fluid-thermal-structure model. The nozzle internal-wall surface temperature and heat transfer distributions computed using the one-dimensional coupled fluid-thermal-structure model are compared to wall temperature and heat transfer distributions from an iterative multi-dimensional analysis obtained by coupling the VULCAN CFD code and the MSC/NASTRAN-thermal code. The one-dimensional coupled fluid-thermal-structure model analysis is shown to be very robust and in excellent agreement with the multi-dimensional iteratively coupled analysis. It is also shown that the one-dimensional analysis can be used as an initial guess for the multi-dimensional iteratively coupled analysis.

White, Jeffery A.↗

Characterization of the Test Section Walls at the 14- by 22-Foot Subsonic Tunnel

The test section walls of the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel are known to move under thermal and pressure loads. Videogrammetry was used to measure wall motion during the summer of 2002. In addition, a laser distancemeter was used to measure the relative distance between the test section walls at a single point. Distancemeter and videogrammetry results were consistent. Data were analyzed as a function of temperature and pressure to determine their effects on wall motion. Data were collected between 50 and 100 F, 0 and 0.315 Mach, and dynamic pressures of 0 and 120 psf. The overall motion of each wall was found to be less than 0.25 in. and less than facility personnel anticipated. The results show how motion depends on the temperature and pressure inside the test section as well is the position of the boundary layer vane. The repeatability of the measurements was +/-0.06 in. This report describes the methods used to record the motion of the test section walls and the results of the data analysis. Future facility plans include the development of a suitable wall restraint system and the determination of the effects of the wall motion on tunnel calibration.

Lunsford, Charles B.↗

A Modified Wall Matching Treatment to Account for Local Solid to Fluid Thermal Coupling

The wall-matching methodology of Wilcox is modified to include a solid-wall, thermal-conduction model. This coupled fluid-thermal-structure model is derived assuming that the wall thermal-structure behavior is locally one-dimensional and that structural deformations, due to thermally induced stresses, are not significant. The one-dimensional coupled fluid-thermal-structure model is derived such that the wall temperature is removed as an independent boundary condition variable. The one-dimensional coupled fluid-thermal-structure model is also derived for the general case of an arbitrary mixture of thermally prefect gases and a wall of arbitrary thickness and conductivity by using a compressible, streamwise-pressure-gradient-corrected, wall-matching function and Fourier's law of heat conduction. The resulting model was implemented in the VULCAN CFD code as a new boundary condition type. VULCAN was then used to simulate a two-dimensional Mach 6 wind tunnel facility nozzle flow to demonstrate/validate the one-dimensional coupled fluid-thermal-structure model. The nozzle internal-wall surface temperature and heat transfer distributions computed using the one-dimensional coupled fluid-thermal-structure model are compared to wall temperature and heat transfer distributions from an iterative multi-dimensional analysis obtained by coupling the VULCAN CFD code and the MSC/NASTRAN-thermal code. The one-dimensional coupled fluid-thermal-structure model analysis is shown to be very robust and in excellent agreement with the multi-dimensional iteratively coupled analysis. It is also shown that the one-dimensional analysis can be used as an initial guess for the multi-dimensional iteratively coupled analysis.

White, Jeffery A.↗

Ballistic Limit Equation for Single Wall Titanium

Hypervelocity impact tests and hydrocode simulations were used to determine the ballistic limit equation (BLE) for perforation of a titanium wall, as a function of wall thickness. Two titanium alloys were considered, and separate BLEs were derived for each. Tested wall thicknesses ranged from 0.5mm to 2.0mm. The single-wall damage equation of Cour-Palais [ref. 1] was used to analyze the Ti wall's shielding effectiveness. It was concluded that the Cour-Palais single-wall equation produced a non-conservative prediction of the ballistic limit for the Ti shield. The inaccurate prediction was not a particularly surprising result; the Cour-Palais single-wall BLE contains shield material properties as parameters, but it was formulated only from tests of different aluminum alloys. Single-wall Ti shield tests were run (thicknesses of 2.0 mm, 1.5 mm, 1.0 mm, and 0.5 mm) on Ti 15-3-3-3 material custom cut from rod stock. Hypervelocity impact (HVI) tests were used to establish the failure threshold empirically, using the additional constraint that the damage scales with impact energy, as was indicated by hydrocode simulations. The criterion for shield failure was defined as no detached spall from the shield back surface during HVI. Based on the test results, which confirmed an approximately energy-dependent shield effectiveness, the Cour-Palais equation was modified.

Ratliff, J. M.↗

Channel Wall Nozzle Manufacturing Technology Advancements for Liquid Rocket Engines

A regeneratively-cooled nozzle is a critical component for expansion of the hot gases to enable high temperature and performance liquid rocket engines systems. Channel wall nozzles are a design solution used across the propulsion industry as a simplified method to fabricate the nozzle structure with internal coolant passages. The scale and complexity of the channel wall nozzle (CWN) design is challenging to fabricate leading to extended lead times and higher costs. Some of these challenges include: 1) unique and high temperature materials, 2) Tight tolerances during manufacturing and assembly to contain high pressure propellants, 3) thin-walled features to maintain adequate wall temperatures, and 4) Unique manufacturing process operations and tooling. The United States (U.S.) National Aeronautics and Space Administration (NASA) along with U.S. specialty manufacturing vendors are maturing modern fabrication techniques to reduce complexity and decrease costs associated with channel wall nozzle manufacturing technology. Additive Manufacturing (AM) is one of the key technology advancements being evaluated for channel wall nozzles. Much of additive manufacturing for propulsion components has focused on powder bed fusion, but the scale is not yet feasible for application to large scale nozzles. NASA is evolving directed energy deposition (DED) techniques for nozzles including arc-based deposition, blown powder deposition, and Laser Wire Direct Closeout (LWDC). There are different approaches being considered for fabrication of the nozzle and each of these DED processes offer unique process steps for rapid fabrication. The arc-based and blown powder deposition techniques are being used for the forming of the CWN liner. A variety of materials are being demonstrated including Inconel 625, Haynes 230, JBK-75, and NASA HR-1. The blown powder DED process is also being demonstrated for forming an integral channel nozzle in a single operation in similar materials. The LWDC process is a method for closing out the channels within the liner and forming the structural jacket using a localized laser wire deposition technique. Identical materials mentioned above have been used for this process in addition to bimetallic closeout (C-18150–SS347, and C-18150–Inconel 625). NASA has completed process development, material characterization, and hot-fire testing on a variety of these channel wall nozzle fabrication techniques. This paper will present an overview of the various processes and materials being evaluated and the results from the hot-fire testing. Future development and technology focus areas will also be discussed relative to channel wall nozzle manufacturing.

Gradl, Paul R.↗

Size, Shape, and Arrangement of Cellulose Microfibril in Higher Plant Cell Walls

Plant cell walls from maize (Zea mays L.) are imaged using atomic force microscopy (AFM) at the sub-nanometer resolution. We found that the size and shape of fundamental cellulose elementary fibril (CEF) is essentially identical in different cell wall types, i.e., primary wall (PW), parenchyma secondary wall (pSW), and sclerenchyma secondary wall (sSW), which is consistent with previously proposed 36-chain model (Ding et al., 2006, J. Agric. Food Chem.). The arrangement of individual CEFs in these wall types exhibits two orientations. In PW, CEFs are horizontally associated through their hydrophilic faces, and the planar faces are exposed, forming ribbon-like macrofibrils. In pSW and sSW, CEFs are vertically oriented, forming layers, in which hemicelluloses are interacted with the hydrophobic faces of the CEF and serve as spacers between CEFs. Lignification occurs between CEF-hemicelluloses layers in secondary walls. Furthermore, we demonstrated quantitative analysis of plant cell wall accessibility to and digestibility by different cellulase systems at real-time using chemical imaging (e.g., stimulated Raman scattering) and fluorescence microscopy of labeled cellulases (Ding et al., 2012, Science, in press).

59 BASIC BIOLOGICAL SCIENCES↗

Airfoil with varying wall thickness

An airfoil includes an airfoil body that has a peripheral wall that defines an exterior side and an interior side that bounds an internal cavity in the airfoil body. The peripheral wall has first and second wall sections joined by a transition section. The first wall section is thicker than the second wall section. The transition section provides a change in thickness between the first wall section and the second wall section. The second wall section includes a cooling hole that has a first end that opens to the internal cavity at the interior side and a second end that opens to the exterior side.

42 ENGINEERING↗