Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Effect of negative bias voltage on CrN films deposited by arc ion plating. II. Film composition, structure, and properties

Chromium nitride (CrN) films were deposited on Si wafers by arc ion plating at various negative bias voltages and several groups of N{sub 2}/Ar gas flux ratios and chamber gas pressures. The authors systematically investigated the influence of negative bias voltage on the synthesis, composition, microstructure, and properties of the arc ion plating (AIP) CrN films. In this article, the authors investigated the influence of negative bias voltage on the chemical composition, structure, and mechanical properties of the CrN films. The results showed that the chemical composition and phase structure of the AIP CrN films were greatly altered by application of negative bias voltage. Due to the selective resputtering effect, substoichiometric CrN films were obtained. With increase in bias voltages, the main phases in the films transformed from Cr+CrN to Cr{sub 2}N at low N{sub 2}/Ar flow ratios, whereas the films at high N{sub 2}/Ar flow ratios retained the CrN phase structure. The CrN films experienced texture transformation from CrN (200) to CrN (220), and Cr{sub 2}N (300) to Cr{sub 2}N(300)+Cr{sub 2}N(110). Increase in negative bias voltage also resulted in microstructure evolution of coarse columnar grains{yields}fine columnar grains{yields}quasiamorphous microstructure{yields}recrystallized structures. From the experimental results, the authors proposed a new structure zone model based on enhanced bombardment of incident ions by application of negative bias voltage. The influence of negative bias voltage on the microhardness and residual stresses of the films and the inherent mechanisms were also explored.

36 MATERIALS SCIENCE↗

Probabilistic simulation of multi-scale composite behavior

A methodology is developed to computationally assess the probabilistic composite material properties at all composite scale levels due to the uncertainties in the constituent (fiber and matrix) properties and in the fabrication process variables. The methodology is computationally efficient for simulating the probability distributions of material properties. The sensitivity of the probabilistic composite material property to each random variable is determined. This information can be used to reduce undesirable uncertainties in material properties at the macro scale of the composite by reducing the uncertainties in the most influential random variables at the micro scale. This methodology was implemented into the computer code PICAN (Probabilistic Integrated Composite ANalyzer). The accuracy and efficiency of this methodology are demonstrated by simulating the uncertainties in the material properties of a typical laminate and comparing the results with the Monte Carlo simulation method. The experimental data of composite material properties at all scales fall within the scatters predicted by PICAN.

Liaw, D. G.↗

Evolution of elastic and thermal properties of cementitious composites containing micro-size lightweight fillers after exposure to elevated temperature

This work studies the evolution of elastic and thermal properties of cementitious composites containing micro-size lightweight fillers after exposure to elevated temperatures (up to 800 °C). A multiscale investigation is carried out to study the thermal degradation of cementitious composite materials at multiple scale levels: at cement past level, the dehydration kinetics of cement hydrates (i.e., C–S–H, CH and aluminate hydrates) and development of microcracks are studied as functions of exposure temperatures. The damage mechanism of the inclusion phases and damages within the interfacial transition zone (ITZ) under elevated temperature are also investigated. In addition, the change of mechanical (i.e., elastic moduli, compressive strengths) and thermal (thermal conductivities) properties are measured as functions of the exposure temperature. Based on the experimental studies, a multiscale thermal degradation model is developed where the thermal degradations of cement paste (including water composition, porosity, and solid phase changes), inclusion phases, and the interfaces are captured through a multiscale sub-stepping homogenization scheme. The thermal degradation model is validated through multiple sets of experimental data. Finally, the influence of key parameters including the particle size distribution of the inclusions, the chemical composition, as well as the effects of ITZ damage are studied.

36 MATERIALS SCIENCE↗

Correlation of rocket propulsion fuel properties with chemical composition using comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry followed by partial least squares regression analysis

There is an increased need to more fully assess and control the composition of kerosene based rocket propulsion fuels, namely RP-1 and RP-2. In particular, it is crucial to be able to make better quantitative connections between the following three attributes: (a) fuel performance, (b) fuel properties (flash point, density, kinematic viscosity, net heat of combustion, hydrogen content, etc) and (c) the chemical composition of a given fuel (i.e., specific chemical compounds and compound classes present as a result of feedstock blending and processing). Indeed, recent efforts in predicting fuel performance through modeling put greater emphasis on detailed and accurate fuel properties and fuel compositional information. In this regard, advanced distillation curve (ADC) metrology provides improved data relative to classical boiling point and volatility curve techniques. Using ADC metrology, data obtained from RP-1 and RP-2 fuels provides compositional variation information that is directly relevant to predictive modeling of fuel performance. Often, in such studies, one-dimensional gas chromatography (GC) combined with mass spectrometry (MS) is typically employed to provide chemical composition information. Building on approaches using GC-MS, but to glean substantially more chemical composition information from these complex fuels, we have recently studied the use of comprehensive two dimensional gas chromatography combined with time-of-flight mass spectrometry (GC × GC - TOFMS) to provide chemical composition data that is significantly richer than that provided by GC-MS methods. In this report, by applying multivariate data analysis techniques, referred to as chemometrics, we are able to readily model (correlate) the chemical compositional information from RP-1 and RP-2 fuels provided using GC × GC - TOFMS, to the fuel property information such as that provided by the ADC method and other specification properties. We anticipate that this new chemical analysis strategy will have broad implications for the development of high fidelity composition-property models, leading to an optimized approach to fuel formulation and specification for advanced engine cycles.

fuel↗

Improved Plate and Beam Models for Thermoviscoelastic Constitutive Modeling of Composites

The effective properties of composites are influenced by the time-dependent behavior of polymer matrices very sensitive to changes in temperature. Improved plate and beam models are required to efficiently design, and simulate composite structures when the long-term performance of large anisotropic composite structures is the matter of interest. In this work, mechanics of structure genome (MSG) is used to con-struct linear thermoviscoelastic plate and beam models that can homogenize three-dimensional heterogeneous materials made of constituents with time- and temperature-dependent behavior. The formulation derives the transient strain energy based on integral formulation for thermorheologically simple materials subject to finite temperature changes with the restriction that the strain is small. The reduced time parameter is introduced to relate the time-temperature dependency of the anisotropic material by means of master curves at reference conditions. The new formulation has been implemented in SwiftCompTM, a general-purpose multiscale constitutive modeling code based on MSG. Experimental data and three-dimensional direct numerical simulations of thin-ply high-strain composites (TP-HSC) using a commercial finite element analysis (FEA) package are conducted to verify the accuracy of SwiftCompTM results. The paper also analyzes the relationship between the shift factor of the polymer matrix and the temperature dependencies of the effective beam properties.

Finite element analysis↗

Effect of B{sub 2}O{sub 3}-Bi{sub 2}O{sub 3}-SiO{sub 2}-ZnO glass on the dielectric and magnetic properties of ferroelectric/ferromagnetic composite for low temperature cofired ceramic technology

Ni-Cu-Zn ferrite/BaTiO{sub 3} composites with different additive amounts of B{sub 2}O{sub 3}-Bi{sub 2}O{sub 3}-SiO{sub 2}-ZnO (BBSZ) glass have been prepared by a conventional solid-reaction method and sintered at 900 deg. C to adapt to low temperature cofired ceramic (LTCC) technology. The dielectric and magnetic properties of the composites can be effectively improved with increasing BBSZ content. Here, the BBSZ glass mainly plays two roles, one is as a sintering aid promoting grain growth and the other is as a low permittivity phase or nonmagnetic phase leading to dilution effect on the dielectric or magnetic properties of the composites. The effect degree of above two roles is related to the variation in BBSZ content and has been discussed combining with the effective medium theory. The lower and upper bounds for the effective permittivity and permeability have been given by the Maxwell-Garnett rules.

36 MATERIALS SCIENCE↗

Composition, morphology, and properties of sodium-bismuth tungstate crystals

A correlation has been revealed between the formation conditions, composition, morphology, and physicochemical properties of NaBi{sub 1-x}(W{sub 1+y}O{sub 4}){sub 2} crystals (0 {<=} x {<=} 0.16, 0 {<=} y {<=} 0.11). The effect of melt deviation from stoichiometry on the decomposition rate of grown crystals under electron beam irradiation is shown by transmission electron microscopy. A nonuniform dopant distribution over the crystal boule cross-section is found by microprobe analysis. The Raman spectra of the samples depend on their crystallographic orientation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetic structure and properties of the compositionally complex perovskite (Y 0.2 La 0.2 Pr 0.2 Nd 0.2 Tb 0.2 )MnO 3

Large configurational disorder in compositionally complex ceramics can lead to unique functional properties that deviate from traditional rules of alloy mixing. In recent years, compositionally complex oxides (CCOs) have shown intriguing magnetic behavior including long-range order, enhanced magnetic exchange couplings, and mixed phase magnetic structures. This work focuses on how large local spin disorder affects magnetic ordering in a CCO. Specifically, we investigated the A-site alloyed perovskite, (Y 0.2 La 0.2 Pr 0.2 Nd 0.2 Tb 0.2 )MnO 3 , or (5A)MnO 3 , using a combination of bulk magnetometry, synchrotron X-ray diffraction, and temperature-dependent neutron diffraction. The five A-site ions have an average spin and ionic radius nearly equal to that of Nd 3+ ions, which minimizes structural distortions and allows for an understanding of the local spin disorder effects through a direct comparison with NdMnO 3 . Our magnetometry data show that (5A)MnO 3 exhibits two distinct phase transitions associated with the A-site and B-site sublattices, as seen in NdMnO 3 , as well as the presence of domain pinning and exchange bias at low temperature, suggesting a mixed phase magnetic ground state, as seen in other magnetic CCOs. Neutron powder diffraction shows clear long-range antiferromagnetic ordering below 67 K and refines to a Pn'ma' magnetic structure at low temperature, in excellent agreement with the well-studied behavior of NdMnO 3 . The two most notable differences in (5A)MnO 3 magnetism apparent from our data are a slight suppression of the B-site ordering temperature, which is explained by a smaller Mn–O–Mn bond angle in (5A)MnO 3 than NdMnO 3 , and the presence of a magnetic susceptibility transition above the B-site ordering, which could indicate the formation of a cluster glass but requires further study. Finally, this work demonstrates a general method of isolated investigation of size and spin disorder in CCOs and motivates future work using local structure probes to better understand the effects of nanoscale clustering and local spin disorder in magnetic CCOs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Bisimide amine cured epoxy /IME/ resins and composites. II - Ten-degree off-axis tensile and shear properties of Celion 6000/IME composites

Bisimide amines (BIAs), which are presently used as curing agents in a state-of-the-art epoxy resin, are oligomeric and polymeric mixtures. A series of composites consisting of the novel BIA-cured epoxy resin reinforced with Celion 6000 graphite fibers were fabricated and evaluated, and the ten-degree, off-axis uniaxial tensile and shear properties of these composites were determined. The use of the intralaminar shear strain-to-failure was used in the calculation of resin shear strain-to-failure. Study results indicate that several of these novel composite systems exhibit shear strain properties that are superior to those of the control composite system of the present experiments, which employed a sulfone curing agent.

Scola, D. A.↗

Combustion synthesis of CdS/reduced graphene oxide composites and their photocatalytic properties

Highlights: • CdS/reduced graphene oxide composites were prepared by a combustion method. • The phase changed from hexagonal to cubic phase by increasing the added amount of GO. • The composites showed excellent visible-light photocatalytic properties. • The plausible mechanism of photodegradation was discussed. - Abstract: CdS/reduced graphene oxide composites were synthesized by a simple one-pot combustion method using cadmium nitrate, thiourea and graphite as raw materials. The structure, morphologies, and photocatalytic properties of the as-prepared samples were studied by means of X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, Fourier transform infrared spectroscopy, photoluminescence and ultraviolet–visible spectrophotometry. The results show that the structure of CdS in as-prepared samples changes from hexagonal to cubic phase by increasing the added amount of graphene oxide. During combustion reaction, graphene oxide was reduced to reduced graphene oxide. As-obtained CdS/reduced graphene oxide composites show high visible-light photoactivities, attributed to the minimized recombination of photoinduced electrons and holes and the high surface area of reduced graphene oxide sheets.

36 MATERIALS SCIENCE↗

Investigation on Microstructure and Mechanical Properties of TA10–Q245R Composite Plate Formed by Explosive Welding

The titanium alloy TA10 and the carbon steel Q245R are welded by explosive welding, and post-weld heat treatment (PWHT) is carried out for the TA10–Q245R composite plate. Microstructure and mechanical properties of the composite plate are investigated both in as-welded (AW) condition and after PWHT, respectively. Results show that, in AW condition, the bonding interface of composite plate presents wavy morphology, and at both sides of the interface plastic deformation is generated to a certain degree. Near the interface interdiffusion zone of alloying elements exists, and no Fe-Ti intermetallic compound is produced at the interface. SEM images indicate that the tensile fracture of composite plate presents the characteristic of ductile fracture, and no defects such as gas pores or impurities are found on the surface of shear fracture. After PWHT, the interfacial microstructure of the composite plate is obviously changed. Compared with the mechanical properties of the composite plate in AW condition, both tensile strength and shear strength of the composite plate are decreased to a certain extent after PWHT. With various factors into consideration, the suitable heat treatment procedure of TA10–Q245R composite plate is determined as follows: 550 °C × 1.5 h.

36 MATERIALS SCIENCE↗

Production Mechanism, Number Concentration, Size Distribution, Chemical Composition, and Optical Properties of Sea Spray Aerosols Workshop, Summer 2012

The objective of this workshop was to address the most urgent open science questions for improved quantification of sea spray aerosol-radiation-climate interactions. Sea spray emission and its influence on global climate remains one of the most uncertain components of the aerosol-radiation-climate problem, but has received less attention than other aerosol processes (e.g. production of terrestrial secondary organic aerosols). Thus, the special emphasis was placed on the production flux of sea spray aerosol particles, their number concentration and chemical composition and properties.

54 ENVIRONMENTAL SCIENCES↗

Determination of interfacial mechanical properties of ceramic composites by the compression of micro-pillar test specimens

A novel method to determine the fiber-matrix interfacial properties of ceramic matrix composites is proposed and evaluated; where micro- pillar samples containing inclined fiber/matrix interfaces were prepared from a SiC fiber reinforced SiC matrix composites then compression-tested using the nano-indentation technique. This new test method employs a simple geometry and mitigates the uncertainties associated with complex stress state in the conventional single filament push-out method for the determination of interfacial properties. Based on the test results using samples with different interface orientations , the interfacial debond shear strength and the internal friction coefficient are explicitly determined and compared with values obtained by other test methods.

Shih, Chunghao↗

Effect of counterface material type and its topography on the tribological properties of polyimide composites

Graphite fiber reinforced polyimide composite pins were slid against seven different counterfaces to determine the effect of material type on the tribological properties of polymer composites. In addition, the effect of sliding a new pin on a pre-established transfer film was investigated. The results indicated that almost a five order of magnitude difference in composite wear rate can occur just by varying the counterface material. An attempt to make all surfaces as smooth as possible was made, but due to differences in material composition this was not possible and a range of surface roughnesses were obtained. The results indicate that the smoother the surface, the lower the composite wear rate; but that small protrusions (not discernible with arithmetic surface roughness measurements) can markedly increase wear rates. A pre-established transfer film improved both run in and steady state wear rates.

Fusaro, R. L.↗

Counterface effects on the tribological properties of polyimide composites

Graphite fiber reinforced polyimide composite pins were slid against seven different counterfaces to determine the effect of material type on the tribological properties of polymer composites. In addition, the effect of sliding a new pin on a pre-established transfer film was investigated. The results indicated that almost a five order of magnitude difference in composite wear rate can occur just by varying the counterface material. An attempt to make all surfaces as smooth as possible was made, but due to differences in material composition this was not possible and a range of surface roughnesses were obtained. The results indicate that the smoother the surface, the lower the composite wear rate; but that small protrusions (not discernible with arithmetic surface roughness measurements) can markedly increase wear rates. A pre-established transfer film improved both run in and steady state wear rates.

Fusaro, Robert L.↗

Role of different compatibilizing approaches on the microstructure and mechanical properties of polypropylene/talc composites

Since in a highly filled polymer, a major problem arises from non-uniformity of properties due to the poor dispersion of filler, the application of coupling agents have been directed to overcome this problem and also to enhance the mechanical performance of the composites by improving the adhesion at the interface. In this study, a comparison between two major coupling approaches is conducted: 1) Using PPgMA as a kind of compatibilizer which changes the nature of the matrix, 2) Using titanate coupling agent which takes action at the interface and reacts with hydroxyl groups at the inorganic filler surface, resulting in the formation of monomolecular layer on the inorganic surface to increase compatibility of filler/matrix interface. The comparison is made based on the mechanical properties of the composites by means of elastic modulus, yield stress, impact strength and percentage of strain-to-fracture and evaluation of their effects on both the dispersion and adhesion of talc plates in the matrix through the microscopy. Transmission optical microscopy (TOM) and scanning electron microscopy (SEM) are used to observe the deformation micromechanism and the fracture surface of the composites, respectively.

36 MATERIALS SCIENCE↗

Structure-property relationships in eutectic composites

The preparation of a composite material of eutectic composition directly from the molten state is investigated. The manufacture of eutectic composites by unidirectional solidification is reviewed, and it is shown how two-phase composite structures of given relative volume fraction can be produced with a range of particle sizes. Crystallographic relationships and the thermal stability of interfaces in controlled eutectic structures are examined, the mechanical behavior of aligned eutectic microstructures is discussed, and characteristics of eutectic composites having mechanical properties of engineering significance are evaluated. Specific properties of the Ni-Nb eutectic alloy are reviewed to demonstrate the effect of structure control (through directional solidification) on the mechanical response of a eutectic composite. It is noted that unidirectionally solidified eutectic composites possess highly aligned and thermally stable microstructures and also exhibit excellent combinations of strength and ductility to very high temperature levels.

Hertzberg, R. W.↗

Processing and Properties of SiC/MoSi2-SiC Composites Fabricated by Melt Infiltration

Hi-Nicalon SiC fiber reinforced MoSi2-SiC matrix composites (SiC/MoSi2-SiC) have been fabricated by the melt infiltration approach. The composite consists of approximately 60 vol%, 2-D woven BN/SiC coated Hi-Nicalon SiC fibers and approximately 40 vol% MoSi2-SiC matrix. The room temperature tensile properties and thermal conductivity of the SiC/MoSi2-SiC composites were measured and compared with those of the melt infiltrated SiC/SiC composites. The influence oi fiber architecture on tensile properties was also evaluated. Results indicate that the primary modulus, stress corresponding to deviation from linearity, and transverse thermal conductivity values for the SiC/MoSi2-SiC composites are significantly lower than those for the SiC/SiC composites. Microcracking of the matrix due to the large difference in thermal expansion between MoSi2 and SiC appears to be the reason for the lower matrix dominated properties of SiC/MoSi2-SiC composites.

Bhatt, Ramakrishna T.↗