Search NASA⌕ Search

SEARCH · Search NASA

Results for “digital interface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Isothermal thermogravimetric data acquisition analysis system

The description of an Isothermal Thermogravimetric Analysis (TGA) Data Acquisition System is presented. The system consists of software and hardware to perform a wide variety of TGA experiments. The software is written in ANSI C using Borland's Turbo C++. The hardware consists of a 486/25 MHz machine with a Capital Equipment Corp. IEEE488 interface card. The interface is to a Hewlett Packard 3497A data acquisition system using two analog input cards and a digital actuator card. The system provides for 16 TGA rigs with weight and temperature measurements from each rig. Data collection is conducted in three phases. Acquisition is done at a rapid rate during initial startup, at a slower rate during extended data collection periods, and finally at a fast rate during shutdown. Parameters controlling the rate and duration of each phase are user programmable. Furnace control (raising and lowering) is also programmable. Provision is made for automatic restart in the event of power failure or other abnormal terminations. Initial trial runs were conducted to show system stability.

Cooper, Kenneth, Jr.↗
NASA NTRS1995

PSC implementation and integration

Hardware and software design of the performance seeking control (PSC) for the NASA F-15 research aircraft are described. The hardware architecture, vehicle management system computer (VMSC), pilot interface, and PSC mode selection are discussed. The PSC software is distributed among the VMSC, central computer, digital electronic engine controls (DEEC's), and electronic air inlet controllers (EAIC's). The major PSC modules, VMSC logic, VMSC channel C memory requirements, VMSC channel C timing, and navigation control indicator (NCI) variables and where they are located are presented.

Nobbs, Steven↗
NASA NTRS1995

Wireless Headset Communication System

System combines features of pagers, walkie-talkies, and cordless telephones. Wireless headset communication system uses digital modulation on spread spectrum to avoid interference among units. Consists of base station, 4 radio/antenna modules, and as many as 16 remote units with headsets. Base station serves as network controller, audio-mixing network, and interface to such outside services as computers, telephone networks, and other base stations. Developed for use at Kennedy Space Center, system also useful in industrial maintenance, emergency operations, construction, and airport operations. Also, digital capabilities exploited; by adding bar-code readers for use in taking inventories.

Lau, Wilfred K.↗
DOE OSTI2019

Outline Shape Analysis on the Trochlear Constriction and Olecranon Fossa of the Humerus: Insights for Sex Estimation and a New Computational Tool,

Abstract Sex estimation through visual analysis of the distal humerus can contribute to establishing the biological profile of an unidentified skeletal individual. Using statistical shape modeling, the trochlear constriction open curves and olecranon fossa closed outlines of 151 humeri were digitized and analyzed. The shape configurations exhibited strikingly different degrees of sexual dimorphism when evaluated using linear discriminant analysis with leave‐one‐out cross‐validation. The trochlear constriction performed poorly, correctly classifying 63.6% of the individuals. However, the olecranon fossa showed high sexual dimorphism, presenting a 94.0% accuracy. A simpler model using only two principal components was also generated. While the accuracy is slightly inferior (88.1%), it has the advantage of being constrained to bidimensional components that were translated into morphoscopic variables within a simulator interface. This allowed us to implement the method through a web application that does not require users to be trained in landmark digitization or have knowledge of geometric morphometrics.

Ammer, Saskia↗
NASA NTRS1986

Interface Program for Reliability Predictions

CARE3MENU generates input file for CARE III program. Used to predict reliabilities of complex, redundant, fault-tolerant systems, including digital computers, aircraft, and nuclear and chemical control systems. CARE III input file often becomes complicated and not easily formatted with text editor. Provides easy interactive method of creating input file by automatically formatting set of user-supplied inputs for CARE III system. CARE3MENU provides detailed online help for most of its screen formats.

Bavuso, S. J.↗
DOE OSTI2017

Analysis of, and defense against, spurious actuations and other incorrect behaviors of digital control systems - 390

Modern digital instrumentation and control (I and C) systems offer nearly unlimited functional capability. However, the complexity of their design (including their system software and application software) is significantly higher than that of conventional, hardwired systems, to the point that it is generally impossible to demonstrate that there are no residual design errors, even when the best development and verification techniques have been applied. When activated by specific conditions, design errors could result in systematic failures, i.e., failures that occur deterministically each time and wherever an activating condition is present. Redundancy could be defeated when the same design error affects multiple channels or systems, and the activating condition affects several of these channels or systems. In the case of safety I and C systems, most of the functions are poised protection functions that must be actuated when and only when a demand situation occurs in the plant. In nuclear power plants, the most dangerous failure mode for such functions generally is failure to actuate, and many measures are taken to protect from such failure mode. This paper considers the other failure modes of safety I and C functions, and also the failure modes of the other I and C functions that are less important to safety. It is not limited to poised functions, and considers other types of functions such as regulation functions or human interface functions. It proposes a framework for analyzing and providing defense against spurious actuations and other incorrect behaviors from digital I and C systems directly interacting with the plant process or with operators: these might be useful for example to justify that design bases for reactor protection are adequate, or to ensure plant performance and availability. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2015

Domain matched epitaxial growth of (111) Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} thin films on (0001) Al{sub 2}O{sub 3} with ZnO buffer layer

Epitaxial (111) Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} (BST) thin films have been grown by pulsed laser deposition on (0001) Al{sub 2}O{sub 3} substrate with ZnO as buffer layer. The x-ray ω-2θ, Φ-scan and reciprocal space mapping indicate epitaxial nature of BST thin films. The domain matched epitaxial growth of BST thin films over ZnO buffer layer was confirmed using Fourier filtered high resolution transmission electron microscope images of the film-buffer interface. The incorporation of ZnO buffer layer effectively suppressed the lattice mismatch and promoted domain matched epitaxial growth of BST thin films. Coplanar inter digital capacitors fabricated on epitaxial (111) BST thin films show significantly improved tunable performance over polycrystalline thin films.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2019

Crystal Phase Distribution and Ferroelectricity in Ultrathin HfO 2 –ZrO 2 Bilayers

(Hf,Zr)O 2 ultrathin films are used as ferroelectric layers in emerging digital logic and nonvolatile memory devices. The ferroelectric properties of (Hf,Zr)O 2 can be improved by interface engineering, such as the formation of nanolaminates with distinct HfO 2 and ZrO 2 layers. Herein, the ferroelectric performance of HfO 2 –ZrO 2 ultrathin bilayer devices is shown to depend on the stacking order of HfO 2 and ZrO 2 , which affects the quantity of the noncentrosymmetric orthorhombic Pca 2 1 crystal phase. By combining X‐ray diffraction with a novel extended X‐ray absorption fine structure (EXAFS) analysis procedure, the orthorhombic, tetragonal, and monoclinic phase fractions are quantified for bilayers composed of 3 nm HfO 2 and 3 nm ZrO 2 . A significantly larger orthorhombic ZrO 2 phase fraction is found when ZrO 2 has an unconstrained surface during annealing, whereas the presence of a ZrO 2 interface with the substrate results in a substantial tetragonal ZrO 2 phase fraction and a 2.4× smaller remanent polarization. HfO 2 is found to be less susceptible than ZrO 2 to crystal phase templating. The methods presented herein enable mechanistic studies of ferroelectric wake‐up, fatigue, and processing effects in (Hf,Zr)O 2 films, accelerating the development of electronic devices that rely on ferroelectric oxides.

McBriarty, Martin E.↗
DOE OSTI2019

Mu2e Calorimeter Readout System

The Mu2e electromagnetic calorimeter is made of two disks of un-doped parallelepiped CsI crystals readout by SiPM. There are 674 crystals in one disk and each crystal is readout by an array of two SiPM. The readout electronics is composed of two types of modules: (1) the front-end module hosts the shaping amplifier and the high voltage linear regulator; since one front-end module is interfaced to one SiPM, a total of 2696 modules are needed for the entire calorimeter; (2) a waveform digitizer provides a further level of amplification and digitizes the SiPM signal at the sampling frequency of 200MHz with 12-bits ADC resolution; since one board digitizes the data received from 20 SiPMs, a total of 136 boards are needed. The readout system operational conditions are hostile: ionization dose of 20krads , neutron flux of 10 12 n(1MeVeq)/cm 2 , magnetic field of 1T and in vacuum level of 10 -4 Torr . A description of the readout system and qualification tests is reported.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Enabling Pulse-level Programming, Compilation, and Execution in XACC

Noisy gate-model quantum processing units (QPUs) are currently available from vendors over the cloud, and digital quantum programming approaches exist to run low-depth circuits on physical hardware. These digital representations are ultimately lowered to pulse-level instructions by vendor quantum control systems to affect unitary evolution representative of the submitted digital circuit. Vendors are beginning to open this pulse-level control system to the public via specified interfaces. Robust programming methodologies, software frameworks, and backend simulation technologies for this analog model of quantum computation will prove critical to advancing pulse-level control research and development. Prototypical use cases for this include error mitigation, optimal pulse control, and physics-inspired pulse construction. Here we present an extension to the XACC quantum-classical software framework that enables pulse-level programming for superconducting, gate-model quantum computers, and a novel, general, and extensible pulse-level simulation backend for XACC that scales on classical compute clusters via MPI. Our work enables custom backend Hamiltonian definitions and gate-level compilation to available pulses with a focus on performance and scalability. We end with a demonstration of this capability, and show how to use XACC for pertinent pulse-level programming tasks.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1972

Modification of a fuel-cell engine for control by a digital computer

A manually operated fuel-cell system was modified to be monitored and controlled by a digital computer. The purpose was to have a test item with which to study possible system-computer interface problems. The modification consisted of installing solenoid valves, circuitry, transducers, and limit switches on the system. These modifications permit computer control of load current, reactant purge, water removal, and electrolyte concentration and computer initiation of system shutdown.

Hagedorn, N. H.↗
NASA NTRS1972

Study of aircraft centered navigation, guidance, and traffic situation system concept for terminal area operation

A concept for automating the control of air traffic in the terminal area in which the primary man-machine interface is the cockpit is described. The ground and airborne inputs required for implementing this concept are discussed. Digital data link requirements of 10,000 bits per second are explained. A particular implementation of this concept including a sequencing and separation algorithm which generates flight paths and implements a natural order landing sequence is presented. Onboard computer/display avionics utilizing a traffic situation display is described. A preliminary simulation of this concept has been developed which includes a simple, efficient sequencing algorithm and a complete aircraft dynamics model. This simulated jet transport was flown through automated terminal-area traffic situations by pilots using relatively sophisticated displays, and pilot performance and observations are discussed.

Anderson, W. W.↗
NASA NTRS1974

Low cost omega navigation receiver

The development of a low cost Omega navigation receiver is discussed. Emphasis is placed on the completion and testing of a modular, multipurpose Omega receiver which utilizes a digital memory-aided, phase-locked loop to provide phase measurement data to a variety of applications interfaces. The functional units contained in the prototype device are described. The receiver is capable of receiving and storing phase measurements for up to eight Omega signals and computes two switch-selectable lines of position, displaying this navigation data in chart-recorded form.

Lilley, R. W.↗
NASA NTRS1977

Research flight software engineering and MUST, an integrated system of support tools

Consideration is given to software development to support NASA flight research. The Multipurpose User-Oriented Software Technology (MUST) program, designed to integrate digital systems into flight research, is discussed. Particular attention is given to the program's special interactive user interface, subroutine library, assemblers, compiler, automatic documentation tools, and test and simulation subsystems.

Straeter, T. A.↗
NASA NTRS1986

Acoustic characterization of composite cure

The relationship between the time evolution of ultrasonic longitudinal velocities, measured in the course of the cure of 3501-6 neat and fiber-reinforced resin, and the time evolution of the degree of cure was studied. The resin samples were placed in a mold, one side of which was a graphite plate, while the rest was made of stainless steel. After placing the mold in a press and applying a single-cycle 5-MHz pulse to the transducer bonded to the outer side of the graphite plate, the echo resulting from the resin-graphite interface and the subsequent echoes from within the resin layer were recorded with a 200-MHz, 8-bit digitizer. The degree of cure was calculated from the acoustic response, using the relationships derived by Winfree and Parker (1986). The calculated degree of cure had the expected time dependence, and the agreement between the degree of cure measured for the neat resin and the prepreg was reasonable.

Parker, F. R.↗
NASA NTRS1988

A flight test design for studying airborne applications of air to ground duplex data link communications

The Automatic En Route Air Traffic Control (AERA) and the Advanced Automated System (AAS) of the NAS plan, call for utilization of data links for such items as computer generated flight clearances, enroute minimum safe altitude warnings, sector probes, out of conformance check, automated flight services, and flow management of advisories. A major technical challenge remaining is the integration, flight testing, and validation of data link equipment and procedures in the aircraft cockpit. The flight test organizational chart, was designed to have the airplane side of data link experiments implemented in the NASA Langley Research Center (LaRC) experimental Boeing 737 airplane. This design would enable investigations into implementation of data link equipment and pilot interface, operations, and procedures. The illustrated ground system consists of a work station with links to a national weather database and a data link transceiver system. The data link transceiver system could be a Mode-S transponder, ACARS, AVSAT, or another type of radio system such as the military type HF data link. The airborne system was designed so that a data link transceiver, workstation, and touch panel could be interfaced with an input output processor to the aircraft system bus and thus have communications access to other digital airplane systems.

Scanlon, Charles H.↗
NASA NTRS1991

Toward a North American Standard for Mobile Data Services

The rapid introduction of digital mobile communications systems is an important part of the emerging digital communications scene. These developments pose both a potential problem and a challenge. On one hand, these separate market driven developments can result in an uncontrolled mixture of analog and digital links which inhibit data modem services across the mobile/Public Switched network (PSTN). On the other hand, the near coincidence of schedules for development of some of these systems, i.e., Digital Cellular, Mobile Satellite, Land Mobile Radio, and ISDN, provides an opportunity to address interoperability problems by defining interfaces, control, and service standards that are compatible among these new services. In this paper we address the problem of providing data services interoperation between mobile terminals and data devices on the PSTN. The expected data services include G3 Fax, asynchronous data, and the government's STU-3 secure voice system, and future data services such as ISDN. We address a common architecture and a limited set of issues that are key to interoperable mobile data services. We believe that common mobile data standards will both improve the quality of data service and simplify the systems for manufacturers, data users, and service providers.

Dean, Richard A.↗
DOE OSTI2022

Emulsion stereolithography and 3D printing of multimaterials and nanoscale material gradients

A functionally graded material is formed by pipetting individual micro-or-nano-litter droplets with a variety of materials including multi-nanostructured material (nanowires, carbon nanotubes, enzymes, multi-element and/or multi-color, multi-biomolecules) and UV polymerization of the flat hydrogel meniscus surface formed at the carrier fluid interface. After step-by-step droplet pipetting and subsequent layer-by-layer UV polymerization via a digital mask, the complete fabricated part without supporting layers is taken out of the carrier fluid while the un-cured micro-litter residue is conveniently suctioned out of the carrier fluid.

Zheng, Xiaoyu↗