Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

High-electron-mobility GaN grown on free-standing GaN templates by ammonia-based molecular beam epitaxy

The dependence of electron mobility on growth conditions and threading dislocation density (TDD) was studied for n{sup −}-GaN layers grown by ammonia-based molecular beam epitaxy. Electron mobility was found to strongly depend on TDD, growth temperature, and Si-doping concentration. Temperature-dependent Hall data were fit to established transport and charge-balance equations. Dislocation scattering was analyzed over a wide range of TDDs (∼2 × 10{sup 6} cm{sup −2} to ∼2 × 10{sup 10} cm{sup −2}) on GaN films grown under similar conditions. A correlation between TDD and fitted acceptor states was observed, corresponding to an acceptor state for almost every c lattice translation along each threading dislocation. Optimized GaN growth on free-standing GaN templates with a low TDD (∼2 × 10{sup 6} cm{sup −2}) resulted in electron mobilities of 1265 cm{sup 2}/Vs at 296 K and 3327 cm{sup 2}/Vs at 113 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

On deformation twinning in a 17.5%Mn-TWIP steel: A physically-based phenomenological model

TWinning Induced Plasticity (TWIP) steel is a typical representative of the 2nd generation of advanced high strength steel (AHSS) which exhibits a combination of high strength and excellent ductility due to the twinning mechanisms. This paper discusses the principal features of deformation twinning in faced-centered cubic austenitic steels and shows how a physiscally-based macroscopic model can be derived from microscopic considerations. In fact, a dislocation-based phenomenological model, with internal state variables such as dislocation density and micro-twins volume fraction representing the microstructure evolution during deformation process, is proposed to describe the deformation behavior of TWIP steels. The contribution of this work is the incorporation of a physically-based twin’s nucleation and volume fraction evolution model in a conventional dislocation-based approach. Microstructural level investigations, using scanning electron microscope (SEM) and transmission electron microscope (TEM) techniques, for the TWIP steel Fe–17.5 wt.% Mn–1.4 wt.% Al- 0.56 wt.% C, are used to validate and verify modeling assumptions. The model could be regarded as a semi-phenomenological approach with sufficient links between microstructure and overall properties and therefore offers good predictive capabilities. Its simplicity also allows a modular implementation in finite element-based metal forming simulations.

36 MATERIALS SCIENCE↗

Dislocation Content Measured Via 3D HR-EBSD Near a Grain Boundary in an AlCu Oligocrystal

Interactions between dislocations and grain boundaries are poorly understood and crucial to mesoscale plasticity modeling. Much of our understanding of dislocation-grain boundary interaction comes from atomistic simulations and TEM studies, both of which are extremely limited in scale. High angular resolution EBSD-based continuum dislocation microscopy provides a way of measuring dislocation activity at length scales and accuracies relevant to crystal plasticity, but it is limited as a two-dimensional technique, meaning the character of the grain boundary and the complete dislocation activity is difficult to recover. However, the commercialization of plasma FIB dual-beam microscopes have made 3D EBSD studies all the more feasible. The objective of this work is to apply high angular resolution cross correlation EBSD to a 3D EBSD data set collected by serial sectioning in a FIB to characterize dislocation interaction with a grain boundary. Three dimensional high angular resolution cross correlation EBSD analysis was applied to an AlCu oligocrystal to measure dislocation densities around a grain boundary. Distortion derivatives associated with the plasma FIB serial sectioning were higher than expected, possibly due to geometric uncertainty between layers. Future work will focus on mitigating the geometric uncertainty and examining more regions of interest along the grain boundary to glean information on dislocation-grain boundary interaction.

Ruggles, Timothy↗

Distribution of dislocations in nanostructured bainite

The dislocation density in ferrite and austenite of a bainitic microstructure obtained by transformation at very low temperature (300 C) has been determined using transmission electron microscopy. Observations revealed that bainitic ferrite plates consist of two distinctive regions with different substructures. A central region in the ferrite plate is observed with dislocations that may result from lattice-invariant deformation at the earlier stage of bainite growth. As plastic deformation occurs in the surrounding austenite to accommodate the transformation strain as growth progresses, the Ferrite/Austenite interface has also a very distinctive dislocation profile. In addition, atom-probe tomography suggested that dislocation tangles observed in the vicinity of the ferrite/austenite interface might trap higher amount of carbon than single dislocations inside the bainitic ferrite plate.

36 MATERIALS SCIENCE↗

A comparison of adiabatic shear bands in wrought and additively manufactured 316L stainless steel using nanoindentation and electron backscatter diffraction

The resistance of stainless steels to shear localization is dependent on processing and microstructure. The amount of research evaluating the shear response of additively manufactured (AM) stainless steels compared to traditionally manufactured ones is limited. To address this gap, experiments were performed on directed energy deposition AM as-built and wrought 316L stainless steel using a forced shear technique with a hat-shaped specimen and a Split-Hopkinson pressure bar. The resulting adiabatic shear bands were characterized with electron backscatter diffraction (EBSD) and nanoindentation to quantify the changes in microstructure and deformation hardening across shear band regions and between the wrought and AM materials. Despite significant differences between the wrought and AM materials including the forced shear response, the postmortem states of work hardening due to the shear band deformation are nearly the same. The maximum nanoindentation stresses occurred in the shear band center with similar magnitudes and only minor differences away from the shear band. Although EBSD data cannot be resolved in the shear band center, misorientation trends, particularly grain reference orientation deviation, were found to closely resemble nanoindentation trends. In conclusion, the combination of EBSD misorientation and nanoindentation, which are linked through changes in dislocation density, is a viable protocol to quantify local changes to macroscopically applied deformation.

36 MATERIALS SCIENCE↗

Micro-beam bending of FCC bicrystals: A comparison between defect dynamics simulations and experiments

To understand the role of the grain boundary (GB) in plasticity at small scale, a concurrently coupled mesoscale plasticity model was developed to simulate micro-bending of bicrystalline micron-sized beams. By coupling dislocation dynamics (DD) with a finite element model (FEM), a novel defect dynamics model provides the means to investigate intricate interactions between dislocations and GBs under various loading conditions. Our simulations of micro-bending agree well with corresponding micro-bending experiments, and they show that mechanical response of bicrystals could have not only hardening but also softening depending on the characters of the GB. In addition, changing the location of the GB in the microbeams results in different mechanical responses; GBs located at the neutral plane show softening compared to single crystals, while inclined GBs located halfway along the length of the beam show little effect. In conclusion, simulation results could provide a clear picture on detailed dislocation-GB interactions, and quantitative resolved shear stress analysis supplemented by dislocation density distribution is used to analyze the mechanical response of bicrystalline samples.

36 MATERIALS SCIENCE↗

Structural properties of InN films grown on O-face ZnO(0001) by plasma-assisted molecular beam epitaxy

We study the impact of substrate temperature and layer thickness on the morphological and structural properties of InN films directly grown on O-face ZnO(0001) substrates by plasma-assisted molecular beam epitaxy. With increasing substrate temperature, an interfacial reaction between InN and ZnO takes place that eventually results in the formation of cubic In{sub 2}O{sub 3} and voids. The properties of the InN films, however, are found to be unaffected by this reaction for substrate temperatures less than 550 deg. C. In fact, both the morphological and the structural quality of InN improve with increasing substrate temperature in the range from 350 to 500 deg. C. High quality films with low threading dislocation densities are demonstrated.

36 MATERIALS SCIENCE↗

Effect of irradiation on terminal solid solubility of hydrogen in Zr-2.5Nb - 2016-0044

Knowledge of the temperature dependence of hydrogen solubility is used to define the conditions necessary for brittle hydrides to be present in reactor components during service. The terminal solid solubility (TSS) of hydrogen is affected by several factors, including irradiation, cold work, and decomposition of the β phase in Zr-2.5Nb. TSS temperatures for specimens irradiated in Osiris, Halden, and CANDU{sup R} reactors are reported. TSS was measured on Zr-2.5Nb specimens using differential scanning calorimetry (DSC) to complete four heatup/cool-down cycles (heat to a peak temperature and cool to room temperature at a rate of 10 deg. C/min) followed by a 1-h anneal at 500 deg. C, and then four more heat-up/cool-down cycles. As with Zircaloy, irradiation slightly decreases the TSS temperatures, but subsequent annealing increases them. These changes are attributed to an initial effect of irradiation damage and reconstitution of the β phase and reversal of these effects by annealing, as indicated by X-ray diffraction data showing reduced dislocation density and higher β-phase volume fraction after the specimens were annealed. (authors)

36 MATERIALS SCIENCE↗

Effect of alloying elements, cold work, and hydrogen on the irradiation-induced growth behavior of zirconium alloy variants - 2016-0040

In-reactor dimensional changes in zirconium-based alloys result from a complex interplay of many factors, such as (1) alloy type and composition, including the addition of elements such as niobium, iron, and tin; (2) fabrication process, including cold work, texture, and residual stresses; (3) irradiation temperature; and (4) hydrogen levels. In many cases, the observed dimensional changes in light water reactor fuel-assembly components-especially at high exposures-cannot be fully explained based on current growth and creep models. Therefore, a systematic approach was taken in this multi-year (2005-2011) Nuclear Fuel Industry Research Program investigation. The objective was to measure stress-free irradiation-induced growth (IIG) of specially fabricated alloys through irradiation under controlled conditions in the BOR-60 fast-flux test reactor up to a high fluence of approximately 2X10{sup 26} m{sup -2} (E>1 MeV)-equivalent to maximum of approximately 37 dpa exposure-followed by postirradiation examinations (PIEs). Irradiation temperature was within a narrow temperature range (320±10 deg. C). The PIEs included dimensional-change and microhardness measurements, metallography and hydride etching, and scanning transmission electron microscopy (STEM) or transmission electron microscopy (TEM). All irradiation samples (typically flat rectangular coupons or curvilinear cutouts of cladding tubes sized 35 by 6.5 by 0.8 mm) were pre-filmed to avoid the uptake of impurity hydrogen from sodium-cooled BOR-60. A wide variety of samples representing standard LWR cladding alloys with and without pre-hydriding (approximately 116 to approximately 718 ppm) as well as special compositions with iron contents (100 to 4,000 ppm) were irradiated. The irradiation in BOR-60 was done in five different stages (eight micro-cycles) and lasted approximately 18 months with interim and final growth measurements made using a high precision-length measurement device. Results of the extensive investigation include: significant effects of Fe, Nb, and hydrogen additions; quantification of growth rates from low to very high fluences (dpas); measurement of volume changes; and correlation of growth with -component dislocation densities. (authors)

36 MATERIALS SCIENCE↗

Scattering induced by Al segregation in AlGaN/GaN heterostructures

The effect of Al segregation near dislocations on the mobility of two-dimensional electron gas in AlGaN/GaN heterostructure-based high-electron-mobility transistors was investigated. Exponentially varied composition fluctuation was effective in describing Al segregation near dislocations when calculating scattering behavior. Mobility, which was limited by Al segregation surrounding dislocation lines, was calculated to be in the order of 10{sup 3} cm{sup 2}/Vs to 10{sup 6} cm{sup 2}/Vs. Results indicated that the mobility in AlGaN/GaN heterojunction was enhanced upon the reduction of dislocation density at low temperature. This study contributes to generating higher electron mobility in AlGaN/GaN heterojunctions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

X-ray topography using the forward transmitted beam under multiple-beam diffraction conditions

X-ray topographs are taken for a sapphire wafer with the [0001] surface normal, as an example, by forward transmitted synchrotron x-ray beams combined with two-dimensional electronic arrays in the x-ray detector having a spatial resolution of 1 μm. They exhibit no shape deformation and no position shift of the dislocation lines on the topographs. Since the topography is performed under multiple-beam diffraction conditions, the topographic images of a single diffraction (two-wave approximation condition) or plural diffractions (six-wave approximation condition) can be recorded without large specimen position changes. As usual Lang topographs, it is possible to determine the Burgers vector of each dislocation line. Because of high parallelism of the incoming x-rays and linear sensitivity of the electronic arrays to the incident x-rays, the present technique can be used to visualize individual dislocations in single crystals of the dislocation density as high as 1 × 10{sup 5} cm{sup −2}.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Relationship between dislocations and residual stresses in cold-drawn pearlitic steel analyzed by energy-dispersive X-ray diffraction

We analyzed the dislocation distribution of cold-drawn pearlitic-steel wire by using the line-profile analysis based on the energy dispersive X-ray diffraction (EDXD). Although this line-profile analysis requires a high resolution in reciprocal space, the resolution for EDXD is generally poor due to the energy resolution of the detector. Our analysis demonstrated that the resolution in the reciprocal space can be maximized at small scattering angles. Using the line-profile analysis based on the EDXD, the microstructural parameters such as the crystallite size and the dislocation density of the ferrite phase in the pearlitic steel were successfully analyzed. In addition, the distribution of the residual stress of the ferrite phase of a pearlitic steel wire was also analyzed using the EDXD measurement. - Highlights: • Energy dispersive X-ray diffraction is applied to the line-profile analysis. • Distribution of dislocations in ferrite in the pearlitic steel wire is analyzed. • Relationship between dislocations and residual stress is discussed.

36 MATERIALS SCIENCE↗

Basis for the Bauschinger effect in copper single crystals: changes in the long-range internal stress with reverse deformation

In this study, the long-range internal stresses (LRIS) associated with the Bauschinger effect were investigated using synchrotron X-ray microbeam diffraction and reversed deformation experiments. [100]-oriented Cu single crystals were deformed in compression to approximately -0.3 true strain, followed by tension to a strain of approximately +0.02. Two conclusions are arrived at from this work: First, the LRIS are confirmed in this work to be small relative to the applied stress both before and after reversal. Second, the LRIS persist after 2% reversed strain despite a significant drop in the overall dislocation density by dynamic recovery. This appears to satisfy the necessary condition for LRIS to significantly contribute to a Bauschinger effect in materials. Lastly, the pronounced Bauschinger effect in Cu is probably best rationalized by a combination of both the LRIS and the Orowan–Sleeswyk model that relies on a non-uniform distribution of dislocation obstacles without a substantial LRIS.

36 MATERIALS SCIENCE↗

Effect of Sm-Rich Phase on Corrosion Behavior of Hot-Extruded AZ31-1.5Sm Magnesium Alloy

The effects of Sm on the corrosion and microstructure behavior of hot-extruded AZ31 magnesium alloy were investigated by SEM, TEM, weight loss analysis, and electrochemical measurements. The results indicated that granular Al{sub 2}Sm phase ~ 4 μm in size in the hot-extruded AZ31 magnesium alloy modified with 1.5 wt.% Sm leads to significant grain refinement. The corrosion rate decreased from 15.98 × 10{sup −4} to 11.19 × 10{sup −4} g cm{sup −2} h{sup −1} in the transverse section and from 8.57 × 10{sup −4} to 6.20 × 10{sup −4} g cm{sup −2} h{sup −1} in the longitudinal section. Compared to the unmodified alloy, the corrosion potential of the Sm-modified alloy in the transverse and longitudinal sections increased by 98 and 62 mV, respectively, and the R{sub ct} value (charge transfer resistance) in the transverse and longitudinal sections of the modified alloy increased from 1764 and 1756 to 2928 and 2408 Ω cm{sup 2}, respectively. The results showed that the corrosion resistance of hot-extruded AZ31 magnesium alloy was significantly improved by Sm addition due to the grain refinement, the decreased dislocation density, and the suppression of micro-galvanic corrosion caused by Al-Sm-(Mn) intermetallic compounds.

36 MATERIALS SCIENCE↗

Electron channeling contrast imaging investigation of stacking fault pyramids in GaP on Si nucleation layers

Thin gallium phosphide layers were deposited on (0 0 1) Silicon surfaces via organometallic vapor phase epitaxy and characterized by electron channeling contrast imaging (ECCI). Stacking fault pyramids at a density of up to 6 x 10 7 cm -2 were identified in the GaP nucleation layer by varying the diffraction conditions. We show that these defects originate at the GaP/Si interface and propagate on all four {1 1 1} planes. We observed that such stacking fault pyramids interact with the gliding of misfit dislocations during lattice-mismatched growth and enhance the threading dislocation density. The initial pulsing of TEGa and TBP during the nucleation of GaP on Silicon has been found to strongly influence the formation of those pyramidal defects. Changing the number of pulse cycles allowed us to lower their density by two orders of magnitude from 6 x 10 7 cm -2 to 4 x 10 5 cm -2 .

36 MATERIALS SCIENCE↗

Characterizing defect structures in AM steel using direct electron detection EBSD

The mechanical properties of additive and traditionally manufactured alloys are largely dependent on the characteristics and distribution of dislocation cell networks that develop during the fabrication process. This work demonstrates the ability to quantitatively characterize these dislocation structures by high angular resolution electron backscatter diffraction analysis using a direct electron detector. The defect structures are characterized in terms of the geometrically necessary dislocation density and the associated Burgers vector and line direction. Furthermore, the results are discussed in terms of potential defect formation mechanisms.

36 MATERIALS SCIENCE↗

Influence of dislocations and twin walls in BaTiO 3 on the voltage-controlled switching of perpendicular magnetization

In this work, we investigate the influence of dislocations and twin walls in BaTiO 3 on its ferroelectric response and the resulting effect on the perpendicular magnetic anisotropy (PMA) of a strain-coupled [Co\Ni] n film. A dense twinned structure in conjunction with a high dislocation density significantly reduces the converse piezoelectric effect of BaTiO 3 by hindering the propagation of newly nucleated domains with an applied electric field. This, in turn, results in a modest reduction of the PMA of the ferromagnetic layer. On the other hand, the ferroelectric polarization reorients from [100] to [001] direction in a dislocation-free BaTiO 3 , inducing the maximum achievable in-plane compressive strain of 1.1%. A large fraction of this uniaxial strain is transferred to the magnetoelastically coupled ferromagnetic layers whose magnetization switches to in plane via the inverse magnetostriction effect. This work reveals the critical role of the interplay between twin walls and dislocations within a ferroelectric substrate in the performance of multiferroic heterostructures and provides insight into the development of highly energy-efficient magnetoelectric devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗