Search NASA⌕ Search

SEARCH · Search NASA

Results for “drying methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Retrieved Number Concentration of Cloud Condensation Nuclei (RNCCN) Profile Value-Added Product Report

The cloud condensation nuclei (CCN) concentration at cloud base is the most relevant measure of the aerosol that influences droplet formation in clouds. Since the CCN concentration depends on supersaturation, a more general measure of the CCN concentration is the CCN spectrum (values at multiple supersaturations). The CCN spectrum is now measured at the surface at several U.S. Department of Energy Atmospheric Radiation Measurement (ARM) user facility observatories and by the ARM Mobile Facility (AMF) but is not measured at the cloud base. Rather than rely on expensive aircraft measurements for all studies of aerosol effects on clouds, a way to project CCN observations made at the surface to cloud base is needed. Remote sensing of aerosol extinction provides information about the vertical profile of the aerosol but cannot be directly related to the CCN concentration because the aerosol extinction is strongly influenced by humidification, particularly near cloud base. Ghan and Collins (2004) and Ghan et al. (2006) propose a method to remove the influence of humidification from the extinction profiles and tie the “dry extinction” retrieval to the surface CCN concentration, thus estimating the CCN profile. This methodology has been implemented as ARM’s Retrieved Number Concentration of CCN (RNCCN) Profile Value-Added Product (VAP).

54 ENVIRONMENTAL SCIENCES↗

Development and Comparison of Ground and Satellite-based Retrievals of Cirrus Cloud Physical Properties

This report is the final update on ARM research conducted at DRI through May of 2006. A relatively minor amount of work was done after May, and last month (November), two journal papers partially funded by this project were published. The other investigator on this project, Dr. Bob d'Entremont, will be submitting his report in February 2007 when his no-cost extension expires. The main developments for this period, which concludes most of the DRI research on this project, are as follows: (1) Further development of a retrieval method for cirrus cloud ice particle effective diameter (De) and ice water path (IWP) using terrestrial radiances measured from satellites; (2) Revision and publication of the journal article 'Testing and Comparing the Modified Anomalous Diffraction Approximation'; and (3) Revision and publication of our radar retrieval method for IWC and snowfall rate.

54 ENVIRONMENTAL SCIENCES↗

Efficient volatile metal removal from low rank coal in gasification, combustion, and processing systems and methods

Efficient coal pre-processing systems (69) integrated with gasification, oxy-combustion, and power plant systems include a drying chamber (28), a volatile metal removal chamber (30), recirculated gases, including recycled carbon dioxide (21), nitrogen (6), and gaseous exhaust (60) for increasing the efficiencies and lowering emissions in various coal processing systems.

01 COAL, LIGNITE, AND PEAT↗

Method for the synthesis of iron hexacyanoferrate

A method is provided for synthesizing iron hexacyanoferrate (FeHCF). The method forms a first solution of a ferrocyanide source [A4Fe(CN)6.PH2O] material dissolved in a first solvent, where “A” is an alkali metal ion. A second solution is formed of a Fe(II) source dissolved in a second solvent. A reducing agent is added and, optionally, an alkali metal salt. The first and second solutions may be purged with an inert gas. The second solution is combined with the first solution to form a third solution in a low oxygen environment. The third solution is agitated in a low oxygen environment, and AX+1Fe2(CN)6.ZH2O is formed, where X is in the range of 0 to 1. The method isolates the AX+1Fe2(CN)6.ZH2O from the third solution, and dries the AX+1Fe2(CN)6.ZH2O under vacuum at a temperature greater than 60 degrees C.

25 ENERGY STORAGE↗

Methods of Heat-Exchange Intensification in NPP Equipment

The aims and problems of research on the means for intensifying heat exchange in the equipment of nuclear power plants are examined: nuclear reactors, steam generators, turbine condensers, heat-exchangers of dry water cooling towers, intermediate separators-steam superheaters of turbines, heat-exchange apparatus of safety systems, turbo-electro-generators, oil coolers, feed-water heaters. Methods of identifying heat-exchange are analyzed: different types of finning, turbulence generators and swirlers of one- and two-phase flows, coating on heating surfaces, systems with mixed flow. Computational recommendations are made for determining the intensity of heat emission from promising types of heat-exchange surfaces: bundles of lowfinned tubes and spiral coils.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Advanced SMRs Using S-CO2 Power Conversion with Dry Cooling

This report concludes the LDRD entitled "Advanced SMRs using S-CO2 Power Conversion with Dry Cooling." The goal of this project was to demonstrate the feasibility of using sCO 2 as the working fluid in a dry-cooled natural circulation loop. The reason for doing this is to demonstrate that such a loop could be utilized in small modular reactors (SMRs) as a method for (a) passively removing decay heat from the reactor and (b) cooling the reactor without using the copious amounts of water needed for wet-cooled reactors. The dry-cooling aspect of this work is possible due to the working conditions of a sCO 2 Brayton power conversion cycle. The loop was designed, built, and operated over the three-year life of the LDRD project. This report outlines some of the key accomplishments and some of the future work that we are continuing to try to complete in the future. A more comprehensive report will be completed and submitted in the Fall of 2015.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Nonlinear Ultrasonic Diagnosis and Prognosis of ASR Damage in Dry Cask Storage

Alkali-silica reaction (ASR) is a deleterious chemical process that may occur in cement-based materials such as mortars and concretes, where the hydroxyl ions in the highly alkaline pore solution attack the siloxane groups in the siliceous minerals in the aggregates. The reaction produces a cross-linked alkali-silica gel. The ASR gel swells in the presence of water. Expansion of the gel results in cracking when the swelling-induced stress exceeds the fracture toughness of the concrete. As the ASR continues, cracks may grow and eventually coalesce, which results in reduced service life and a decrease safety of concrete structures. Since concrete is widely used as a critical structural component in dry cask storage of used nuclear fuels, ASR damage poses a significant threat to the sustainability of long term dry cask storage systems. Therefore, techniques for effectively detecting, managing and mitigating ASR damage are needed. Currently, there are no nondestructive methods to accurately detect ASR damage in existing concrete structures. The only current way of accurately assessing ASR damage is to drill a core from an existing structure, and conduct microscopy on this drilled cylindrical core. Clearly, such a practice is not applicable to dry cask storage systems. To meet these needs, this research is aimed at developing (1) a suite of nonlinear ultrasonic quantitative nondestructive evaluation (QNDE) techniques to characterize ASR damage, and (2) a physics-based model for ASR damage evolution using the QNDE data. Outcomes of this research will provide a nondestructive diagnostic tool to evaluate the extent of the ASR damage, and a prognostic tool to estimate the future reliability and safety of the concrete structures in dry cask storage systems

42 ENGINEERING↗

Developing generic design alternatives for dry storage of used nuclear fuel at an interim storage facility - 15480

The Department of Energy (DOE) is beginning to lay the groundwork for implementing interim storage of used nuclear fuel (UNF) as recommended by the Blue Ribbon Commission on America's Nuclear Future in their report to the Secretary of Energy published on January 26, 2012. These plans include activities to 1) establish one or more Interim Storage Facilities (ISF) using consent-based siting, and 2) prepare for large-scale transport of UNF. The Administration released its Strategy for the Management and Disposal of Used Nuclear Fuel and High-Level Radioactive Waste (Strategy) on January 11, 2013. The Strategy includes a phased, adaptive, and consent-based approach to siting and implementing a comprehensive management and disposal system. The Strategy calls for an operational Pilot ISF by 2021, a Larger ISF by 2025, and a geological repository by 2048. The DOE Nuclear Fuels Storage and Transportation Planning Project (NFST) prepared a report in April 2013 titled, -A Project Concept for Nuclear Fuels Storage and Transportation.- This report developed the functions and requirements necessary for development of a Pilot and Larger ISF to meet the framework outlined in the Strategy as follows: - The UNF inventory is limited for the Pilot and Larger ISF as described in the Strategy. - It is assumed that bare fuel will be received in reusable transportation casks in significant quantities for the larger ISF and will not be solely limited to the receipt of fuel in dry storage canister (DSC) as is the Pilot ISF. This assumption was made because the method for accepting UNF from the utilities once the larger ISF begins operating has not yet been decided. - UNF storage alternative concepts identified in previous reports must be more fully developed to support alternative analysis. The purpose of this topic is to report on the development of the generic design alternatives that have been evaluated for the receipt and storage of the UNF at the initial Pilot ISF and Larger ISF. The generic design alternatives have been developed over the past few months by collaboration between the DOE and industry experts experienced in UNF facilities. The design alternatives will enable volunteer host communities to investigate generic design alternatives that could be fully developed for a site-specific location based on their unique design requirements. The design alternatives provide flexibility for additional capabilities to be developed and executed in a modular fashion such that expansion from a Pilot ISF to a Larger ISF could be achieved in an orderly manner. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Optimized Slurries for Spray Drying: Different Approaches to Obtain Homogeneous and Deformable Alumina-Zirconia Granules

Spray drying is widely used for producing granulated feed materials for compaction process, which is the current industrial method for manufacturing alumina-zirconia femoral heads. The optimization of the granules compaction behavior requires the control of the slurry rheology. Moreover, for a dual-phase ceramic suspension, the even phase distribution has to be kept through the atomization step. Here we present two approaches addressing the key issues involved in the atomization of a composite system. Alumina-10 vol % zirconia powders were prepared by either a powder mixing route, or by the surface modification of a commercial α-alumina powder with a zirconium salt. Slurries from both powders were spray dried. The correlation between slurry rheology and pH, granules morphology and sintered microstructures was here investigated and discussed on the ground of the two feed materials characteristics. The processing conditions were optimized to obtain dense and homogeneous alumina-zirconia micro-nano composites by both processing routes.

36 MATERIALS SCIENCE↗

A Novel Laser 3D Printing Method for the Advanced Manufacturing of Protonic Ceramics

Protonic ceramics (PCs) with high proton conductivity at intermediate temperatures (300–600 °C) have attracted many applications in energy conversion and storage devices such as PC fuel/electrolysis cells, PC membrane reactors, hydrogen pump, hydrogen or water-permeable membranes, and gas sensors. One of the essential steps for fulfilling the practical utilization of these intermediate-temperature PC energy devices is the successful development of advanced manufacturing methods for cost-effectively and rapidly fabricating them with high energy density and efficiency in a customized demand. In this work, we developed a new laser 3D printing (L3DP) technique by integrating digital microextrusion-based 3D printing and precise and rapid laser processing (sintering, drying, cutting, and polishing), which showed the capability of manufacturing PCs with desired complex geometries, crystal structures, and microstructures. The L3DP method allowed the fabrication of PC parts such as pellets, cylinders, cones, films, straight/lobed tubes with sealed endings, microchannel membranes, and half cells for assembling PC energy devices. The preliminary measurement of the L3DP electrolyte film showed a high proton conductivity of ≈7 × 10−3 S/cm. This L3DP technique not only demonstrated the potential to bring the PCs into practical use but also made it possible for the rapid direct digital manufacturing of ceramic-based devices.

08 HYDROGEN↗

A Facile Degumming Method of Kenaf Fibers Using Deep Eutectic Solution

An eco-friendly and effective degumming method needed to be developed for producing kenaf bast fibers. As such, this study devised a novel deep eutectic solvent (DES) method coupled with microwave and alkaline-ultrasonic treatment. The novel method could effectively remove the gummy matters, providing a smooth and clean fiber surface. The properties of the fibers were assessed including chemical compositions, surface structure, crystallinity index (66.68%) and thermal properties. The residual gum content (9.419%), fiber fineness (4.125tex), breaking tenacity (13.650 cn/tex) of the refined dry fibers produced by the novel treatment were comparable with the fibers produced by the traditional two-step alkali boiling method. Besides, the novel method could reduce the usage of chemical, water and time by 48.9%, by 66.7% and 66.8%, respectively. These results revealed that the novel combined DES pretreatment is a practical and feasible pretreatment method for kenaf bast degumming, demonstrating its facile, green energy-saving and fast properties in the degumming process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sputter sample preparation for ion beam delivery of radium-223 at ATLAS

A radium-223 ion beam was delivered to an experiment from the electron cyclotron resonance ion source, ECR2, at the Argonne Tandem Linac Accelerator System (ATLAS). Here, the radium-223 material was in a nitrate salt form within a vial, prior to being converted to a usable sputter sample. The sputter sample was produced using a new sample preparation method, where the radium nitrate was dissolved into a solution and pipetted onto pressed aluminum powder. This sample was then allowed to dry, distributing the radium-223 material throughout the sputter sample. Ion source operation using the radium sputter sample is described with the operating parameters listed. The intensity and energy requirements for this ion beam were 1 × 10 6 particles/s and 1.07 GeV, respectively. Because the intensity is relatively low compared to most experiments at ATLAS, previously developed accelerator mass spectrometry methods were used Scott et al. to avoid the need for tuning of the low-intensity beam of interest. Handling of the radium material, as well as loading and unloading of the sputter sample from ECR2, required collaboration with Health Physics. Procedures were used and dry runs were carried out before, during, and after the experiment to ensure the safety of the workers. The processes used and lessons learned are described within.

07 ISOTOPE AND RADIATION SOURCES↗

Nitrogen-doped carbon aerogels for electrical energy storage

Disclosed here is a method for making a nitrogen-doped carbon aerogel, comprising: preparing a reaction mixture comprising formaldehyde, at least one nitrogen-containing resorcinol analog, at least one catalyst, and at least one solvent; curing the reaction mixture to produce a wet gel; drying the wet gel to produce a dry gel; and thermally annealing the dry gel to produce the nitrogen-doped carbon aerogel. Also disclosed is a nitrogen-doped carbon aerogel obtained according to the method and a supercapacitor comprising the nitrogen-doped carbon aerogel.

25 ENERGY STORAGE↗

Hydraulic conductance, resistance, and resilience: how leaves of a tropical epiphyte respond to drought

Premise Because of its broad range in the neotropical rainforest and within tree canopies, the tank bromeliad Guzmania monostachia was investigated as a model of how varying leaf hydraulic conductance ( K leaf ) could help plants resist and recover from episodic drought. The two pathways of K leaf , inside and outside the xylem, were also examined to determine the sites and causes of major hydraulic resistances within the leaf. Methods We measured leaf hydraulic conductance for plants in the field and laboratory under wet, dry, and rewetted conditions and applied physiological, anatomical, and gene expression analysis with modeling to investigate changes in K leaf . Results After 7 d with no rain in the field or 14 days with no water in the glasshouse, K leaf decreased by 50% yet increased to hydrated values within 4 d of tank refilling. Staining to detect embolism combined with modeling indicated that changes outside the xylem were of greater importance to K leaf than were changes inside the xylem and were associated with changes in intercellular air spaces (aerenchyma), aquaporin expression and inhibition, and cuticular conductance. Conclusions Low values for all conductances during drying, particularly in pathways outside the xylem, lead to hydraulic resilience for this species and may also contribute to its broad environmental tolerances.

North, Gretchen B.↗

Crystalline Loading of Lipophilic Coenzyme Q10 Pharmaceuticals within Conjugated Carbon Aerogel Derivatives

Low-density aerogel materials currently are being considered for applications in controlling the rate of release for small-molecule pharmaceuticals in vivo. In particular, silica (SiO2) aerogels are an intriguing platform for controlling both the absolute amount of drug loading, but also the crystalline state of small molecule pharmaceuticals has been shown to affect drug release kinetics. To date, loading silica aerogel materials with crystalline pharmaceuticals typically require dissolving small molecules in a supercritical solvent (i.e., CO2) before drying to recover the aerogel/drug composite. Here we demonstrate a simple and low-cost method for controlling the crystallinity of the model drug coenzyme Q10 (CoQ10) within carbon aerogel materials by rationally controlling the chemical microstructure of the aerogel to exhibit ?-conjugated (sp2) chemical bonding. In particular, both pyrolyzed graphene and nanodiamond aerogels exhibit enhanced intrinsic drug loading capacity and CoQ10 crystallinity over a broad range of sp2 surface-curvature. In contrast, amorphous carbon aerogel materials are observed to load CoQ10 pharmaceuticals with strictly amorphous microstructure.

Lim, Mathew↗

Additive manufacturing and mechanical characterization of high density fully stabilized zirconia

Mechanical properties of additively manufactured 8 mol% yttria-stabilized zirconia (8YSZ) parts were extensively studied for the first time. A novel freeform extrusion fabrication process, called Ceramic On-Demand Extrusion (CODE), was employed to deposit an aqueous viscous suspension (~50 vol% solids loading) of fully stabilized zirconia powder in a layer-by-layer fashion. Each layer was exposed to infrared radiation after deposition to attain partial solidification due to drying. Before exposure, the layer was surrounded by oil to preclude non-uniform evaporation, which could cause warpage and crack formation. After the fabrication process was completed, the parts were humid-dried in an environmental chamber and densified by sintering under atmospheric pressure. Here standard test methods were employed to examine the properties of sintered parts including density, Vickers hardness, fracture toughness, Young's modulus, and flexural strength. Microstructural evaluation was also performed to observe the microstructural morphology and measure grain size. The results indicate that the properties of 8YSZ parts produced by the CODE process match those obtained by conventional fabrication techniques.

36 MATERIALS SCIENCE↗

Efficient preparation of nanocrystalline anatase TiO{sub 2} and V/TiO{sub 2} thin layers using microwave drying and/or microwave calcination technique

This study has demonstrated that the synthesis of TiO{sub 2} and V/TiO{sub 2} thin layers may be significantly improved and extended if microwave energy is employed during the drying and/or calcination step. Thin nanoparticulate titania layers were prepared via the sol-gel method using titanium n-butoxide as a precursor. As prepared films were then analyzed by means of various characterization techniques (Raman spectroscopy, UV/Vis, AFM, XPS) in order to determine their functional properties. The photocatalytic activities of prepared layers were quantified by the decoloring rate of Rhodamine B. All thermal treatments in microwave field were done in the same manner, by using an IR pyrometer in the microwave oven and monitoring the temperature of the heating. Nevertheless the microwave and thermally prepared materials were different. This in turn may lead to differences in their functional and also photocatalytic properties. - Graphical abstract: This study has demonstrated that the synthesis of thin layers may be improved and extended if microwave energy is employed during the preparation process. Microwave processing has the potential to reduce the time, cost and energy input for the production of thin layers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗