SEARCH · Search NASA

Results for “flat models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Interior noise analysis and control for light aircraft

This paper describes experimental and analytical studies of the interior noise of twin-engine, propeller-driven, light aircraft. Experimental results indicate that interior noise levels due to propeller noise can be reduced by reduction of engine rpm at constant airspeed (about 3 dB), by synchronization of the twin engines/propellers (up to 12 dB), and by increasing the distances from propeller tip to fuselage. The analytical model described uses modal methods and incorporates the flat-sided geometrical and skin-stringer structural features of light aircraft. Initial results show good agreement with measured noise transmitted into a rectangular box through a flat panel.

Mixson, J. S.↗

NASA NTRS1978

Development of flat-plate solar collectors for the heating and cooling of buildings: Executive summary

An efficient, low cost, flat-plate solar collector was developed. Computer aided mathematical models of the heat process in the collector were used in defining absorber panel configuration; determining insulation thickness; and in selecting the number, spacing, and material of the covers. Prototypes were built and performance tested. Data from simulated operation of the collector are compared with predicted loads from a number of locations to determine the degree of solar utilization.

Source record↗

NASA NTRS1978

Investigation of interior noise in a twin-engine light aircraft

This paper describes experimental studies of interior noise in a twin-engine, propeller-driven, light aircraft. An analytical model for this type of aircraft is also discussed. Results indicate that interior noise levels in this aircraft due to propeller noise can be reduced by reducing engine rpm at constant airspeed (about 3 dB), and by synchrophasing the twin engines/propellers (perhaps up to 12 dB). Ground tests show that the exterior noise pressure imposed on the fuselage consists of a complex combination of narrow-band harmonics due to propeller and engine exhaust sources. This noise is reduced by about 20-40 dB (depending on the frequency) by transmission through the sidewall to the cabin interior. The analytical model described uses modal methods and incorporates the flat-side geometrical and skin-stringer structural features of this light aircraft.

Mixson, J. S.↗

NASA NTRS1978

Pressure and velocity measurements in a three dimensional wall jet

A flat plate and a curved wall surface, intended to model a wing-flap combination in a high V/STOL configuration, were used to measure pressure and flow velocity in a freely expanding coflowing jet and a three dimensional wall jet. The effects of increasing the velocity ratio of the jet exit plane velocity to the free stream velocity were investigated. Velocity measurements were made using a two color laser Doppler velocimeter with a phase-locked loop processor. Fluctuating pressures were monitored with condenser-type microphones. Quantities measured include the width of the mixing region, the mean velocity field, turbulent intensities, and time scales. Wall and static pressure-velocity correlations and coherences are presented.

Catalano, G. D.↗

NASA NTRS1979

Application of a velocity-split Navier-Stokes solution technique to external flow problems

A method for solving the Navier-Stokes equations based on splitting the velocity vector into its rotational and irrotational parts has recently been applied successfully to internal flow computations. In this paper, the applicability of the method to external flows is examined by studying two model problems; laminar incompressible flow over semiinfinite and finite flat plates. For these problems the procedure accurately reproduces the known solutions and is computationally very efficient even at high Reynolds numbers. Computational aspects of the method are discussed along with the possibility of using the procedure to retrofit a viscous capability into existing transonic potential flow codes.

Dwoyer, D. L.↗

NASA NTRS1980

HEAO 1 spectra of X-ray emitting Seyfert 1 galaxies

The paper presents the 2-50-keV X-ray spectra and time variability information on seven Seyfert 1 galaxies NGC 3783, NGC 4151, NGC 5548, NGC 6814, MK 509, MCG 8-11-11, and ESO 141-G55, obtained with the A2(2) experiment on HEAO 1. It is concluded that the spectra of Seyfert 1 galaxies can be well represented by flat power laws of high-temperature thermal breamsstrahlung models with relatively low column densities.

Mushotzky, R. F.↗

NASA NTRS1980

Turbulent boundary layer heat transfer experiments: Convex curvature effects, including introduction and recovery

Heat transfer rates were measured through turbulent and transitional boundary layers on an isothermal, convexly curved wall and downstream flat plate. The effect of convex curvature on the fully turbulent boundary layer was a reduction of the local Stanton numbers 20-50% below those predicted for a flat wall under the same circumstances. The recovery of the heat transfer rates on the downstream flat wall was extremely slow. After 60 cm of recovery length, the Stanton number was still typically 15-20% below the flat wall predicted value. Various effects important in the modeling of curved flows were studied separately. These are: (1) the effect of initial boundary layer thickness; (2) the effect of freestream velocity; (3) the effect of freestream acceleration; (4) the effect of unheated starting length; and (5) the effect of the maturity of the boundary layer. Regardless of the initial state, curvature eventually forced the boundary layer into an asymptotic curved condition. The slope, minus one, is believed to be significant.

Simon, T. W.↗

NASA NTRS1982

Turbulent boundary layer heat transfer experiments: Convex curvature effects including introduction and recovery

Measurements were made of the heat transfer rate through turbulent and transitional boundary layers on an isothermal, convexly curved wall and downstream flat plate. The effect of convex curvature on the fully turbulent boundary layer was a reduction of the local Stanton numbers 20% to 50% below those predicted for a flat wall under the same circumstances. The recovery of the heat transfer rates on the downstream flat wall was extremely slow. After 60 cm of recovery length, the Stanton number was still typically 15% to 20% below the flat wall predicted value. Various effects important in the modeling of curved flows were studied separately. These are: the effect of initial boundary layer thickness, the effect of freestream velocity, the effect of freestream acceleration, the effect of unheated starting length, and the effect of the maturity of the boundary layer. An existing curvature prediction model was tested against this broad heat transfer data base to determine where it could appropriately be used for heat transfer predictions.

Simon, T. W.↗

NASA NTRS1983

Airfoil self noise - Effect of scale

Key data from a comprehensive airfoil broadband self-noise study are reported. Attention here is restricted to two-dimensional sharp trailing-edge models. The models include seven NACA 0012 airfoil sections and five 'flat plate' sections with chordlengths ranging from 2.54 to 60.96 cm. Testing parameters include flow velocity, angle of attack to the flow, and boundary layer turbulence through natural transition and through tripping. Detailed aerodynamic measurements, of pertinence to the scaling problem of airfoil self-noise, were conducted in the near-wake of the trailing edges. Presented are mean and rms turbulent velocity profiles as well as boundary layer thicknesses and integral thickness parameters for a large range of conditions. The noise spectra of the self-noise sources were determined by the use of a cross-spectral technique. The spectra were normalized using the measured aerodynamic parameters in order to evaluate the most common scaling law now in use. An examination of the Reynolds number dependence of the overall self-noise levels has revealed a new and useful scaling result. This result appears to quantify the transition between turbulent-boundary-layer trailing edge noise and laminar-boundary-layer vortex shedding noise.

Brooks, T. F.↗

NASA NTRS1984

The structure of evaporating and combusting sprays: Measurements and predictions

An apparatus developed, to allow observations of monodisperse sprays, consists of a methane-fueled turbulent jet diffusion flame with monodisperse methanol drops injected at the burner exit. Mean and fluctuating-phase velocities, drop sizes, drop-mass fluxes and mean-gas temperatures were measured. Initial drop diameters of 100 and 180 microns are being considered in order to vary drop penetration in the flow and effects of turbulent dispersion. Baseline tests of the burner flame with no drops present were also conducted. Calibration tests, needed to establish methods for predicting drop transport, involve drops supported in the post-flame region of a flat-flame burner operated at various mixture ratios. Spray models which are being evaluated include: (1) locally homogeneous flow (LFH) analysis, (2) deterministic separated flow (DSF) analysis and (3) stochastic separated flow (SSF) analysis.

Shuen, J. S.↗

NASA NTRS1985

Microdunes and Other Aeolian Bedforms on Venus: Wind Tunnel Simulations

The development of aeolian bedforms in the simulated Venusian environment has been experimentally studied in the Venus Wind tunnel. It is found that the development of specific bedforms, including ripples, dunes, and waves, as well as their geometry, are controlled by a combination of factors including particle size, wind speed, and atmospheric density. Microdunes are formed which are analogous to full-size terrestrial dunes and are characterized by the development of slip faces, internal cross-bedding, a low ratio of saltation path length to dune length, and a lack of particle-size sorting. They begin to develop at wind speeds just above saltation threshold and evolve into waves at higher velocities. At wind speeds of about 1.5 m/sec and higher, the bed is flat and featureless. This evolution is explained by a model based on the interaction of alternating zones of erosion and deposition and particle saltation distances.

Greeley, R.↗

NASA NTRS1984

Microdunes and other aeolian bedforms on Venus - Wind Tunnel simulations

The development of aeolian bedforms in the simulated Venusian environment has been experimentally studied in the Venus Wind Tunnel. It is found that the development of specific bedforms, including ripples, dunes, and 'waves', as well as their geometry, are controlled by a combination of factors including particle size, wind speed, and atmospheric density. Microdunes are formed which are analogous to full-size terrestrial dunes and are characterized by the development of slip faces, internal cross-bedding, a low ratio of saltation path length to dune length, and a lack of particle-size sorting. They begin to develop at wind speeds just above saltation threshold and evolve into waves at higher velocities. At wind speeds of about 1.5 m/sec and higher, the bed is flat and featureless. This evolution is explained by a model based on the interaction of alternating zones of erosion and deposition and particle saltation distances.

Greeley, R.↗

NASA NTRS1985

Scaling of airfoil self-noise using measured flow parameters

Data from an airfoil broadband self-noise study are reported. Attention here is restricted to two-dimensional models at zero angle of attack to the flow. The models include seven NACA 0012 airfoil sections and five flat plate sections with chordlengths ranging from 2.54 to 60.96 cm. Testing parameters include flow velocity to 71.3 m/s and boundary-layer turbulence through natural transition and by tripping. Detailed aerodynamic measurements are conducted in the near-wake of the sharp trailing edges. The noise spectra of the self-noise sources are determined by the use of a cross-spectral technique. The acoustic data are normalized using the measured aerodynamic parameters in order to evaluate a commonly used scaling law. An examination of the Reynolds number dependence of the normalized overall levels has revealed a useful scaling result. This result appears to quantify the transition between turbulent boundary-layer trailing-edge noise and laminar boundary-layer vortex shedding noise.

Brooks, T. F.↗

NASA NTRS1987

Tribology theory versus experiment

Tribology, the study of friction and wear of materials, has achieved a new interest because of the need for energy conservation. Fundamental understanding of this field is very complex and requires a knowledge of solid-state physics, material science, chemistry, and mechanical engineering. This paper is meant to be didactic in nature and outlines some of the considerations needed for a tribology research program. The approach is first to present a simple model, a field emission tip in contact with a flat surface, in order to elucidate important considerations, such as contact area, mechanical deformations, and interfacial bonding. Then examples from illustrative experiments are presented. Finally, the current status of physical theories concerning interfacial bonding are presented.

Ferrante, John↗

NASA NTRS1988

Axisymmetric confined turbulent jet directed towards the liquid surface from below

A numerical simulation is presented of an axisymmetric turbulent jet discharging axially from below into a cylindrical tank and directed towards the liquid vapor interface. The liquid vapor interface is assumed to be flat and shear free. The k-epsilon turbulence model is used to calculate the eddy viscosity. The turbulence intensity distribution and the length scale associated with the k-epsilon model are calculated as functions of jet flow rates and systems parameters. Numerical results are compared with appropriate experimental data. The problems associated with the free surface boundary conditions for the turbulent quantities are discussed.

Hasan, Mohammad M.↗

NASA NTRS1988

Observations of comets and asteroids

All available ground-based observational techniques are used to study the chemical and physical properties of the small bodies of the solar system, primarily comets and secondarily asteroids. The ultimate goal is to use these bodies to understand the formation and evolution of the solar system. The analysis of charge coupled device (CCD) images of comet P/Halley continued. This included a mojor revision of a paper on the periodicities of CN jets in Halley showing that their periodicity is 7.3 days, not 2.2 days. It also included an analysis of the continuum images which showed that the dust in jets is much redder than in the ambient coma. Calculations with Mie theory suggest that the particles that show the strongest effects of radiation pressure. Much effort was expended devising methods to estimate the level of sky background of the many images in which comet extends to the edge of the chip. Examined images of comet Wilson were taken over many months in 1987. Wilson, a dynamically new comet, shows none of the short-term variability or jet structure (either dusty jets or jets of radicals seen in Halley. This is presumably due to the lack of a mantle or the nucleus. Median-imaging of sky was as a technique for removing residual flat-fielding errors in CCD images. A Monte Carlo model and a convolution model were developed for studying temporal variability of gaseous daughter products.

Ahearn, Michael F.↗

NASA NTRS1988

Modeling of dynamic effects of a low power laser beam

Methods of modeling some of the dynamic effects involved in laser beam propagation through the atmosphere are addressed with emphasis on the development of simple but accurate models which are readily implemented in a physical optics code. A space relay system with a ground based laser facility is considered as an example. The modeling of such characteristic phenomena as laser output distribution, flat and curved mirrors, diffraction propagation, atmospheric effects (aberration and wind shear), adaptive mirrors, jitter, and time integration of power on target, is discussed.

Lawrence, George N.↗

NASA NTRS1989

Axisymmetric confined turbulent jet directed towards the liquid surface from below

Hasan, Mohammad M.↗