Search NASA⌕ Search

SEARCH · Search NASA

Results for “model structural error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Measurement of density and porosity of lunar rocks based on samples of Luna 16 automatic lunar station

Three fragments of holocrystalline igneous rocks of the gabbro type, weighing 30 to 50 mg each, were investigated. The density of the fragments was established with a mercury pycnometer and was found to be 3.05 to 3.12 g/cu cm, with a relative error not more than 2 percent. The porosity was found for the difference between the volumes determined with the mercury and with the gas techniques; for all three samples together it was 13 percent, and the error of determination was 70 percent owing to the small volumes. It can be anticipated that the porosity of the rock in bulk will be higher than the value obtained based on small fragments. The porosity of lunar rocks can markedly affect the isostatic distribution of rocks and must be taken into account when developing models of lunar structure.

Volynets, V. F.↗

Digital preprocessing of SEASAT imagery

A model for radar image data is derived for use in developing enhancement techniques. This model describes the image data as the result of a multiplicative-convolved noise process. This information is then used to design a minimum mean square error (MMSE) filter. The resulting filter is implemented adaptively to change with local statistics. A radar image processing technique which provides the MMSE estimate inside homogeneous areas and tends to preserve edge structure is thus developed. This technique has been implemented and tested using digitally correlated SEASAT-A synthetic aperture radar (SAR) imagery.

Frost, V. S.↗

Maneuvering of large flexible space antennas using optimal discrete-time controllers

The problem of maneuvering large space structures is formulated as a discrete-time, finite-duration optimal regulator problem. Two methods are considered for minimizing the elastic motion during the maneuver. The methods are applied to retargetting maneuver of a large space antenna, and the results are compared with those obtained using bang-bang control. The optimal regulator designed using the model error sensitivity supression method gives the best performance.

Joshi, S. M.↗

Sensor failure detection using generalized parity relations for flexible structures

Analytical redundancy may be preferable to hardware redundancy in failure detection/isolation tasks for such large-scale systems as space structures. Generalized single-sensor parity relations are presently applied to this problem; they are noted to yield a very simple isolation logic, and their generation is found to be extremely rapid, even in the case of extremely complex systems, provided only that the eigenstructure of the system be known. Their implementation is, however, extremely sensitive to modeling errors and noise.

Mercadal, Mathieu↗

Influence of structural and aerodynamic modeling on optimization with flutter constraint

The influences of structural and aerodynamic modeling on multidisciplinary optimization in an aeroelastic environment are not well understood. Therefore, optimizations with flutter and frequency constraints were performed to investigate the effects these modeling factors have on various representative wings. To this end, the Automated Structural Optimization System (ASTROS) was used as a tool to minimize the weight of various fully built-up finite element wing models in subsonic and supersonic flow under given flutter and frequency constraints. First, the performance of the optimization module was tested against results from other codes on a straight and uniform wing widely used for optimization with flutter constraints. Then, fully built-up finite element models of various wings with different aspect ratios were investigated for the influence on the structural optimization for minimum weight of the following modeling factors: finite element selection, structural grid refinement; number of selected modes, retention of breathing modes; selection of reduced frequencies to be used in flutter analysis; aerodynamic panel size and placement; splining of the aerodynamic grid to the structural grid selection of extra points of the structural wing box for splining; and number of constraints to be retained. Knowledge of these influences as well as of the program behavior is important, since optimization can be made more efficient by the selection of reasonable initial models. Also, it was shown previously that modeling has an impact on the results of modal and aeroelastic analyses. Thus, if modeling errors can negatively affect the analyses, a minimum weight optimization can be jeopardized and result in an optimal design that is rather unreliable. In the following, selected results are presented and the influences of some modeling parameters on optimization are pointed out.

Striz, Alfred G.↗

A Celestial Reference Frame Based on Kalman Filtering

In this study, we investigate a novel approach to the determination of celestial reference frames (CRF). Instead of a constant model for radio sources positions, we adopt a time series representation, which allows temporal variations of radio source coordinates to be taken into account. In particular, the added flexibility is beneficial for radio sources with extended structure. We compute our time series-based CRF solutions by Kalman filtering and smoothing radio source positions, which are initially obtained from single-session VLBI analysis. The temporal resolution of the estimated CRF coordinates is identical to that of the input data, i.e. usually 1-4 days. The magnitude of the coordinate variations is controlled by the amount of process noise applied in the filter, which is in turn derived from analyzing the Allan standard deviation of the corresponding radio source coordinate time series. Measures have been developed to reduce the impact of observation errors and datum effects on the noise model.

Soja, B.↗

An Evaluation of Current NASTRAN Discrete Element Models for Monocoque and Semimonocoque Structures

The current discrete element analysis models in NASTRAN, Levels 8. 1.0 and 11. 1. 0, are evaluated for semi-rnonocoque and monocoque structures. Comparative results are presented with the FORMAT-I11 general-purpose code for a swept wing statics analysis and a Skylab substructure vibration analysis. Good agreement between Level i I. 1.0 and FORMAT-111 is demonstrated; however, a major error in Level 8. 1.0 was discovered on the Skylab vibration problem. The computational performance of NASTRAN was superior to FORMAT, but the vibration rigid format was found to have several inefficiencies. Comparative results are also presented between Level 11. 1. 0 and STACUSS, SLADE, BOND, UNIVALVE, and another special-purpose code. Results for two of the structures analyzed, a cylindrical shell and an elliptic plate, indicate curved discrete elements are significantly more accurate than the plate elements in NASTRAN for the same number of degrees of freedom.

Edward L. Stanton↗

AAA gunnermodel based on observer theory

The Luenberger observer theory is used to develop a predictive model of a gunner's tracking response in antiaircraft artillery systems. This model is composed of an observer, a feedback controller and a remnant element. An important feature of the model is that the structure is simple, hence a computer simulation requires only a short execution time. A parameter identification program based on the least squares curve fitting method and the Gauss Newton gradient algorithm is developed to determine the parameter values of the gunner model. Thus, a systematic procedure exists for identifying model parameters for a given antiaircraft tracking task. Model predictions of tracking errors are compared with human tracking data obtained from manned simulation experiments. Model predictions are in excellent agreement with the empirical data for several flyby and maneuvering target trajectories.

Kou, R. S.↗

A relational approach to the development of expert diagnostic systems

The proposition that, given a structural and/or functional description of any real or abstract system, an expert system can be built based on this description is examined. First, a model is developed for a microprocessor-controlled end effector/sensor system using a modeling approach called a relational Knowledge-Base Machine (RKBM). Next, an explanation of how the end effector model could be used for the error diagnosis on the operational end effector is given and two versions of an error diagnosis algorithm based on the model are presented. Finally, areas of further research are described that are necessary before an expert system using this approach becomes a reality.

Ames, K. R.↗

Variable structure control of globally feedback-decoupled deformable vehicle maneuvers

The use of Cayley-Rodrigues attitude parameters as kinematic variables is shown to yield a globally linearized and decoupled model of the equations of motion of a deformable body, where the structural deformation state appears only in the coefficients of the inverse transformation. It is shown how commanded multiaxial attitude maneuvers can be encoded as switching surfaces for a variable-structure control implementation of the corresponding computed slew torques, automatically modulated in respnse only to detected angular rate error signs, for accurate tracking in the presence of separately damped or even uncontrolled (but stable) structural deformations.

Dwyer, T. A. W., III↗

Evaluation of the Lattice-Boltzmann Equation Solver PowerFLOW for Aerodynamic Applications

A careful comparison of the performance of a commercially available Lattice-Boltzmann Equation solver (Power-FLOW) was made with a conventional, block-structured computational fluid-dynamics code (CFL3D) for the flow over a two-dimensional NACA-0012 airfoil. The results suggest that the version of PowerFLOW used in the investigation produced solutions with large errors in the computed flow field; these errors are attributed to inadequate resolution of the boundary layer for reasons related to grid resolution and primitive turbulence modeling. The requirement of square grid cells in the PowerFLOW calculations limited the number of points that could be used to span the boundary layer on the wing and still keep the computation size small enough to fit on the available computers. Although not discussed in detail, disappointing results were also obtained with PowerFLOW for a cavity flow and for the flow around a generic helicopter configuration.

Lockard, David P.↗

Modeling the Proton Radiation Belt With Van Allen Probes Relativistic Electron-Proton Telescope Data

An empirical model of the proton radiation belt is constructed from data taken during 2013-2017 by the Relativistic Electron-Proton Telescopes on the Van Allen Probes satellites. The model intensity is a function of time, kinetic energy in the range 18-600 megaelectronvolts, equatorial pitch angle, and L shell of proton guiding centers. Data are selected, on the basis of energy deposits in each of the nine silicon detectors, to reduce background caused by hard proton energy spectra at low L. Instrument response functions are computed by Monte Carlo integration, using simulated proton paths through a simplified structural model, to account for energy loss in shielding material for protons outside the nominal field of view. Overlap of energy channels, their wide angular response, and changing satellite orientation require the model dependencies on all three independent variables be determined simultaneously. This is done by least squares minimization with a customized steepest descent algorithm. Model uncertainty accounts for statistical data error and systematic error in the simulated instrument response. A proton energy spectrum is also computed from data taken during the 8 January 2014 solar event, to illustrate methods for the simpler case of an isotropic and homogeneous model distribution. Radiation belt and solar proton results are compared to intensities computed with a simplified, on-axis response that can provide a good approximation under limited circumstances.

Selesnick, R. S.↗

A probabilistic fracture mechanics approach for structural reliability assessment of space flight systems

A probabilistic fracture mechanics approach for predicting the failure life distribution due to subcritical crack growth is presented. A state-of-the-art crack propagation method is used in a Monte Carlo simulation to generate a distribution of failure lives. The crack growth failure model expresses failure life as a function of stochastic parameters including environment, loads, material properties, geometry, and model specification errors. A stochastic crack growth rate model that considers the uncertainties due to scatter in the data and mode misspecification is proposed. The rationale for choosing a particular type of probability distribution for each stochastic input parameter and for specifying the distribution parameters is presented. The approach is demonstrated through a probabilistic crack growth failure analysis of a welded tube in the Space Shuttle Main Engine. A discussion of the results from this application of the methodology is given.

Sutharshana, S.↗

Confidence set inference with a prior quadratic bound

In the uniqueness part of a geophysical inverse problem, the observer wants to predict all likely values of P unknown numerical properties z=(z sub 1,...,z sub p) of the earth from measurement of D other numerical properties y (sup 0) = (y (sub 1) (sup 0), ..., y (sub D (sup 0)), using full or partial knowledge of the statistical distribution of the random errors in y (sup 0). The data space Y containing y(sup 0) is D-dimensional, so when the model space X is infinite-dimensional the linear uniqueness problem usually is insoluble without prior information about the correct earth model x. If that information is a quadratic bound on x, Bayesian inference (BI) and stochastic inversion (SI) inject spurious structure into x, implied by neither the data nor the quadratic bound. Confidence set inference (CSI) provides an alternative inversion technique free of this objection. Confidence set inference is illustrated in the problem of estimating the geomagnetic field B at the core-mantle boundary (CMB) from components of B measured on or above the earth's surface.

Backus, George E.↗

Verification of a SEU model for advanced 1-micron CMOS structures using heavy ions

Modeling and test results are reported for 1 micron CMOS circuits. Analytical predictions are correlated with experimental data, and sensitivities to process and design variations are discussed. Unique features involved in predicting the SEU performance of these devices are described. The results show that the critical charge for upset exhibits a strong dependence on pulse width for very fast devices, and upset predictions must factor in the pulse shape. Acceptable SEU error rates can be achieved for a 1 micron bulk CMOS process. A thin retrograde well provides complete SEU immunity for N channel hits at normal incidence angle. Source interconnect resistance can be important parameter in determining upset rates, and Cf-252 testing can be a valuable tool for cost-effective SEU testing.

Cable, J. S.↗

Optics Program Simplifies Analysis and Design

Engineers at Goddard Space Flight Center partnered with software experts at Mide Technology Corporation, of Medford, Massachusetts, through a Small Business Innovation Research (SBIR) contract to design the Disturbance-Optics-Controls-Structures (DOCS) Toolbox, a software suite for performing integrated modeling for multidisciplinary analysis and design. The DOCS Toolbox integrates various discipline models into a coupled process math model that can then predict system performance as a function of subsystem design parameters. The system can be optimized for performance; design parameters can be traded; parameter uncertainties can be propagated through the math model to develop error bounds on system predictions; and the model can be updated, based on component, subsystem, or system level data. The Toolbox also allows the definition of process parameters as explicit functions of the coupled model and includes a number of functions that analyze the coupled system model and provide for redesign. The product is being sold commercially by Nightsky Systems Inc., of Raleigh, North Carolina, a spinoff company that was formed by Mide specifically to market the DOCS Toolbox. Commercial applications include use by any contractors developing large space-based optical systems, including Lockheed Martin Corporation, The Boeing Company, and Northrup Grumman Corporation, as well as companies providing technical audit services, like General Dynamics Corporation

Source record↗

Wide Field Infrared Survey Telescope (WFIRST) Observatory Overview

NASA's Wide Field Infrared Survey Telescope (WFIRST) is being designed to deliver unprecedented capability in dark energy and exoplanet science, and to host a technology demonstration coronagraph for exoplanet imaging and spectroscopy. The observatory design has matured since 2013; we present a comprehensive description of the observatory configuration as refined during the WFIRST Phase-A study. The observatory is based on an existing, repurposed 2.4 meter space telescope coupled with a 288 megapixel near-infrared (0.6 to 2 microns) HgCdTe focal plane array with multiple imaging and spectrographic modes. Together they deliver a 0.28 square degree field of view, which is approximately 100 times larger than the Hubble Space Telescope, and a sensitivity that enables rapid science surveys. In addition, the coronagraph technology demonstration will prove the feasibility of new techniques for exoplanet discovery, imaging, and spectral analysis. A composite truss structure meters both instruments to the telescope assembly, and the instruments and the spacecraft are flight serviceable. We present configuration changes since 2013 that improved interfaces, improved testability, and reduced technical risk. We provide an overview of our Integrated Modeling results, performed at an unprecedented level for a phase-A study, to illustrate performance margins with respect to static wavefront error, jitter, and thermal drift.

Casey, T.↗

Static Aeroelastic Modeling of a Sub-Scale Wind Tunnel Model with Novel Flap Concept

This paper examines the static aeroelastic modeling of a flexible wind tunnel model equipped with a novel control effector known as the Variable Camber Continuous Trailing Edge Flap (VCCTEF) system. The wind tunnel model is an approximately 10 percent sub-scale version of a wing designed to be equipped on a commerical transport aircraft such as the full-scale NASA Generic Transport Model (GTM). The structure of the model is made highly flexible such that a 10 percent of semi-span wing tip deflection is expected at a design lift condition, and a representation of the VCCTEF concept is incorporated on the model. Static aeroelastic modeling is conducted by using a representative single beam structural finite-element model coupled to a vortex-lattice aerodynamic model. The resulting aeroelastic model of the flexible wind tunnel model is compared against experimental wind tunnel test results from the actual model tested at the University of Washington Aeronautical Laboratory (UWAL). Comparison cases are made using reference and VICON measurements of VCCTEF flap deflections from the wind tunnel test data, and percent errors between the lift curve parameters are presented. The results show up to a maximum percent of error of <10% with regards to lift curve slope values between the aeroelastic model and the UWAL test data. The agreement of lift curve slope values from the aeroelastic model and experimental test results serves as validation for the coupled vortex-lattice finite-element static aeroelastic model.

Aeroelasticity↗