Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase conversion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Innovating Distributed Embedded Energy Prize (InDEEP): A Lessons Learned Report

The U.S. Department of Energy's Water Power Technologies Office (WPTO) launched the Innovating Distributed Embedded Energy Prize (InDEEP) in March 2023 to accelerate innovation in Distributed Embedded Energy Conversion Technologies (DEEC-Tec) for ocean wave energy. Administered by the National Laboratory of the Rockies (NLR) with technical support from Sandia National Laboratories (SNL), InDEEP focused on the development of small, distributed, and embeddable energy converters (DEECs) and their integration into scalable DEEC-Tec metamaterials for marine renewable energy applications. Spanning three phases over two years, InDEEP awarded approximately $2.3 million to teams from academia, industry, and startups. Phase I emphasized conceptual design. Phase II moved into the prototyping of individual DEECs. Phase III required integration into functional DEEC-Tec metamaterial prototypes. Across 60 submissions, teams explored a wide range of energy conversion mechanisms - including piezoelectric, variable-capacitance, ionic, and inductive methods. Note, the prize did not include the design nor demonstration of ocean wave energy conversion systems. Rather, the prize only required participants to design and demonstrate individual DEECs and corresponding DEEC-Tec metamaterials. This prize utilized a mix of novel and proven techniques to attract participants from outside marine energy, including an engagement leaderboard, robust recruitment, technical expert mentorship, and a suite of technical trainings. Key insights from the competition emphasized that DEEC-Tec metamaterials must be intentionally designed to produce beneficial emergent behaviors - advantages that go beyond simply combining multiple DEEC units. Top-performing teams showed that thoughtful design of system architecture, coordinated deformation, and systems adaptabilities could unlock meaningful performance gains both at the DEEC system level and DEEC-Tec metamaterial system level. A critical realization was that many DEEC-Tec metamaterials could benefit from being designed to accept lower-frequency energy inputs and shift those into higher-frequencies per each DEEC making up the respective DEEC-Tec metamaterial. Other important takeaways included the need for rigorous and quantitative performance testing, effective integration of power conditioning electronics, and the pivotal role of material science in enabling innovative, adaptive DEEC-Tec-based energy conversion designs. InDEEP also helped establish a growing DEEC-Tec community of practitioners, attracting participants from beyond traditional marine energy sectors. Through a strong support infrastructure, InDEEP fostered early-stage innovation and laid a foundation for future DEEC-Tec-based ocean wave energy conversion solutions - positioning DEEC-Tec as a promising pathway toward scalable, resilient ocean wave energy conversion. Through focused R&D of individual DEECs and their integration into DEEC-Tec metamaterials, alongside a growing, multidisciplinary community catalyzed by InDEEP, there is a strong opportunity to drive a disruptive shift in ocean wave energy conversion design and development. This convergence of novel architectures, emergent behaviors, and collaborative innovation positions DEEC-Tec as a transformative approach, moving the field from rigid, centralized energy conversion-based designs to resilient, modular systems highly adaptable for real-world ocean wave energy conversion applications.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Optimizing hierarchical membrane/catalyst systems for oxidative coupling of methane using additive manufacturing

The advantage of a membrane/catalyst system in oxidative coupling of methane (OCM) compared to conventional reactive systems is that by introducing oxygen to the OCM catalytic sites through a membrane, parasitic gas phase reactions of O 2 (g), responsible for lowering product selectivity, can be avoided. The design and fabrication of membrane/catalyst systems has, however, been hampered by low volumetric chemical conversion rates, high capital cost, and difficulties in codesigning membrane and catalyst properties to optimize the performance. We solve these issues by developing a dual-layer additive manufacturing process, based on phase inversion, to design, fabricate and optimize a hollow fiber membrane/catalyst system for OCM. We demonstrate the approach though a case study using BaCe 0.8 Gd 0.2 O 3-δ (BCG) as the basis of both the catalyst and separation layers. We show that by using the manufacturing approach we can codesign the membrane thickness and catalyst surface area so that the flux of oxygen transport through the membrane and methane activation rates in the catalyst layer match each other. Here, we demonstrate that this “rate matching” is critical for maximizing the performance, with the membrane/catalyst system significantly overperforming conventional reactor designs under identical conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Designing an Intrusion Detection for an Adjustable Speed Drive System Controlling a Critical Process

In this article, we address the cyber-security problem of industrial control systems (ICSs) when their sensor measurements may be compromised due to an attacker who has intercepted those measurements via a network. We introduce a general-purpose method “Dynamic Watermarking (DW)” to detect potential cyber-intrusions on speed sensor measurements within industrial control systems, which deploy an adjustable speed drive (ASD) to control a critical process. The DW method is injecting a random private low-amplitude signal with a zero mean Gaussian distribution, “watermark”, into one of the input phase voltages powering the ASD system. The watermark signal propagates through the system including pulse width modulation (PWM) power conversion stage and motor, then ultimately appears in the speed sensor measurements. By deploying two statistical DW tests with two proper thresholds, the system can detect potential cyber-intrusions or unobservable cyber-attacks such as replay attacks and false data injection attacks (FDIA). The DW method tested on a laboratory-scale ASD system experimentally to protect the system against cyber-intrusions. This system, powered by a commercial PWM drive operating at 208 V, 3-phase, and 3.7 kW, served as our experimental platform.

42 ENGINEERING↗
DOE OSTI2022

Extracting energy from ocean thermal and salinity gradients to power unmanned underwater vehicles: State of the art, current limitations, and future outlook

Thermal gradient energy-generation technologies for powering unmanned underwater vehicles (UUVs) or autonomous sensing systems in the ocean are mainly in the research development phase or commercially available at a limited scale, and salinity-gradient energy-generation technologies have not been adequately researched yet. The demand for self-powered UUVs suitable for long-term deployments has been growing, and further research related to small-scale ocean gradient energy systems is needed. In this study, we conducted a comprehensive review about harvesting energy from ocean thermal or salinity gradients for powering UUVs, focusing on gliders and profiling floats. Thermal gradient energy systems for UUVs based on phase change materials (PCM) cannot provide the energy required for powering autonomous sensing systems because of the systems' low energy conversion efficiency. Besides reducing energy consumption by developing more efficient electrical-mechanical systems, enhancing the thermal conductivity of the PCMs may help address this challenge by increasing the power generation rate of the UUVs. Several other emerging technologies, such as thermoelectric generators, shape memory alloys, and small-scale thermodynamic cycle systems, have shown potential for powering UUVs, but they are still only at the laboratory testing or conceptual design phase. The most advanced power generation technologies based on salinity gradients, reverse electrodialysis and pressure-retarded osmosis, are still not economically viable for large-scale deployment, mainly because of the high cost of the components required to operate in harsh saline environments. Our feasibility evaluation showed that existing salinity gradient power generation technologies are not directly feasible for powering UUVs in the open ocean.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Conversion of METL Diagnostic Flowmeters to Permanent Magnet Based Electromagnetic Flowmeters

The Mechanisms Engineering Test Loop (METL) uses three flowmeters to monitor sodium circulation through the main loop, the Cold Trap leg, and the Plugging Meter leg. When constructed, the Cold Trap flowmeter (CTFM) and Plugging Meter flowmeter (PMFM) were equipped with permanent magnets and Hall Sensors. By October of 2019, during normal operations, both the CTFM and PMFM failed, producing either erroneous or zero signals. Repairs to the flowmeters were attempted in January of 2020 but failed to resolve the issues. Therefore, starting in March of 2021, a plan was developed to convert the installed flowmeters to more robust permanent magnet based electromagnetic flowmeters (EMFMs). The Cold Trap EMFM (CT EMFM) and Plugging Meter EMFM (PM EMFM) were fully installed by August of 2021. Initial testing and commissioning were completed in November of 2021. Finally, the first calibration runs were finished in March of 2022. This report discusses the design, conversion, and calibration of the as-built CTFM and PMFM to robust permanent magnet based EMFMs. During the design phase, theoretical models were used to estimate the signal output and required magnet sizes. Then, the CTFM and PMFM were disassembled and converted to EMFMs. After commissioning, the CT EMFM and PM EMFM were calibrated using a ‘Time Transfer Procedure’ carried out with METL Expansion Vessels and Test Vessel Two. The accuracy of the calibration was estimated through an uncertainty analysis. Finally, the report describes some lessons learned for future flowmeter conversions and follow-up work. In total, both METL EMFM’s met the desired performance targets. Testing data showed that the METL EMFMs provide a output signal of roughly 2 mV at 1 GPM and 250 °C. During calibration, flowrates between 0.7 GPM and 2.4 GPM were achieved. In this flow range, calibration coefficients of 0.485 and 0.935 were measured as with errors ranging from 15-5% and 16-5% for the CT EMFM and PM EMFM, respectively. Above 1.5 GPM, the error was assumed to be about 5% for both METL EMFMs. Several points will be considered for future follow-up work on the METL EMFM’s. First, the signal noise issues in the PM EMFM will be addressed. It is likely the source of the noise is due to some stray EMF from a heater. Secondly, the NdFeB magnets will be replaced with a grade that has a Curie temperature above 80 °C. For example, a few grades of NeFeB magnets have Curie temperatures which exceed 150 °C and some SmCo magnets have Curie temperatures as high as 500 °C. Third, more calibration runs will be completed in the range of 0.5-2.5 GPM. This will further improve the accuracy of the calibration coefficient. Fourth, calibration runs will be completed up to 5 GPM. This requires a larger pressure relief valve to be installed on the Expansion Vessel and Test Vessel 2, as well as a revised calibration procedure. Lastly, calibration runs will be completed to account for cold spots in the system, which reduced the inlet temperature of the METL EMFMs. Overall, these points will improve the calibration coefficients derived in this work and also improve the performance of the METL EMFMs.

42 ENGINEERING↗
DOE OSTI2020

Viscosity of glass-forming melt at the bottom of high-level waste melter feed cold caps: Effects of temperature and incorporation of solid components

At the final stages of conversion of melter feed (glass batch) to molten glass, the transient glass-forming melt becomes a continuous liquid phase encapsulating dissolving solid particles and gas bubbles that produce primary foam at the bottom of the cold cap (the reacting melter feed in an electric glass melting furnace). The glass-forming melt viscosity plays a dominant role in primary foam formation, stability, and eventual collapse, thus affecting the rate of melting (the glass production rate per cold cap area). For several melter feeds designed for nuclear waste vitrification, we have traced the glass-forming melt viscosity during the final stages of feed-to-glass conversion as it changes in response to changing temperature and composition (resulting from dissolving solid particles). Starting with a relatively low values at the moment when the melt connects, melt viscosity reaches maximum within the primary foam layer and then decreases to its final melter-operating temperature value. We paid a particular attention to the cold-cap bottom—the boundary between the primary foam layer and the thermal boundary layer—where the melt viscosity affects the rate of melting predominantly through its effect on the temperature at which primary foam is collapsing.

Lee, Seung Min↗
DOE OSTI2025

Additive manufacturing of carbon fiber-reinforced thermoset composites via in-situ thermal curing

Fiber-reinforced polymer composites are lightweight structural materials widely used in the transportation and energy industries. Current approaches for the manufacture of composites require expensive tooling and long, energy-intensive processing, resulting in a high cost of manufacturing, limited design complexity, and low fabrication rates. Here, we report rapid, scalable, and energy-efficient additive manufacturing of fiber-reinforced thermoset composites, while eliminating the need for tooling or molds. Use of a thermoresponsive thermoset resin as the matrix of composites and localized, remote heating of carbon fiber reinforcements via photothermal conversion enables rapid, in-situ curing of composites without further post-processing. Rapid curing and phase transformation of the matrix thermoset, from a liquid or viscous resin to a rigid polymer, immediately upon deposition by a robotic platform, allows for the high-fidelity, freeform manufacturing of discontinuous and continuous fiber-reinforced composites without using sacrificial support materials. This method is applicable to a variety of industries and will enable rapid and scalable manufacture of composite parts and tooling as well as on-demand repair of composite structures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Co-synthesis of Hydrogen and High-Value Carbon Products from Methane Pyrolysis

The ARPA-E Methane Pyrolysis Project successfully developed a scalable technology for hydrogen production with low-CO x emission through methane pyrolysis, co-producing high-value carbon nanotubes (CNTs). The project focused on optimizing reactor design, enhancing catalyst performance, and assessing techno-economic feasibility to create a commercially viable and environmentally sustainable process. The fluidized bed reactor achieved over 90% methane (CH 4 ) conversion by using a 5% CO 2 co-feed, which stabilizes carbon yields and minimizes catalyst deactivation. This setup allowed for continuous operation across ten cycles, each consisting of a 14-minute pyrolysis phase followed by a 10-minute dislodging phase to remove a fraction of the accumulated carbon, resulting in stable performance and high-quality CNT production. In parallel, monolith reactors coated with Fe demonstrated a sustained methane conversion of 73% while producing CNTs with high crystallinity. Although promising for continuous operation, monolith reactors face challenges in coating durability and scalability, highlighting areas for further optimization in commercial applications. Catalyst formulation played a key role in enhancing process efficiency. The core catalyst used was 5%Fe/Al 2 O 3 (wt%), optimized through wet impregnation, which improved CNT morphology, yielding longer and more uniform CNTs. The catalyst's performance was further enhanced by adding promoters: 2.5 wt% Ni increased methane conversion close to the thermodynamic limit, while 2.5 wt% Mn improved CNT alignment and crystallinity, and 1.5 wt% NaCl boosted CNT morphology but slightly lowered methane conversion. These adjustments allowed the reactor to maintain high methane conversion while producing high-quality CNTs, enabling stable performance over multiple cycles. To address carbon buildup and ensure uninterrupted operation, a pneumatic conveying tube was implemented for effective carbon dislodging in the fluidized bed configuration. CO 2 and H 2 O co-feeds were also introduced to enhance carbon removal, with CO 2 boosting CNT yield by approximately 15%. This setup enabled stable reactor operation across multiple cycles, preventing clogging and minimizing catalyst wear, making the process suitable for industrial scaling. Techno-economic analysis (TEA) projected hydrogen production costs between $\$$1.00 and $\$$1.64 per kilogram, with CNT values assumed at $\$$375/ton and $\$$100/ton. The life cycle assessment showed that CO 2 emissions could be as low as 0.64 kg CO 2 e/kg H 2 at 95% methane conversion assuming an electricity input of 50 kg CO 2 e/MWh. Even at 50% methane conversion, emissions remained below 1 kg CO 2 e/kg H 2 , demonstrating the process's low-emission potential and making it a viable alternative to traditional steam methane reforming. Overall, the results from this project demonstrate the feasibility of a pyrolysis process where carbon is continuously removed from the catalyst surface and hydrogen is continuously produced until a catalyst regeneration step is required to fully clean the catalyst surface and renew catalyst performance. Major open challenges are related to avoiding the loss of catalyst material in the dislodged carbon during fluidized bed conditions, since our best result demonstrated a carbon purity of ~70 wt. % (rest being iron and alumina). A monolith reactor was used to favor dislodgement of carbon compared to fluidized bed conditions but our results do not demonstrate an advantage of the monolith configuration. Catalyst performance was similar to fluidized bed conditions with slower deactivation rates overall, but we could not observe carbon dislodging in any of the tens of experiments that were run at Stanford. Our results show that the most relevant areas of improvement are related to the fundamental understanding of the iron-carbon interface for dislodging, and the development of catalyst that can produce CNTs via a base-growth mechanism such that catalyst is not lost in the dislodgement steps. The final report documents all findings and methodologies in detail, providing a valuable resource for the scientific community. By building on these results, researchers can further advance methane pyrolysis technology, moving toward a more sustainable, scalable pathway for hydrogen production. This work lays the foundation for future research and commercial efforts to reduce emissions in hydrogen production while generating valuable carbon products.

08 HYDROGEN↗
DOE OSTI2025

Confocal Raman Microscopy for Measuring In Situ Temperature-Dependent Structural Changes in Poly(Ethylene Oxide) Thin Films

Crystallization from the melt is a critical process governing the properties of semi-crystalline polymeric materials. While structural analyses of melting and crystallization transitions in bulk polymers have been widely reported, in contrast, those in thin polymer films on solid supports have been underexplored. Herein, in situ Raman microscopy and self-modeling curve resolution (SMCR) analysis are applied to investigate the temperature-dependent structural changes in poly(ethylene oxide) (PEO) films during melting and crystallization phase transitions. By resolving complex overlapping sets of spectra, SMCR analysis reveals that the thermal transitions of 50 µm thick PEO films comprise two structural phases: an ordered crystalline phase and a disordered amorphous phase. The ordered structure of the crystalline PEO film entirely disappears as the polymer is heated; conversely, the disordered structure of the amorphous PEO film reverts to the ordered structure as the polymer is cooled. Broadening of the Raman bands was observed in PEO films above the melting temperature (67 °C), while sharpening of bands was observed below the crystallization temperature (45 °C). The temperatures at which these spectral changes occurred were in good agreement with differential scanning calorimetry (DSC) measurements, especially during the melting transition. The results illustrate that in situ Raman microscopy coupled with SMCR analysis is a powerful approach for unraveling complex structural changes in thin polymer films during melting and crystallization processes. Furthermore, we show that confocal Raman microscopy opens opportunities to apply the methodology to interrogate the structural features of PEO or other surface-supported polymer films as thin as 2 µm, a thickness regime beyond the reach of conventional thermal analysis techniques.

Koh, Miharu [Department of Chemistry, University o↗
NASA NTRS1984

A numerical analysis of transient planetary waves and the vertical structure in a meso-strato-troposphere model, part 1.4A

The structure of unstable planetary waves is computed by a quasi-geostrophic model extending from the surface up to 80 km by means of eigenvalue-eigenfunction techniques in spherical coordinates. Three kinds of unstable modes of distinct phase speeds and vertical structures are identified in the winter climate state: (1) the deep Green mode with its maximum amplitude in the stratosphere; (2) the deep Charney mode with its maximum amplitude in the troposphere: and (3) the shallow Charney mode which is largely confined to the troposphere. Both the Green mode and the deep Charney mode are characterized by very slow phase speeds. They are mainly supported by upward wave energy fluxes, but the local baroclinic energy conversion within the stratosphere also contributes in supporting these deep modes. The mesosphere and the troposphere are dynamically independent in the summer season decoupled by the deep stratospheric easterly. The summer mesosphere supports the easterly unstable waves 1-4. Waves 3 and 4 are identified with the observed mesospheric 2-day wave and 1.7-day wave, respectively.

Zhang, K. S.↗
NASA NTRS1985

Polycyclic aromatic hydrocarbons and the diffuse interstellar bands

This paper discusses some of the thermodynamic and spectroscopic properties of polycyclic aromatic hydrocarbons which make them attractive candidates as carriers of the Diffuse Interstellar Bands (DIBs). It is pointed out that, in the diffuse medium, many of these species will be partially hydrogenated and positively charged, and will absorb in the visible. The observed lineshapes and widths of the DIBs can be explained by rovibronic band contours and linebroadening due to internal conversion. Since little information is available concerning the spectroscopic properties of such species in the gas phase, a considerable amount of laboratory and theoretical work is needed.

Van Der Zwet, G. P.↗
NASA NTRS1990

High-frequency ac power distribution in Space Station

A utility-type 20-kHz ac power distribution system for the Space Station, employing resonant power-conversion techniques, is presented. The system converts raw dc voltage from photovoltaic cells or three-phase LF ac voltage from a solar dynamic generator into a regulated 20-kHz ac voltage for distribution among various loads. The results of EASY5 computer simulations of the local and global performance show that the system has fast response and good transient behavior. The ac bus voltage is effectively regulated using the phase-control scheme, which is demonstrated with both line and load variations. The feasibility of paralleling the driver-module outputs is illustrated with the driver modules synchronized and sharing a common feedback loop. An HF sinusoidal ac voltage is generated in the three-phase ac input case, when the driver modules are phased 120 deg away from one another and their outputs are connected in series.

Tsai, Fu-Sheng↗
NASA NTRS2015

High Temperature Joining and Characterization of Joint Properties in Silicon Carbide-Based Composite Materials

Advanced silicon carbide-based ceramics and composites are being developed for a wide variety of high temperature extreme environment applications. Robust high temperature joining and integration technologies are enabling for the fabrication and manufacturing of large and complex shaped components. The development of a new joining approach called SET (Single-step Elevated Temperature) joining will be described along with the overview of previously developed joining approaches including high temperature brazing, ARCJoinT (Affordable, Robust Ceramic Joining Technology), diffusion bonding, and REABOND (Refractory Eutectic Assisted Bonding). Unlike other approaches, SET joining does not have any lower temperature phases and will therefore have a use temperature above 1315C. Optimization of the composition for full conversion to silicon carbide will be discussed. The goal is to find a composition with no remaining carbon or free silicon. Green tape interlayers were developed for joining. Microstructural analysis and preliminary mechanical tests of the joints will be presented.

Joining↗
NASA NTRS2017

Unusual Oxidative Limitations for Al-MAX Phases

Alumina-forming MAX phases are well-known for their excellent oxidation resistance, rivaling many metallic NiAl, NiCrAl, and FeCrAl counterparts and with upper temperature capability possible to approximately1400C. However a number of limitations have been emerging that need to be acknowledged to permit robust performance in demanding applications. Ti2AlC and Ti3AlC2 possess excellent scale adhesion, cyclic oxidation/moisture/volatility resistance, and TBC compatibility. However they are very sensitive to Al content and flux in order to maintain an exclusive Al2O3 scale without runaway oxidation of ubiquitous TiO2 transient scales. Accelerated oxidation has been shown to occur for Al-depleted, damaged, or roughened surfaces at temperatures less than 1200C. Conversely, Cr2AlC is less sensitive to transients, but exhibits volatile losses at 1200C or above if common Cr7C3 impurity phases are present. Poor scale adhesion is exhibited after oxidation at 1150C or above, where spallation occurs at the Cr7C3 (depletion zone) interface. Delayed spallation is significant and suggests a moisture-induced phenomenon similar to non-adherent metallic systems. Re-oxidation of this surface does not reproduce the initial pure Al2O3 behavior, but initiates a less-protective scale. Cr2AlC has also been shown to have good long term bonding with superalloys at 800C, but exhibits significant Beta-NiAl + Cr7C3 diffusion zones at 1100C and above. This may set limits on Cr2AlC as a high temperature TBC bond coat on Ni-based superalloys, while improving corrosion resistance in lower temperature applications.

oxidation resistance↗
DOE OSTI2025

Evaporator Temperature Transient Testing of a High-Performance Sodium Filled Heat Pipe

Heat pipes are two-phase heat transfer devices that enable passive removal of heat from the reactor core to the power conversion system in heat pipe-cooled microreactor designs. Experimental investigations of heat pipe transients are needed for technology demonstration, verification and validation of numerical codes, and the establishment of regulatory requirements. The Single Primary Heat Extraction and Removal Emulator (SPHERE) facility at Idaho National Laboratory (INL) serves as a platform for evaluating the dynamic response of high-temperature heat pipes under a variety of operating conditions. The present work details the experimental investigation of a high-performance, defined as over 2 kW sodium heat pipe subjected to rapid input power fluctuations induced by sudden changes in the evaporator temperature setpoint. In addition, the heat pipe was subjected to an asymmetrical heat load where a subset of heaters operated at 30% and 70% below their nominal power. These experimental conditions were chosen to simulate thermal and operational stresses expected to be encountered in microreactors to provide data on heat pipe behavior during such important transient events. Key data and performance metrics, including time series of temperatures and strains, axial temperature profiles, thermal response times, and heat transfer capabilities, the thermal output over thermal input, were reported and discussed. The results highlight the resilience of heat pipes, revealing their potential to maintain thermal stability and efficiency under varying power loads. Lastly, the paper concludes with a discussion on the significance of the results and their implications for future research.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1983

Harnessing surface plasmons for solar energy conversion

NASA research on the feasibility of solar-energy conversion using surface plasmons is reviewed, with a focus on inelastic-tunnel-diode techniques for power extraction. The need for more efficient solar converters for planned space missions is indicated, and it is shown that a device with 50-percent efficiency could cost up to 40 times as much per sq cm as current Si cells and still be competitive. The parallel-processing approach using broadband carriers and tunable diodes is explained, and the physics of surface plasmons on metal surfaces is outlined. Technical problems being addressed include phase-matching sunlight to surface plasmons, minimizing ohmic losses and reradiation in energy transport, coupling into the tunnels by mode conversion, and gaining an understanding of the tunnel-diode energy-conversion process. Diagrams illustrating the design concepts are provided.

Anderson, L. M.↗