Search NASA⌕ Search

SEARCH · Search NASA

Results for “simulation code”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Static Controls Performance Tool for Lunar Landers

This document presents a static analysis tool used to evaluate the controllability of Lunar landers. This was created as part of the NASA Lunar Cargo Transportation and Landing by Soft Touchdown (Lunar CATALYST) program. This tool is capable of accepting typical design information such as location and direction of thrusters, maximum thruster forces, gravity vectors, and center of mass locations. The tool evaluates how far the center of gravity can move from its starting position while still maintaining control. This type of analysis is intended to support results produced by time domain simulations. The code created for this project was implemented in Python, and it was designed to be integrated into systems level optimization tools to yield first-cut results on optimal thruster placement.

Aretskin-Hariton, Eliot D.↗

TPSAS-NF1676L-17553-DND

Investigate the potential of using an efficient damage imaging technique for damage identification by using a commercial finite element code to simulate the Lamb wave propagation in stiffened composite structures.

J T Wang↗

Determining the Cause of Reduced Concurrent Flame Spread over Thin Solid Fuels in Low Pressure and Low Gravity

The spread of flames over the surface of solid combustible materials is affected by the environmental conditions. Variables such as flow velocity, oxygen concentration, ambient pressure, partial gravity or microgravity, may change the material flammability and influence the fire dynamics. This is an important fire safety issue for space exploration vehicles and space habitats which will very likely have different environments than those currently used on the International Space Station, such as reduced pressure and enriched oxygen concentration (SEA). However, testing experimentally the materials to be used and qualified for space exploration under these conditions is a difficult and expensive task. Here, numerical modeling is used to understand the dominant physico-chemical processes on the concurrent flame spread over thin fabrics under reduced ambient pressure (and in turn, buoyancy) and variable gravitational conditions. The numerical model uses the Fire Dynamics Simulator (FDS6) code with a single-step Arrhenius reaction rate for the solid phase decomposition. Different models are tested for the gas phase combustion kinetics. The model results are validated with experimental results obtained at similar reduced ambient pressure and flow conditions at 1 g. It is shown that as ambient pressure is reduced the flame spread rate over a thin fabric is also reduced, both experimentally and numerically. Numerical results are compared to an analytical approach previously developed to explain the experimental trends. Further interpretation of the model results provides information regarding the physics of the process and how they are affected by the lower pressure environments and gravity conditions. The results of this work provide guidance for potential on-earth testing for fire safety design in spacecraft and space habitats.

Fire Safety↗

Determining the Cause of Reduced Concurrent Flame Spread over Thin Solid Fuels in Low Pressure and Low Gravity

The spread of flames over the surface of solid combustible materials is affected by the environmental conditions. Variables such as flow velocity, oxygen concentration, ambient pressure, partial gravity or microgravity, may change the material flammability and influence the fire dynamics. This is an important fire safety issue for space exploration vehicles and space habitats which will very likely have different environments than those currently used on the International Space Station, such as reduced pressure and enriched oxygen concentration (SEA). However, testing experimentally the materials to be used and qualified for space exploration under these conditions is a difficult and expensive task. Here, numerical modeling is used to understand the dominant physico-chemical processes on the concurrent flame spread over thin fabrics under reduced ambient pressure (and in turn, buoyancy) and variable gravitational conditions. The numerical model uses the Fire Dynamics Simulator (FDS6) code with a single-step Arrhenius reaction rate for the solid phase decomposition. Different models are tested for the gas phase combustion kinetics. The model results are validated with experimental results obtained at similar reduced ambient pressure and flow conditions at 1 g. It is shown that as ambient pressure is reduced the flame spread rate over a thin fabric is also reduced, both experimentally and numerically. Numerical results are compared to an analytical approach previously developed to explain the experimental trends. Further interpretation of the model results provides information regarding the physics of the process and how they are affected by the lower pressure environments and gravity conditions. The results of this work provide guidance for potential on-earth testing for fire safety design in spacecraft and space habitats.

microgravity↗

Laser Absorption Spectroscopy Measurements of Post-Shock Non-Equilibrium Species in the NASA Ames Electric Arc Shock Tube

The NASA Ames Electric Arc Shock Tube (EAST) is a unique facility capable of generating high enthalpy, shock-heated impulse gas flows representative of the kinetic and radiative conditions encountered by atmospheric entry vehicles. The facility maintains a successful history with emission spectroscopy, providing measurements of absolute radiance upon which various validation studies are anchored. The central objective of this work is to develop a comprehensive tunable diode laser absorption spectroscopy (TDLAS) sensing capability to provide complementary experimental insights to existing emission techniques. More specifically, a fast-scanning TDLAS-based diagnostic targeting the cyano radical (CN) in the near-infrared(near-IR) near 926.6 nm is employed in mixtures of 2.2% CH4in N2by mole for a sweep of incident shock velocities ranging 3.0-5.5 km/s and fill pressures 0.3-1.15 Torr. Laser scan rates up to 500 kHz probe multiple absorption features to provide quantitative measurements of temperature and species number density profiles behind the incident shock. In all instances, the temperature trend is consistent between emission-inferred and TDLAS-inferred measurements. However, at the lower-velocity conditions, there is an appreciable offset between the Data Parallel Line Relaxation Code (DPLR) simulation and experimental measurements. A similar behavior is observed in number density profiles, with emission measurements providing inferences of the CN(B) and CN(A) state, while TDLAS measurements provide an additional inference of the CN(X) state. In the fast-scanned experiments, measurement inferred number densities suggest a much faster production of CN at early times than captured by the model. This discrepancy motivates ongoing, additional spectroscopic and kinetics CN experiments to resolve the accuracy of modeling assumptions.

Efaine Chang↗

Coding Structures for Seated Row Simulation of an Active Controlled Vibration Isolation and Stabilization System for Astronaut’s Exercise Platform

Simulation for seated aerobic row exercise was a continued task to assist NASA in analyzing a one-dimensional vibration isolation and stabilization system for astronaut’s exercise platform. Feedback delay and signal noise were added to the simulation model. Simulation runs for this study were conducted in two software simulation tools, Trick and MBDyn, software simulation environments developed at the NASA Johnson Space Center. The exciter force in the simulation was calculated from motion capture of an exerciser during a seated aerobic row exercise. The simulation runs include passive control, active control using a Proportional, Integral, Derivative (PID) controller, and active control using a Piecewise Linear Integral Derivative (PWLID) controller. Output parameters include displacements of the exercise platform, the exerciser, and the counterweight; transmitted force to the wall of spacecraft; and actuator force to the platform. The simulation results showed excellent force reduction in the active controlled system compared to the passive controlled system, which resulted in less force reduction.

Simulation↗

Simulation of turbulent transonic separated flow over an airfoil

A code developed for simulating high Reynolds number transonic flow fields of arbitrary configuration is described. This code, in conjunction with laboratory experiments, is used to devise and test turbulence transport models which may be suitable in the prediction of such flow fields, with particular emphasis on regions of flow separation. The solutions describe the flow field, including both the shock-induced and trailing-edge separation regions, in sufficient detail to provide the profile and friction drag.

Deiwert, G. S.↗

Transonic Navier-Stokes wing solutions using a zonal approach. Part 2: High angle-of-attack simulation

A computer code is under development whereby the thin-layer Reynolds-averaged Navier-Stokes equations are to be applied to realistic fighter aircraft configurations. This transonic Navier-Stokes code (TNS) utilizes a zonal approach in order to treat complex geometries and satisfy in-core computer memory constraints. The zonal approach was applied to isolated wing geometries in order to facilitate code development. The TNS finite difference algorithm, zonal methodology, and code validation with experimental data is addressed. Also addressed are some numerical issues such as code robustness, efficiency, and accuracy at high angles of attack. Special free-stream-preserving metrics proved an effective way to treat H-mesh singularities over a large range of severe flow conditions, including strong leading edge flow gradients, massive shock induced separation, and stall. Furthermore, lift and drag coefficients were computed for a wing up through CLmax. Numerical oil flow patterns and particle trajectories are presented both for subcritical and transonic flow. These flow simulations are rich with complex separated flow physics and demonstrate the efficiency and robustness of the zonal approach.

Chaderjian, Neal M.↗

Transonic Navier-Stokes wing solutions using a zonal approach. Part 2: High angle-of-attack simulation

A computer code is under development whereby the thin-layer Reynolds-averaged Navier-Stokes equations are to be applied to realistic fighter-aircraft configurations. This transonic Navier-Stokes code (TNS) utilizes a zonal approach in order to treat complex geometries and satisfy in-core computer memory constraints. The zonal approach has been applied to isolated wing geometries in order to facilitate code development. Part 1 of this paper addresses the TNS finite-difference algorithm, zonal methodology, and code validation with experimental data. Part 2 of this paper addresses some numerical issues such as code robustness, efficiency, and accuracy at high angles of attack. Special free-stream-preserving metrics proved an effective way to treat H-mesh singularities over a large range of severe flow conditions, including strong leading-edge flow gradients, massive shock-induced separation, and stall. Furthermore, lift and drag coefficients have been computed for a wing up through CLmax. Numerical oil flow patterns and particle trajectories are presented both for subcritical and transonic flow. These flow simulations are rich with complex separated flow physics and demonstrate the efficiency and robustness of the zonal approach.

Chaderjian, N. M.↗

Summary of the GASP code application and evaluation effort for scramjet combustor flowfields

Numerical simulations of 3D turbulent mixing and reacting flows have been systematically evaluated by comparison with experimental data and other numerical solutions to provide confidence in the General Aerodynamic Simulation Program (GASP) code version 1.3. Specifically, the GASP flow solver has been used to model high speed flow through scram jet combustors. Unit injector problems evaluated include (1) UVA staged sonic normal injection of air into Mach 2 air stream, (2) the VPI Mach 1.7 low angled (15 deg) flush wall helium injection into an unconfined Mach 6 'cold air' stream, and (3) the HYPULSE angled (30 deg) flush wall hydrogen injection into a Mach 6, high enthalpy (flight Mach 17 simulation) nitrogen and air test gases. Results of the numerical simulation for the first two test cases have been compared with detailed in-stream measurements and with SPARK CFD solutions. The results for the last two cases have been compared with measured wall pressure and heat flux data and with SPARK CFD solutions. The present GASP solutions compare favorably with both the experimental data and the SPARK solutions.

Srinivasan, Shivakumar↗

New Tool Released for Engine-Airframe Blade-Out Structural Simulations

Researchers at the NASA Glenn Research Center have enhanced a general-purpose finite element code, NASTRAN, for engine-airframe structural simulations during steady-state and transient operating conditions. For steady-state simulations, the code can predict critical operating speeds, natural modes of vibration, and forced response (e.g., cabin noise and component fatigue). The code can be used to perform static analysis to predict engine-airframe response and component stresses due to maneuver loads. For transient response, the simulation code can be used to predict response due to bladeoff events and subsequent engine shutdown and windmilling conditions. In addition, the code can be used as a pretest analysis tool to predict the results of the bladeout test required for FAA certification of new and derivative aircraft engines. Before the present analysis code was developed, all the major aircraft engine and airframe manufacturers in the United States and overseas were performing similar types of analyses to ensure the structural integrity of engine-airframe systems. Although there were many similarities among the analysis procedures, each manufacturer was developing and maintaining its own structural analysis capabilities independently. This situation led to high software development and maintenance costs, complications with manufacturers exchanging models and results, and limitations in predicting the structural response to the desired degree of accuracy. An industry-NASA team was formed to overcome these problems by developing a common analysis tool that would satisfy all the structural analysis needs of the industry and that would be available and supported by a commercial software vendor so that the team members would be relieved of maintenance and development responsibilities. Input from all the team members was used to ensure that everyone's requirements were satisfied and that the best technology was incorporated into the code. Furthermore, because the code would be distributed by a commercial software vendor, it would be more readily available to engine and airframe manufacturers, as well as to nonaircraft companies that did not previously have access to this capability.

Lawrence, Charles↗

Julia Programming Language Benchmark Using a Flight Simulation

Julia’s goal to provide scripting language ease-of-coding with compiled language speed is explored. The runtime speed of the relatively new Julia programming language is assessed against other commonly used languages including Python, Java, and C++. An industry-standard missile and rocket simulation, coded in multiple languages, was used as a test bench for runtime speed. All language versions of the simulation, including Julia, were coded to a highly-developed object-oriented simulation architecture tailored specifically for time-domain flight simulation. A “speed-of-coding” second-dimension is plotted against runtime for each language to portray a space that characterizes Julia’s scripting language efficiencies in the context of the other languages. With caveats, Julia runtime speed was found to be in the class of compiled or semi-compiled languages. However, some factors that affect runtime speed at the cost of ease-of-coding are shown. Julia’s built-in functionality for multi-core processing is briefly examined as a means for obtaining even faster runtime speed. The major contribution of this research to the extensive language benchmarking body-of-work is comparing Julia to other mainstream languages using a complex flight simulation as opposed to benchmarking with single algorithms.

Sells, Ray↗

NNEP: The Navy NASA Engine Program

A computer code capable of simulating almost any conceivable turbine engine is described. This code uses stacked component maps and multiple flowpaths to simulate variable cycle engines with variable component geometry. It is capable of design and off-design (matching) calculations and can optimize free variables such as nozzle areas to minimize specific fuel consumption.

Fishbach, L. H.↗

Simulation of Laser Cooling and Trapping in Engineering Applications

An advanced computer code is undergoing development for numerically simulating laser cooling and trapping of large numbers of atoms. The code is expected to be useful in practical engineering applications and to contribute to understanding of the roles that light, atomic collisions, background pressure, and numbers of particles play in experiments using laser-cooled and -trapped atoms. The code is based on semiclassical theories of the forces exerted on atoms by magnetic and optical fields. Whereas computer codes developed previously for the same purpose account for only a few physical mechanisms, this code incorporates many more physical mechanisms (including atomic collisions, sub-Doppler cooling mechanisms, Stark and Zeeman energy shifts, gravitation, and evanescent-wave phenomena) that affect laser-matter interactions and the cooling of atoms to submillikelvin temperatures. Moreover, whereas the prior codes can simulate the interactions of at most a few atoms with a resonant light field, the number of atoms that can be included in a simulation by the present code is limited only by computer memory. Hence, the present code represents more nearly completely the complex physics involved when using laser-cooled and -trapped atoms in engineering applications. Another advantage that the code incorporates is the possibility to analyze the interaction between cold atoms of different atomic number. Some properties that cold atoms of different atomic species have, like cross sections and the particular excited states they can occupy when interacting with each other and light fields, play important roles not yet completely understood in the new experiments that are under way in laboratories worldwide to form ultracold molecules. Other research efforts use cold atoms as holders of quantum information, and more recent developments in cavity quantum electrodynamics also use ultracold atoms to explore and expand new information-technology ideas. These experiments give a hint on the wide range of applications and technology developments that can be tackled using cold atoms and light fields. From more precise atomic clocks and gravity sensors to the development of quantum computers, there will be a need to completely understand the whole ensemble of physical mechanisms that play a role in the development of such technologies. The code also permits the study of the dynamic and steady-state operations of technologies that use cold atoms. The physical characteristics of lasers and fields can be time-controlled to give a realistic simulation of the processes involved such that the design process can determine the best control features to use. It is expected that with the features incorporated into the code it will become a tool for the useful application of ultracold atoms in engineering applications. Currently, the software is being used for the analysis and understanding of simple experiments using cold atoms, and for the design of a modular compact source of cold atoms to be used in future research and development projects. The results so far indicate that the code is a useful design instrument that shows good agreement with experimental measurements (see figure), and a Windows-based user-friendly interface is also under development.

Ramirez-Serrano, Jaime↗

Simulation of Guided-Wave Ultrasound Propagation in Composite Laminates: Benchmark Comparisons of Numerical Codes and Experiment

Ultrasonic wave methods constitute the leading physical mechanism for nondestructive evaluation (NDE) and structural health monitoring (SHM) of solid composite materials, such as carbon fiber reinforced polymer (CFRP) laminates. Computational models of ultrasonic wave excitation, propagation, and scattering in CFRP composites can be extremely valuable in designing practicable NDE and SHM hardware, software, and methodologies that accomplish the desired accuracy, reliability, efficiency, and coverage. The development and application of ultrasonic simulation approaches for composite materials is an active area of research in the field of NDE. This paper presents comparisons of guided wave simulations for CFRP composites implemented using four different simulation codes: the commercial finite element modeling (FEM) packages ABAQUS, ANSYS, and COMSOL, and a custom code executing the Elastodynamic Finite Integration Technique (EFIT). Benchmark comparisons are made between the simulation tools and both experimental laser Doppler vibrometry data and theoretical dispersion curves. A pristine and a delamination type case (Teflon insert in the experimental specimen) is studied. A summary is given of the accuracy of simulation results and the respective computational performance of the four different simulation tools.

Composite↗

Simulations of a molecular plasma in collisional-radiative nonequilibrium

A code for the simulation of nonequilibrium plasmas is being developed, with the capability to couple the plasma fluid-dynamics for a single fluid with a collisional-radiative model, where electronic states are treated as separate species. The model allows for non-Boltzmann distribution of the electronic states. Deviations from the Boltzmann distributions are expected to occur in the rapidly ionizing regime behind a strong shock or in the recombining regime during a fast expansion. This additional step in modeling complexity is expected to yield more accurate predictions of the nonequilibrium state and the radiation spectrum and intensity. An attempt at extending the code to molecular plasma flows is presented. The numerical techniques used, the thermochemical model, and the results of some numerical tests are described.

Cambier, Jean-Luc↗

NASCAP simulation of PIX 2 experiments

The latest version of the NASCAP/LEO digital computer code used to simulate the PIX 2 experiment is discussed. NASCAP is a finite-element code and previous versions were restricted to a single fixed mesh size. As a consequence the resolution was dictated by the largest physical dimension to be modeled. The latest version of NASCAP/LEO can subdivide selected regions. This permitted the modeling of the overall Delta launch vehicle in the primary computational grid at a coarse resolution, with subdivided regions at finer resolution being used to pick up the details of the experiment module configuration. Langmuir probe data from the flight were used to estimate the space plasma density and temperature and the Delta ground potential relative to the space plasma. This information is needed for input to NASCAP. Because of the uncertainty or variability in the values of these parameters, it was necessary to explore a range around the nominal value in order to determine the variation in current collection. The flight data from PIX 2 were also compared with the results of the NASCAP simulation.

Roche, J. C.↗

Development of the US3D Code for Advanced Compressible and Reacting Flow Simulations

Aerothermodynamics and hypersonic flows involve complex multi-disciplinary physics, including finite-rate gas-phase kinetics, finite-rate internal energy relaxation, gas-surface interactions with finite-rate oxidation and sublimation, transition to turbulence, large-scale unsteadiness, shock-boundary layer interactions, fluid-structure interactions, and thermal protection system ablation and thermal response. Many of the flows have a large range of length and time scales, requiring large computational grids, implicit time integration, and large solution run times. The University of Minnesota NASA US3D code was designed for the simulation of these complex, highly-coupled flows. It has many of the features of the well-established DPLR code, but uses unstructured grids and has many advanced numerical capabilities and physical models for multi-physics problems. The main capabilities of the code are described, the physical modeling approaches are discussed, the different types of numerical flux functions and time integration approaches are outlined, and the parallelization strategy is overviewed. Comparisons between US3D and the NASA DPLR code are presented, and several advanced simulations are presented to illustrate some of novel features of the code.

CFD↗