Search NASA⌕ Search

SEARCH · Search NASA

Results for “solid-state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Low-cost DH and quantum well laser array development

The intial results of a program aimed at developing low-cost diode laser arrays for use as solid-state laser pumps are reported. MOCVD is used to demonstrate excellent run-to-run reproducibility in emission wavelength, threshold current density, and quantum efficiency. For this first experimental series, J(th) values of approximately 1310 Amps/sq cm were obtained for broad-area unthinned devices from the growth runs. Differential quantum efficiencies of between 41 percent and 47 percent were measured on the non-facet-coated devices from all four runs. Single quantum well, separate confinement heterostructure lasers fabricated from wafers grown in the same MOCVD reactor exhibited near single-mode emission, with J(th) values of approximately 300 Amps/sq cm. Photoluminescence data confirm quantum well widths of 80 A and 150 A for two different MOCVD growth runs.

Linden, Kurt J.↗
NASA NTRS1990

Demonstration of a low bandwidth 1.06-micron optical phase-locked loop for coherent homodyne communication

A type II 1.06-micron optical phase-locked loop (OPLL) for use in a coherent homodyne receiver is discussed. Diode-laser-pumped solid-state lasers are used for both the local oscillator and transmitter, because their phase noise is significantly lower than that of diode lasers. Closed-loop RMS phase noise of less than 12 mrad (0.69 deg) is achieved, and modulation-demodulation in bulk modulators at rates from 20 kHz to 20 MHz with less than 19 deg of modulation depth is demonstrated.

Day, T.↗
NASA NTRS1989

Applications of surface analysis and surface theory in tribology

Tribology, the study of adhesion, friction and wear of materials, is a complex field which requires a knowledge of solid state physics, surface physics, chemistry, material science, and mechanical engineering. It has been dominated, however, by the more practical need to make equipment work. With the advent of surface analysis and advances in surface and solid-state theory, a new dimension has been added to the analysis of interactions at tribological interfaces. In this paper the applications of tribological studies and their limitations are presented. Examples from research at the NASA Lewis Research Center are given. Emphasis is on fundamental studies involving the effects of monolayer coverage and thick films on friction and wear. A summary of the current status of theoretical calculations of defect energetics is presented. In addition, some new theoretical techniques which enable simplified quantitative calculations of adhesion, fracture, and friction are discussed.

Ferrante, John↗
NASA NTRS1989

Imaging spectrometry in the post-EOS era

It is argued that the next generation of imaging spectrometers will need greater capabilities and more flexibility than the High Resolution Imaging Spectrometer (HIRIS) and the Moderate Resolution Imaging Spectrometer (MODIS), which were designed for the first Earth Observation System platform. The emerging technology that represents a major advance in the scientific utility of imaging spectrometry is the acoustooptic tunable filters, (AOTFs). AOTFs are compact robust solid-state crystals which provide rapid (millisecond) electronically-controlled spectral tunability. This paper discusses the evolving requirements of imaging spectrometers and examines the basic system parameters of the HIRIS and the MODIS concepts involving the use of AOTFs, which will satisfy these requirements.

Duval, Valerie G.↗
NASA NTRS1990

Optical synchronization of millimeter-wave oscillators for distributed architecture

A review of various methods of phase and frequency synchronization of active MMIC based transmit/receive modules is presented, and particular emphasis is placed on the synchronization of oscillators through the use of an indirect subharmonic optical injection locking technique. In this approach, the nonlinear behavior of large-signal modulated laser diodes and solid-state oscillators is exploited to extend the bandwidth of the synchronizing link to the millimeter-wave frequency range. Experimental results of the phase and frequency coherency of two 21.5 GHz FET oscillators are reported. Optimum performance is achieved at a subharmonic factor of 1/4, with a locking range of 84 MHz and a phase noise degradation of only 14 dB. The phase coherency measurement of two injection-locked oscillators points to a phase shift, which is introduced as a result of the frequency detuning between the slave and master oscillator signals. A scheme to correct for this phase error is presented.

Daryoush, Afshin S.↗
NASA NTRS1990

Electromechanical propellant control system actuator

New control mechanism technologies are currently being sought to provide alternatives to hydraulic actuation systems. The Propulsion Laboratory at Marshall Space Flight Center (MSFC) is involved in the development of electromechanical actuators (EMA's) for this purpose. Through this effort, an in-house designed electromechanical propellant valve actuator has been assembled and is presently being evaluated. This evaluation will allow performance comparisons between EMA and hydraulics systems. The in-house design consists of the following hardware: a three-phase brushless motor, a harmonic drive, and an output spline which will mate with current Space Shuttle Main Engine (SSME) propellant control valves. A resolver and associated electronics supply position feedback for the EMA. System control is provided by a solid-state electronic controller and power supply. Frequency response testing has been performed with further testing planned as hardware and test facilities become available.

Myers, W. Neill↗
NASA NTRS1989

Fabrication and evaluation of enhanced diffusion bonded titanium honeycomb core sandwich panels with titanium aluminide face sheets

A joining process was developed for fabricating lightweight, high temperature sandwich panels for aerospace applications using Ti-14Al-21Nb face sheets and Ti-3Al-2.5V honeycomb core. The process, termed Enhanced Diffusion Bonding (EDB), relies on the formation of a eutectic liquid through solid-state diffusion at elevated temperatures and isothermal solidification to produce joints in thin-gage titanium and titanium aluminide structural components. A technique employing a maskant on the honeycomb core was developed which permitted electroplating a controlled amount of EDB material only on the edges of the honeycomb core in order to minimize the structural weight and metallurgical interaction effects. Metallurgical analyses were conducted to determine the interaction effects between the EDB materials and the constituents of the sandwich structure following EDB processing. The initial mechanical evaluation was conducted with butt joint specimens tested at temperatures from 1400 - 1700 F. Further mechanical evaluation was conducted with EDB sandwich specimens using flatwise tension tests at temperatures from 70 - 1100 F and edgewise compression tests at ambient temperature.

Hoffmann, E. K.↗
NASA NTRS1989

An airborne C-band scatterometer for remote sensing the air-sea interface

An airborne C-band scatterometer system (C-Scat) has been developed for remote sensing of the air-sea interface. The sensor has been designed to fly on a number of research aircraft, beginning with the NASA Ames Research Center's C-130B, on which test flights were conducted in August of 1988. The scatterometer utilizes a 10-W solid-state power amplifier and a frequency-steered microstrip array antenna which is installed beneath the fuselage of the airplane. The antenna is electrically scanned in elevation from 20 to 50 deg off nadir, and it is mechanically rotated 360 deg in azimuth. The system is fully computer controlled and is capable of accurately measuring ocean-surface normalized radar cross section (NRCS) from altitudes as high as 25,000 feet. It has been developed to study the relationship between NRCS and ocean-surface roughness influences such as wind speed and direction, wave height and slope, and air-sea temperature difference.

Mclaughlin, D. J.↗
NASA NTRS1990

Wave-particle interactions on the FAST satellite

NASA's Fast Auroral Snapshot, or 'FAST' satellite, scheduled for launch in 1993, will investigate the plasma physics of the low altitude auroral zone from a 3500-km apogee polar orbit. FAST will give attention to wave, double-layer, and soliton production processes due to electrons and ions, as well as to wave-wave interactions, and the acceleration of electrons and ions by waves and electric fields. FAST will employ an intelligent data-handling system capacle of data acquisition at rates of up to 1 Mb/sec, in addition to a 1-Gbit solid-state memory. The data need be gathered for only a few minutes during passes through the auroral zone, since the most interesting auroral phenomena occur in such narrow regions as auroral arcs, electrostatic shocks, and superthermal electron bursts.

Temerin, M. A.↗
NASA NTRS1989

Coherent communication link using diode-pumped lasers

Work toward developing a diffraction limited, single frequency, modulated transmitter suitable for coherent optical communication or direct detection communication is discussed. Diode pumped, monolithic Nd:YAG nonplanar ring oscillators were used as the carrier beam. An external modulation technique which can handle high optical powers, has moderate modulation voltage, and which can reach modulation rates of 1 GHz was invented. Semiconductor laser pumped solid-state lasers which have high output power (0.5 Watt) and which oscillate at a single frequency, in a diffraction limited beam, at the wavelength of 1.06 microns were built. A technique for phase modulating the laser output by 180 degrees with a 40-volt peak to peak driving voltage is demonstrated. This technique can be adapted for amplitude modulation of 100 percent with the same voltage. This technique makes use of a resonant bulk modulator, so it does not have the power handling limitations of guided wave modulators.

Kane, Thomas J.↗
NASA NTRS1982

Observation of an Excess Current Noise Resulting from Oxygen Absorption onto Iron Films

This paper reports on measurements that demonstrate that oxygen absorbed on clean polycrystalline Fe films can produce an excess current noise. The noise is indicative of dynamic processes occurring in the surface region of the film. We propose that the noise results from the dynamics of a reversible reaction between absorbed states. The measurements are accurately modeled with a single correlation time implying that surface heterogeneity is not important to the reaction. In addition to offering promise for future states of solid-state surface reactions, these measurements also have implications for the origin of 1/f current noise in conductors.

Shanabarger, M. R.↗
NASA NTRS1982

Pressure Measurement

Pressure Systems, Inc.'s DPT 6400 is a system designed to increase productivity in industrial processes where there is a need for making multiple pressure measurements quickly and with high accuracy. It is applicable in controlling industrial processes in plants that are being upgraded to automated status. In order to automate such plants the pressures at the many loops must be measured, converted to digital information and transmitted to the plant's process control computer. The DPT 6400 serves that function. By employing solid-state pressure sensing transducers whose errors are automatically corrected by a microprocessor, it is capable of highly accurate pressure measurements. Basic DPT 6400 has 64 channels, but the system can be expanded to 256 channels by the addition of "slave" units.

Source record↗
NASA NTRS1980

Emergency/Night Lightning

UDEC's highly efficient lighting system is finding wide acceptance among industrial and commercial firms as an energy savings means of providing emergency and night lighting. Originating from Skylab, the system consists of small high frequency fluorescent light fixtures powered by solar cells. Advantages of UDEC's lighting system stem from high reliability and high light output with very low energy drain. Principal components of system are long life fluorescent lamps operated by electronic circuitry, a sealed gelatine cell battery that needs no maintenance for eight years and a solid-state automatic battery charger. Installation of UDEC lighting in a company's six-and-a-half acre warehouse office cut the annual night lighting electric bill from $8,000 a year to $300 per year.

Source record↗
NASA NTRS1977

Emergency Lighting

A lighting system originally developed for NASA's Apollo and Skylab manned spacecraft resulted in a industrial spinoff and creation of a whole new company to produce and market the product line. The company is UDEC Corp., Waltham, Mass. UDEC's "Multi-Mode" electronic lighting systems are designed for plant emergency and supplemental use, such as night lighting, "always-on" stairwell lights and illuminated exit signs. Their advantages stem from the qualities demanded for spacecraft installation: extremely high fight output with very low energy drain, compactness, light weight, and high reliability. The Multi-Mode system includes long-life fluorescent lamps operated by electronic circuitry, a sealed battery that needs no maintenance for 10 years, and a solid-state battery charger. A typical emergency installation consists of a master module with battery and an eight watt lamp, together with four remote "Satellight" modules powered by the master's battery. As a night lighting system for maintenance or I security, UDEC fixtures can bypass the battery and 1 operate on normal current at a fraction of the energy 1 demand of conventional night lighting. Industrial customers have realized savings of better than ninety percent with UDEC night lights. UDEC started as a basement industry in 1972 but the company has already sold more than 1,000 lighting systems to building operators.

Source record↗
NASA NTRS1977

Breadboard Facility

In the sixties, Chrysler was NASA's prime contractor for the Saturn I and IB test launch vehicles. The company installed and operated at Huntsville what was known as the Saturn I/IB Development Breadboard Facility. "Breadboard," means an array of electrical and electronic equipment for performing a variety of development and test functions. This work gave Chrysler a broad capability in computerized testing to assure quality control in development of solid-state electronic systems. Today that division is manufacturing many products not destined for NASA, most of them being associated with the company's automotive line. A major project is production and quality-control testing of the "lean-burn" engine, one that has a built-in Computer to control emission timing, and allow the engine to run on a leaner mixture of fuel and air. Other environment-related products include vehicle emission analyzers. The newest of the line is an accurate, portable solid state instrument for testing auto exhaust gases. The exhaust analyzers, now being produced for company dealers and for service

Source record↗
NASA NTRS1977

Multiple high voltage output DC-to-DC power converter

Disclosed is a multiple output DC-to-DC converter. The DC input power is filtered and passed through a chopper preregulator. The chopper output is then passed through a current source inverter controlled by a squarewave generator. The resultant AC is passed through the primary winding of a transformer, with high voltages induced in a plurality of secondary windings. The high voltage secondary outputs are each solid-state rectified for passage to individual output loads. Multiple feedback loops control the operation of the chopper preregulator, one being responsive to the current through the primary winding and another responsive to the DC voltage level at a selected output.

Cronin, Donald L.↗
NASA NTRS1961

Neutralization of Hydroxide Ion in Melt-Grown NaCl Crystals

Many recent studies of solid-state phenomena, particularly in the area of crystal imperfections, have involved the use of melt-grown NaCl single crystals. Quite often trace impurities in these materials have had a prominent effect on these phenomena. Trace amounts of hydroxide ion have been found in melt-grown NaCl crystals. This paper describes a nondestructive method of neutralizing the hydroxide ion in such crystals. Crystals of similar hydroxide content are maintained at an elevated temperature below the melting point of NaCl in a flowing atmosphere containing. dry hydrogen chloride. Heat treatment is continued until an analysis of the test specimens shows no excess hydroxide ion. A colorimetric method previously described4 is used for this analysis.

Otterson, Dumas A.↗