Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface alloying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Graphite/copper alloy interfacial energies determined using the sessile drop method

Graphite surfaces are not wet by pure copper. This lack of wetting is responsible for a debonding phenomenon that was found in continuous graphite fiber/copper matrix composites materials subjected to elevated temperatures. By suitably alloying copper, its capability to wet graphite surfaces can be enhanced. In situ measurements of graphite/copper alloy wetting angles were made using the sessile drop method. Interfacial energy values were calculated based upon these measurements.

Devincent, Sandra M.↗
NASA NTRS1973

Eutectic superalloys strengthened by sigma, Ni3CB lamellae and gamma prime, Ni3Al precipitates

By means of a screening and solidification optimization study of certain alloys located on the gamma-sigma liquidus surface within the Ni-Cb-Cr-Al system, alloys with high temperature properties superior to those of all known superalloys were defined. One alloy, Ni - 19.7w/o Cb - 6.0w/o Cr - 2.5w/o Al, directionally solidified at 3 cm/hr met or exceeded each program goal. A second alloy, Ni-21.75 w/o Cb-2.55 w/o Al, although deficient in its inherent oxidation resistance, met the other program goals and combined a remarkable insensitivity of composite microstructure to solidification parameters with excellent low temperature toughness. This investigation demonstrated that useful properties for gas turbine airfoil application have been achieved by reinforcing a strong and tough gamma solid solution matrix containing precipitated gamma prime by a lamellar intermetallic compound Ni3 Cb having greater strength at elevated temperature.

Lemkey, F. D.↗
NASA NTRS1995

Shape-Memory-Alloy Actuator For Flight Controls

Report proposes use of shape-memory-alloy actuators, instead of hydraulic actuators, for aerodynamic flight-control surfaces. Actuator made of shape-memory alloy converts thermal energy into mechanical work by changing shape as it makes transitions between martensitic and austenitic crystalline phase states of alloy. Because both hot exhaust gases and cryogenic propellant liquids available aboard launch rockets, shape-memory-alloy actuators exceptionally suited for use aboard such rockets.

Barret, Chris↗
NASA NTRS1982

Metal shell technology based upon hollow jet instability

Spherical shells of submillimeter size are sought as ICF targets. Such shells must be dimensionally precise, smooth, of high strength, and composed of a high atomic number material. A technology for the production of shells based upon the hydrodynamic instability of an annular jet of molten metal is described. Shells in the 0.7-2.0 mm size range have been produced using tin as a test material. Specimens exhibit good sphericity, fair concentricity, and excellent finish over most of the surface. Work involving a gold-lead-antimony alloy is in progress. Droplets of this are amorphous and possess superior surface finish. The flow of tin models that of the alloy well; experiments on both metals show that the technique holds considerable promise.

Kendall, J. M.↗
DOE OSTI2026

Quasi-In-Situ Analysis of Electrode Top Atomic Layers via High-Sensitivity Low-Energy Ion Scattering and Potential-Controlled Sample Transfer

Electrocatalytic reactions involve interfacial interactions between the surfaces of electrodes and reactive species at an electrolyte interface. There are presently no universal or unambiguous methods to directly assay the active top atomic layer composition that influences the reactivity of these electrodes under relevant operating conditions. Low-energy ion scattering (LEIS) spectroscopy is a surface characterization technique that yields compositional analysis of the outermost atomic layer of a material, but it must be performed in ultrahigh vacuum (UHV). Application of LEIS measurements to electrochemical materials that are removed from ambient liquid-phase environments thus leaves an open question as to whether the surface that is transferred to UHV is truly the surface that manifested during the electrochemical reaction. Toward the goal of preserving the active surface state, we developed a sample transfer workflow for LEIS enabling air-free removal and drying of an electrode from an electrochemical cell while maintaining control of the potential using an auxiliary electrode. The potential-controlled emersion method was demonstrated to give distinct potential-dependent surface compositions for a Cu−Pd alloy relative to removal after uncontrolled return to open-circuit potential. A Cu-enriched surface was found at anodic potential and a Pd-enriched surface at cathodic potential, suggesting that the approach can be used to retain representative atomic configurations during transfer. Since adsorbates will often persist from the reaction environment, conventional sample pretreatment methods for removal, including atomic O and atomic H exposure, were also contrasted. Both methods were found to differ with results from incidental low-dose depth profiling by the LEIS primary ion source, which removes adventitious species and surface atoms during the course of repeated measurements. These depth profiles were found to be sensitive to sample history and thus qualitatively informative, despite the possible changes induced by ion damage. The results exhibit (i) the need for complete control over the polarization state of the sample at all times (no excursions to open circuit during transfer) and (ii) the utility of low-dose depth profiling to capture changes in the near-surface composition.

Alloys↗
NASA NTRS1983

Stress-corrosion behavior of aluminum-lithium alloys in aqueous environments

The stress corrosion susceptibility of two powder metallurgy (P/M) alloys, Al-Li-Cu and Al-Li-Cu-Mg two mechanically attrited (M/A) alloys, Al-Li-Cu and Al-Li-Mg; and two wrought, ingot alloys, X-2020 and AA7475, are compared. Time-dependent fracture in an aqueous sodium chloride environment under alternate immersion condition was found to vary significantly between alloys. The stress corrosion behavior of the two powder metallurgy processed alloys was studied in detail under conditions of crack initiation, static crack growth, and fatigue crack growth. A variety of stress corrosion tests were performed including smooth surface, time-to-failure tests; potentiostatic tests on smooth surfaces exposed to constant applied strain rates; and fracture mechanics-type tests under static and cyclic loads. Both alloys show surface pitting and subsequent intergranular corrosion. Pitting is more severe in the magnesium-bearing alloy and is associated with stringer particles strung along the extrusion direction as a result of P/M processing.

Pizzo, P. P.↗
NASA NTRS1984

Stress-corrosion behavior of aluminum-lithium alloys in aqueous salt environments

The stress corrosion susceptibility of two powder metallurgy (P/M) alloys, Al-Li-Cu and Al-Li-Cu-Mg; two mechanically attrited (M/A) alloys, Al-Li-Cu and Al-Li-Mg; and two wrought, ingot alloys, X-2020 and AA7475, are compared. Time-dependent fracture in an aqueous sodium chloride environment under alternate immersion condition was found to vary significantly between alloys. The stress corrosion behavior of the two powder metallurgy processed alloys was studied in detail under conditions of crack initiation, static crack growth, and fatigue crack growth. A variety of stress corrosion tests were performed including smooth surface, time-to-failure tests; potentiostatic tests on smooth surfaces exposed to constant applied strain rates; and fracture mechanics-type tests under static and cyclic loads. Both alloys show surface pitting and subsequent intergranular corrosion. Pitting is more severe in the magnesium-bearing alloy and is associated with stringer particles strung along the extrusion direction as a result of P/M processing.

Pizzo, P. P.↗
DOE OSTI2024

Creation of Multi-Principal Element Alloy NiCoCr Nanostructures via Nanosecond Laser-Induced Dewetting

The multi-principal element alloy nanoparticles (MPEA NPs), a new class of nanomaterials, present a highly rewarding opportunity to explore new or vastly different functional properties than the traditional mono/bi/multimetallic nanostructures due to their unique characteristics of atomic-level homogeneous mixing of constituent elements in the nanoconfinements. Here, in this paper, the successful creation of NiCoCr nanoparticles, a well-known MPEA system is reported, using ultrafast nanosecond laser-induced dewetting of alloy thin films. Nanoparticle formation occurs by spontaneously breaking the energetically unstable thin films in a melt state under laser-induced hydrodynamic instability and subsequently accumulating in a droplet shape via surface energy minimization. While NiCoCr alloy shows a stark contrast in physical properties compared to individual metallic constituents, i.e., Ni, Co, and Cr, yet the transient nature of the laser-driven process facilitates a homogeneous distribution of the constituents (Ni, Co, and Cr) in the nanoparticles. Using high-resolution chemical analysis and scanning nanodiffraction, the environmental stability and grain arrangement in the nanoparticles are further investigated. Thermal transport simulations reveal that the ultrashort (≈100 ns) melt-state lifetime of NiCoCr during the dewetting event helps retain the constituent elements in a single-phase solid solution with homogenous distribution and opens the pathway to create the unique MPEA nanoparticles with laser-induced dewetting process.

36 MATERIALS SCIENCE↗
NASA NTRS1986

Containerless processing of hypermonotectic and glass forming alloys using the Marshall Space Flight Center 100 meter drop tube facility

Two separate projects were carried out to study alloys whose solidification structures can be strongly influenced by the presence of a container during melting and solidifications. One project involved containerless solidification of hypermonotectic Au35Rh65 alloys. This alloy exhibits liquid immiscibility over a temperature range. It has been suggested that containerless melting might be one solution to the problem of sedimentation in the dispersions of immiscible liquid phases. However, surface tension driven flows could also lead to accumulation of the minority liquid phase at the external surface of a containerlessly melted alloy. The research underway is a first step in determining the influence of containerless, microgravity processing on immiscible alloys. Nickel-niobium alloys were studied using the drop tube facility. One alloy in this system, a Ni60Nb40 alloy, is a good candidate for the formation of a bulk metallic glass. Amorphous alloys of this composition were produced using thin film and mechanical alloying techniques. However, theory indicates that if heterogeneous nucleation can be avoided, it should be possible to produce an amorphous structure in this system using a moderate cooling rate from the melt. The containerless melting and solidification capabilities of the drop tube faciltiy provide ideal conditions for a study of this type. To date, several Ni60Nb40 samples have been levitated, melted and cooled during 4.6 seconds of free fall in the 100 meter drop tube. Structures obtained are discussed.

Andrews, J. B.↗
DOE OSTI2023

From Inside Out: How the Buried Interface, Shell Defects, and Surface Chemistry Conspire to Determine Optical Performance in Nonblinking Giant Quantum Dots

“Giant” or core/thick‐shell quantum dots (gQDs) are an important class of solid‐state quantum emitter characterized by strongly suppressed blinking and photobleaching under ambient conditions, and reduced nonradiative Auger processes. Together, these qualities provide distinguishing and useful functionality as single‐ and ensemble‐photon sources. For many applications, operation at elevated temperatures and under intense photon flux is desired, but performance is strongly dependent on the synthetic method employed for thick‐shell growth. Here, a comprehensive analysis of gQD structural properties “from the inside out” as a function of shell‐growth method is reported: successive ionic layer adsorption and reaction (SILAR) and high‐temperature continuous injection (HT‐CI), or sequential combinations of the two. Key correlations across synthesis methods, structural features (interfacial alloying, stacking‐fault density and surface‐ligand identity), and performance metrics (quantum yield, single‐gQD photoluminescence under thermal/photo stress, charging behavior and quantum‐optical properties) are identified. Surprisingly, it is found that interfacial alloying is the strongest indicator of gQD stability under stress, but this parameter is not the determining factor for Auger suppression. Furthermore, quantum yield is strongly influenced by surface chemistry and can approach unity even in the case of high shell‐defect density, while introduction of zinc‐blende stacking faults increases the likelihood that a gQD exhibits charged‐state emission.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Corrosion characteristics of Mo and TZM alloy for plasma facing components in molten lithium at 623 K

Here, in this study, the corrosion behaviours of molybdenum (Mo) and a Mo-based alloy (TZM) were investigated using a static immersion corrosion technique. Weight loss, surface microstructure, and corrosion depth of Mo and the TZM alloy were correlated with elements. The compatibility of Mo and the TZM alloy in static liquid Li was suitable. Mo demonstrated uniform corrosion with a homogenous dissolution of free C and Mo, and TZM alloy exhibited a nonuniform corrosion behaviour with a preferential grain boundary attack caused by the selective dissolution of free C, Ti, and Zr. When the surface oxidation layer of the samples was consumed, free C from Mo and TZM diffused into molten Li to form Li 2 C 2 and then was captured by Zr, Ti, and Mo to form thermodynamically stable carbides, which resulted in the enrichment of the C layer near the sample surfaces. In addition, Ti and Zr acted as N-trappers in liquid Li; the formation of Zr and Ti nitrides resulted in the enrichment of N, Ti, and Zr elements on the surface and led to TZM corrosion increase. Thus, Zr and Ti depletion, pitting, and grain boundary corrosion were problematic for TZM under long-term exposure to liquid Li. Reducing the content of free C and nonmetallic N and increasing the amount of Ti and Zr carbides on the surface of and inside the raw TZM alloy helped improve the corrosion resistance of TZM in liquid Li.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Functionalized PdAu Alloy on Nanocones Fabricated on Optical Fibers for Hydrogen Sensing

This paper reports the development of fiber optical hydrogen sensors using palladium and gold alloy nanostructures as sensor materials for hydrogen measurements using a D-shaped fiber as a platform. Using a maskless reactive ion etching technique, silica nanocone structures were formed on the surface of the D-shaped fiber. Palladium and gold alloys were deposited on the surface of nanostructured D-shaped fiber to form a nano-alloy sensor film. Evanescent interaction between guided light propagated in the fiber core and nano-alloy enabled highly sensitive hydrogen detection from concentrations that ranged from 0.25% to 10% in atmosphere pressure. Here, the formation of nanostructured alloy enabled by the nanocone surface led to more than 3 times faster in sensor response time and significant improvements in sensor sensitivity and reversibility. The work presented here demonstrates that highly controllable VLSI microfabrication schemes can be applied to produce nanostructured sensor films on optical fibers for high-sensitivity chemical sensing.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Design of Silicide-Strengthened Nb–Si–Cr–(Mo) alloys for additive manufacturing

Three high–intermetallic volume Nb–Si–Cr–(Mo) alloys were designed using CALPHAD modeling with the goal of identifying high–specific strength, oxidation-resistant alloys that can be additively manufactured using powder bed fusion. The silicides Nb 5 Si 3 and Nb 9 Si 2 Cr3 were targeted as the primary strengthening phases, and the addition of Cr promoted the NbCr 2 phase. These alloys were cast and surface-processed with electron beam welding at different speeds to simulate additive manufacturing, and the phases and microstructures of both cast and welded regions were characterized. The weld processing was found to produce fine-grained microstructures in each alloy with fine-scale intermetallics uniformly distributed among a body-centered cubic Nb matrix. Microstructural refinement and hardness were found to increase with weld velocity; one alloy reached its highest hardness of approximately 16 GPa before the brittleness at higher velocities became detrimental. One alloy was found to be qualitatively the least brittle while also attaining a hardness of 13 GPa and was therefore identified as a good candidate for additive manufacturing.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Constellation-X Spectroscopy X-Ray Telescope Requirements and Development Program: MSFC Research Program

The Constellation-X Spectroscopy X-ray Telescope (SXT) will provide high-throughput, high-resolution spectroscopy of cosmic sources, from 0.25 keV to 10 keV. Key to this capability is the development of large (1.6 m diameter), lightweight optics for the SXT mirror assembly. Teams led by NASA's Marshall Space Flight Center (MSFC), by NASA's Goddard Space Flight Center (GSFC), and by Italy's Osservatorio Astronomico di Brera (OAB) are currently developing competing mirror technologies for this planned mission. Each team is making significant research progress in developing mirror technologies which satisfy the SXT requirements for lightweight optics, consistent with a system-level optical performance of better than 15 arcsec half-power diameter. The NASA Marshall Space Flight Center (MSFC), in collaboration with the Smithsonian Astrophysical Observatory (SAO), has focussed its efforts on full-shell replicated optics, of electroformed nickel alloys. Recent progress in identifying a surface treatment to effect low, controlled adhesion and, more significantly, in developing new high-strength nickel alloys make this a viable, low cost approach to satisfying the SXT requirements.

O'Dell, S. L.↗
NASA NTRS2015

Low Cost, Upper Stage-Class Propulsion

The low cost, upper stage-class propulsion (LCUSP) element will develop a high strength copper alloy additive manufacturing (AM) process as well as critical components for an upper stage-class propulsion system that will be demonstrated with testing. As manufacturing technologies have matured, it now appears possible to build all the major components and subsystems of an upper stage-class rocket engine for substantially less money and much faster than traditionally done. However, several enabling technologies must be developed before that can happen. This activity will address these technologies and demonstrate the concept by designing, manufacturing, and testing the critical components of a rocket engine. The processes developed and materials' property data will be transitioned to industry upon completion of the activity. Technologies to enable the concept are AM copper alloy process development, AM post-processing finishing to minimize surface roughness, AM material deposition on existing copper alloy substrate, and materials characterization.

Vickers, John↗
NASA NTRS1981

Ion beam sputter etching of orthopedic implanted alloy MP35N and resulting effects on fatigue

The effects of two types of argon ion sputter etched surface structures on the tensile stress fatigue properties of orthopedic implant alloy MP35N were investigated. One surface structure was a natural texture resulting from direct bombardment by 1 keV argon ions. The other structure was a pattern of square holes milled into the surface by a 1 keV argon ion beam through a Ni screen mask. The etched surfaces were subjected to tensile stress only in fatigue tests designed to simulate the cyclic load conditions experienced by the stems of artificial hip joint implants. Both types of sputter etched surface structures were found to reduce the fatigue strength below that of smooth surface MP35N.

Wintucky, E. G.↗