Search NASA⌕ Search

SEARCH · Search NASA

Results for “Absorber design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Adapting Optimal Velocity Tracking Control to Account for WEC Constraints and Power-Take-Off Efficiencies: Preprint

Wave energy converters (WECs) come in many different forms, from point absorbers, oscillating water columns, to bulge wave devices. This paper focuses on the control of point absorber WECs, which typically have a narrow-banded frequency response and, therefore, control is well placed to improve the energy capture of such WECs. The acausal nature of the control problem means that theoretically optimal control is almost impossible to achieve inpractice; however optimal velocity tracking (OVT) offers a simple and robust approximation to optimal control that can achieve better power capture than passive linear damping methods, albeit with necessarily higher force demands. OVT is a form of impedance matching and the magnitude of the power-take off (PTO) force demand is often not linearly proportional to the WEC velocity, which can lead to PTO force and speed combinations far from the optimalPTO efficiency. The highly non-linear PTO force and speed to efficiency mapping can, without remedial measures, severely diminish the effectiveness of OVT techniques. In this paper, limits to the movement and force of the PTO are demonstrated, allowing OVT to be more easily applied in practice. The effect of PTO efficiency is explored, and a potential solution to the problem of adapting control to account for efficiency is presented. Both aspects of the work presented highlight the requirement for co-design of the WEC, PTO, and controller.

conversion efficiency↗
DOE OSTI2022

A P-61 Black Widow Inspired Palladium Biladiene Complex for Efficient Sensitization of Singlet Oxygen Using Visible Light

Photodynamic therapy (PDT) is a promising treatment option that ablates cancerous cells and tumors via photoinduced sensitization of singlet oxygen. Over the last few decades, much work has been devoted to the development of new photochemotherapeutic agents for PDT. A wide variety of macrocyclic tetrapyrrole based photosensitizers have been designed, synthesized and characterized as PDT agents. Many of these complexes have a variety of issues that pose a barrier to their use in humans, including biocompatibility, inherent toxicity, and synthetic hurdles. We have developed a non-traditional, non-cyclic, and non-aromatic tetrapyrrole ligand scaffold, called the biladiene (DMBil1), as an alternative to these traditional photosensitizer complexes. Upon insertion of a heavy atom such as Pd 2+ center, Pd[DMBil1] generates singlet oxygen in substantial yields (Φ Δ = 0.54, λ exc = 500 nm) when irradiated with visible light. To extend the absorption profile for Pd[DMBil1] deeper into the phototherapeutic window, the tetrapyrrole was conjugated with alkynyl phenyl groups at the 2- and 18-positions (Pd[DMBil2-PE]) resulting in a significant redshift while also increasing singlet oxygen generation (Φ Δ = 0.59, 600 nm). To further modify the dialkynyl-biladiene scaffold, we conjugated a 1,8-diethynylanthracene with to the Pd[DMBil1] tetrapyrrole in order to further extend the compound’s π-conjugation in a cyclic loop that spans the entire tetrapyrrole unit. This new compound (Pd[DMBil2-P61]) is structurally reminiscent of the P61 Black Widow aircraft and absorbs light into the phototherapeutic window (600–900 nm). In addition to detailing the solid-state structure and steady-state spectroscopic properties for this new biladiene, photochemical sensitization studies demonstrated that Pd[DMBil2-P61] can sensitize the formation of 1 O 2 with quantum yields of Φ Δ = 0.84 upon irradiation with light λ = 600 nm. These results distinguish the Pd[DMBil2-P61] platform as the most efficient biladiene-based singlet oxygen photosensitizer developed to date. When taken together, the improved absorption in the phototherapeutic window and high singlet oxygen sensitization efficiency of Pd[DMBil2-P61] mark this compound as a promising candidate for future study as an agent of photodynamic cancer therapy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Tailoring electron transfer pathway for photocatalytic N 2 -to-NH 3 reduction in a CdS quantum dots-nitrogenase system

The combination of abiotic photosensitizers with purified enzymes in a biohybrid system offers a promising pathway to utilizing light to accomplish challenging chemical transformations and provides insights into the rational photocatalytic system design for efficient solar-to-chemical energy conversion. In this work, we demonstrate a hybrid photocatalytic system for ammonia production from N2 by combining cadmium sulfide quantum dots (CdS QDs) and Mo-nitrogenase from Azotobacter vinelandii, composed of the iron protein (FeP) and the molybdenum-iron protein (MoFeP). Photoexcited electrons from the CdS QD are delivered by an electron transfer mediator through the FeP to the catalytic MoFeP. The complete system was optimized for the ligand on the CdS QDs, mediators, and reaction conditions. The best results were achieved with β-mercaptoethanol as a QD ligand. The mediator test revealed that 1,1'-bis(3-sulfonatopropyl)-4,4'-bipyridinium (SPr)2V (-0.4 V vs. NHE) supports the reduction of protons and N 2 to H 2 and ammonia catalyzed by nitrogenase. However, in the presence of 1,1'-trimethylene-2,2'-bipyridinium TQ (-0.54 V vs. NHE) as a mediator, nitrogenase catalysis resulted in remarkably more products. The UV-vis and in situ potentiometric studies revealed that better performance with TQ is achieved due to the significantly more negative solution potential allowing for efficient reduction of FeP. As a result, the quantum yield for conversion of absorbed photons to ammonia attains 16%, far exceeding that of previously reported nitrogenase-based systems. This work reveals the importance of tuning the electron transfer pathways in photocatalytic systems and illustrates a potent strategy for efficient electronic coupling of a photosensitizer and an N 2 reduction catalyst.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Identification of In Situ Generated High-Spin Fe(II)-N 4 Active Sites for Acidic Oxygen Reduction Reaction via Operando 57 Fe Mössbauer Spectroscopy

Iron-nitrogen-carbon (FeNC) catalysts are considered among the most promising alternative to Pt catalysts in acidic oxygen reduction reaction (ORR), yet the geometric and electronic structures of the true active site under reaction conditions have not been clearly elucidated. Herein, we synthesized a representative FeNC catalyst by pyrolyzing Fe 3+ absorbed on ZIF-8-derived N-doped carbon at a mild temperature under the H 2 /Ar atmosphere, where a formation mechanism of FeN 4 sites through a Zn-mediated Fe nanoparticle atomization process was proposed. The resulting FeNC-750 catalyst shows high acidic ORR activity with a half-wave potential of 0.838 V and a peak power density of 1 W cm -2 in proton-exchange membrane fuel cell (PEMFC). By using operando 57 Fe Mössbauer spectroscopy on FeNC-750, it was revealed that the pyrrolic N-coordinated high-spin Fe 2+ N 4 sites, which are in situ generated from high-spin Fe 3+ N 4 during ORR, are identified as catalytic active states. Density functional theory calculations further verified that, compared to the pyridinic N-coordinated low-spin Fe 2+ N 4 , the pyrrolic N-coordinated high-spin Fe 2+ exhibits optimized adsorption energy for reaction intermediates, thereby lowering the energy barrier of the rate-determining step (RDS) and facilitating OH* desorption. In conclusion, this work provides both experimental and theoretical evidence of the true active site in the FeNC during acidic ORR, offering significant insights for the rational design of high-performance materials for acidic fuel cells.

FeNC catalyst↗
DOE OSTI2021

Topical Report – Findings on Subtask 2.7 – Wet ESP and Aerosol Testing at Coal Creek Station

Growing concerns over the impact of CO 2 emissions from combustion sources on global climate change have prompted numerous research and development projects aimed at developing cost-effective technologies for CO 2 capture. One family of technologies being demonstrated at pilot and full scale globally is postcombustion carbon capture (PCCC) systems that employ amine-based solvents. The captured CO 2 can be compressed and permanently stored underground or used for enhanced oil recovery. The proximity of North Dakota’s lignite-fired fleet of power plants to potential CO 2 storage options creates a unique atmosphere for PCCC within the state. However, the unique components present in lignite flue gas present a challenge for large-scale PCCC at North Dakota power plants by contributing to aerosol formation. Aerosols can negatively impact the long-term performance of amine-based solvents for CO 2 capture. Amine-based solvents are volatile, and flue gas particulate provides nucleation sites where amine vapors can condense as aerosols. Because aerosols cannot be easily captured at the column outlet using conventional technologies, the amine-laden aerosols escape the system and lead to accelerated solvent losses. Moreover, particulate components can chemically react with amines to form degradation products that can permanently deactivate the amine, cause fouling, and lead to hazardous emissions. Many of the elements that have been shown to catalyze solvent degradation are present in lignite coals and can exacerbate solvent replacement economics. Understanding this issue is critical to the implementation of solvent-based CO 2 capture systems as applied to lignite-fired generation systems. The Energy & Environmental Research Center (EERC) designed and carried out this project to fully characterize aerosol behavior with various control technologies installed to better optimize aerosol mitigation technology for CO 2 capture. To meet the goal of this project, the following objectives were identified: Determine the effectiveness of a wet electrostatic precipitator (WESP) on mitigating formation of problematic aerosols at Great River Energy’s Coal Creek Station, upstream of the PCCC system. Determine the effectiveness of the Mitsubishi Heavy Industries (MHI) proprietary amine emission reduction unit (AERU) as a postcapture solvent recovery system for reducing aerosol emissions and extending solvent life downstream of the PCCC system. Determine the impact of aerosols on the efficiency and degradation products of both commercial and advanced solvents within the PCCC system. Work was conducted at Coal Creek Station Unit 1 using a slipstream of flue gas from the outlet of the plant’s flue gas desulfurization (FGD) unit. Flue gas was routed through a pilot-scale FGD unit to remove SO 2 to very low levels (~1 ppm) and then through a direct contact cooler (DCC) to further cool the gas and to remove moisture. The gas exiting the DCC was then optionally routed through a WESP before passing to the CO 2 absorber columns. The MHI solvent was used to scrub CO 2 from the slipstream through a set of two absorber columns. The rich solvent was regenerated in a stripper column by heating to drive off captured CO 2 . Flue gas exiting the absorber column was routed to MHI’s proprietary AERU to recover entrained solvent. The system operated using a catch-and-release method where the CO 2 was separated to provide data on the process, but the captured CO 2 was released back into the host site stack. Particulate was measured, collected, and analyzed from multiple locations throughout the pilot-scale system. Unlike the performance observed in prior work, the inlet FGD and DCC did not remove significant particulate matter from the flue gas. This appears to be due to a difference in the nature of the particulate. The DCC seemed to increase particulate size and count, most likely owing to water condensing onto the surfaces of fly ash particles. When the WESP was operated, it achieved >95% particulate capture. Very little particulate matter or indications of solvent were detected at the AERU outlet. When operating with advanced KS 21 solvent, the particulate material at the AERU outlet was even further decreased. Solvent analysis showed that some species derived from flue gas and ash were slowly concentrating in the solvent over the duration of the test. The levels observed were reported to be within expected ranges and were not of concern to MHI. A high-level techno-economic assessment of installing CO 2 capture at Coal Creek Station suggested that, when using a standard monoethanolamine (MEA)-based solution with simple heat integration, the energy penalty to net generation would be 34%. The bulk of this was due to steam losses for regenerating solvent, followed by parasitic electrical demand for CO 2 compression and then by increased parasitic load for pushing flue gas through the absorber column. These demands could be decreased with a more advanced solvent that exhibits lower heat of regeneration and lower pressure drop than does a simple MEA solution. Further energy could be saved with more thorough heat integration to recover useful energy from the steam used for solvent regeneration. Installing a WESP was predicted to increase the cost of electricity by nearly $5/MWh. This would become cost-effective if solvent losses were roughly 10 times the baseline estimate when not using a WESP but could be returned to baseline by installing the WESP. Piping CO 2 for storage in more favorable geology could help with carbon capture and storage economics. Although storing off-site would necessitate construction of a CO 2 transport pipeline, the cost of this pipeline might be more than offset by reducing the number of wells required, the depths of the wells required, and the electrical demand for the CO 2 compressor. Additional factors that favor off-site storage costs include smaller expected CO 2 plume sizes, which translates to less monitoring and fewer landowner agreements. More detailed assessment of the specific geology in the region under and around Coal Creek Station would be needed to accurately assess the costs and benefits of different storage site options. This subtask was cofunded through the Energy & Environmental Research Center–U.S. Department of Energy Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission.

Strege, Joshua↗
DOE OSTI2025

Band Gap Engineering and Metastable Phase Discovery in Cu 2 BaSnS 4– x Se x Nanocrystals via Topotactic Anion Exchange

Earth-abundant multinary inorganic chalcogenides, such as Cu 2 BaSnS 4–x Se x (CBTSSe), have emerged as promising absorbers for next-generation solar cells. However, accessing colloidal CBTSSe nanocrystals, including metastable polymorphs with more favorable optoelectronic properties, remains a critical synthetic challenge. Herein, we report the first use of topotactic anion exchange to access metastable crystal structures in soft chemistry syntheses. By varying the stoichiometry of selenium precursors, we directly synthesize Cu 2 BaSnS 4–x Se x (0 ≤ x ≤ 4) nanocrystals with a broad band gap tunability of 1.51–2.04 eV. At x = 4, a new metastable trigonal phase of Cu 2 BaSnSe 4 is isolated. This phase arises via an in-situ topotactic anion exchange from sulfur-rich Cu 2 BaSnS 4–x Se x intermediates, while retaining both the cation sublattice and overall nanocrystal morphology. The trigonal Cu 2 BaSnSe 4 exhibits a nearly direct band gap that is 280 meV lower than its thermodynamically stable orthorhombic counterpart, aligning more closely with the optimal band gap for single-junction solar cells. In contrast, a post-synthetic anion exchange route leads to the thermodynamically preferred orthorhombic polymorph, pointing to the critical nature of the in-situ transformation. Our findings open a versatile pathway for both polymorphic and morphological control in colloidal nanocrystals, expanding the synthetic design space for new optoelectronic materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Characterization of the degradation of gamma-irradiated elastomers using Raman spectroscopy

This report presents key findings from Raman spectroscopic analysis of gamma-irradiated rubber samples extracted from a laminated lead-damped rubber (LDR) seismic isolation device. The samples were exposed to gamma radiation from a 60Co source in a Foss Therapy Services gamma irradiator, reaching absorbed doses up to 1600 kGy. A distinct threshold near 400 kGy was identified, beyond which significant spectral changes were observed. Two Raman peaks - at approximately 425 cm-1 and 2440 cm-1 - were tracked as a function of dose using Gaussian fitting. The 425 cm-1 peak, attributed to sulfur–sulfur (S–S) bond stretching (resulting from vulcanization of the rubber), exhibited a dose-dependent upshift, indicating radiation-induced crosslinking within the sulfur-based polymer network. Conversely, the 2440 cm-1 peak, likely associated with vibrational modes of additives or impurities, showed a downward shift with increasing dose, suggesting chain scission and degradation of non-rubber constituents. These results provide first-of-a-kind insights into the microstructural evolution of elastomers under high-dose gamma irradiation and establish a preliminary dose threshold for significant degradation. Future work will incorporate multi-modal characterization—including Fourier Transform Infrared (FTIR) spectroscopy, scanning electrom microscopy (SEM) of the rubber surface morphology, thermogravimetric analysis (TGA) to determine changes in thermal stability, and mechanical testing—to correlate molecular-level changes with macroscopic performance of these elastomers as damping media in seismic isolation devices. These findings are expected to provide regulatory guidance and design criteria for qualifying low-damping rubber seismic isolators in advanced nuclear reactor applications.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

Assessment of Existing Transportation Packages for Use with HALEU

Commercial light water reactor operators and fuel vendors in the United States are pursuing changes to fuel that include increased 235 U enrichment. Economic studies generally anticipate maximum near-term fuel assembly designs with up to 8 wt.% 235 U. Many next-generation nuclear reactor designs require high-assay low-enriched uranium (HALEU) (19.75 wt.% > 235 U > 5 wt.%) fuel. One necessary element for the commercial-scale use of HALEU is the ability to safely transport large quantities of enriched fuel material in multiple forms. However, there is uncertainty as to whether subcriticality requirements can be satisfied with existing package designs and whether existing critical benchmark experiment data are sufficient to support criticality safety code validation for HALEU transportation applications. This study assesses the potential to use currently licensed transportation packages for the transportation of increased enrichment unirradiated U fuel forms. The assessment uses selected package designs that represent the five categories of fuel form-boiling water reactor pins and assemblies, pressurized water reactor pins and assemblies, UF 6 , U-metal and tristructural isotropic (TRISO) particles, and UO 2 pellets or powder-and focuses on demonstrating subcriticality and identifying benchmark critical experiments appropriate for use in criticality computer code validation. Key quantities of interest that relate to subcriticality are limiting conditions (e.g., optimum moderation), package or package array k eff , package capacity, and package transportation array size. The SCALE TSUNAMI-3D and TSUNAMI Indices and Parameters codes are used for sensitivity and uncertainty calculations and for identification of candidate critical benchmark experiments for code validation. The primary metric for identifying candidate benchmarks is the similarity coefficient, c k . For each fuel form category, a representative package is evaluated. Results provided for each package evaluation include enrichment and packaging limits (e.g., maximum transportation array size as a function of enrichment) and benchmark critical experiment similarity coefficients. Results indicate that there are viable means for increasing enrichments into the HALEU range across the spectrum of fuel forms with differing increase amounts available for different packages. Sources of subcriticality margin to offset increased enrichment reactivity include reduced transportation array size, reduced fissile mass, burnable absorber credit, and safety analysis margin harvesting. For all packages except the DN-30, numerous critical benchmark experiment candidates for validation were identified.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

A Combined Computer Vision and Deep Learning Approach for Rapid Drone-Based Optical Characterization of Parabolic Troughs

Optical accuracy is a primary driver of parabolic trough concentrating solar power (CSP) plant performance, but can be damaged by wind loads, gravity, error during installation, and regular plant operation. Collecting and analyzing optical measurements over an entire operating parabolic trough plant is difficult, given the large scale of typical installations. Distant Observer, a software tool developed at the National Renewable Energy Laboratory, uses images of the absorber tube reflected in the collector mirror to measure both surface slope in the parabolic mirror and offset of the absorber tube from the ideal focal point. This technology has been adapted for fast data collection using low-cost commercial drones, but until recently still required substantial human labor to process large amounts of data. A new method leveraging advanced deep learning and computer vision tools can drastically reduce the time required to process images. This new method addresses the primary analysis bottleneck, identifying featureless, reflective mirror corner points to a high degree of accuracy. Recent work has shown promising results using computer vision methods. The combined deep learning and computer vision approach presented here proved highly effective and has the potential to further automate data collection and analysis, making the tool more robust. The method presented in this paper automatically identified 74.3% of mirror corners within 2 pixels of their manually marked counterparts and 91.9% within 3 pixels. This level of accuracy is sufficient for practical Distant Observer analysis within a target uncertainty. A commercial drone collected video of over 100 parabolic trough modules at an operating CSP plant to demonstrate the deep learning and computer vision method's usefulness in processing large amounts of data. These troughs were successfully analyzed using Distant Observer, paired with the new deep learning and computer vision algorithm, and can provide plant operators and trough designers with valuable insight about plant performance, operating strategies, and plant-wide optical error trends.

computer vision↗
DOE OSTI2021

Design principles of tandem cascade photoelectrochemical devices

Cascade photoelectrocatalysis (PEC) is a possible method to improve the selectivity of solar-driven CO 2 reduction (CO 2 R). This concept can be realized by coupling different CO 2 R catalysts to different subcells in a multijunction photovoltaic (PV) stack. Efficient implementation will require careful tuning of the photocurrents and design of the photovoltages provided by the subcells to the CO 2 R catalysts in such a way as to facilitate the target reaction. Here, we outline the design principles of the tandem PEC approach using two-step conversion of CO 2 to ethylene in aqueous electrolyte, via a CO intermediate, as a model system. To perform this reaction, the first coupled PV-catalyst component should provide 4 electrons to reduce 2 molecules of CO 2 to CO; the second component should provide 8 electrons to reduce 2 CO molecules to C 2 H 4 . Based on known CO 2 R catalysts, the overpotential required to produce CO can be less than that required to reduce it to ethylene, creating the opportunity for improved efficiency. Cascade PEC can be realized in a three-terminal tandem (3TT) configuration using III–V-semiconductor based subcells coupled to Au (produces CO intermediate) and Cu (converts CO to ethylene). The current to each catalyst can be controlled by the area of the subcell exposed to the electrolyte, and the photovoltage is determined by the materials selected and device configuration. Operating conditions are found by simulating the coupled system using the open-source circuit simulator SPICE (Simulation Program with Integrated Circuits Emphasis). We identify conditions under which a 3TT configuration can have a higher solar to chemical conversion efficiency compared to a two-terminal two-junction tandem (2T 2J) with the same absorbers and a Cu catalyst only. We also show that 3TT PEC devices can be less sensitive to variations in catalyst activity compared to 2T devices. Lastly, we discuss the applications of cascade PEC to CO 2 reduction, using different intermediates, and to other chemical networks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Development of an Attenuated Total Reflectance–Ultraviolet–Visible Probe for the Online Monitoring of Dark Solutions

Optical spectroscopy is a valuable tool for on-line monitoring of a variety of processes. Ultraviolet-visible (UV-vis) spectroscopy in particular, can monitor the concentration of analytes as well as identify speciation and oxidation state. However, it can be difficult to impossible to employ UV-vis based sensors on chemical systems that are very dark (i.e., high optical density) as exceedingly short pathlengths are required (for transmission approaches) or effective means of backscattering are needed (for reflectance approaches). Examples of processes that would benefit significantly from the use of optical sensors and encounter these challenges include used nuclear fuel recycling and molten salts with high concentrations of dissolved uranium. Utilizing an attenuated total reflectance (ATR) UV-vis approach can overcome these challenges and allow for the measurement of solutions orders of magnitude more concentrated than transmission UV-vis. However, determining ideal sensor specifications for varied processes can be time consuming and expensive. Here, in this study, we evaluate the ability for a novel ATR-UV-vis probe to measure very concentrated solutions of Co(II) and Ni(II) nitrate as well as organic dyes (methylene blue, acid red 1, and crystal violet). This sensor design provides a modular method for exploring possible “pathlengths” by altering the exposed ATR fiber length. Also studied were approaches to loading and measuring the sensor cell. These results are compared to a traditional 1 cm cuvette measured by transmission UV-vis. It was found that the ATR-UV-vis probe was capable of measuring solutions 600 times more concentrated than the 1 cm cuvette. Advanced data analysis in the form of multivariate curve resolution (MCR) was used to analyze the speciation of methylene blue over a large concentration range. The application of this novel ATR-UV-vis probe to the interrogation of dark solutions is a promising avenue for use in on-line monitoring of nuclear processes.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Progress report on analytic and numerical studies of x-ray-induced impulse

In a variety of high-energy-density (HED) systems, x-rays of a given energy are used to generate shockwaves, bulk motion, and impulse in materials. As radiation energy is deposited within the material, the material is heated. The number of photons of a certain wavelength absorbed is determined by the spectral intensity of the radiation and the material’s opacity evaluated at that wavelength. This heating results in a pressure increase dictated by the material’s equation of state. Depending on the intensity of the absorbed radiation, it may also cause the material to change phase into a liquid, gas, or plasma. The increased pressure drives the heated surface layer to blow off, imparting impulse and sending a compressive wave into the bulk of the material. Additionally, the compression wave interacts with the solid boundary of the material, resulting in a tensile wave that may cause the material to spall. The impulse generated by the deposition of x-ray energy within the sample can be modeled using purely analytical methods, e.g. the Bethe, Bade, Averell, and Yost (BBAY) model. However, the blow-off process is rather complicated, and proper modeling efforts must account for material ejected by spallation, vaporization, jetting, and plasma ablation. For this reason, analytical models have an unclosed term describing the final energy of the blown-off material Ef(z). Prior modeling efforts have arbitrarily fixed this at some value or modeled it using a limiting set of thermodynamic assumptions. The work we are currently performing uses validated simulations using sophisticated photon transport, equation of state, and strength models/data to provide a fit for Ef(z) that is useful for predictive calculation of impulse. We will apply our methodology and show results for different materials and x-ray sources. This work is particularly useful for the design of experiments studying x-ray impulse generation. The present report is outlined as follows. Section 1.2 describes a series of HED experiments investigating x-ray-generated impulse in materials. Section 1.3 describes the computational approach we employ in this study, and presents validation results against the aforementioned experiments. Section 1.4 introduces analytical models for impulse generation, as well as our method for utilizing impulse from simulations to close the models. We discuss the concept of impulse-spectrum sensitivity, it’s application to uncertainty quantification, and derive a very useful analytical expression for it in 1.5. We then summarize recent progress in this project and discuss future work in section 1.6.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The impact of helium on plasma-driven hydrogen permeation and implications for direct internal recycling in the fusion fuel cycle

Abstract Metal foil pumps (MFPs) are the leading technology for direct internal recycling (DIR) of hydrogen isotopes from the plasma exhaust in future fusion plants. MFPs rely on the concept of superpermeation, where superthermal H atoms directly absorb into the metal foil, rapidly diffuse, and desorb downstream. To date, studies of superpermeation have predominantly employed either pure hydrogen or in some cases trace levels of impurities. The plasma exhaust is expected to contain just ∼1% helium, but in DIR the source gas would be enriched in helium as hydrogen isotopes are extracted. In this work, we explore the impact of helium on hydrogen superpermeation at low temperature (75 °C–200 °C) using Pd-based foils. To first order, the flux scaled linearly with the hydrogen mole fraction. Stable permeation was observed until the helium fraction reached ∼80%, where the flux began to decline slowly with time. In addition, short term (1–5 min) exposure to pure helium plasma significantly attenuated subsequent hydrogen plasma permeation, and the degree was more dramatic at elevated temperature. This attenuation was correlated with He retention in the foils, which was detected by time-of-flight secondary ion mass spectrometry at low levels (<0.1 at. %) and limited to the near surface (<10 nm). Similar trends were observed among all alloys (Pd, PdAg, PdCu), and the foils were restored to full performance with an Ar + sputter clean. The potential for helium plasma exposure to impact MFP performance under these conditions has not been previously reported, and these findings have significant implications to the design and implementation of practical DIR systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Business Opportunities in Clean Energy Supply Chains: Guidebook for Small and Medium-Sized Automotive Suppliers

This is the final report for the referenced TCF award which ran from Oct. 2019 through Jan. 2024 in conjunction with the industry partner Swift Solar. The long duration of the program was due to several factors including the pandemic and a technical work stoppage due to changes in the scope. Additionally, Swift’s business focus shifted during the course of the program. As a result of these factors, this program underwent two distinct modifications that dramatically changed the work scope. The following report is organized into three separate sections, each of which addresses a distinct work scope. Those scope changes, what necessitated them, and any new tasks/milestones are given, briefly, at the top of each section. The work performed was research on the hybrid halide perovskites (HHP), both the absorber material itself as well as other material layers that are required in a full device stack. At the start of the period of performance, there were two distinct challenges that we sought to address: (1) a wide band gap absorber (>1.6 eV), and (2) a recombination layer for tandem devices that provided good sequestration of the individual cell absorber materials in their respective device layers. NREL had previously published, and patented, advancements in both of these areas and they were the focus of much of the work throughout the program. The auto manufacturing space is evolving quickly. Sales of various electrified vehicles (xEVs) continue to grow steadily, which has medium to long-term ramifications for the thousands of U.S. manufacturers and hundreds of thousands of workers that contribute to the domestic automotive supply chain. In tandem with this growth in xEV sales, domestic clean energy manufacturing is surging (both for the xEV supply chain and other technologies), with public incentives spurring billions in private sector investment. Moreover, the next 2–3 years will see new and expanded industrial facilities come online to make products like hydrogen electrolyzers, solar panels, batteries, advanced electronics—and will create new supply chain needs and business opportunities as they do. DOE’s Office of Manufacturing and Energy Supply Chains (MESC) and Argonne National Laboratory developed this report to help automotive manufacturers—alongside various business support partners— understand these trends and their response options, and to make the most of current federal assistance programs for manufacturers. These market changes may create opportunities for small- and medium-sized manufacturers (SMMs) to expand production, grow profit margins, and diversify their businesses. For instance, SMMs could take advantage of engineering and process design similarities with new end-use industries that might enable greater business growth and stability as markets continue to change.

14 SOLAR ENERGY↗
DOE OSTI2021

Electronic Structure and Excited-State Dynamics of Rylene–Tetrapyrrole Panchromatic Absorbers

Panchromatic absorbers have potential applications in molecular-based energy-conversion schemes. A prior porphyrin–perylene dyad (P-PMI, where “MI” denotes monoimide) coupled via an ethyne linker exhibits panchromatic absorption (350–700 nm) and a tetrapyrrole-like lowest singlet excited state with a relatively long singlet excited-state lifetime (τ S ) and increased fluorescence quantum yield (Φ f ) versus the parent porphyrin. To explore the extension of panchromaticity to longer wavelengths, three arrays have been synthesized: a chlorin–terrylene dyad (C-TMI), a bacteriochlorin–terrylene dyad (B-TMI), and a perylene–porphyrin–terrylene triad (PMI-P-TMI), where the terrylene, a π-extended homologue of perylene, is attached via an ethyne linker. Characterization of the spectra (absorption and fluorescence), excited-state properties (lifetime, yields, and rate constants of decay pathways), and molecular-orbital characteristics reveals unexpected subtleties. The wavelength of the red-region absorption band increases in the order C-TMI (705 nm) < PMI-P-TMI (749 nm) < B-TMI (774 nm), yet each array exhibits diminished Φ f and shortened τ S values. The PMI-P-TMI triad in toluene exhibits Φ f = 0.038 and τ S = 139 ps versus the all-perylene triad (PMI-P-PMI) for which Φ f = 0.26 and τ S = 2000 ps. The results highlight design constraints for auxiliary pigments with tetrapyrroles to achieve panchromatic absorption with retention of viable excited-state properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Dynamic characterization and performance evaluation of a 10-kW power take-off with mechanical motion rectifier for wave energy conversion

The power take-off (PTO) is a key component for wave energy converters. In this paper, a compact PTO with mechanical motion rectification rated at 10 kW is designed and prototyped, and characterized. A piecewise nonlinear dynamic model is established to describe its unique dynamic property. A linear hydraulic actuator is adopted in lab testing to drive the prototype and the unknown parameters of the dynamic model are identified. Further verification shows that the model can predict the dynamic performance of the PTO well. The test results show that the mechanical motion rectifier-based PTO can achieve overall energy transfer efficiency as high as 65% in regular waves even when the generator is working below the rated electric load and speed. In the irregular wave test, the PTO achieved the overall energy transfer efficiency of 54%, and the peak-to-average ratio acquired during the test is 12.5.

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Using personal monitoring data to derive organ doses for medical radiation workers in the Million Person Study—considerations regarding NCRP Commentary no. 30

The study of low dose and low-dose rate exposure is of central importance in understanding the possible range of health effects from prolonged exposures to radiation. The One Million Person Study of Radiation Workers and Veterans (MPS) of low-dose health effects was designed to evaluate radiation risks among healthy American workers and veterans. The MPS is evaluating low-dose and dose-rate effects, intakes of radioactive elements, cancer and non-cancer outcomes, as well as differences in risks between women and men. Medical radiation workers make up a large group of individuals occupationally exposed to low doses of radiation from external x-ray/gamma exposures. For the MPS, about 100 000 United States medical radiation workers have been selected for study. The approach to the complex dosimetry circumstances for such workers over three to four decades of occupation were initially and broadly described in National Council on Radiation Protection and Measurements (NCRP) Report No. 178. NCRP Commentary No. 30 provides more detail and describes an optimum approach for using personal monitoring data to estimate lung and other organ doses applicable to the cohort and provides specific precautions/considerations applicable to the dosimetry of medical radiation worker organ doses for use in epidemiologic studies. The use of protective aprons creates dosimetric complexity. It is recommended that dose values from dosimeters worn over a protective apron be reduced by a factor of 20 for estimating mean organ doses to tissues located in the torso and that 15% of the marrow should be assumed to remain unshielded for exposure scenarios when aprons are worn. Conversion coefficients relating personal dose equivalent, H p (10) in mSv, to mean absorbed doses to organs and tissues, D T in mGy, for females and males for six exposure scenarios have been determined and presented for use in the MPS. This Memorandum summarises several key points in NCRP Commentary No. 30.

Environmental Sciences & Ecology↗
DOE OSTI2021

Next Generation Cuprous Phenanthroline MLCT Photosensitizer Featuring Cyclohexyl Substituents

A new long–lived, visible light–absorbing homoleptic Cu(I) metal–to–ligand charge transfer (MLCT) photosensitizer [Cu(dchtmp) 2 ]PF 6 (dchtmp = 2,9–dicyclohexyl–3,4,7,8–tetramethyl–1,10–phenanthroline), has been synthesized, structurally characterized, and evaluated in terms of its molecular photophysics, electrochemistry, and electronic structure. Static and time–resolved transient absorption (TA) and photoluminescence (PL) spectroscopy measured on the title compound in CH 2 Cl 2 (τ = 2.6 μs, Φ PL = 5.5%), CH 3 CN (τ = 1.5 μs, Φ PL = 2.6%), and THF (τ = 2.0 μs, Φ PL = 3.7%) yielded impressive photophysical metrics even when dissolved in Lewis basic solvents. The combined static spectroscopic data along with ultrafast TA experiments revealed that the pseudo–Jahn–Teller distortion and intersystem crossing dynamics in the MLCT excited state displayed characteristics of being sterically arrested throughout its evolution. Here, electrochemical and static PL data illustrate that [Cu(dchtmp) 2 ]PF 6 is a potent photoreductant (–1.77 V vs. Fc +/o in CH 3 CN) equal to or greater than all previously investigated homoleptic Cu(I) diimine complexes. Although we successfully prepared the cyclopentyl analog dcptmp (2,9–dicyclopentyl–3,4,7,8–tetramethyl–1,10–phenanthroline) using the same C–C radical coupling photochemistry as dchtmp, the corresponding Cu(I) complex could not be isolated due to the steric hinderance presented at the metal center. Ultimately, the successful preparation of [Cu(dchtmp) 2 ] + represents a major step forward for the design and discovery of novel earth–abundant photosensitizers made possible through a newly conceived ligand synthetic strategy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗