Search NASA⌕ Search

SEARCH · Search NASA

Results for “COPRECIPITATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Thermoluminescence characteristics of LiF: Cu nanocrystalline phosphor

Copper (Cu) activated LiF phosphor in nanocrystalline form has been prepared by the chemical co-precipitation method for radiation dosimetry application. The formation of nanocrystalline structure has been confirmed by X-ray diffraction and Scanning electron microscopy. Cubical shaped nanostructure with average particle size of 33nm has been formed. The sample was prepared at different concentration of Cu from 0.01mol% to 3 mol%. TL properties were investigated by studying the glow curve after irradiating the phosphor to gamma ray Co{sup 60} source with dose of 15 Gy. It has been found that nanocrystalline LiF: Cu show simple glow curve structure with a single glow peak at 404 K where as commercially available phosphors exhibits multi peak complex glow curve structure. The effect of different normality on the TL properties of phosphor has been studied. Maximum TL intensity for LiF: Cu (0.1mol %) phosphor is observed at the normality of 0.5N and annealing temperature of 200°C. The phosphor showed good linearity up to 10 KGy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Erbium induced magnetic properties of Er/ZnO nanoparticles

Pure and Er (2, 3 and 4 at. %) doped ZnO nanoparticles have been synthesized by chemical co-precipitation method. EDS spectrum confirmed the presence of Zn, O and Er in the synthesized samples. The XRD measurements confirmed the hexagonal wurtzite structure of ZnO for all samples. The crystallite size of the samples decreases with increase in concentration and are compatible with the results that obtained from TEM analysis.EPR spectra exhibitedferromagnetic signals the substitution Er The possible ferromagnetic zinc interstials signal is appeared for 2 at. % of Er dopant. The room temperature ferromagnetic is observed only for 2 at. % of Er while all other samples exhibiting weak ferromagnetic nature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Structural, magnetic and electrical properties of samarium substituted multiferroic bismuth ferrite

Polycrystalline Bi{sub 0.8}Sm{sub 0.2}FeO{sub 3} was synthesized by a simple co – precipitation route. Single phase of the prepared sample was confirmed by X-ray diffraction analysis which further reveals that it crystalizes as mixed crystal structure of rhombohedral with R3c space group and orthorhombic with Pnma space group. A considerable increase in magnetization was observed at room temperature VSM analysis and temperature dependent dielectric analysis shows an anomaly at the vicinity of Neel temperature (T{sub N}). Room temperature ferroelectric study explicitly authenticates the formation of a better loop due to the reduced leakage current and the suppression of oxygen deficiencies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of pH on particles size and gas sensing properties of In{sub 2}O{sub 3} nanoparticles

In this work, indium oxide (In{sub 2}O{sub 3}) nanoparticles have been synthesized by co-precipitation method and the effect of pH on the structural and sensor response values of In{sub 2}O{sub 3} nanoparticles has been reported. X-ray diffraction pattern (XRD) revealed the formation of cubic phase In{sub 2}O{sub 3} nanoparticles. FESEM results indicate the formation of nearly spherical shape In{sub 2}O{sub 3} nanoparticles. The band gap energy value changed with change in pH value and found to have highest value at pH 9. Indium oxide nanoparticles thus prepared were deposited as thick films on alumina substrates to act as gas sensors and their sensing response to ethanol vapors and LPG at 50 ppm was investigated at different operating temperatures. It has been observed that all sensors exhibited optimum response at 300°C towards ethanol and at 400°C towards LPG. In{sub 2}O{sub 3} nanoparticles prepared at pH 9, being smallest in size as compared to other, exhibit highest sensor response (SR).

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Viscosity studies of water based magnetite nanofluids

Magnetite nanofluids of various concentrations have been synthesized through co-precipitation method. The structural and topographical studies made with the X-Ray Diffractometer and Atomic Force Microscope are presented in this paper. The density and viscosity studies for the ferrofluids of various concentrations have been made at room temperature. The experimental viscosities are compared with theoretical values obtained from Einstein, Batchelor and Wang models. An attempt to modify the Rosensweig model is made and the modified Rosensweig equation is reported. In addition, new empirical correlation is also proposed for predicting viscosity of ferrofluid at various concentrations.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Synthesis and characterization of nanocomposite polymer blend electrolyte thin films by spin-coating method

Solid Polymer blend electrolytes based on Polyethylene oxide (PEO) and poly vinyl pyrrolidone (PVP) complexed with zinc oxide nanoparticles (ZnO NPs; Synthesized by Co-precipitation method) thin films have prepared at a different weight percent using the spin-coating method. The complexation of the NPs with the polymer blend was confirmed by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR). The variation in film morphology was examined by polarized optical micrographs (POMs). The thermal behavior of blends was investigated under non-isothermal conditions by differential thermal analyses (DTA). A single glass transition temperature for each blend was observed, which supports the existence of compatibility of such system. The obtained results represent that the ternary based thin films are prominent materials for battery and optoelectronic device applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Study of magneto-optic effect on Mn{sub 1-x}Zn{sub x}Fe{sub 2}O{sub 4} nanoferrofluids

Mn{sub 1-x}Zn{sub x}Fe{sub 2}O{sub 4} nanoparticles (with x varying as 0.1, 0.3, 0.5, 0.7 and 0.9) have been synthesized by co- precipitation method using polyvinyl alcohol as surfactant. Structural analysis and surface morphology of the samples were analysed using X-ray diffraction and scanning electron microscope respectively. The Scherer approximation was used to obtain crystallite sizes and found to decrease from 8.9 nm to 4.3 nm with increase in zinc substitution. The chemical composition of samples obtained through EDAX was comparable with the initial substitutions. Saturation magnetization (M{sub s}), Remanence (M{sub r}) and Coercivity (H{sub c}) were measured using VSM at room temperature and found to decrease with increase in zinc substitution. Verdet constant of the samples are obtained from Faraday rotation for various magnetic fields and it varies from 18 × 10{sup −4} to 3 × 10{sup −4}deg/Gcm with zinc substitution.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Structural and magnetic properties of Prussian blue analogue molecular magnet Fe{sub 1.5}[Cr(CN){sub 6}]·mH{sub 2}O

Molecular magnets, based on Prussian blue analogues, Fe{sub 1.5}[Cr(CN){sub 6}]·mH{sub 2}O have been synthesized in the bulk as well as nanoparticle forms using a co-precipitation method, and their structural and magnetic properties have been investigated using x-ray diffraction (XRD) Mössbauer spectroscopy and dc magnetization. The XRD study confirms the single phase crystalline and nanoparticle nature of the compounds with a face centered cubic (fcc) structure of space group Fm3m. The values of lattice constant are found to be ~10.18(5) Å and ~9.98(9)Å, for the bulk and nanoparticle samples, respectively. The dc magnetization shows a Curie temperature (T{sub C}) of ~17 K and ~5 K for the bulk and nanopartcile samples, respectively. The Mossouber spectroscopy reveal that the compound shows spin flipping from the high spin (HS) Fe (Cr{sup III}–C≡N–Fe{sup II}) to low spin (LS) Fe{sup II} ions (Cr{sup III}–N≡C–Fe{sup II}). Moreover, the T{sub C} and the HS state of the Fe ions decreases (converts to its LS states) with time as well as in the nanoparticle form compared to bulk.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Cation distribution in CuFe{sub 2}O{sub 4} nanoparticles: Effects of Ni doping on magnetic properties

The Cu{sub 1−x}Ni{sub x}Fe{sub 2}O{sub 4} nanoparticles (with x = 0, 0.3, 0.5, 0.7, and 1) were synthesized by using spray co-precipitation method at annealing temperature T{sub a} = 900 °C in air for 5 h. The crystal structure, microstructure, oxidation state, and magnetic properties of the samples were characterized by using X-ray diffraction, synchrotron X-ray diffraction, scanning electron microscopy, X-ray absorption spectroscopy, and vibrating sample magnetometer. It was shown that all the samples have cubic structure. Lattice constant and grain size decrease, while the Curie temperature T{sub C} increases with increasing of Ni{sup 2+} content. A small amount of Fe{sup 2+} was found in all the samples. Cation distribution was determined by using a combination of magnetization measurements, extended X-ray absorption fine structure analysis, and Rietveld refinement from synchrotron X-ray diffraction data. It was indicated that Ni{sup 2+} ions occupy in octahedral site only, while Cu{sup 2+} ions distribute in both tetrahedral and octahedral sites. The variation of magnetic parameters is discussed based on Ni{sup 2+} concentration, grain size, the cation distribution, surface effect, and the presence of Fe{sup 2+} ion in the samples.

36 MATERIALS SCIENCE↗

Nanopowders M{sub 2}O{sub 3} (M = Y, La, Yb, Nd) with spherical particles and laser ceramics based on them

We have considered the problems of agglomeration of yttrium aluminium garnet (YAG) nanopowders prepared by chemical co-precipitation of precursors from aqueous solutions and subsequent calcination. To fabricate YAG and Y{sub 2}O{sub 3} laser ceramic samples with high optical transmittance and reproducible characteristics, we have developed a method for producing non-agglomerated nanopowders of pure and doped Y{sub 2}O{sub 3} by homogeneous chemical precipitation. Nanopowders Y{sub 2}O{sub 3} with La and Yb as well as mixtures of Y{sub 2}O{sub 3} : Nd and several commercial nanopowders of aluminium oxide have been compacted; optimised compacting technique have been selected; ceramic samples (Y, La, Yb){sub 2}O{sub 3} and YAG : Nd with high optical transmittance at a wavelength of 1 {mu}m have been produced by solid-phase synthesis. (extreme light fields and their applications)

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

REPORT ON QUALITATIVE VALIDATION EXPERIMENTS USING LITHIUM-ALUMINUM LAYERED DOUBLE-HYDROXIDES FOR THE REDUCTION OF ALUMINUM FROM THE WASTE TREATMENT PLANT FEEDSTOCK

A process for removing aluminum from tank waste simulants by adding lithium and precipitating Li-Al-dihydroxide (Lithiumhydrotalcite, [LiAl{sub 2}(OH){sub 6}]{sup +}X{sup -}) has been verified. The tests involved a double-shell tank (DST) simulant and a single-shell tank (SST) simulant. In the case of the DST simulant, the product was the anticipated Li-hydrotalcite. For the SST simulant, the product formed was primarily Li-phosphate. However, adding excess Li to the solution did result in the formation of traces of Li-hydrotalcite. The Li-hydrotalcite from the DST supernate was an easily filterable solid. After four water washes the filter cake was a fluffy white material made of < 100 {micro}m particles made of smaller spheres. These spheres are agglomerates of {approx} 5 {micro}m diameter platelets with < 1 {micro}m thickness. Chemical and mineralogical analyses of the filtrate, filter cake, and wash waters indicate a removal of 90+ wt% of the dissolved Al for the DST simulant. For the SST simulant, the main competing reaction to the formation of lithium hydrotalcite appears to be the formation of lithium phosphate. In case of the DST simulant, phosphorus co-precipitated with the hydrotalcite. This would imply the added benefit of the removal of phosphorus along with aluminum in the pre-treatment part of the waste treatment and immobilization plant (WTP). For this endeavor to be successful, a serious effort toward process parameter optimization is necessary. Among the major issues to be addressed are the dependency of the reaction yield on the solution chemistry, as well as residence times, temperatures, and an understanding of particle growth.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Final report for grant number DE-FG02-06ER64244 to the University of Idaho (RW Smith)-coupling between flow and precipitation in heterogeneous subsurface environments and effects on contaminant fate and transport

Engineered remediation strategies for inducing mineral precipitation in the subsurface typically involve the introduction of at least one reactant either by direct injection or by in situ generation. The localization of reactant sources means a wide range of saturation states and ion ratios will be created as reactants are mixed: These conditions together can result in a wide range of precipitation rates, as well as impact which mineral phase precipitates. This is potentially important for the capacity of the precipitates to take up of trace metal contaminants, for their long term stability. Aragonite, for example, is able to sequester a larger amount of Sr than calcite. However, aragonite is less stable under typical groundwater conditions, and so may release sequestered Sr over time as the aragonite transforms to a more stable phase. In addition, previous experimental studies have indicated that other system constituents may influence calcium carbonate precipitation and consequently the Sr uptake potential of a system. For example, dissolved organic carbon (at levels typical of groundwaters) can suppress crystal growth. As a result, the continuous nucleation of small crystals, rather than growth of existing crystals, may be the dominant mode of precipitation. This has the potential for greater uptake of Sr because the smaller crystal sizes associated with nucleated calcite may more readily accommodate the distortion resulting from substitution of the larger Sr ion for Ca ions than can larger crystals. However, these smaller crystals may also be less stable and over the long term release Sr as a result of Ostwald ripening. To better understand the formation and composition of relevant calcium carbonate mineral phases two related series of mineral precipitation experiments were conducted. The first series of experiments, conducted using a Continuously Stirred Tank Reactor (CSTR) operated at steady state rates of precipitation was focused on understanding the influence of pH and ammonium carbonate (the hydrolysis product of urea: ureolytically driven calcium carbonate precipitation has been demonstrated to be a promising method of inducing mineral precipitation in the field) on calcium carbonate polymorph and Sr co-precipitation. The second series of experiments, conducted at constant pH and saturation state, was focused on understanding the influence of aqueous carbonate to calcium ratios on the precipitation rate of calcite. In 12 CSTR experiments (three pH levels, two ammonium carbonate levels, and two strontium levels) we found that lower pH values and ammonium carbonate concentration promoted the precipitation of calcite and the higher pH values and ammonium carbonate concentration promoted the precipitation of aragonite (as determined by X-ray diffraction). Overall, the rate of calcium carbonate precipitation increased with increasing pH and ammonium carbonate concentration, consistent with increasing values of Q/K. Intermediate conditions resulted in the precipitation of a mixture of calcite and aragonite. There was no discernible effect of strontium on the rate of precipitation or the phase precipitated. In our experiments we precipitated rhombohedral calcite, lath-shaped aragonite and inter-grown calcite-aragonite mixtures. Using Laser Ablation-Inductively Coupled Plasma-Mass Spectrometer we characterized the composition of solids from an experiment in which both calcite and aragonite precipitates were identified by X-ray diffraction. We found a range in composition from a high Sr and low Mg phase (inferred to be aragonite) to a coexisting lower Sr and higher but variable Mg phase (inferred to be calcite). Values of the distribution coefficient for strontium of 1.1 and 0.2 for aragonite and calcite, respectively were estimated from the data. These values compare to values of 1.1 and 0.1 for aragonite and calcite, respectively, determined from bulk analysis of precipitates from experiments in which only calcite or only aragonite were detected. In our experiments to assess the influence of solution composition on precipitation rate (at a constant value of Q/K), we found that the precipitation rate varied by approximately a factor of 2 over the range of conditions considered, with a maximum rate observed at a carbonate to calcium ion molar ratio of approximately 0.2. Precipitation kinetics at the extremes tested in this study exhibited interesting behavior. At the lowest ion ratio (carbonate to calcium ion molar ratio of 0.004), a metastable solution was not achievable. At the highest ion ratio (carbonate to calcium ion molar ratio of 4), the solution was indefinitely metastable: no amount of seed material added initiated a drop in pH that would indicate the onset of precipitation. Under conditions considered to date, we cannot definitively quantify the influence (if any) of Sr at 0.1 mM on the measured precipitation rates (work continues in this area through the INL SFA).

54 ENVIRONMENTAL SCIENCES↗

Oxalate co-precipitation synthesis of calcium zirconate and calcium titanate powders.

Fine powders of calcium zirconate (CaZrO{sub 3}, CZ) and calcium titanate (CaTiO{sub 3}, CT) were synthesized using a nonaqueous oxalate co-precipitation route from Ca(NO{sub 3}){sub 2}{center_dot}4 H{sub 2}O and group(IV) n-butoxides (Ti(OBu{sup n}){sub 4} or Zr(OBu{sup n}){sub 4}). Several reaction conditions and batch sizes (2-35 g) were explored to determine their influence on final particle size, morphology, and phase. Characterization of the as-prepared oxalate precursors, oven dried oxalate precursors (60-90 C), and calcined powders (635-900 C) were analyzed with TGA/DTA, XRD, TEM, and SEM. Densification and sintering studies on pressed CZ pellets at 1375 and 1400 C were also performed. Through the developed oxalate co-precipitation route, densification temperatures for CZ were lowered by 125 C from the 1500 C firing temperature required for conventional mixed oxide powders. Low field electrical tests of the CZ pellets indicated excellent dielectric properties with dielectric constants of {approx}30 and a dissipation factor of 0.0004 were measured at 1 kHz.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Inducing Mineral Precipitation in Groundwater by Addition of Phosphate

Induced precipitation of phosphate minerals to scavenge trace metals and radionuclides from groundwater is a potential remediation approach for contaminated aquifers. Phosphate minerals can sequester trace elements by primary mineral formation, solid solution formation and/or adsorption, and they are poorly soluble under many environmental conditions, making them attractive for long-term sustainable remediation. The success of such engineered schemes will depend on the particular mineral phases generated, their rates of formation, and their long term stability. The purpose of this study was to examine the precipitation of calcium phosphate minerals under conditions representative of a natural groundwater. Because microorganisms are present in groundwater, and because some proposed schemes for induced phosphate mineral precipitation rely on the stimulation of native groundwater populations, we also tested the effect of bacterial cells (initial densities of 105 and 107 ml-1) within the precipitation medium. We also tested the effect of a trace mixture of propionic, isovaleric, formic and butyric acids (total concentration 0.035 mM). The experiments showed that the general progression of mineral precipitation was similar under all of the conditions, with initial formation of amorphous calcium carbonate, and transformation to poorly crystalline hydroxyapatite (HAP) by the end of the week-long experiments. The presence of the bacterial cells appeared to delay precipitation, although by the end of 7 days the overall extent of precipitation was similar for all of the treatments. The stoichiometry of the final precipitates as well as results of Rietveld refinement of x-ray diffraction data indicated that the treatments including organic acids and bacterial cells resulted in increased distortion of the HAP crystal lattice, with the higher concentration of cells resulting in the greatest distortion. Uptake of Sr into the phosphate minerals was decreased in the treatments with cells and organic acids, compared to the control. The results of the experiments enable a greater understanding of the challenges associated with phosphate-based remediation schemes for contaminated environments.

54 ENVIRONMENTAL SCIENCES↗

High capacitive performance of nanostructured Mn-Ni-Co oxide composites for supercapacitor

Nanostructured Mn-Ni-Co oxide composites (MNCO) were prepared by thermal decomposition of the precursor obtained by chemical co-precipitation of Mn, Ni and Co salts. The chemical composition and morphology were characterized by X-ray diffraction (XRD), energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM). The electrochemical capacitance of MNCO electrode was examined by cyclic voltammetry, impedance and galvanostatic charge-discharge measurements. The results showed that MNCO electrode exhibited the good electrochemical characteristics. A maximum capacitance value of 1260 F g{sup -1} could be obtained within the potential range of -0.1 to 0.4 V versus saturated calomel electrode (SCE) in 6 mol L{sup -1} KOH electrolyte.

36 MATERIALS SCIENCE↗

Preparation of Sm-doped ceria (SDC) nanowires and tubes by gas-liquid co-precipitation at room temperature

Sm-doped cerium dioxide (SDC) with fcc structure was formed using a gas-liquid chemical co-precipitation process at room temperature. Morphology and structure of the as-prepared samples were characterized using TG, XRD, TEM, HRTEM and SAED techniques. Under our specific experimental conditions, two kinds of 1D nano-structures SDC have been mainly obtained. SDC nanowires are 0.3-1.2 {mu}m in lengths and 5-20 nm in diameters. SDC nanotubes have outer diameters in 10-40 nm with lengths up to 2 {mu}m. The as-prepared SDC shows very strong UV absorption ability and the maximum absorption peak redshifts compared with that of SDC nanoparticles.

36 MATERIALS SCIENCE↗

Effect of dispersant on preparation of barium-strontium titanate powders through oxalate co-precipitation method

The quantitative precipitation of barium-strontium titanyl oxalate: (Ba{sub 0.6}Sr{sub 0.4}TiO(C{sub 2}O{sub 4}){sub 2}.4H{sub 2}O, BSTO) precursor powders were successfully prepared through oxalate co-precipitation method. The pyrolysis of BSTO at 800 deg. C/4 h produced the barium-strontium titanate (Ba{sub 0.6}Sr{sub 0.4}TiO{sub 3}, BST) powders. Two kinds of dispersants namely ammonium salt of poly mathacrylic acid (PMAA-NH{sub 4}) and polyethylene glycol (PEG) were added respectively during the co-precipitation procedure. The powders were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), etc. Experimental results show that the addition of the dispersants reduced the productive rate of BST powders. The BSTO and BST powders obtained by aforementioned technique without dispersants were homogeneous with quasi-orbicular morphology. The particles grew into spindle shape with the effect of PEG. The morphology homogeneity was broke with small grains as well as large agglomerated particles concurrent when PMAA-NH{sub 4} was added. The mechanism of the effect of the two dispersants was investigated in detail.

36 MATERIALS SCIENCE↗

Synthesis and photocatalytic performances of BiVO{sub 4} by ammonia co-precipitation process

This paper reports the preparation and photocatalytic performance of Bismuth vanadate (BiVO{sub 4}) by a facile and inexpensive approach. An amorphous BiVO{sub 4} was first prepared by a co-precipitation process from aqueous solutions of Bi(NO{sub 3}){sub 3} and NH{sub 4}VO{sub 3} using ammonia. Followed by heating treatment at various temperatures, the amorphous phase converted to crystalline BiVO{sub 4} with a structure between monoclinic and tetragonal scheelite. The crystallization of BiVO{sub 4} occurred at about 523 K, while the nanocrystalline BiVO{sub 4} were formed with a heat-treatment of lower than 673 K. However, when the heat-treatment was carried out at 773 K, the accumulation of nanocrystals to bulk particles was observed. The photocatalytic performances of the materials were investigated by O{sub 2} evolution under visible-light, and MB decomposition under solar simulator. The results demonstrated that the crystalline structure is still the vital factor for the activities of both reactions. However, the crystallinity of BiVO{sub 4} gives a major influence on the activity of O{sub 2} evolution, whereas the surface area, plays an important role for photocatalytic MB decomposition. - Abstract: BiVO{sub 4} was prepared by a co-precipitation process using aqueous ammonia solution, followed by heating treatment at various temperatures. The crystalline structure and crystallization process, and their influences on photocatalytic O{sub 2} evolution and organic pollutants degradation were investigated. It demonstrated that the crystalline structure is still the vital factor for the activities of both reactions. However, the crystallinity of BiVO{sub 4} gives a major influence on the activity of O{sub 2} evolution, whereas the surface area, plays an important role for photocatalytic MB decomposition. Display Omitted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗