Search NASA⌕ Search

SEARCH · Search NASA

Results for “CORROSIVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Open-air plasma-assisted deposition of organosilicon coating for corrosion protection of AZ91D Mg alloy

As a corrosion barrier layer, open-air plasma-assisted organosilicon coating was applied on AZ91D Mg alloy. Organosilicon-coated AZ91D samples, prepared from two different plasma coating processes, were used for corrosion evaluation based on multistep electrochemical and H 2 collection measurements in 3.5 wt% sodium chloride (NaCl) solution. Some coated AZ91D samples were characterized with and without corrosion exposure in NaCl solution using electron microscopies and X-ray chemical analysis techniques. Further, the results indicate that the organosilicon coatings from open-air plasma processes are effective to delay the initiation of corrosion attack and also reduce the corrosion rate for AZ91D substrate. The corrosion attack was considered to develop after permeation of NaCl solution through the coating layer.

36 MATERIALS SCIENCE↗

Effect of neutron and ion irradiation on the metal matrix and oxide corrosion layer on Zr-1.0Nb cladding alloys

A detailed study has been carried out on recrystallised Zr-1.0Nb alloys corroded and irradiated under different conditions, including ex-autoclave and ex-reactor samples. After 540 days in reactor and damage around 5 dpa, the neutron irradiated sample shows no serious evidence for radiation enhanced corrosion and is still in pre-transition stage. The good corrosion resistance of the neutron irradiated Zr-1.0Nb can be related to the higher volume fraction of tetragonal phase and fewer interconnected nano porosity/cracks in the oxide. This indicates less tetragonal to monoclinic transition, leads to more protective oxide in the neutron irradiated sample, containing little evidence for short circuit paths for the penetration of oxygen or water towards the metal-oxide interface. These observations on a sample with a slow overall oxidation rate are consistent with the hypothesis that interconnected porosity can lead to early transitions and rapid oxidation. Tetragonal oxide can be either stabilised by irradiation, or stabilised by local release of impurity species from SPPs such as dissolution of Fe from Zr-Nb-Fe precipitates or radiation introduced precipitates (RIPs) which is likely to be small β-Nb clusters. The oxide consists of well-aligned columnar-equiaxed microstructure in the autoclave sample while a more complex oxide grain structure was observed in the neutron-irradiated sample. As oxide continues to grow, there are more < a > and < c > loops, dissolved Fe and RIPs in the metal matrix, however, the corrosion rate is low enough for the tetragonal oxide to stabilise and suboxide + Zr(Osat) phases exist for protectiveness, so there is no enhanced corrosion after radiation. In situ ion irradiation in the TEM revealed no visible defect clusters or voids in the oxide, suggesting that radiation damage to the metal matrix rather than oxide may have a stronger effect on corrosion mechanisms after neutron irradiation, however, cascade damages are not visible in this case. Neutron irradiation also seems to have little effect on promoting fast oxidation or dissolution of β-Nb precipitates into the surrounding oxide or metal during irradiation. Furthermore, these results are discussed in the light of the current mechanisms for corrosion of nuclear fuel cladding alloys.

(S)TEM↗

Origins of wear-induced tungsten corrosion defects in semiconductor manufacturing during tungsten chemical mechanical polishing

During chemical mechanical polishing (CMP) process optimization, a unique corrosion defect was identified in the tungsten (W) contact plugs, which were investigated to develop practical solutions to improve CMP mass productivity. The corrosion defect occurred in the absence of external incident energy and was observed to occur only at the W plugs connected to the P + /n-well close to the wafer edge. To examine the root cause of the corrosion, a series of experiments was carried out at each W CMP step, using in-line defect inspection. Additional experiments were conducted using on-line inductively coupled plasma mass spectrometry (ICP-MS) to understand pH- and potential-dependent electrochemical dissolution behaviors of W. Experimentally, W corrosion was confirmed to be exacerbated if the surface oxide of the W plugs is removed by the deionized water (DIW) rinsing step under wafer pressurization, then exposed to DIW and alkaline cleaning solution. Although the DIW rinsing step is commonly performed to clean polishing pads right after the main polishing, a small amount of applied pressure (0.5 psi) without slurry supply can lead to corrosion defects. Finally, this wear-induced corrosion of the W plugs can be prevented by removing the applied pressure during the post DIW rinsing step of W CMP.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Approaches to investigate the role of chelation in the corrosivity of biomass-derived oils

The need to provide the U.S. market with a renewable liquid fuel energy source from a non-food feedstock stream has gained considerable traction due to benefits such as improved energy efficiency, reduced environmental impacts, and enhanced national security. Practical achievement of these goals via biomass and bio-waste utilization involves production of liquid intermediates containing corrosive, reactive species like carboxylic acids, ketones, aldehydes, and hydroxyaldehydes. Such mixtures challenge materials of containment, processing, and transport. It is widely recognized that the smaller organic acids, such as acetic and formic, are corrosive and can remove protective surface oxides on alloys used in bio-oil processing infrastructure, and ketones can swell sealing polymers. However, literature shows, and findings herein confirm, larger carboxylic acids and bidentate alcohols are present. This highlights the potential for synergistic, detrimental effects of constituents in bio-oil corrosion, including direct reactivity of small acids compounded with the possibility of mobilization of protective metal oxide layers via chelation by larger acids and oxygenates. The question of whether species beyond small acids can significantly contribute to corrosion requires analytical approaches previously not applied to bio-oil corrosion studies and certainly not previously applied corroboratively. As such, this work introduces a combination of optical, mass spectral, and electrochemical impedance spectroscopies with an incubation approach to study metal mobilization, to facilitate elucidating chelation's role in bio-oil corrosive pathways. To enable systematic study of these oxygenates' material compatibility individually and in combination, a model matrix of bio-oil constituents was also developed based on identification of key components of real bio-oils.

09 BIOMASS FUELS↗

Self-healing, re-adhering, and carbon-steel corrosion mitigating properties of fly ash-containing calcium aluminum phosphate cement composite at 300 °C hydrothermal temperature

This study assesses here the ability of calcium aluminate phosphate (CAP)/fly ash F (FAF) blend composite to self-heal at early age; to re-adhere to the casing surfaces after debonding and to protect carbon steel (CS) against brine-caused corrosion before and after the re-adherence. The composite was damaged after autoclaving for 24 h at 300 °C and then exposed to the same conditions for 5 more days for the self-healing and re-adhering processes. The ability of the blend to self-heal and re-adhere to CS was evaluated 1) by measurements of the recovery of compressive and bond strengths and Young's modulus; 2) by performing the 3-dimensional micro-image analysis of sealed cracks; 3) by phase identification in composite matrix and in the cracks after the healing; 4) by measurements of CS corrosion impediment by the re-adhered composite after 300°C-5-day restoration period. After the healing, the two factors, sealing effect of cracks by reaction products and change in phase composition of cement matrix, essentially governed the recovery of the original mechanical strength. For the former, analcime phase derived from pozzolanic FAF autogenous healing aid played the major role in sealing the cracks, while the well-formed hydroxyapatite phase contributed to the latter factor. The lap-shear bond with the strength of 1.11 MPa at CS plate/composite adhesive/CS plate joint failed cohesively, showing higher bond strength than strength of the composite matrix. The rebonded composite-CS plates developed a 0.37 MPa bond strength after the 5-day restoration period. The results of electrochemical polarization corrosion tests revealed that the re-adhered composite covering CS plate significantly inhibited the brine-caused corrosion of CS, leading to 0.011 mm/year corrosion rate, corresponding to 50% reduction compared with that of before re-adhering. There were two factors governing such corrosion mitigation: enhanced adhesive contact of composite with CS and increased coverage by the re-adhering composite.

36 MATERIALS SCIENCE↗

Chloride induced reinforcement corrosion behavior in self-healing concrete with encapsulated polyurethane

Cracks in reinforced concrete structures accelerate the ingress of chlorides and therefore cause a higher risk for corrosion. In this research, autonomous healing of cracks by encapsulated polyurethane was investigated as a possible method to reduce reinforcement corrosion. Reinforced concrete beams were exposed weekly to a chloride solution and electrochemical parameters were measured to determine the influence of the self-healing mechanism on the corrosion process. The rebars were visually examined afterwards. For the cracked beams an active state of corrosion was detected within an exposure period of 10 weeks and clear pitting corrosion was observed on the rebars. Autonomous crack healing with low viscosity polyurethane could significantly reduce the corrosion in the propagation stage. For these specimens no visual damage to the rebars was detected. In conclusion, the application of self-healing concrete with a low viscosity polyurethane is able to enhance the durability of reinforced concrete structures in marine environments.

36 MATERIALS SCIENCE↗

Fractal coatings of Ni and NiYSZ for high-temperature corrosion mitigation in solar salt

This paper introduces a novel approach to corrosion mitigation using electrodeposited, fractal Ni and NiYSZ coatings. Highly adherent, durable multiscale coatings with fractal dimensions above 1.80 were fabricated. Corrosion characteristics of coated plain and etched surfaces of In800H, SS310, SS316 and SS347, in comparison to Ha230, were studied in molten 60% NaNO 3 + 40% KNO 3 at 600 °C. The corrosion rate of coated Fe-based alloys reduced by up to 68% compared to uncoated alloys and was on par with or lower than the corrosion rate of Ha230. Furthermore, the corrosion-resistant coatings provide for use of low-cost alloys in high temperature corrosive environments.

36 MATERIALS SCIENCE↗

Discovering the nanoscale origins of localized corrosion in additive manufactured stainless steel 316L by liquid cell transmission electron microscopy

Here, we use liquid cell scanning transmission electron microscopy (STEM) to directly characterize the nanoscale origins of corrosion initiation in Additive manufacturing (AM) 316 L stainless steel. Under applied anodic potentials, we found that the dislocation cellular boundaries were preferentially corroded and that regions of localize corrosion occurred along the cellular boundaries. We directly observed the earliest stages of corrosion by controlling the biasing parameters to decelerate the corrosion processes. The results show that highly localized corrosion occurs via inclusion dissolution along dislocation cell boundaries. More widespread corrosion initiates at the dislocation cell boundaries and spreads throughout the dislocation networks.

36 MATERIALS SCIENCE↗

Mechanistic transition of stainless steel 304L corrosion in MgCl 2 phase change material under thermal cycling

Magnesium chloride (MgCl 2 )-based molten salt phase change materials (PCMs) are promising candidates for thermal energy storage (TES) owing to their advantageous thermophysical properties, however, their high corrosivity in the molten state limits material compatibility. In this study, the corrosion behavior of 304?L stainless steel (SS304L) exposed to MgCl2 PCM was investigated as a function of thermal cycling (up to 9000 cycles) relevant to PCM-based TES systems. Microstructural changes and elemental redistribution at the alloy-salt interface under thermal cycling conditions were characterized using synchrotron-based X-ray fluorescence (XRF) and scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDS). Results show that corrosion is governed by selective Cr-dissolution and elemental diffusion near the interface and grain boundaries. A clear transition in the dominant corrosion mechanism is observed with increasing thermal cycles. Surface corrosion is the dominant mechanism up to 1000 cycles, whereas intergranular corrosion becomes the primary degradation mode beyond 2000 cycles. These mechanistic changes are interpreted in terms of evolving interfacial chemistry, microstructure and the diffusion-driven redistribution of alloying elements.

36 MATERIALS SCIENCE↗

Microbeam synchrotron radiation diffraction and fluorescence of oxide layers formed on zirconium alloys at different corrosion temperatures

Autoclave corrosion tests of Zircaloy-4 were performed at temperatures ranging from 274°C to 427 °C to determine how the characteristics of the oxide layer changed with corrosion temperature. Corroded samples were prepared in cross-section and examined at the Advanced Photon Source using x-ray diffraction and fluorescence with sub-micron spatial resolution. These measurements provide high fidelity data for characterization of the oxide layer grown on zirconium alloys over a range of temperatures to better understand the fundamental mechanisms of corrosion. It was found that the size of the monoclinic oxide grains increases with distance from the metal-oxide interface, while the average grain size of the tetragonal oxide phase decreases. This is consistent with the continuous nucleation of a mixture of equiaxed tetragonal and monoclinic grains at the metal-oxide interface, of which only the monoclinic oxide grains that are properly aligned to minimize stresses grow into long columnar oxide grains. The tetragonal phase oxide grains transform to monoclinic oxide once a critical size is reached. While the monoclinic oxide grain size increases with corrosion temperature, the tetragonal phase grain size remains below a maximum value. Evolution of the tetragonal fraction, calculated with the Garvie-Nicholson formula, was observed, with local maxima seen just before transition and local minima seen at oxide locations corresponding to the oxide kinetic transition. No difference was observed in the tetragonal phase fraction in the oxide layers formed at different corrosion temperatures. Detailed fluorescence and diffraction mapping of one sample showed the evolution of the diffraction intensity over a short range in the oxide. In conclusion, this work provides a systematic study revealing fundamental characteristics of the microstructure of Zircaloy-4 oxide layers to further understanding of corrosion resistance of these materials.

36 MATERIALS SCIENCE↗

First steps toward predicting corrosion behavior of structural materials in molten salts

To address the need for physics-based models to predict corrosion behavior of materials in molten salts, here we propose potential methods to aid in selection of optimum materials for structural components in molten salt powered technologies. In the present work, the role of alloy thermodynamics and kinetics on governing corrosion rates of Ni-based alloys will be discussed combining experimental and computational methods. A few strategies are presented to quantify corrosion rates of Ni-based materials isothermally exposed in purified KCl-MgCl 2 salts at 600° C-800° C. The influence of capsule material, potential corrosion products and role of alloy composition on the observed corrosion rates was discussed with coupled thermodynamic-kinetic models. Larger depths of corrosion attack were observed in alloy 230 specimens compared to other alloys under similar conditions was attributed to the much higher chemical activity of Cr in the alloy that results in a larger Cr chemical potential gradient.

36 MATERIALS SCIENCE↗

Two new supramolecular metal diphosphonates: Synthesis, characterization, crystal structure and inhibiting effects on metallic corrosion

Two new divalent metal(II) aminodiphosphonates with layered structure, namely, Cu(H{sub 3}L{sup 1}){sub 2}·2H{sub 2}O (1), [H4L{sup 1}=methyl-N(CH{sub 2}PO{sub 3}H{sub 2}){sub 2}] and Cd{sub 2}(H{sub 2}L{sup 2}){sub 4}(2), [H{sub 4}L{sup 2}=n-propyl-N(CH{sub 2}PO{sub 3}H{sub 2}){sub 2}] were synthesized and characterized. The Cu(II) ions in complex 1 are octahedrally coordinated by four oxygen atoms from two chelating ligands and two phosphonate oxygen atoms from two neighboring Cu(H{sub 3}L{sup 1}){sub 2} units. The Cu(H{sub 3}L{sup 1}){sub 2} units are interconnected by bridging phosphonate groups, forming a 2-D metal phosphonate layer. The structure of complex 2 contains two unique Cd(II) ions octahedrally-coordinated by six phosphonate oxygen atoms from four H{sub 2}L{sup 2} diphosphonate anions. Corrosion inhibition performances of 1 and 2 were also compared with each other in order to study the effect of combinations of externally added Cd/H{sub 4}L{sup 2} and Cu/H{sub 4}L{sup 1} (1:1 ratio) on corrosion rates of carbon steel. It was found that at pH 3.0, Cd/H{sub 4}L{sup 2} or Cu/H{sub 4}L{sup 1} combinations do not have noticeable corrosion inhibition efficiency for carbon steel. In contrast, at pH 7.0, higher corrosion inhibition efficiency was achieved for Cd/H{sub 4}L{sup 2}. Physical characterizations such as scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS) and Fourier transform infrared spectroscopy (FTIR) were applied to study the corrosion specimens and film material. - Graphical abstract: Two new metal phosphonates have been synthesized and characterized by single-crystal X-ray diffraction and thermogravimetric analysis. corrosion inhibition performances 1 and 2 are also compared.

36 MATERIALS SCIENCE↗

Influence of alloying element Zn on the microstructural, mechanical and corrosion properties of binary Mg-Zn alloys after severe plastic deformation

Highlights: • Mg-Zn alloys are processed by equal channel angular pressing with back-pressure. • The α-Mg matrix consists of highly deformed and partially recrystallized areas. • Zn concentration varies in the α-Mg matrix by up to 2 at.%. • The alloys exhibit mechanical anisotropy and a significant increase in strength. • Equal channel angular pressing increases corrosion rate of Mg-Zn alloys. - Abstract: This work presents an analysis of the microstructural, mechanical and corrosion properties of two binary Mg-Zn alloys. Mg-6 wt%Zn and Mg-12 wt%Zn cast alloys were subjected to annealing followed by quenching and processed via equal channel angular pressing with applied back-pressure (ECAP-BP). After ECAP-BP, both alloys were thoroughly examined and showed partially recrystallized and highly deformed areas. High-angle annular dark-field imaging revealed a difference in Zn content across the α-Mg matrix of the Mg-12 wt%Zn after ECAP-BP due to the growth of MgZn{sub 2} nanoparticles. Electron energy-loss spectroscopy (EELS) was carried out to qualify an average Zn content in these areas, and a variation in Zn content up to 2 at.% was found. Compression tests revealed mechanical anisotropy and a significant increase in the strength of both alloys after ECAP-BP. The yield strength, σ{sub 02}, was in the range from 269 to 385 MPa depending on the composition and compression axis. The initial state alloys showed yield strengths, σ{sub 02}, of only 75–150 MPa but improved ductility. The corrosion rates of the Mg-Zn alloys in the initial state, evaluated using a hydrogen evolution method in NaCl solution, were higher for Mg-12 wt%Zn. The corrosion rates of both alloys after ECAP-BP were higher than those of the initial state. Light microscopy observations did not reveal any preference for corrosion propagation, including transcrystalline, intercrystalline or interphase corrosion, in any of the materials.

36 MATERIALS SCIENCE↗

Corrosion of Ferrous Structural Alloys in Biomass Derived Fuels and Organic Acids

This work investigated the corrosivity of biomass-derived liquid fuels and organic acids associated with bio-oils and conducted a corrosion compatibility evaluation of several structural ferrous alloys in the fuels and acids. Here, the acidity parameters and solution conductivity values were higher in raw pyrolysis bio-oils than postprocessed oils with significant corrosion attack for carbon steel and Fe-2.25Cr-1Mo. However, higher-grade stainless steels, ferritic Fe-15Cr (15Cb) and austenitic types 304L and 316L, showed negligible corrosion loss, whereas lower-Cr ferritic grades 409, 410, and 416 were attacked. Metal leaching tests and electrochemical impedance spectroscopy measurements revealed superior corrosion resistance of 316 over 410 stainless steels in solutions of formic and oxalic acids that can be present in bio-oils. The corrosion evaluation methods utilized in this work provide effective screening tools to identify the compatible structural alloys for bio-oils.

09 BIOMASS FUELS↗

Use of Carbon Steel for Construction of Post-combustion CO 2 Capture Facilities: A Pilot-Scale Corrosion Study

Corrosion studies were carried out on metal coated and noncoated carbon steel as well as stainless steel in a pilot-scale post-combustion CO 2 capture process. Aqueous 30 wt % monoethanolamine (MEA) solvent was used without any chemical additive for antioxidation to examine a worst-case scenario where corrosion is not mitigated. The corrosion rate of all carbon steels was almost zero in the absorber column and CO 2 lean amine piping except for Ni-coated carbon steel (<1.8 mm/yr). Ni 2 Al 3 /Al 2 O 3 precoated carbon steels showed initial protection but lost their integrity in the stripping column and CO 2 rich amine piping, and severe corrosion was eventually observed for all carbon steels at these two locations. Stainless steel was found to be stable and corrosion resistant in all of the sampling locations throughout the experiment. This study provides an initial framework for the use of carbon steel as a potential construction material for process units with relatively mild operating conditions (temperature less than 80 °C), such as the absorber and CO 2 lean amine piping of a post-combustion CO 2 capture process. As a result, it also warrants further investigation of using carbon steel with more effective corrosion mitigation strategies for process units where harsh environments are expected (such as temperatures greater than 100 °C).

36 MATERIALS SCIENCE↗

One dimensional wormhole corrosion in metals

Corrosion is a ubiquitous failure mode of materials. Often, the progression of localized corrosion is accompanied by the evolution of porosity in materials previously reported to be either three-dimensional or two-dimensional. However, using new tools and analysis techniques, we have realized that a more localized form of corrosion, which we call 1D wormhole corrosion, has previously been miscategorized in some situations. Using electron tomography, we show multiple examples of this 1D and percolating morphology. To understand the origin of this mechanism in a Ni-Cr alloy corroded by molten salt, we combined energy-filtered four-dimensional scanning transmission electron microscopy and ab initio density functional theory calculations to develop a vacancy mapping method with nanometer-resolution, identifying a remarkably high vacancy concentration in the diffusion-induced grain boundary migration zone, up to 100 times the equilibrium value at the melting point. Deciphering the origins of 1D corrosion is an important step towards designing structural materials with enhanced corrosion resistance.

36 MATERIALS SCIENCE↗

Directly monitoring the shift in corrosion mechanisms of a model FeCrNi alloy driven by electric potential

Abstract Stainless steels are used in a myriad of engineering applications, including construction, automobiles, and nuclear reactors. Developing accurate, predictive mechanistic models for corrosion and electrochemical corrosion kinetics of stainless steels has been a topic of research studies over many decades. Herein, we quantified the aqueous corrosion kinetics of a model austenitic Fe–18Cr–14Ni (wt%) alloy in the presence and absence of applied potential using systematic in situ electrochemical atomic force microscopy (EC-AFM) and transmission electron microscopy (TEM). Without an applied bias, vertical dissolution of corrosion pits is controlled by the surface kinetics/diffusion hybrid mechanism, whereas lateral dissolution is diffusion controlled. When an electric bias is applied, the increase in corrosion rate is dominated by the nucleation of new pits. These insights gained by the in situ EC-AFM will allow applications of this method for a quantitative understanding of corrosion of a wider class of materials.

36 MATERIALS SCIENCE↗

The Effect of Corrosion on the Seismic Behavior of Buried Pipelines and a Remedy for Their Seismic Retrofit

The effect of corrosion phenomenon has been investigated by performing some sets of 3-Dimensional Nonlinear Time History Analysis (3-D NLTHA) in which soil structure interaction as well as wave propagation effects have been taken into consideration. The 3-D NLTHA has been performed by using a finite element computer program, and both states of overall and local corrosions have been considered for the study. The corrosion has been modeled in the computer program by introducing decreased values of either pipe wall thickness or modulus of elasticity and Poisson ratio. Three sets of 3-component accelerograms have been used in analyses, and some appropriate numbers of zeros have been added at the beginning of records to take into account the wave propagation in soil and its multi-support excitation effect. The soil has been modeled by nonlinear springs in longitudinal, lateral, and vertical directions. A relatively long segment of the pipeline has been considered for the study and the effect of end conditions has been investigated by assuming different kinds end supports for the segment. After studying the corroded pipeline, a remedy has been considered for the seismic retrofit of corroded pipe by using a kind of Fiber Reinforced Polymers (FRP) cover. The analyses have been repeated for the retrofitted pipeline to realize the adequacy of FRP cover. Numerical results show that if the length of the pipeline segment is large enough, comparing to the wave length of shear wave in the soil, the end conditions do not have any major effect on the maximum stress and strain values in the pipe. Results also show that corrosion can lead to the increase in plastic strain values in the pipe up to 4 times in the case of overall corrosion and up to 20 times in the case of local corrosion. The satisfactory effect of using FRP cover is also shown by the analyses results, which confirm the decrease of strain values to 1/3.

58 GEOSCIENCES↗