Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Cladding Degradation Model

This report begins with an evaluation of cladding degradation mechanisms deemed important to assessing barrier capability. Unlike similar efforts done in the past, this evaluation accounts for the hypothetical conditions associated with direct dual-purpose canister (DPC) disposal, including conditions resulting from a postulated, in-package, steady-state criticality event. A total of 16 cladding degradation mechanisms are examined assuming direct disposal of DPCs in two different hypothetical repositories: a saturated repository in shale and an unsaturated repository in alluvium.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Report summarizing demonstration of thermal conductivity measurement methods for coated zirconium cladding

Thermal diffusivity measurements on Zirconium-based cladding materials have historically been a challenge due to the difficulty to measure on specimens with curved geometries, including nuclear grade Zircaloy cladding materials. In this work, we first used Laser Flash Analysis methods to measure the thermal diffusivity of Zircaloy tubes, which show good agreement with Zircaloy plates in this work, as well as previously published data. The consistent results proved the applicability of the Laser Flash Analysis setup for investigating thermal diffusivity of Zircaloy tubes. We further investigate the hydrogen effect on thermal diffusivity of Zircaloy tubes. Hydrogen plays significant roles in temperature dependent thermal diffusivity trends of Zircaloy tube. For low hydrogen concentration, where hydride dissolved into single phase α-Zr at higher temperature, thermal diffusivity is relatively unchanged at low temperature at two phase regions (α-Zr and δ-hydride), and it increases as a function of temperature at single phase α-Zr region. For high hydrogen concentration, where phase transformation (α-Zr + δ-hydride → α-Zr + β-Zr) occurs at 567 °C, thermal diffusivity decreases as a function of temperature below 567 °C before the transformation (α-Zr and δ-hydride), while increase at higher temperature after the transformation (α-Zr and β-Zr).

36 MATERIALS SCIENCE↗

BISON Validation to In-Situ Cladding Burst Test and High Burnup LOCA Experiments

The process to develop and qualify nuclear fuels for commercial nuclear application requires fundamental material development, characterization, and design; out-of-pile testing on unirradiated materials; integral fuel rod irradiations, testing, and post irradiation examinations (PIEs); and transient analyses. The historical approach depends on the generation of large empirical datasets and series of integral fuel rod irradiations, and this approach ultimately takes approximately 20 years—or sometimes longer—to acquire data through extensive sequential testing. Thus, the qualification and eventual deployment of new fuel systems constitute a long and drawn-out process. However, recent technological advancements have provided researchers the opportunity to perform out-of-cell, in-situ measurements to assess material performance for the duration of the experiment. One such example of this capability is the use of digital image coordination and thermal imaging to assess Zircaloy cladding performance under a simulated loss-of-coolant accident (LOCA) transient condition. In general, the in-situ measurements provide high-fidelity strain, strain rates, and temperature surface maps. This is critical for the United States nuclear industry, which is actively developing a technical basis to support extending the peak rod average burnup from 62 to ~75 GWd/tU and the deployment of accident-tolerant fuel. However, the Nuclear Regulatory Commission, through their research information letter, outlined a number of technical issues for the industry to address before extending burnup. One topic of specific interest is understanding the cladding balloon and rupture geometry during the LOCA heatup phase. Leveraging these advanced in-situ capabilities, this work intends to use insitu data generated from a simulated LOCA in the Severe Accident Test Station at Oak Ridge National Laboratory to better understand high-temperature creep and its impact on Zircaloy balloon and rupture performance. This work used the BISON fuel performance code to compare BISON’s high-temperature creep model predictions to in-situ data and identify limitations and gaps within the model. Additionally, BISON will subsequently be used to simulate relevant high-burnup LOCA tests. The results will be analyzed and compared to the available post-test data in a manner consistent with the approach outlined in the Nuclear Regulatory Commission research information letter.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Review and Summary of Oxide Thickness Data for Aluminum-Clad Spent Nuclear Fuel

The U.S. Department of Energy (DOE) owns a large inventory of aluminum-clad spent nuclear fuel (ASNF) in interim storage pending ultimate disposition, with more being generated by currently operating research reactors. Dry storage in sealed DOE Standard Canisters is being investigated as an approach for long-term interim storage and/or disposition in a repository for ASNF. A primary challenge for ASNF storage is the presence of aluminum (oxy)hydroxide layers formed on the cladding surfaces during water exposure in the reactor and in wet storage, which forms a reservoir of chemisorbed water not readily removed at low (<100°C) drying temperatures. Free, physisorbed, and chemisorbed water are all susceptible to radiolytic breakdown under irradiation and can release hydrogen gas. Identifying the likely range of (oxy)hydroxide loadings on ASNF that may be placed in dry storage will help to ensure that the impact of the (oxy)hydroxide is adequately accounted for while avoiding over conservatism and enable mitigation strategies to be implemented where needed. The current report summarizes information on (oxy)hydroxide thicknesses and characteristics from the literature and from recent measurements taken in the present research campaign. In general, corrosion studies have indicated that the corrosion and oxide buildup on aluminum are affected by numerous conditions, including pH, temperature and heat flux, coolant flowrates, irradiation (in-reactor vs. unirradiated tests), duration of water exposure, and the amount of oxide already on the surface. Some of these factors are interrelated (e.g., the local temperature, heat flux, and coolant flowrate). Observations of the impact of irradiation (in-reactor versus ex-reactor measurements) on corrosion and oxide thickness are mixed, but multiple studies indicate that there is a significant difference between in-reactor and ex-reactor corrosion kinetics, even when other operating conditions such as pH, flowrate, heat flux, etc., simulate those in a reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sister Rod Destructive Examinations (FY22) Appendix B: Segmentation, Defueling, Metallographic Data and Total Cladding Hydrogen

This report documents work performed under the Spent Fuel and Waste Disposition’s Spent Fuel and Waste Science and Technology program for the US Department of Energy (DOE) Office of Nuclear Energy (NE). This work was performed to fulfill Level 2 Milestone M2SF-23OR010201024, “FY22 Report on ORNL Sibling Rod Testing Results,” within work package SF-23OR01020102 and is an update to the work reported in M2SF-22OR010201047, M2SF-21OR010201032, M2SF-19ORO010201026, and M2SF 19OR010201028. As a part of the DOE-NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWd/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy. The SNF rods, called sister rods or sibling rods are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO ® , and M5 ® . Appendix B provides detailed information regarding defueling activities, metallographic imaging and measurements, and total cladding hydrogen measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Independent Technical Review of INL Aluminum-Clad Spent Nuclear Fuel (ASNF) Oxide Layer Radiolytic Gas Generation Resolution: Task 2

PNNL staff performed an independent technical review (ITR) of the aluminum-clad spent nuclear fuel (ASNF) program Task 2. The objective of Task 2 is to determine G-values for the radiolytic production of gaseous molecular hydrogen (H 2 ) from the aluminum oxyhydroxide layers present on ASNF cladding. The G-values need to be defensible, bounding, but not overly conservative. As part of the ITR, the team reviewed program documents, Task 2 work plans, and results to date. In addition, the team held three separate video conferences with the program research staff to ask clarifying questions and obtain additional detail. The PNNL ITR team concludes that if the program follows the methodology and rigor outlined in the test matrices, the program will develop G-values for a defensible technical basis of extended storage of ASNF. Recommendations for improvement are given.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigation of Degradation Mechanisms of Cr-coated Zirconium Alloy Cladding in Reactivity-Initiated Accident

Reactivity-initiated accident testing has been performed on two baseline fuel rodlets which were fabricated from Zr-4 cladding and utilized fresh UO 2 fuel pellets. These experiments are part of a larger series of transient irradiations to explore Cr-coated zirconium alloy cladding under Reactivity-initiated accident conditions to evaluate ballooning and burst and sever oxidation characteristic of late-stage failure. The first two irradiations have been completed and post-transient examinations have been performed. In one rod, ballooning and burst occurred, along with oxidation. The second rod leaked and as a result did not balloon as much during the transient. This second rod also experienced increased oxidation compared to the first due to higher temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-Temperature SiC Cladding Bowing Irradiation Design and HFIR Readiness

Silicon carbide fiber–reinforced silicon carbide (SiC/SiC) matrix composites are candidate materials for long-term accident-tolerant fuel cladding for use in light water reactors (LWRs). This report documents the design of a dry SiC/SiC composite cladding bowing experiment intended for irradiation in the High Flux Isotope Reactor. The dry experiment allows for testing at representative LWR temperatures for comparison to previous experimental results. This report describes detailed neutronics, thermal, and bowing analyses supporting the irradiation. The design leverages calculations from previous irradiation experiments and production targets for reduced design complexity. The thermal analysis provides a map of SiC thermometer temperatures for comparison during post-irradiation examination to determine the experiment’s irradiation temperatures. Finally, two concepts for introducing localized constraints representative of pressurized water reactor grid spacers are presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Applied Research and Development to Support Open Water Testing at PacWave – Task 5: Development of additively manufactured, functionally graded, corrosion resistant clads for wave energy applications

In this task, we focused on developing corrosion-resistant claddings for wave energy applications. Wave energy systems are exposed to saline conditions, which are corrosive to many metallic structural materials (e.g., carbon steel). Corrosion-resistant (stainless) steels are typically alloyed with >18% chromium (Cr) and >8% nickel (Ni), which dramatically raises material costs and can hinder the development of wave energy systems; thus, coatings are a necessary corrosion protection method for most. Non-metallic coatings (paint, epoxy) have shorter service lives, limited resistance to mechanical stress and wear, plus additional costs of inspection and eventual replacement. Therefore, overlay stainless steel (SS) claddings have a cost-effective use case for protecting components from corrosion, particularly for those that may be subject to mechanical stress / wear and with long service lives.

16 TIDAL AND WAVE POWER↗

Development and Evaluation of Embrittlement Resistant Alloys for Advanced LWR Cladding

The primary challenge preventing the deployment of reactor designs that leverage wrought FeCrAl as an advanced light-water reactor (LWR) cladding is irradiation hardening and embrittlement. Wrought FeCrAl alloys experience a loss of post-irradiation ductility and fracture toughness under low-temperature neutron irradiation (< 350°C) resulting from the combined effects of dislocation loop formation and the irradiation-enhanced precipitation of Cr-rich alpha-prime precipitates throughout the microstructure. Over the past decade, significant improvements in our understanding regarding the effect of Cr and Al content have been enabled through neutron irradiations, but even optimized wrought alloys such as C26M remain vulnerable to brittle failure during storage, transportation, and handling following irradiation. This report summarizes multiple irradiation campaigns initiated over the past 7 years and provides recent insights into the effect of (1) minor alloying composition, (2) alloy processing strategy, (3) crystal structure, and (4) the use of advanced oxide dispersion strengthened (ODS) alloys. The first irradiation campaign irradiated body-centered cubic FeCrAl alloy C26M with and without elements such as Mo and Y. It also included face-centered cubic alumina-forming austenitic (AFA) alloys that have a steeper neutronic penalty but that have far superior high-temperature strength than wrought FeCrAl. Finally, this campaign compared conventional wrought C26M with the same material produced using modern powder metallurgical hotisostatic pressing (PM-HIP). The second irradiation campaign, initiated in 2018, irradiated wrought and FeCrAl-ODS materials up to 50 dpa to assess their irradiation resistance to high-doses. The results of this work indicate that wrought C26M suffers significant degradation following neutron irradiation at LWR-relevant temperatures regardless of Mo and Y content. The PM-HIP variant appears to be more resilient to irradiation-induced ductility loss in comparison with wrought variants but still loses almost all ductility by 8 dpa. Notably, the AFAs retained at least 5% total elongation after irradiation at the same dose and temperature condition, although additional deterioration may be expected at higher fluence levels. FeCrAl-ODS materials show the greatest promise as a transformative longer-term accident-tolerant fuel (LT-ATF) cladding material. The extruded 106ZY10C alloy retained 10% total elongation after 16 dpa irradiation and retained 8% total elongation after 50 dpa. Additional challenges with FeCrAl-ODS alloys also remain, including optimization of end cap joining methodologies, enhancement of fracture toughness, scaling production to prove economic viability, and optimizing post-pilger heat treatments to maximize ductility and irradiation resistance. This series of irradiations demonstrates the efficacy of the LWR testbed available within the United States for the rapid irradiation and down-selection of LT-ATF candidates. As the country rapidly accelerates its timeline for the deployment of advanced reactor concepts, the effective utilization of the High Flux Isotope Reactor for separate-effects style irradiations should continue to be prioritized to answer the final questions pertaining to LT-ATF candidates necessary for the deployment of advanced boiling water reactors and small modular reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Extension of Clad Damage Propagation Model for Fission Gas Dispersal and Two-Phase Flow Effects in MOOSE SubChannel Module

This report presents an extension of the Clad Damage Propagation (CDAP) model implemented in the MOOSE SubChannel Module (SCM) to capture post-failure fission-gas dispersal and two-phase flow effects in sodium-cooled fast reactor assemblies. The extended model tracks discharged gas axially and radially, computes channel-averaged flow quality and void fraction using a Lockhart–Martinelli framework, evaluates two-phase frictional pressure-drop multipliers, determines inlet mass-flow degradation under fixed core pressures, and applies an intensified-void-based heat-transfer degradation to affected fuel pins. Radial plume expansion is parameterized using mineral-oil jet experiments mapped to sodium conditions via Reynolds–Weber similarity. Implementation details are documented, along with the new methods and user inputs needed to control plume mapping and two-phase behavior. Demonstration simulations for 19- and 37-pin bundles show that breach size and inlet velocity strongly influence propagation potential: small breaches (≤0.5 mm) produce limited degradation while larger breaches (~1 mm) can drive oscillatory temperature spikes and enhanced failure propagation, especially at higher velocities. These results demonstrate that the extended CDAP model provides a more complete framework for quantifying cladding damage propagation and evaluating propagation potential in transient scenarios. The approach remains computationally efficient, consistent with subchannel-level analysis, yet incorporates sufficient physics to bridge localized post-failure effects with bundle- and assembly-scale degradation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Single Mode Air-Clad Single Crystal Sapphire Optical Fiber

The observation of single mode propagation in an air-clad single crystal sapphire optical fiber at wavelengths at and above 783 nm is presented for the first time. A high-temperature wet acid etching method was used to reduce the diameter of a 10 cm length of commercially-sourced sapphire fiber from 125 micrometers to 6.5 micrometers, and far-field imaging provided modal information at intervals as the fiber diameter decreased. Modal volume was shown to decrease with decreasing diameter, and single mode behavior was observed at the minimum diameter achieved. While weakly-guiding approximations are generally inaccurate for low modal volume optical fiber with high core-cladding refractive index disparity, consistency between these approximations and experimental results was observed when the effective numerical aperture was measured and substituted for the theoretical numerical aperture in weakly-guiding approximation calculations. With the demonstration of very low modal volume in sapphire at fiber diameters much larger than anticipated by legacy calculations, the resolution of sapphire fiber distributed sensors may be increased and other sensing schemes requiring very low modal volume, such as fiber Bragg gratings, may be realized in extreme environment applications.

36 MATERIALS SCIENCE↗

Mass accretion and nested array dynamics from Ni-Clad Ti-Al wire array Z pinches.

Analysis of 50 mm diameter wire arrays at the Z Accelerator has shown experimentally the accretion of mass in a stagnating z pinch and provided insight into details of the radiating plasma species and plasma conditions. This analysis focused on nested wire arrays with a 2:1 (outeninner) mass, radius, and wire number ratio where Al wires were fielded on the outer array and Ni-clad Ti wires were fielded on the inner array.In this presentation, we will present analysis of data from other mixed Al/Ni-clad Ti configurations to further evaluate nested wire array dynamics and mass accretion. These additional configurations include the opposite configuration to that described above (Ni-clad Ti wires on the outer array, with Al wires on the inner array) as well as higher wire number Al configurations fielded to vary the interaction of the two arrays. These same variations were also assessed for a smaller diameter nested array configuration (40 mm). Variations in the emitted radiation and plasma conditions will be presented, along with a discussion of what the results indicate about the nested array dynamics. Additional evidence for mass accretion will also be presented.

43 PARTICLE ACCELERATORS↗

Nondestructive Evaluation on Hydrided LWR Fuel Cladding by Small Angle Incoherent Neutron Scattering of Hydrogen

A non-destructive neutron scattering method was developed to precisely measure the uptake of total hydrogen in nuclear grade Ziraloy-4 cladding. The hydriding apparatus consists of a closed stainless steel vessel that contains Zr alloy specimens and H gas. By controlling the initial H gas pressure in the vessel and the temperature profile, target H concentrations from tens of ppm to a few thousands of wppm have been successfully achieved. Following H charging, the H content of the hydrided specimens was measured using the vacuum hot extraction method (VHE), by which the samples with desired H concentration were selected for the neutron study. Small angle neutron incoherent scattering (SANIS) were performed in the High Flux Isotope Reactor at Oak Ridge national Laboratory (ORNL). Our study indicates that a very small amount ( 20 ppm) H in commercial Zr cladding can be measured very accurately in minutes for a wide range of H concentration by a nondestructive method. The H distribution in a tube sample was obtained by scaling the neutron scattering rate with a factor, which is determined by calibration process with direct chemical analysis method on the specimen. This scale factor can be used for future test with unknown H concentration, thus provide a nondestructive method for absolute H concentration determination.

Yan, Yong↗

Method and system for edge cladding of laser gain media

A gain medium operable to amplify light at a gain wavelength and having reduced transverse ASE includes an input surface and an output surface opposing the input surface. The gain medium also includes a central region including gain material and extending between the input surface and the output surface along a longitudinal optical axis of the gain medium. The gain medium further includes an edge cladding region surrounding the central region and extending between the input surface and the output surface along the longitudinal optical axis of the gain medium. The edge cladding region includes the gain material and a dopant operable to absorb light at the gain wavelength.

42 ENGINEERING↗

Characterization of Fuel-Cladding Bond Strength Using Laser Shock

This paper describes new laser-based capabilities for characterization of fuel-cladding bond strength in nuclear fuels, and presents preliminary results obtained from studies on as-fabricated monolithic fuel consisting of uranium-10 wt.% molybdenum alloys clad in 6061 aluminum by hot isostatic pressing. Two complementary experimental methods are employed, laser-shock testing and laser-ultrasonic imaging. Measurements are spatially localized, non-contacting and require minimum specimen preparation, and are therefore ideally suited for applications involving radioactive materials, including irradiated materials. The theoretical principles and experimental approaches employed in characterization of nuclear fuel plates are described. The ability to measure layer thicknesses, elastic properties of the constituents, and the location and nature of laser-shock induced debonds is demonstrated, and preliminary bond strength measurement results are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

PRELIMINARY EVALUATION OF FeCrAl CLADDING AND U-Si FUEL FOR ACCIDENT TOLERANT FUEL CONCEPTS

Since the accident at the Fukushima Daiichi Nuclear Power Station, enhancing the accident tolerance of light water reactors (LWRs) has become an important research topic. In particular, the community is actively developing enhanced fuels and cladding for LWRs to improve safety in the event of accidents in the reactor or spent fuel pools. Fuels with enhanced accident tolerance are those that, in comparison with the standard UO2-zirconium alloy system, can tolerate loss of active cooling in the reactor core for a considerably longer time period during design-basis and beyond design-basis events while maintaining or improving the fuel performance during normal operations and operational transients. This paper presents early work in developing thermal and mechanical models for two materials that may have promise: U-Si for fuel, and FeCrAl for cladding. These materials would not necessarily be used together in the same fuel system, but individually have promising characteristics. BISON, the finite element-based fuel performance code in development at Idaho National Laboratory, was used to compare results from normal operation conditions with Zr-4/UO2 behavior. In addition, sensitivity studies are presented for evaluating the relative importance of material parameters such as ductility and thermal conductivity in FeCrAl and U-Si in order to provide guidance on future experiments for these materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of a Clad Activation Capability in BISON using ORIGEN

This work describes the ongoing coupling work establishing ORIGEN as a physics module for depletion, activation, and decay in the MOOSE/BISON fuel performance code. The current phase has focused on the implementation of an activation model, mainly intended for evaluation and comparison of accident tolerant cladding designs within a single fuel performance framework. The next phase will develop a capability for fuel depletion. New aspects of this work include: investigation of how to allow the high-fidelity ORIGEN capability to be interoperable extension of existing lower-fidelity cladding models (e.g. based only on fast fluence), introduction of recalculation thresholds to reduce computational cost during multi-physics iterations, and runtime experiments to assess the cost of this additional physics relative to the baseline MOOSE/BISON fuel performance calculations. The current results show activation increases runtime by a factor of approximately 7, but additional optimizations, discussed in the conclusions, are possible.

Wieselquist, William↗