Search NASA⌕ Search

SEARCH · Search NASA

Results for “DYNAMIC MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

An extended supersonic combustion model for the dynamic analysis of hypersonic vehicles

The development of an advanced dynamic model for aeroelastic hypersonic vehicles powered by air breathing engines requires an adequate engine model. This report provides a discussion of some of the more important features of supersonic combustion and their relevance to the analysis and design of supersonic ramjet engines. Of particular interest are those aspects of combustion that impact the control of the process. Furthermore, the report summarizes efforts to enhance the aeropropulsive/aeroelastic dynamic model developed at the Aerospace Research Center of Arizona State University by focusing on combustion and improved modeling of this flow. The expanded supersonic combustor model described here has the capability to model the effects of friction, area change, and mass addition, in addition to the heat addition process. A comparison is made of the results from four cases: (1) heat addition only; (2) heat addition plus friction; (3) heat addition, friction, and area reduction, and (4) heat addition, friction, area reduction, and mass addition. The relative impact of these effects on the Mach number, static temperature, and static pressure distributions within the combustor are then shown. Finally, the effects of frozen versus equilibrium flow conditions within the exhaust plume is discussed.

Bossard, J. A.↗
NASA NTRS1996

The AFDD International Dynamic Stall Workshop on Correlation of Dynamic Stall Models with 3-D Dynamic Stall Data

A variety of empirical and computational fluid dynamics two-dimensional (2-D) dynamic stall models were compared to recently obtained three-dimensional (3-D) dynamic stall data in a workshop on modeling of 3-D dynamic stall of an unswept, rectangular wing, of aspect ratio 10. Dynamic stall test data both below and above the static stall angle-of-attack were supplied to the participants, along with a 'blind' case where only the test conditions were supplied in advance, with results being compared to experimental data at the workshop itself. Detailed graphical comparisons are presented in the report, which also includes discussion of the methods and the results. The primary conclusion of the workshop was that the 3-D effects of dynamic stall on the oscillating wing studied in the workshop can be reasonably reproduced by existing semi-empirical models once 2-D dynamic stall data have been obtained. The participants also emphasized the need for improved quantification of 2-D dynamic stall.

Tan, C. M.↗
NASA NTRS1987

A computer program for model verification of dynamic systems

Dynamic model verification is the process whereby an analytical model of a dynamic system is compared with experimental data, and then qualified for future use in predicting system response in a different dynamic environment. There are various ways to conduct model verification. The approach adopted in MOVER II employs Bayesian statistical parameter estimation. Unlike curve fitting whose objective is to minimize the difference between some analytical function and a given quantity of test data (or curve), Bayesian estimation attempts also to minimize the difference between the parameter values of that function (the model) and their initial estimates, in a least squares sense. The objectives of dynamic model verification, therefore, are to produce a model which: (1) is in agreement with test data, (2) will assist in the interpretation of test data, (3) can be used to help verify a design, (4) will reliably predict performance, and (5) in the case of space structures, facilitate dynamic control.

Chrostowski, J. D.↗
NASA NTRS1993

Dynamic subgrid-scale modeling for high-speed transitional boundary layers

The subgrid scales are modeled dynamically in a large-eddy simulation of transitional boundary-layer flow along a hollow cylinder at a Mach number of 4.5. The behavior of the dynamic-model coefficients, which is determined from local information in the resolved field, is investigated through both an a priori test with direct numerical simulation data for the same case and a complete large-eddy simulation. Both contractions proposed by Germano et al. (1991) and Lilly (1992) are used for the unique determination of the coefficients of the dynamic model, and their results are compared and assessed. The behavior, as well as the energy cascade of the subgridscale field structure, is investigated at various stages of the transition process.

El-Hady, Nabil M.↗
NASA NTRS2020

Development and Verification of a Pipeline for Modeling Flexible Multibody Dynamics

This project was proposed by Jet Propulsion Laboratory (JPL) personnel in response to a call from the NASA Engineering and Safety Center (NESC) Chief Engineer at JPL for discipline-advancing work. The work described in this NESC Final Assessment Report was requested to improve the efficiency and accuracy of analyses to support the dynamic modeling of complex aerospace systems.

Dynamic Modeling; Flexible Multibody; Finite Eleme↗
NASA NTRS1989

Aeroelastic analysis of prop fan blades with a semiempirical dynamic stall model

The time-history response of a propfan wind-tunnel model with dynamic stall was studied analytically. The response obtained from the analysis was compared with available experimental data. The governing equations of motion were formulated in terms of blade normal modes calculated using the COSMIC-NASTRAN computer code. The response analysis considered the blade plunging and pitching motions. The lift, drag, and moment coefficients for angles of attack below the static stall angle were obtained from a quasi-steady theory. For angles above static stall angles, a semiempirical dynamic stall model based on a correction to the angle of attack was used to obtain lift, drag, and moment coefficients. Using these coefficients, the aerodynamic forces were calculated at a selected number of strips, and integrated to obtain the total generalized forces. The combined momentum-blade element theory was used to calculate the induced velocity. The semiempirical stall model predicted a limit cycle oscillation near the setting angle at which large vibratory stresses were observed in an experiment. The predicted mode and frequency of oscillation also agreed with those measured in the experiment near this setting angle. The results also correlated well with the other published data that used a semiempirical dynamic stall model based on a synthesized procedure.

Reddy, T. S. R.↗
NASA NTRS1991

From wind to superwind - The evolution of mass-loss rates for Mira models

Dynamical atmosphere models were calculated for a large grid of variables with Mira-like properties satisfying the Iben radius-luminosity-mass relationship for evolving AGB stars. Their masses ranged from 0.7 to 2.4 solar masses, and their periods from 150 to 800 days. All were fundamental-mode pulsators, had solar metallicity, and included effects of dust. The mass-loss rate increases as an approximately exponential function of time, reaching 0.00001-0.0001 solar masses/yr. Further evolution is dominated by the powerful wind, which strips the star's envelope from the core. This 'superwind', a remarkably robust effect, occurs for all initial stellar masses and all modeling parameters that have been tested. Models with very low metallicity also show the effect, but at higher luminosities, which has intriguing implications for the number of supernovae in early low-metallicity populations and for the chemical evolution of galaxies.

Bowen, G. H.↗
NASA NTRS1993

Large-eddy simulation of laminar-turbulent breakdown at high speeds with dynamic subgrid-scale modeling

The laminar-turbulent breakdown of a boundary-layer flow along a hollow cylinder at Mach 4.5 is investigated with large-eddy simulation. The subgrid scales are modeled dynamically, where the model coefficients are determined from the local resolved field. The behavior of the dynamic-model coefficients is investigated through both an a priori test with direct numerical simulation data for the same case and a complete large-eddy simulation. Both formulations proposed by Germano et al. and Lilly are used for the determination of unique coefficients for the dynamic model and their results are compared and assessed. The behavior and the energy cascade of the subgrid-scale field structure are investigated at various stages of the transition process. The investigations are able to duplicate a high-speed transition phenomenon observed in experiments and explained only recently by the direct numerical simulations of Pruett and Zang, which is the appearance of 'rope-like' waves. The nonlinear evolution and breakdown of the laminar boundary layer and the structure of the flow field during the transition process were also investigated.

El-Hady, Nabil M.↗
NASA NTRS1989

Analysis of an unswept propfan blade with a semiempirical dynamic stall model

The time history response of a propfan wind tunnel model with dynamic stall is studied analytically. The response obtained from the analysis is compared with available experimental data. The governing equations of motion are formulated in terms of blade normal modes which are calculated using the COSMIC-NASTRAN computer code. The response analysis considered the blade plunging and pitching motions. The lift, drag and moment coefficients for angles of attack below the static stall angle are obtained from a quasi-steady theory. For angles above static stall angles, a semiempirical dynamic stall model based on a correction to angle of attack is used to obtain lift, drag and moment coefficients. Using these coefficients, the aerodynamic forces are calculated at a selected number of strips, and integrated to obtain the total generalized forces. The combined momentum-blade element theory is used to calculate the induced velocity. The semiempirical stall model predicted a limit cycle oscillation near the setting angle at which large vibratory stresses were observed in an experiment. The predicted mode and frequency of oscillation also agreed with those measured in the experiment near the setting angle.

Reddy, T. S. R.↗
DOE OSTI2026

Applying Particle Swarm Optimization and Extended Kalman Filtering to Model Kaplan Generation Dynamics for Hydropower Systems

Variable renewable generation is increasing the need for hydropower plants to provide fast and flexible grid support, which places new demands on plant-level dynamic models used for monitoring, control, and operational decision-making. This need is especially important for hydroelectric systems, where turbine and generator dynamics are strongly coupled, nonlinear, and time-varying, making accurate real-time representation difficult. To address this problem, this paper develops a digital twin (DT) framework for a synchronous generator–Kaplan turbine system using an explicit separation of slow turbine dynamics and fast generator dynamics. The turbine subsystem is represented by a six-coefficient model, whose parameters are identified offline using particle swarm optimization, while the generator subsystem is updated online through an extended Kalman filter for real-time state and parameter estimation. These models are integrated within a closed-loop simulation that includes a proportional–integral–derivative–double-derivative governor and excitation system, allowing the DT to track plant behavior under realistic operating conditions. Unlike prior studies that treat turbine and generator modeling separately or rely mainly on simulated inputs, the proposed framework is validated using real operational data from a hydropower plant. Results show that the DT reproduces terminal voltage, active power, and reactive power with a normalized root mean square error of approximately 5%. This hybrid offline–online formulation constitutes the main contribution of the work, providing an adaptive and practically deployable DT for hydropower systems with direct relevance to control improvement, performance monitoring, and grid-support applications under high renewable penetration.

13 HYDRO ENERGY↗
NASA NTRS1987

On incorporating damping and gravity effects in models of structural dynamics of the SCOLE configuration

The damping for structural dynamic models of flexible spacecraft is usually ignored and then added after modal frequencies and mode shapes are calculated. It is common practice to assume the same damping ratio for all modes, although it is known that damping due to bending and that due to torsion are sometimes ignored. Two methods of including damping in the modeling process from its onset are examined. First, the partial derivative equations of motion are analyzed for a pinned-pinned beam with damping. The end conditions are altered to handle bodies with mass and inertia for the Spacecraft Control Laboratory Experiment (SCOLE) configuration. Second, a massless beam approximation is used for the modes with low frequencies, and a clamped-clamped system is used to approximate the modes for arbitrarily high frequency. The model is then modified to include gravity effects and is compared with experimental results.

Taylor, Larry↗
NASA NTRS1990

External nozzle flap dynamic load measurements on F-15 S/MTD model

Dynamic pressure loads were obtained on 1/12 scale models of the F-15B production aircraft and the F-15 S/MTD experimental aircraft with rectangular nozzles and canards. Flight Mach numbers from 0.51 to 1.20 were studied for aircraft angles of attack from 0 to 10 deg and nozzle pressure ratios from 1.00 to 5.09. The results show that dynamic levels are lower in the internozzle region of twin rectangular nozzles than are levels found with twin axisymmetric nozzles. At other locations, the levels associated with both geometries are of the same order of magnitude when normalized by aircraft dynamic Q. At Mach number of 0.51, the loads spectrum is dominated by plume shock noise processes for both geometries. Above Mach 0.51, this mechanism is associated with either vortex bursting from a forward location or turbulent boundary layer separation over the nozzle external flaps. At supersonic speeds both geometries show significantly decreased load levels.

Seiner, John M.↗
DOE OSTI2025

Moving beyond post hoc explainable artificial intelligence: a perspective paper on lessons learned from dynamical climate modeling

AI models are criticized as being black boxes, potentially subjecting climate science to greater uncertainty. Explainable artificial intelligence (XAI) has been proposed to probe AI models and increase trust. In this review and perspective paper, we suggest that, in addition to using XAI methods, AI researchers in climate science can learn from past successes in the development of physics-based dynamical climate models. Dynamical models are complex but have gained trust because their successes and failures can sometimes be attributed to specific components or sub-models, such as when model bias is explained by pointing to a particular parameterization. We propose three types of understanding as a basis to evaluate trust in dynamical and AI models alike: (1) instrumental understanding, which is obtained when a model has passed a functional test; (2) statistical understanding, obtained when researchers can make sense of the modeling results using statistical techniques to identify input–output relationships; and (3) component-level understanding, which refers to modelers' ability to point to specific model components or parts in the model architecture as the culprit for erratic model behaviors or as the crucial reason why the model functions well. We demonstrate how component-level understanding has been sought and achieved via climate model intercomparison projects over the past several decades. Such component-level understanding routinely leads to model improvements and may also serve as a template for thinking about AI-driven climate science. Currently, XAI methods can help explain the behaviors of AI models by focusing on the mapping between input and output, thereby increasing the statistical understanding of AI models. Yet, to further increase our understanding of AI models, we will have to build AI models that have interpretable components amenable to component-level understanding. We give recent examples from the AI climate science literature to highlight some recent, albeit limited, successes in achieving component-level understanding and thereby explaining model behavior. The merit of such interpretable AI models is that they serve as a stronger basis for trust in climate modeling and, by extension, downstream uses of climate model data.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1976

Method of discrete modeling and its application to estimation of TF30 engine variables

A method of discrete modeling is presented that effectively isolates steady state model accuracy from dynamic model accuracy. The steady state model may be generated from the engine design equations with any desired degree of accuracy. The dynamic model is generated by applying a step disturbance of a manipulated variable to an open loop engine simulation. The sampled response of the variable is combined with the steady state model's response to form a set of weighting factors. These weighting factors are then used to weight past values of the manipulated variable, thus forming the dynamic model. The method is used to estimate various TF30-P-3 engine variables. A dynamic trim function is developed to compensate for the dynamic nonlinearities of the variables as well as for inaccuracies in dynamic definition. The trim function is shown to be realted to the square root of the sum of the squares of the weighting factors obtained at various engine operating conditions. Finally, the estimation of variables without dynamic modeling is discussed.

Arpasi, D. J.↗
NASA NTRS1992

Characteristics of 3-D transport simulations of the stratosphere and mesosphere

A 3D mechanistic, primitive-equation model of the stratosphere and mesosphere is coupled to an offline spectral transport model. The dynamics model is initialized with and forced by observations so that the coupled models may be used to study specific episodes. Results are compared with those obtained by transport online in the dynamics model. Although some differences are apparent, the results suggest that coupling of the models to a comprehensive photochemical package will provide a useful tool for studying the evolution of constituents in the middle atmosphere during specific episodes.

Fairlie, T. D. A.↗